Zanussi ZDT15006FA User Manual
EN
User manual 2
FR
Notice d'utilisation 14
Dishwasher
Lave-vaisselle
ZDT15006FA
Contents
Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2
Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4
Programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4
Options _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5
Before first use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6
Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8
Hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11
Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11
Technical information _ _ _ _ _ _ _ _ _ _ _ _ 13
Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ 13
Subject to change without notice.
Safety instructions
Before the installation and use of the appliance,
carefully read the supplied instructions. The
manufacturer is not responsible if an incorrect
installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference.
Children and vulnerable people safety
Warning! Risk of suffocation, injury or
permanent disability.
• Do not let persons, children included, with reduced physical sensory, reduced mental
functions or lack of experience and knowledge use the appliance. They must have supervision or instruction for the operation of
the appliance by a person who is responsible
for their safety.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep all detergents away from children.
• Keep children and pets away from the appliance door when it is open.
Installation
• Remove all the packaging.
• Do not install or use a damaged appliance.
• Do not install or use the appliance where the
temperature is less than 0 °C.
• Obey the installation instruction supplied with
the appliance.
• Make sure that the appliance is installed below and adjacent to safe structures.
Electrical connection
Warning! Risk of fire and electrical shock.
• The appliance must be earthed.
• Make sure that the electrical information on
the rating plate agrees with the power supply.
If not, contact an electrician.
• Always use a correctly installed shockproof
socket.
• Do not use multi-plug adapters and extension
cables.
• Make sure not to cause damage to the mains
plug and to the mains cable. Should the appliance power supply cable need to be replaced, this must be carried out by our Service Centre.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after
the installation.
• Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
• Do not touch the mains cable or the mains
plug with wet hands.
• Only for UK and Ireland. The appliance
has a 13 amp mains plug. If it is necessary to
change the fuse in the mains plug, use a 13
amp ASTA (BS 1362) fuse.
• This appliance complies with the E.E.C. Directives.
Water connection
• Make sure not to cause damage to the water
hoses.
• The appliance is to be connected to the water mains using the new supplied hose-sets.
Old hose sets must not be reused.
2
www.zanussi.com
• Before you connect the appliance to new
pipes or pipes not used for a long time, let
the water flow until it is clean.
• The first time you use the appliance, make
sure that there is no leakage.
Use
• This appliance is intended to be used in
household and similar applications such as:
– Staff kitchen areas in shops, offices and
other working environments
– Farm houses
– By clients in hotels, motels and other resi-
dential type environments
– Bed and breakfast type environments.
Warning! Risk of injury, burns, electrical
shock or fire.
• Do not change the specification of this appliance.
• Put knives and cutlery with sharp points in the
cutlery basket with the points down or in a
horizontal position.
• Do not keep the appliance door open without
supervision to prevent to fall on it.
• Do not sit or stand on the open door.
• Dishwasher detergents are dangerous. Obey
the safety instructions on the detergent packaging.
• Do not drink and play with the water in the
appliance.
• Do not remove the dishes from the appliance
until the programme is completed. There can
be detergent on the dishes.
• The appliance can release hot steam if you
open the door while a programme operates.
• Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
• Do not use water spray and steam to clean
the appliance.
Disposal
Warning! Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children
and pets to get closed in the appliance.
Service
• Contact the Service to repair the appliance.
We recommend only the use of original spare
parts.
• When you contact the Service, ensure that
you have the following information that is
available on the rating plate.
Model :
PNC :
Serial Number :
Product description
2
1
2
3
4
9
8
6
7
5
1
Lower spray arm
2
Filters
3
Rating plate
4
Rinse aid dispenser
5
Detergent dispenser
6
Salt container
7
Water hardness dial
8
Upper spray arm
9
Upper basket
3
www.zanussi.com
Control panel
1
3
4
2
CAB
5
1
On/off button
2
Programme buttons
3
Delay button
4
Indicators
5
Function buttons
Indicators Description
Salt indicator. This indicator is off while the programme operates.
Rinse aid indicator. This indicator is off while the programme operates.
End indicator.
Programmes
Programme
1)
Degree of soil
Type of load
Programme pha-
ses
Duration
(min)
Energy
(kWh)
Water
(l)
Heavy soil
Crockery, cutlery,
pots and pans
Prewash
Wash 70 °C
Rinses
Dry
90 - 100 1.7 - 1.9 19 - 21
Normal soil
Crockery and cutlery
Prewash
Wash 65 °C
Rinses
Dry
100 - 110 1.3 - 1.4 15 - 16
2)
Fresh soil
Crockery and cutlery
Wash 60 °C
Rinse
30 0.8 8
3)
Normal soil
Crockery and cutlery
Prewash
Wash 50 °C
Rinses
Dry
168 1.01 12.4
4
www.zanussi.com
Programme
1)
Degree of soil
Type of load
Programme pha-
ses
Duration
(min)
Energy
(kWh)
Water
(l)
4)
All Prewash 12 0.1 3
1) The water pressure and temperature, the variations of the mains supply, the options and the quantity of dishes
can change the programme duration and the consumption values.
2) With this programme you can wash a load with fresh soil. It gives good washing results in a short time.
3) This is the standard programme for test institutes. With this programme you have the most efficient use of
water and energy consumption for crockery and cutlery with normal soil. Refer to the supplied leaflet for test
information.
4) Use this programme to quickly rinse the dishes. This prevents the remaining food to bond on the dishes and
bad odours to come out from the appliance.
Do not use detergent with this programme.
Information for test institutes
For all the necessary information for test performance. send an email to:
info.test@dishwasher-production.com
Write down the product number (PNC) that is on the rating plate.
Options
Acoustic signals
The acoustic signals operate in these conditions:
• The programme is completed.
• The level of the water softener is adjusted
electronically.
• The appliance has a malfunction.
Factory setting: On.
It is possible to deactivate the acoustic sig-
nals.
How to deactivate the acoustic signals
1. Press the on/off button to activate the appli-
ance. Make sure that the appliance is in setting mode, refer to ‘Setting and starting a
programme’.
2. Press and hold function buttons (B) and (C)
at the same time until the indicators of function buttons (A), (B) and (C) start to flash.
3. Press function button (C),
• The indicators of function buttons (A) and
(B) go off.
• The indicator of function button (C) con-
tinues to flash.
• The end indicator comes on.
4. Press function button (C). The end indicator
goes off, the acoustic signals are deactivated.
5. Deactivate the appliance to confirm the setting.
How to activate the acoustic signals
1. Refer to ‘How to deactivate the acoustic
signals’, step (1) through (3).
2. Press function button (C),
• The indicators of function buttons (A) and
(B) go off.
• The indicator of function button (C) con-
tinues to flash.
• The end indicator is off.
3. Press function button (C). The end indicator
comes on, the acoustic signals are active.
4. Deactivate the appliance to confirm the setting.
5
www.zanussi.com
Before first use
1. Make sure that the set level of the water
softener agrees with the water hardness in
your area. If not, adjust the water softener.
Contact your local water authority to know
the water hardness in your area.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Processing residues can stay in the appliance. Start a programme to remove them.
Do not use detergent and do not load the
baskets.
Adjusting the water softener
Water hardness
Water softener
adjustment
German
degrees
(°dH)
French
degrees
(°fH)
mmol/l Clarke
degrees
Manual Elec-
tronic
47 - 50 84 - 90 8.4. - 9.0 58 - 63
2
1)
10
43 - 46 76 - 83 7.6 - 8.3 53 - 57
2
1)
9
37 - 42 65 - 75 6.5 - 7.5 46 - 52
2
1)
8
29 - 36 51 - 64 5.1 - 6.4 36 - 45
2
1)
7
23 - 28 40 - 50 4.0 - 5.0 28 - 35
2
1)
6
19 - 22 33 - 39 3.3 - 3.9 23 - 27
2
1)
5
1)
15 - 18 26 - 32 2.6 - 3.2 18 - 22 1 4
11 - 14 19 - 25 1.9 - 2.5 13 - 17 1 3
4 - 10 7 - 18 0.7 - 1.8 5 - 12 1 2
< 4 < 7 < 0.7 < 5
1
2)
1
2)
1) Factory position.
2) Do not use salt at this level.
You must adjust the water softener manually and electronically.
Manual adjustment
1
2
Turn the water hardness dial to the position 1 or 2.
6
www.zanussi.com
Electronic adjustment
1. Press the on/off button to activate the appliance. Make sure that the appliance is in setting mode, refer to ‘Setting and starting a
programme’.
2. Press and hold function buttons (B) and (C)
at the same time until the indicators of function buttons (A), (B) and (C) start to flash.
3. Press function button (A).
• The indicators of function buttons (B) and
(C) go off.
• The indicator of function button (A) con-
tinues to flash.
• Intermittent acoustic signals operate and
the end indicator flashes showing the current setting of the water softener.
– The number of flashes of the end indi-
cator and the number of the acoustic
signals show the level of the water softener.
E.g. 5 acoustic signals and 5 flashes +
pause + 5 acoustic signals and 5
flashes = level 5.
4. Press function button (A) again and again to
change the setting. Each time you press
function button (A) you go to the next level.
5. Deactivate the appliance to confirm the setting.
Filling the salt container
Caution! Water and salt can come out
from the salt container when you fill it. Risk
of corrosion. To prevent it, after you fill the salt
container, start a programme.
1
2
3
Put 1 litre of water in
the salt container (only for the first time).
4
5
6
Filling the rinse aid dispenser
1
2
max
M
A
X
1
2
3
4
+
3
4
7
www.zanussi.com
M
A
X
1
2
3
4
+
To adjust the released quantity of rinse aid,
turn the selector between position 1 (lowest
quantity) and position 4 (highest quantity).
Daily use
1. Open the water tap.
2. Press the on/off button to activate the appliance. Make sure that the appliance is in setting mode. Refer to ’SETTING AND STARTING A PROGRAMME’.
• If the salt indicator is on, fill the salt con-
tainer.
• If the rinse aid indicator is on, fill the rinse
aid dispenser.
3. Load the baskets.
4. Add the detergent.
5. Set and start the correct programme for the
type of load and soil.
Using the detergent
1
2
A
3
Put the detergent or
the tablet in compartment (A).
A
B
If the programme has
a prewash phase, put
a small quantity of detergent in compartment (B).
4
Combi detergent tablets
These tablets contain detergent, rinse aid and
other added agents. Be sure that these tablets
are applicable to the water hardness in your
area. Refer to the instructions on the packaging
of the products.
8
www.zanussi.com
When you use tablets, that contain salt and
rinse aid, do not fill the salt container and the
rinse aid dispenser. The rinse aid indicator always comes on if the rinse aid dispenser is
empty.
1. Adjust the water softener to the lowest level.
2. Set the rinse aid dispenser to the lowest position.
If you stop to use the combi detergent
tablets, before you start to use separately
detergent, rinse aid and dishwasher salt,
do these steps:
1. Press the on/off button to activate the appliance.
2. Set the water softener to the highest level.
3. Make sure that the salt container and the
rinse aid dispenser are full.
4. Start the shortest programme with a rinsing
phase, without detergent and without
dishes.
5. Adjust the water softener to the water hardness in your area.
6. Adjust the released quantity of rinse aid.
Setting and starting a programme
Setting mode
The appliance must be in setting mode to accept some operations.
The appliance is in setting mode when, after the
activation, all the programme indicators come
on.
If the control panel shows other conditions,
press and hold function buttons (B) and (C) at
the same time until the appliance is in setting
mode.
Starting a programme without delay start
1. Open the water tap.
2. Press the on/off button to activate the appliance. Make sure that the appliance is in setting mode.
3. Press the button of the programme you
want to set.
• The related programme indicator stays on.
• All the other programme indicators go off.
4. Close the appliance door. The programme
starts.
Starting a programme with delay start
1. Set the programme.
2. Press the delay button again and again until
the indicator of the number of hours you
want to set comes on. You can set 3, 6 or 9
hours.
• The delay indicator comes on.
3. Close the appliance door. The countdown
starts. When the countdown is completed,
the programme starts.
Opening the door while the appliance
operates
If you open the door, the appliance stops. When
you close the door, the appliance continues
from the point of interruption.
Cancelling the delay start
Press and hold function buttons (B) and (C) at
the same time until the delay indicator goes off
and all the programme indicators come on.
When you cancel a delay start, the appliance goes back to setting mode. You have
to set the programme again.
Cancelling the programme
Press and hold function buttons (B) and (C) at
the same time until all the programme indicators
come on.
Make sure that there is detergent in the detergent dispenser before you start a new
programme.
At the end of the programme
When the programme is completed, an intermittent acoustic signal operates and the end indicator comes on.
1. Press the on/off button to deactivate the appliance.
2. Close the water tap.
9
www.zanussi.com
Loading...