YOKOGAWA WU11 Instruction Manual

Page 1
1
Instruction Manual
Model WU11 Interconnection/Extension Cable for SENCOM® Products
1 GENERAL
1.1 INTRODUCTION
The WU11 interconnection and extension cable is specified for reliable transfer of digital signals between the SENCOM products and SA11 module and Yokogawa FLXA analyzer. (Suffix -V is for FU20F, FU24F, SC25F and IB100 / Suffix -S is for SENCOM SA11, BA11 and IB100). It is especially designed to be installed in a heavy industrial environment. The double shielded cable will protect the connected devices for interference from high voltages and currents which are present on other cables. The cable is specified to be used in IP67 applications, allowing it to be submerged as a whole. The cable has a wide temperature operation range which is sufficient for most of the applications. The materials used for the cable are flame retardant to resist the spread of fire. Depending on cable layout there is a choice of 8 different length to suit the customers needs.
1.2 Unpacking & Checking
Upon delivery, unpack the cable carefully and inspect it to ensure that it is not damaged during shipment. If damage is found, retain the original packing materials and immediately notify the carrier and the relevant local Yokogawa Sales office. Make sure the Model Code and Serial Number on the cable are the same as on the packing list.
1.3 Warranty & Service
Yokogawa products are guaranteed free from defects in workmanship and materials under normal use and service for a period of (typically) 12 months from the date of shipment from the manufacturer. Individual sales organizations can deviate from the typical warranty period, and the conditions of sale relating to the original purchase order should be consulted. Damage caused by wear and tear, inadequate maintenance, corrosion, or by the effects of chemical processes are excluded from this warranty coverage. In the event of a warranty claim, the defective goods should be sent (freight paid) to the Service Department of the relevant Yokogawa Sales office for repair or replacement (at Yokogawa’s discretion).
The following information must be included in the letter accompanying the returned goods:
• Model Code and Serial Number.
• Original Purchase Order and Date.
• Length of time in service and description of the process.
• Description of the fault and circumstances of the failure.
• Process/environmental conditions that may be related to the failure of the cable.
• Statement as to whether warranty or non-warranty service is requested.
• Complete shipping and billing instructions for return of material, plus the name and phone number of a contact person that can be reached for further information.
• Clean Statement
Returned goods that have been in contact with process fluids must be decontaminated and disinfected prior to shipment. Goods should carry a certificate to this effect, for the health and safety of our employees. Material Safety Data sheets must be included for all components of the process to which the cable is been exposed.
2 GENERAL SPECIFICATIONS
2.1 Description
Two twisted pair cables with overall shield, depending on the model: -oneside sensor connector with wire pin finishing for terminal connection. -oneside sensor connector with straight connector (extension). The cable is recognized by UL (fileno. E124763) and CSA (fileno. LL105324).
2.2 Cable materials
Twisted pair cables: Tinned copper wire, AGW24 (7/0.2 mm) Outside shield: Foil shield with drain wire, 125% coverage.
Braid, tinned copper with 95% coverage. Insulator: Polyethylene for the twisted pair cables.
Color twisted pair #1: green / yellow.
Color twisted pair #2: brown / white. Polyvinylchloride for the outside jacket,
solid extrusion, color black.
IM 12B06W02-03E-E
8th edition
Page 2
IM 12B06W02-03E-E
2
2.6 Dimensional drawing for suffix-V
Length (L) : 2, 3, 5, 10, 20, 30m
(6.6, 9.8, 16.4, 32.8,
65.6, 98.4 ft)
Dia. connector (D) : 10.6 ± 0.2 mm
(0.417 ± 0.008 inch)
Dia. cable (d) : 5.8 ± 0.1 mm
(0.228 ± 0.004 inch)
Wire pins : 8 x 1.3 mm
(0.31 x 0.05 inch)
2.7 Dimensional drawing for suffix-S
Length (L) : 1, 2, 3, 5, 10, 20, 30,
100m (3.3, 6.6, 9.8, 16.4,
32.8, 65.6, 98.4 328 ft)
Dia. connector (D) : 12.5 ± 0.2 mm
(0.471 ± 0.008 inch)
Dia. cable (d) : 5.8 ± 0.1 mm
(0.228 ± 0.004 inch)
Wire pins : 8 x 1.3 mm
(0.31 x 0.05 inch)
2.8 Cable installation
Procuring a smooth bend radius allows the cable to absorb the impact of bending and thereby increasing its life cycle.
Minimum bend radius is approx. 5 cm (2”). When using cable ties, do not pinch or deform the cable. When connected cable is subjected to any motion between two points, stress on the cable can be prevented by an adequate cable length or using a cable loop.
2.3 Connector materials
Housing : Polybutylene terephthalate
UL94V-0, color: black.
O-ring : Nitrilbutadieenrubber,
color: black. Nut : Brass. Contact finishing : Gold plated. Outer sleeve finishing : Polyvinylchloride
2.4 Electrical specifications
Twisted pair cables : Capacity < 50 pF/m
Resistance < 100 Ω/km Characteristic
Impedance < 120 Ω
Connector : Maximum rated current
5 A Maximum voltage 125 V
2.5 Operational specifications
Temperature : -20 ~ +85 °C
(-4 ~ +185 ºF)
Water Proof (CN) : IP67 (conform
IEC60529)
Figure 1. Dimensions
Page 3
IM 12B06W02-03E-E
3
4 MODEL AND SUFFIX CODES
Model Code Suffix Code Description
WU11 SENCOM cable Conn. type -M9 M9 female conn. for sensor connection Cable length -01 1 meter (only available with WP finishing with suffix -S)
-02 2 meter (only available with CN finishing)
-03 3 meter (only available with WP finishing)
-05 5 meter
-10 10 meter
-20 20 meter
-30 30 meter
-CC 100 meter* (only available with suffix -S) Finishing -WP Wire pin for terminal connection
-CN Straight connector M9 male Jacket material -V PVC only for FU20F,FU24F and SC25F
-S PVC, shielded connector(s) for SENCOM SA11, BA11
* Non-stock item, therefore long lead time.
Note: Suffix -V is for FU20F, FU24F, SC25F and IB100 Suffix -S is for SENCOM SA11, BA11 and IB100
3.1 Definition connector pin to cable
Pin # Twisted Wire Wire pair # color number
1 1 yellow 83 2 1 green 84 3 2 brown 87 4 drain black 82 5 2 white 86
3.2 Connection cable to FLXA analyzer
Signal Wire Wire FLXA Description color number terminal
Supply + brown 87 87 Supply Gnd white 86 86 Data + green 84 84 Data - yellow 83 83 Shield black 82 82
3 WIRING
Figure 2. Front view female connector
2 1
5
4
3
Page 4
IM 12B06W02-03-E-E
Subject to change without notice Printed in The Netherlands, 08-0918 Copyright ©
Yokogawa has an extensive sales and distribution network. Please refer to the European website (www.yokogawa.com/eu) to contact your nearest representative.
YPA EUROPE BV
Euroweg 2 3825 HD AMERSFOORT The Netherlands www.yokogawa.com/eu
YOKOGAWA ELECTRIC CORPORATION World Headquarters
9-32, Nakacho 2-chome, Musashino-shi Tokyo 180-8750 Japan www.yokogawa.com
YOKOGAWA CORPORATION OF AMERICA
2 Dart Road Newnan GA 30265 USA www.yokogawa.com/us
YOKOGAWA ELECTRIC ASIA Pte. LTD.
5 Bedok South Road Singapore 469270 Singapore www.yokogawa.com/sg
YOKOGAWA CHINA CO. LTD.
3F Tower D Cartelo Crocodile Building No.568 West Tianshan Road Changing District Shanghai, China www.yokogawa.com/cn
YOKOGAWA MIDDLE EAST B.S.C.(c)
P.O. Box 10070, Manama Building 577, Road 2516, Busaiteen 225 Muharraq, Bahrain www.yokogawa.com/bh
Loading...