Zanussi ZDW416 User Manual
INSTRUCTION BOOKLET
DISHWASHER
ZDW 416 FS
ZDW 416 BU
CONTENTS
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 4
Positioning, levelling, adjusting the worktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 4
Installing and securing the machine under a kitchen unit, fitting a decor panel on the door . . . . . . . . . .page 4
Fitting under acounter, securing under a counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 5
Water supply connections, water outlet connection, electrical connection . . . . . . . . . . . . . . . . . . . . . . . .page 6
Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 7
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 7
Use of rinse aid, use of detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 8
Loading the machine, use of the lower basket, use of the upper basket . . . . . . . . . . . . . . . . . . . . . . . . .page 9
Adjusting the height of the upper basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 10
Helpful hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 11
Washing programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 12
Operating sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 13
Maintenance and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 14
Cleaning the central filters, cleaning the large filter, internal and external cleaning . . . . . . . . . . . . . . . . .page 14
Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 15
TECHNICAL SPECIFICATIONS
ZDW 416 FS
DIMENSIONS Width cm 60 cm 59,6
Height with worktop cm 85
Height without worktop cm 82 cm 81,8 ÷ 87,8
Max depth cm 60 cm 55,5
Max depth with door open cm 120 cm 115
ELECTRICAL CONNECTION Voltage 220- 240 V/50Hz
MOTOR RATING DURING WASHING 200 W
POWER OF HEATING ELEMENT 1900 W
OVERALL POWER 2100 W
WATER SUPPLY PRESSURE minimum 5 N/cm
maximum 80 N/cm
ZDW 416 BU
2
2
CAPACITY (STANDARD IEC PLACE SETTINGS) 12
CONSUMPTION: Water 22 lt
Electricity 1.5 kW/h
PID10GB
2
WARNINGS
It is most important that this instruction book
should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move
house and leave the appliance, always ensure that
the book is left with the appliance in order that the
new owner can get to know the functioning of the
appliance and the relevant warnings.
These warnings are provided in the interest of
safety. You MUST read them carefully before
installing or using the appliance.
■ If the appliance is supplied with obvious damage,
consult the supplier before installing it.
■ Any plumbing work required to install this appliance
should be carried out by a qualified plumber or
competent person.
■ Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
■ This appliance is designed to be operated by adults.
■ Care must be taken to ensure that the appliance
does not stand on the electrical supply cable or on
the water inlet and drain hoses.
■ Under no circumstances should you attempt to
repair the machine yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning.
■ This appliance should be serviced only by an
authorised Zanussi Service Center.
■ Before disposing of the appliance, disconnect the
water hose, cut the electrical cable and ensure that
the door cannot close.
■ For proper disposal of the appliance, contact your
local waste collection service.
■ Zanussi dishwashers are designed to be used for
washing normal household utensils. Items that are
contaminated by petrol, paint, steel or iron debris,
corrosive, acidic or alkaline chemicals are not to be
washed in a dishwasher.
■ Under no circumstances should you open the door
whilst, the appliance is in operation. Always turn off
the appliance before opening the door.
However, the dishwasher features a special safety
device which cuts off the water inlet, should the door
be accidentally opened, thus avoiding water leaks.
■ Never touch the heating element during or
immediately after the end of the washing cycle.
■ When finishing loading or unloading close the door,
as an open door can be a hazard.
■ It is dangerous to lean or to sit on the dishwasher
door: the appliance could tip over.
■ Built-in dishwashers only: the appliance must be
secured to the underside of the worktop using the
brackets provided. Failure to do this could result in
an unstable appliance which may cause damage or
injury.
■ Unplug the appliance and turn off the water after
use.
PAV01GB
3
INSTALLATION
Remove all packaging before positioning the
machine.
Positioning (ZDW 416 FS)
If possible, position the machine next to a water tap
and a drain.
The sides and the back of the dishwasher can rest
against the adjacent furniture or the wall.
The dishwasher features fill and drain hoses which
can be turned either to the left or the right to suit the
installation.
Levelling (ZDW 416 FS)
Good levelling is essential for correct closure and
sealing of the door.
If the door does not close correctly, loosen or tighten
the adjustable support feet, until the machine is
perfectly level.
Installing and securing the machine under a
kitchen unit (ZDW 416 FS)
(sink-worktop unit)
By removing the machine's worktop, you can install it
under a close fitting sink unit or a pre-existing top, if
the dimensions of the recess correspond to those
shown in the picture.
Then proceed as follows:
Remove the machine worktop by unscrewing the two
front retaining screws, pull from the front and slide out
the rear slots, lifting the worktop.
Insert the machine after adjusting the height and levelling with the adjustable feet. When inserting the machine, ensure that the water inlet and drain hoses are
not kinked or squashed.
570÷600
820
600
IN01
Adjusting the worktop (ZDW 416 FS)
You can move the worktop forward or backward by 25
mm in order to align the machine with other kitchen
units.
Simply unscrew the two front retaining screws, move
the top to the required position and then retighten the
screws.
IN03
IN05
Caution
Once the machine has been installed, ensure that it
can be accessed easily for servicing.
Fitting a decor panel on the door
(ZDW 416 FS - ZDW 416 BU)
The door of this machine has frames for fitting a
plastic laminate decor panel in the colour required to
match the dishwasher with the rest of the kitchen
furniture. If you wish to do this you must provide the
panel yourself.
Width: 588 mm
Height: 586 mm
Max thickness: 4 mm
To fit the panel
Take the door frame off
after removing the retaining screws around the
edge.
Position the panel, refit
the frame and tighten the
retaining screws around
AP01
the edge.
Note:
The panel should be fitted before positioning the machine.
PIN24GB
4
Fitting under a counter (ZDW 416 BU)
(kitchen worktop or sink)
This dishwasher is designed to be fitted under a kitchen
counter or sink.
In either case, it is essential that the recess dimensions
indicated in the picture are followed.
Securing under a counter (ZDW 416 BU)
Open the door; vertically insert the two mounting
brakets (A) on the front part of the dishwasher and
turn them 90° (see figure).
Secure the brakets to the counter by means of two
3,5 x 16 screws provided.
No further openings for venting of the dishwasher are
required, but only to let the water fill and drain hoses
and power supply cable pass through.
600
596
max
820 ÷ 880
0 ÷ 60mm
II06
II28
818 ÷ 878
555
The recess height may be anywhere between 820
and 880 mm from the floor since the dishwasher
incorporates levelling feet adjustable over a wide
range (max 60 mm).
Adjust the height of the appliance by turning these
feet.
A distance of 2 mm should be allowed between the
top of the dishwasher and the counter top.
It is absolutely essential that the dishwasher is
disconnected from the electricity supply before gaining
access to any internal component.
90°
A
A
1
II18
2
Caution
Once the machine has been installed, ensure that it
can be accessed easily for servicing.
Fit the dishwasher into the appropriate housing space
and connect it. Make sure that the water fill and drain
hoses and the power supply cable are not bent or
kinked.
Adjust the height of the plinth by following the instructions shown in the figure.
IN10
PIN23GB
5
Loading...