Zebra DS4208 Quick Start Manual
DS4208
Quick Start Guide
http://www.zebra.com/ds4208
POST IN WORK AREAPOST IN WORK AREA
Attach Cable
STEP 1 - ATTACH CABLE TO SCANNER
Remove Cable (to change interface)
See Product Reference Guide for detailed information
Note: An audible click sounds when the shielded cable is inserted correctly.
STEP 2 -CONNECT CABLE TO A HOST
NOTE: Cables may vary depending on configuration.
RS-232 Keyboard Wedge USB
IBM 46XX
STEP 3 - SET UP INTERFACE (Scan Host Bar Codes)
Important: Out of box, RS-232 and USB interfaces require no bar code scan setup. Bar codes are provided for complex programming or interface changes.
USB
Scan ONE of the bar codes below Scan ONE of the bar codes below
IBM HAND-HELD USB
HID KEYBOARD EMULATION
Symbol Native API (SNAPI) without Imaging Interface
Keyboard Wedge
IBM AT Notebook
IBM PC/AT and IBM PC COMPATIBLE
RS-232
Scan ONE of the bar codes below
OPOS/JPOS
STANDARD RS-232
IBM 46XX
Scan ONE of the
PORT 5B
PORT 9B
bar codes below
ADD AN ENTER KEY (CARRIAGE RETURN/LINE FEED)
To add an ENTER key after scanned data, scan all THREE bar codes below in numerical order.
1 2 3
SCAN OPTIONS
<DATA><SUFFIX> ENTER
ADD A TAB KEY
To add a Tab key after scanned data, scan all THREE Enter key bar codes above in numerical order then scan all FIVE bar codes below in numerical order.
1 2
SCAN SUFFIX
7
3 4
0
0
5
9
INTELLISTAND SET DEFAULTS
OPTIMUM SCANNING
123SCAN
2
SCANNER INDICATIONS
LED Indications
Standard Use
Off
Scanner is on and ready to scan,
or no power to scanner
Beeper Indications
Standard Use
Low/medium/high beeps Short beep 4 low beeps
Power up Bar code symbol decoded
Parameter Menu Scanning
High/low/high/low beeps
Successful parameter setting Keyboard parameter
Green
Bar code is successfully decoded
(if decode beeper enabled)
High/low beeps
selected.
Red
Transmission error
Transmission error detected, data is ignored
Low/high beeps
Input error; incorrect bar code,
programming sequence,
or Cancel scanned
Return to Factory Defaults
SET DEFAULTS
Troubleshooting
Scanner not working
No power to scanner
Check system power;
ensure power supply,
if required, is connected
Scanner decoding bar code, but data not transmitting to host
Scanner not programmed for correct host interface
Scan appropriate host parameter
bar codes
Incorrect interface cable used Interface/power cables are loose
Ensure that correct
interface cable is used
TROUBLESHOOTING
Ensure all cable connections
are secure
Interface cable is loose
Ensure all cable connections
are secure
123Scan2 is an easy-to-use, PC-based software
tool that enables rapid and easy customized
setup via a bar code or USB cable. For more
information, visit:
http://www.zebra.com/123Scan
Scanned data incorrectly displayed on host
Scanner not programmed for correct host interface
Scan appropriate host parameter
bar codes
Scanner not decoding bar code
Scanner not programmed
for bar code type
Ensure scanner is programmed
to read type of bar code
being scanned
Bar code unreadable
Ensure bar code not
defaced; try scanning test
bar code of same bar
code type
2
.
Distance between scanner
and bar code incorrect
Move scanner closer to or
further from bar code
RECOMMENDED USAGE GUIDE - OPTIMUM BODY POSTURE
Avoid Extreme Wrist Angles Avoid ReachingAvoid Bending
AVOID EXTREME WRIST ANGLES
© 2015 Symbol Technologies, Inc.
Zebra reserves the right to make changes to any product to improve reliability, function, or design.
Zebra does not assume any product liability arising out of, or in connection with, the application or use of any
product, circuit, or application described herein. No license is granted, either expressly or by implication,
estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Zebra products might be used. An implied license
exists only for equipment, circuits, and subsystems contained in Zebra products.
Power Supply
Use ONLY a LISTED, Type no. PWRS-14000 (5.2Vdc, 850mA minimum), direct plug-in power supply, marked
Class 2 or LPS (IEC60950-1, SELV). Use of alternative Power Supply will invalidate any approvals given to this
unit and may be dangerous.
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty.
Service Information
If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a
problem with the equipment, they will contact Zebra at:
http://www.zebra.com/support.
For the latest version of this guide go to: http://www.zebra.com/support.
Waste Electrical and Electronic Equipment (WEEE)
English: For EU Customers: All products at the end of their life must be returned
to Zebra for recycling. For information on how to return product, please go to:
http://www.zebra.com/weee.
Bulgarish: За клиенти от ЕС: След края на полезния им живот всички
продукти трябва да се връщат на Zebra за рециклиране. За информация
относно връщането на продукти, моля отидете на адрес:
http://www.zebra.com/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich
životnosti vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení
produktu najdete na webové stránce: http://www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når
de er udtjent. Læs oplysningerne om returnering af produkter på:
http://www.zebra.com/weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer
Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur
Rücksendung von Produkten finden Sie unter http://www.zebra.com/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας
ζωής τους, πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για
περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος,
επισκεφθείτε τη διεύθυνση http://www.zebra.com/weee στο Διαδίκτυο.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada
taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote
tagastamise kohta külastage palun aadressi: http://www.zebra.com/weee.
Español: Para clientes en la Unión Europea: todos los productos deberán
entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea
más información sobre cómo devolver un producto, visite:
http://www.zebra.com/weee.
Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de
vie doivent être retournés à Zebra pour recyclage. Pour de plus amples
informations sur le retour de produits, consultez : http://www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del
rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il
riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito
Web: http://www.zebra.com /weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir
POST IN WORK AREAPOST IN WORK AREA
jānogādā atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu
nogādāšanu Zebra, lūdzu, skatiet: http://www.zebra.com/weee.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A
http://www.zebra.com
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a
registered trademark of Symbol Technologies, Inc., a Zebra Technologies company.
© 2015 Symbol Technologies, Inc.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi
būti grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti
gaminį, rasite: http://www.zebra.com/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra
vállalathoz kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának
módjával kapcsolatos tudnivalókért látogasson el a http://www.zebra.com/weee
weboldalra.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu
tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif
għandek tirritorna l-prodott, jekk jogħġbok żur: http://www.zebra.com/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van
hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg
http://www.zebra.com/weee voor meer informatie over het terugzenden van
producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji
nale¿y zwróciæ do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu
produktów znajduj¹ siê na stronie internetowej http://www.zebra.com/weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser
devolvidos à Zebra para reciclagem. Para obter informações sobre como devolver
o produto, visite: http://www.zebra.com/weee.
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de
funcţionare, trebuie returnate la Zebra pentru reciclare. Pentru informaţii despre
returnarea produsului, accesaţi: http://www.zebra.com/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí
doby ich životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o
vrátení výrobkov nájdete na: http://www.zebra.com/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe
vrniti podjetju Zebra za reciklažo. Za informacije o vraèilu izdelka obišèite:
http://www.zebra.com/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava
kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen
palauttamisesta on osoitteessa http://www.zebra.com/weee.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste
returneras till Zebra för återvinning. Information om hur du returnerar produkten
finns på http://www.zebra.com/weee.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme
için Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için
lütfen şu adresi ziyaret edin: http://www.zebra.com/weee.
REGULATORY INFORMATION
Scanner Labeling
AVOID BENDING
AVOID REACHING
Health and Safety Recommendations
Ergonomic Recommendations
In order to avoid or minimize the potential risk of ergonomic
Caution:
injury follow the recommendations below. Consult with your local
Health & Safety Manager to ensure that you are adhering to your
company’s safety programs to prevent employee injury.
• Reduce or eliminate repetitive motion.
• Maintain a natural position.
• Reduce or eliminate excessive force.
• Keep objects that are used frequently within easy reach.
• Perform tasks at correct heights.
• Reduce or eliminate vibration.
• Reduce or eliminate direct pressure.
• Provide adjustable workstations.
• Provide adequate clearance.
• Provide a suitable working environment.
• Improve work procedures.
Regulatory Information
This guide applies to Model Number: DS4208.
All Zebra devices are designed to be compliant with rules and regulations in locations they are sold
and will be labeled as required.
Local language translations are available at the following website: http://www.zebra.com/support.
Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the
user’s authority to operate the equipment.
Antennas: Use only the supplied or an approved replacement antenna. Unauthorized antennas,
modifications, or attachments could cause damage and may violate regulations.
LED Devices
Complies with IEC/EN60825-1:2001 & IEC/EN62471:2006
For devices with Class 1M LEDs the following label is used:
Radio Frequency Interference Requirements -FCC
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
FOR HOME OR OFFICE USE
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements - Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Statement of Compliance
Zebra hereby declares that this device is in compliance with all the applicable Directives, 2004/108/EC
2006/95/EC and 2011/65/EU. A Declaration of Conformity may be obtained from
http://www.zebra.com/doc.
TURKISH WEEE Statement of Compliance
EEE Yönetmeliğine Uygundur
Japan (VCCI) - Voluntary Control Council for Interference
Class B ITE
Korea Warning Statement for Class B ITE
Tested to comply
with FCC Standards
Marking and European Economic Area (EEA)
B
72-139230-02 Revision A March 2015
DS4208
http://www.zebra.com/ds4208
Loading...