Height with worktopcm 85
Height without worktopcm 82
Max depthcm 61
Max depth with door opencm 120
ELECTRICAL CONNECTIONVoltage220-240V/50Hz
POWER OF HEATING ELEMENT1900 W
OVERALL POWER2100 W
WATER SUPPLY PRESSUREminimum7 psi - 49 KN/cm
maximum110 psi - 758 KN/cm
2
2
CAPACITY (STANDARD IEC PLACE SETTINGS)12
CONSUMPTION:Water20 lt
Electricity1.4 kW/h
PID08GB
2
WARNINGS
It is most important that this instruction book
should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move
house and leave the appliance, always ensure that
the book is left with the appliance in order that the
new owner can get to know the functioning of the
appliance and the relevant warnings.
These warnings are provided in the interest of
safety. You MUST read them carefully before
installing or using the appliance.
■ If the appliance is supplied with obvious damage,
consult the supplier before installing it.
■ Any plumbing work required to install this appliance
should be carried out by a qualified plumber or
competent person.
■ Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
■ This appliance is designed to be operated by adults.
■ Care must be taken to ensure that the appliance
does not stand on the electrical supply cable or on
the water inlet and drain hoses.
■ Under no circumstances should you attempt to
repair the machine yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning.
■ This appliance should be serviced only by an
authorised Zanussi Service Center.
■ Before disposing of the appliance, disconnect the
water hose, cut the electrical cable and ensure that
the door cannot close.
■ For proper disposal of the appliance, contact your
local waste collection service.
■ Zanussi dishwashers are designed to be used for
washing normal household utensils. Items that are
contaminated by petrol, paint, steel or iron debris,
corrosive, acidic or alkaline chemicals are not to be
washed in a dishwasher.
■ Under no circumstances should you open the door
whilst, the appliance is in operation. Always turn off
the appliance before opening the door.
However, the dishwasher features a special safety
device which cuts off the water inlet, should the door
be accidentally opened, thus avoiding water leaks.
■ Never touch the heating element during or
immediately after the end of the washing cycle.
■ When finishing loading or unloading close the door,
as an open door can be a hazard.
■ It is dangerous to lean or to sit on the dishwasher
door: the appliance could tip over.
■ Built-in dishwashers only: the appliance must be
secured to the underside of the worktop using the
brackets provided. Failure to do this could result in
an unstable appliance which may cause damage or
injury.
■ Unplug the appliance and turn off the water after
use.
PAV01GB
3
INSTALLATION
Remove all packaging before positioning the
machine.
Positioning
If possible, position the machine next to a water tap
and a drain.
The sides and the back of the dishwasher can rest
against the adjacent furniture or the wall.
The dishwasher features fill and drain hoses which
can be turned either to the left or the right to suit the
installation.
Levelling
Good levelling is essential for correct closure and
sealing of the door.
If the door does not close correctly, loosen or tighten
the adjustable support feet, until the machine is
perfectly level.
Installing and securing the machine under a
kitchen unit (sink-worktop unit)
By removing the machine's worktop, you can install it
under a close fitting sink unit or a pre-existing top, if
the dimensions of the recess correspond to those
shown in the picture.
Then proceed as follows:
Remove the machine worktop by unscrewing the two
front retaining screws, pull from the front and slide out
the rear slots, lifting the worktop.
Insert the machine after adjusting the height and levelling with the adjustable feet. When inserting the machine, ensure that the water inlet and drain hoses are
not kinked or squashed.
570÷600
820
600
IN01
Adjusting the worktop
You can move the worktop forward or backward by 25
mm in order to align the machine with other kitchen
units.
Simply unscrew the two front retaining screws, move
the top to the required position and then retighten the
screws.
IN03
IN05
Caution
Once the machine has been installed, ensure that it
can be accessed easily for servicing.
PIN01GB
4
Water outlet connection
The end of the drain hose can be connected as
follows:
to the sink outlet siphon, securing it if necessary with
a clip;
to a wall outlet provided with vent-hole, minimum
internal diameter 4 cm;
hooked over the edge of the sink using the special
curved plastic guide provided.
The waste connection must be at a height of between
30 cm (minimum) and 100 cm (maximum) from the
floor.
It makes no difference which way the drain hose
faces, either to the right or left of the dishwasher.
Avoid bending or kinking the hose as this could
prevent or slow down the discharge of water.
If you use a drain hose extension it must be no longer
than 2 metres and its internal diameter must be no
smaller than the diameter of the hose provided.
Likewise the internal diameter of the couplings used
for connection to the waste outlet must be no smaller
than the diameter of the drain hose.
Ø 21
Ø 18
Ø 18
Ø 21
min 4 cm
The problem is signalled by a red or yellow indicator
which appears in window (B - ➀ ➁).
If this happens, close the water tap and have the hose
replaced.
Warning: the retaining ring (A - ➀ ➁) must be proper-
ly fitted so as to avoid water leaks.
CA13
A
1
B
2
A
B
C
Note: Only for water supply hoses with lock-fast
safety device to prevent inadvertent loosening.
To detach the hose press yellow lever (C - ➁) and turn
the retaining ring anti-clockwise.
Note: the end of thehose
connected to the machine
can be positioned as required, by simply slackening the retaining ring.
Re-tighten the ring securely
to avoid water leaks.
+ 2 m max
CS01
max 100 cm
min 30 cm
max 100 cm
Water supply connections
This dishwasher may be fed with either hot (max.
60°C) or cold water.
Nevertheless we advise you a cold water supply.
A hot water supply is not always efficient with very
soiled crockery as it shortens the washing programmes a lot.
Feeding the appliance with a hot water supply (max.
60°C) will allow you to obtain considerably shorter
programmes.
For making the connection itself, the coupling nut fitted
to the machine's supply hose is designed to screw
onto either a 3/4 inch gas thread spout, or to a
purpose-made quick-coupling tap such as the PressBlock.
The water pressure must be within the limits given in
the technical specifications, as it will not function
correctly if pressure is outside these specifications.
The water supply hose is fitted with a safety device,
which prevents water from entering the machine
should the inner hose split, due to wear.
CA06
Avoid bends or kinks in the hose, which could prevent
or slow down the flow of water.
If the machine is connected to new pipes or pipes
which have not been used for a long time, you are
advised to run the water for a few minutes before
connecting the inlet hose. This will prevent deposits of
sand or rust clogging the inlet hose filter.
Electrical connection
Before plugging the appliance into the wall socket,
make sure that:
1. the mains voltage corresponds to the voltage given
in the technical specifications;
2. the meter, fuses, mains power supply and wall
socket can all take the maximum load required.
Make sure that the socket and plug are compatible
without having to use any type of adapter. If necessary, have the domestic wiring system socket
replaced.
Safety standards require the appliance to be
earthed.
The Manufacturer accepts no liability for failure to
observe the above safety precautions.
PIN19GB
5
Loading...
+ 11 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.