Contents of the box:
The Docking Station
USB Micro-AB to A cable
Features: Front
Spare battery well
This Guide
PX3001
Desktop Docking Station
Quick Start Guide
November 14, 2008 PN: 8100176.A
I
S
O
9
0
0
1
C
e
r
t
i
f
i
e
d
Q
u
a
l
i
t
y
M
a
n
a
g
e
m
e
n
t
S
y
s
t
e
m
Features: Back, Ports, And Battery Charge Well
NEO compartment
Docking connector
Power adaptor
and plugs
Battery contacts
Spare battery well
Drain hole
Drain hole
Micro-USB connector
DC In port
Mounting The Desktop Docking Station
The Desktop Docking Station can be
fi xed to the optional Wall Mount Bracket
NEO compartment
(model PX3011), or to another surface,
by two broad-headed screws.
Getting Started
Choose a plug for the universal power adaptor. The
1
adaptor may already be fi tted with the plug you need.
1. Press the button on
the power adaptor to
release the plug.
2. Pivot the existing plug
out of the adaptor.
Connect the Docking Station
2
to external power.
:
3. Pivot the desired plug into
the adaptor until it clicks.
Insert the NEO to charge its battery.
3
Slide the NEO into the Docking
Station until it latches.
Note: Use only the universal
AC power supply approved by
Psion Teklogix for use with the
Docking Station.
.
Insert the spare battery.
4
Note: During charge, the LED indicator on the NEO
is YELLOW until charging reaches 75%.
Between 75% and 95% the indicator fl ashes
GREEN slowly, and, above 95%, the indicator is
GREEN continuously.
The LED indicator on the Docking Station behaves
the same when a spare battery is being charged.
Note: Full battery performance is only reached after
the fi rst few charge/discharge cycles.
Over
LED indicator
Docking connector
Rubber feet (quantity 4)
Mounting holes (quantity 2)
Mounting screw (quantity 2)
Note: The position of
the mounting holes is
indicated by markings on
the front and sides of the
Desktop Docking Station.
Insert the screws into the holes on the base of the unit,
then slide the unit towards the back to secure it.
DC Input
Allow the NEO and the spare battery to charge
for three hours before fi rst use.
0 - 40 °C
32 - 104 °F
3 h
To connect the Docking Station to a host computer:
The NEO in the Docking Station acts as a USB Client.
Location Guide For Mounting Screws
™
1. Connect the smaller end
of the USB cable to the
Docking Station.
Dimensions Of Mounting Screws
Maximum diameter of screw head:
Maximum height of screw head:
0.45 cm (0.18 in)
Maximum height between screw
head and mounting surface:
0.4 cm (0.16 in)
Maximum diameter of screw shaft:
USB Host computer
2. Connect the fl at
end of the USB cable
to the host computer.
1.05 cm (0.41 in)
0.65 cm (0.26 in)
Rubber feet
Mounting
holes
Front of Docking
Station
0.512 in
(1.30 cm)
2.20 in (5.60 cm)
5.20 in (13.2 cm)
2.16 in (5.50 cm)
3.44 in (8.75 cm)
The mounting screws are M4 x 6mm panhead screws.
Outline of
Desktop Docking
Station
0.512 in
(1.30 cm)
2.09 in
(5.30 cm)
2.13 in
(5.40 cm)
0.61 in
(1.55 cm)
Psion Teklogix and NEO
are trademarks of Psion
Teklogix Inc. Other product
names mentioned in this
document are trademarks
or registered trademarks of
other hardware, software,
or service providers and are
used herein for identifi cation
purposes only.
8100176
8100176
Rev. A
PX3001
Desktop Docking Station
Quick Start Guide
November 14, 2008 PN: 8100176.A
ISO 9001 Certifi ed
Quality Management System
Loading...