Zanussi ZWQ 61226 SI User manual

GETTING STARTED?
EASY.
User Manual
ZWQ 61226SI
EN User Manual 2
Washing Machine
RU Инструкция по эксплуатации 18

SAFETY INFORMATION

Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.

CHILDREN AND VULNERABLE PEOPLE SAFETY

This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
Do not let children play with the appliance.
Children aged 3 years and under must be kept away from this
appliance when it is in operation at all times.
Keep all packaging away from children and dispose of it
appropriately.
Keep detergents away from children.
Keep children and pets away from the appliance when the door
is open.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.

GENERAL SAFETY

Do not change the specification of this appliance.
Do not exceed the maximum load of 6 kg (refer to the
"Programme chart" chapter).
The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8 bar (0.8 MPa).
The ventilation opening in the base (if applicable) must not be
covered by a carpet, mat, or any floor covering.
The appliance must be connected to the water mains using the
new supplied hose sets, or other new hose sets supplied by the Authorised Service Centre.
2
Old hose sets must not be reused.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons to avoid an electrical hazard.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to clean
the appliance.
Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects.

SAFETY INSTRUCTIONS

INSTALLATION

• Remove all the packaging and the transit bolts.
• Keep the transit bolts in a safe place. If the appliance is to be moved in future they must be reattached to lock the drum to prevent internal damage.
• Always take care when moving the appliance as it is heavy. Always use safety gloves and enclosed footwear.
• Do not install or use a damaged appliance.
• Follow the installation instruction supplied with the appliance.
• Do not install or use the appliance where the temperature can be less than 0°C or where it is exposed to the weather.
• The floor area where the appliance is to be installed must be flat, stable, heat resistant and clean.
• Make sure that there is air circulation between the appliance and the floor.
• Adjust the feet to have the necessary space between the appliance and the flooring.
• Do not install the appliance where the appliance lid cannot be fully opened.
• Do not put a container to collect possible water leakage under the appliance. Contact the Authorised Service Centre to ensure which accessories can be used.

ELECTRICAL CONNECTION

• The appliance must be earthed.
• Always use a correctly installed shockproof socket.
• Make sure that the parameters on the rating plate are compatible with the electrical ratings of the mains power supply.
• Do not use multi-plug adapters and extension cables.
• Make sure not to cause damage to the mains plug and to the mains cable. Should the mains cable need to be replaced, this must be carried out by our Authorised Service Centre.
• Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation.
• Do not touch the mains cable or the mains plug with wet hands.
• Do not pull the mains cable to disconnect the appliance. Always pull the mains plug.
• This appliance complies with the E.E.C. Directives.

WATER CONNECTION

• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used for a long time, where repair work has been carried out or new devices fitted (water meters, etc.), let the water flow until it is clean and clear.
• Ensure that there are no visible water leaks during and after the first use of the appliance.
USE
WARNING! Risk of injury, electrical
shock, fire, burns or damage to the appliance.
• This appliance is for household use only.
• Follow the safety instructions on the detergent packaging.
3
• Do not put flammable products or items that are
3
1
4
5
2
wet with flammable products in, near or on the appliance.
• Make sure that all metal objects are removed from the laundry.
• Do not wash fabrics which are heavily soiled with oil, grease or other greasy substances. It can damage rubber parts of the washing machine. Prewash such fabrics by hand before loading them into the washing machine.

SERVICE

• To repair the appliance contact an Authorised Service Centre.
• Use original spare parts only.

PRODUCT DESCRIPTION

APPLIANCE OVERVIEW

DISPOSAL

WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the mains electrical and water supplies.
• Cut off the mains electrical cable close to the appliance and dispose of it.
• Remove the door catch to prevent children or pets from becoming trapped in the drum.
• Dispose of the appliance in accordance with local requirements for the disposal of Waste Electrical and Electronic Equipment (WEEE).
Control panel
1
Lid
2
Lid handle
3
Feet for levelling the appliance
4
Rating plate
5
4

CONTROL PANEL

1200
1000
800
20°
987621 3 4 5
A
D
B C

CONTROL PANEL DESCRIPTION

1
On/Off button (On/Off)
2
Programme selection touchpad
3
Temperature selection touchpad
4
Spin selection touchpad
5
Options selection touchpad

DISPLAY

6
Start/Pause touchpad
7
Finish in touchpad (Finish In) Display
8 9
Door locked indicator
A. The time area:
: the programme duration
: the "finish in" time
: the alarm codes
: the message of error
: the programme is completed.
B. The child lock indicator:
• The indicator comes on when you activate this device.
C. The extra rinse indicator:
• The indicator comes on when you activate this option.
D. The Finish In touchpad.
5

PROGRAMME CHART

Programme
Temperature range
30'@30° 30°C
Cottons 90°C - Cold
Cotton Eco
60°C - 40°C
Synthetics 60°C - Cold
Delicates 40°C - Cold
Wool/Handwash
40°C - Cold Refresh 20 min
40°C - 30°C
Mix 20° 20°C
1) Cottons energy saving programme. This programme at a 60ºC with a load of 6 kg is the reference pro­gramme for data entered in the energy label, in compliance with EEC 92/75 standards. Set this pro­gramme to have a good washing results and decrease the energy consumption. The time of the washing programme is extended.
2) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't rotate or doesn't rotate properly, but this is normal for this programme.
3) No temperature indicator is on .
Maximum load Maximum spin
speed
2 kg 800 rpm
6 kg 1200 rpm
6 kg
1)
1200 rpm
2,5 kg 1200 rpm
2,5 kg 1200 rpm
1 kg 1200 rpm
1 kg 1200 rpm
2,5 kg 1200 rpm
Programme description
(Type of load and soil level)
A short cycle for synthetic and delicate items with light soil level or for items to freshen up.
White cotton and coloured cotton. Normal soil and
light soil.
White cotton and fast-coloured cotton. Normal soil. The energy consumption decreases and the time of the washing programme is extended.
Synthetic items or mixed fabric items. Normal soil.
Delicate fabrics such as acrylics, viscose, polyester items. Normal soil.
Machine washable wool, hand washable wool and delicate fabrics with «hand washing» care symbol.
A very short cycle for cotton and synthetic items with light soil level or worn only once.
Special programme for cotton, synthetic and mixed fabrics with light soil. Set this programme to decrease the energy consumption. Make sure that the detergent is for low tem-
perature in order to have good washing results3).
2)
Programme options compatibility
Programme
30'@30°
6
1)
Programme
1)
1) When you set this option, we recommend that you decrease the quantity of the laundry. It is possible to keep the full load but the washing results can be unsatisfactory. Recommended load: cotton: 3 kg, syn­thetics and delicates: 1,5 kg.

CONSUMPTION VALUES

The data in this table are approximate. Different variables can affect the data: the quantity and type of laundry, the water and ambient temperature.
At the start of the programme, the display shows the programme duration for the maxi­mum load capacity. During the washing phase the programme duration is automatically calculated and can be greatly reduced if the laundry load is lower than the maximum load capacity (e.g. Cotton 60°C, maximum load capacity 6 kg, the programme duration exceeds 2 hours; actual load 1 kg, the programme duration will be less than 1 hour). When the appliance is calculating the real programme duration a dot flashes in the dis­play.
Programmes Load (kg)
Energy con-
sumption
(kWh)
Water con-
sumption (litre)
Approximate pro-
gramme duration (mi-
nutes)
Cottons 60°C 6 1,10 56 180 Cotton Energy Saving Pro-
gramme 60°C Cottons 40°C 6 0,65 54 150 Synthetics 40°C 2,5 0,45 46 105 Delicates 40°C 2,5 0,55 46 90
1)
6 0,80 47 246
7
Programmes Load (kg)
Energy con-
sumption
(kWh)
Water con-
sumption (litre)
Approximate pro-
gramme duration (mi-
nutes)
Wool/Handwash 30°C
1) «Cotton Energy Saving programme » at 60°C with a load of 6 kg is the reference programme for the data entered in the energy label, in compliance with EU Commission Directive 95/12/EC and measured according to EN 60456/2005.
Off Mode (W) Left On Mode (W)
0,48 0,48
The information given in the chart above is compliant with the EU Commission regulation 1015/2010 implementing directive 2009/125/EC
1 0,35 50 65

OPTIONS

TEMPERATURE

With this option you can change the default temperature.
Indicator The indicator of the set temperature comes on.

SPIN

With this option you can change the default spin speed.
The indicator of the set speed comes on.
= cold water.
Additional spin options:
No Spin
• Set this option to deactivate all spin phases. Only the drain phase is available.
• The related indicator comes on.
• Set this option for very delicate fabrics.
• The rinses phase uses more water for some washing programmes.
Rinse Hold
• Set this option to prevent the laundry creases.
• The related indicator comes on.
• There is a water in the drum when the programme is completed.
• The drum turns regularly to prevent the laundry creases.
• The lid stays locked. You must drain the water to unlock the lid.

QUICK

With this option you can decrease the programme duration.
Use this option for items with light soil or items to refresh.
The related indicator comes on.

PREWASH

With this option you can add a prewash phase to a washing programme.
Use this option for heavy soil. When you set this option the programme duration increases.
The related indicator comes on.

EASY IRON

The appliance carefully washes and spins the laundry to prevent the creases.
The appliance decreases the spin speed, uses more water and adapts the programme duration to the type of laundry.
The related indicator comes on.

RINSE

With this option you can perform only a last rinse of a selected washing programme.
To drain the water refer to ‘At the end of the programme’.
8
If you set also the Extra Rinse function ( ) the appliance adds two or more rinses.
The related indicator comes on.

DRAIN AND SPIN

With this option you can perform the spin and drain cycle.
This spin phase is suitable to the washing programme you set.
If you set also the No Spin ( ) option, the appliance only drains.

FINISH IN

With this option you can set the number of hours in which you would like your washing programme to be completed.

SETTINGS

You can set from minimum 3 hours to maximum 20 hours.
The display shows the number of hours and the indicator above the button

EXTRA RINSE

With this option you can add some rinses to a washing programme.
Use this option for persons allergic to detergents and in areas where the water is soft.
The related indicator comes on.
is on.
1)

PERMANENT EXTRA RINSE

With this option you can permanently have an extra rinse when you set a new programme.
• To activate/deactivate this option touch the buttons and at the same time until the indicator comes on/goes off.

CHILD LOCK

With this option you can prevent that the children play with the control panel.
• To activate/deactivate this option, touch the buttons and at the same time until the indicator comes on/goes off.
Activate this option after you touch the button : the buttons are locked (except for the button ) .

BEFORE FIRST USE

1. Put a small quantity of detergent in the
compartment for washing phase.
2. Set and start a programme for cotton at the
highest temperature without laundry.
This option stays active even when you switch off the appliance.

ACOUSTIC SIGNALS

The acoustic signals operate when:
• The programme is completed.
• The appliance has a malfunction. To deactivate/activate the acoustic signals,
touch the buttons seconds.
If you deactivate the acoustic signals, they continue operate when the appliance has a malfunction.
This removes all possible dirt from the drum and the tub.
and at the same time for 4
1) See in "Settings" how to activate this option.
9

DAILY USE

A
WARNING! Refer to Safety chapters.

LOADING THE LAUNDRY

1. Open the appliance lid.
2. Push the button A.
The drum opens automatically.
3. Put the laundry in the drum, one item at a time.
4. Shake the items before you put them in the
appliance.
Make sure not to put too much laundry in the drum.
5. Close the drum and the lid.
CAUTION! Before you close the lid of
your appliance, make sure that you close the drum correctly.

USING DETERGENT AND ADDITIVES

Measure out the detergent and the fabric conditioner.

DETERGENT COMPARTMENTS

Detergent compartment for pre­wash phase.
Detergent compartment for wash­ing phase.
Compartment for liquid additives (fabric conditioner, starch).
CAUTION! Do not exceed the M level.

ACTIVATING THE APPLIANCE

Press and hold for a couple of seconds the On/Off button to activate or deactivate the appliance.
A tune sounds when the appliance is activated. The display shows the word On.

SETTING A PROGRAMME

1. Touch the programme button and set the
programme:
• The indicator of the button flashes.
• The display shows the programme duration.
2. If necessary, change the temperature and the spin speed or add available options. When you activate an option, the indicator of the set option comes on.
If you set something incorrect, the display shows the message .

STARTING A PROGRAMME WITHOUT THE FINISH IN OPTION

Touch the button .
• The indicator of the button stops to flash and stays on.
• The programme starts, the lid locks, the indicator is on.
• The drain pump can operate for a short time at the beginning of the washing cycle.
After approximately 15 minutes from the start of the programme:
• The appliance adjusts automatically the programme duration agree with the laundry load.
• The display shows the new value.
10

STARTING A PROGRAMME WITH THE FINISH IN OPTION

1. Touch the button again and again to
choose the number of hours in which you want the washing cycle to be finished.
The display shows the number of hours you set (e.g. ) and the indicator above the button is
on to show that his option is active.
2. Touch the button :
• The door is locked.
• The appliance starts the countdown.
• When the countdown is completed, the programme starts automatically.
You can cancel or change the set of the Finish In option before you touch
the button . After touching the button you can only cancel the
Finish In option.
To cancel the the Finish In option:
a. Touch the button to set the appliance
to pause. The indicator of button flashes.
b. Touch the button until the indicator
above this button goes off. Touch the button again to start the
programme immediately.
When using liquid detergents in combination with the Finish In option, add the liquid detergents with a dosing ball (supplied by the detergent's manufacturer).

INTERRUPTING A PROGRAMME AND CHANGING THE OPTIONS

You can change only some options before they operate.
1. Touch . The indicator of this button flashes.
2. Change the options. If you change any option the Finish In option (if set) will be disabled.
3. Touch again.
The programme continues.

CANCELLING A PROGRAMME

1. Press the button for some seconds to
cancel the programme and to deactivate the appliance.
2. Press the same button again to activate the appliance. Now, you can set a new washing programme.
Before starting the new programme the appliance could drain the water. In this case, make sure that the detergent is still in the detergent compartment, if not fill the detergent again.

OPENING THE LID

While a programme (or the ) operates, the appliance lid is locked. The indicator is on.
CAUTION! If the temperature and level of the water in the drum are too high, you cannot open the lid.
To open the lid during the first minutes of the cycle (or when the operates) :
1. Touch the button to pause the appliance.
2. Wait a couple of minutes until the indicator
goes off.
3. You can open the lid.
4. Close the lid and touch the button again.
The programme (or the ) continues.

AT THE END OF THE PROGRAMME

• The appliance stops automatically.
• The acoustic signal operates (if it is activated).
• In the display comes on.
• The indicator of the button goes off.
• The lid lock indicator blinks (when the lid is
unlocking) and then goes off.
• You can open the lid.
• Remove the laundry from the appliance. Make
sure that the drum is empty.
• Press the button for some seconds to
deactivate the appliance.
• Close the water tap.
• Keep the lid ajar, to prevent the mildew and
odours.
The washing programme is completed, but there is water in the drum:
• The drum turns regularly to prevent the creases
in the laundry.
• The indicator flashes to remind you to drain
the water.
• The lid lock indicator is on. The indicator of
button flashes. The lid stays locked.
11
Loading...
+ 25 hidden pages