yellow jacket SuperEvac 93511, SuperEvac 93515, SuperEvac 93596, SuperEvac 9356 series, SuperEvac 93598 Operation And Maintenance Manual

SuperEvac

Visit us at www.TestEquipmentDepot.com

®

Vacuum Pump

99 Washington Street
Melrose, MA 02176

Phone [phone]
Toll Free 1-800-517-8431

Models 93511 - 93516

93540 - 93598

shipping cap prior to use.

of motor.

Dual Voltage Motor Power Conversion (if applicable)

*Warranty is void if the set vacuum pump voltage does not match the power supply. Dual voltage

motors are factory set to 230V/50Hz.

8) Use a SuperEvac System I, II or
III to decrease
vacuum time by
over 50%. These
systems include
a 2-valve
vacuum mani­fold and two
3/8” vacuum hoses which can
evacuate three times faster than a
1/4” hose.

9) Use a heat gun ot the condenser
and evaporator to speed the evacua­tion process.

Built-in vacuum gauge:

The unique
built-in indicator gauge in
you pump monitors
evacuation progress
down to the 29-30”
range. If the reading stays
in the mid range, there is
either high contamination
or a large leak in the system.

If you think there is excessive moisture,
blow out the AC&R system with dry
nitrogen wherever possible. This reduces
the amount of contaminants that must be
“pulled” into the pump and increases
evacuation speed.

Use a nitrogen regulator
valve with pressure
limited to 150 psi, and a
frangible disc device set
at 175 PSIG.

When the indicator
reaches the 29-30” range,
turn on the electronic micron gauge for
more precise readings.

Oil Changes:

CHANGE OIL

AFTER EACH USAGE to protect

pump components from contaminants
pulled into pump during service. Place
used oil in a sealable container and
dispose properly in accordance with
local regulations.

STEP 1

Disconnect the
motor from the
power supply
and remove.
Remove the
yellow “CAU­TION” sticker
from the back of
the motor.

STEP 2

Pull up on the white plastic “arrow”
switch using needle-nosed pliers until
the switch is
loose inside the
motor housing (it
will not come
completely out of
the motor).

Note: Do not try
to turn or rotate
the switch until it has been pulled up and
is loose.

STEP 3

Point the arrow toward the desired
voltage setting and push the switch back
down into the
motor. The arrow
on the switch
should be sub-flush
of the motor
housing when
correctly installed
at the desired
voltage.
HI = 230 VAC / 50 Hz
LO = 115 VAC / 60 Hz

STEP 4

Replace the yellow
“CAUTION” sticker
over the voltage
selector switch.

Ensure that the
voltage setting
corresponds with the power supply that
the motor is plugged into.

93514
93516
93594

93515
93596
9356x

93511
9358x

9354x

(113 L/M) (311 L/M)(227 L/M)(170 L/M)

93541 93561 93581 93591

93590
93592
93593
93595
93598

93504

93365

Pump #

93514
93516
93594
9354x

Pump #

93515
93596
9356x

Pump #

93511
9358x

Pump #

93590
93592
93593
93595
93598

4 CFM 6 CFM 8 CFM 11 CFM

(113 L/M) (170 L/M) (227 L/M) (311 L/M)

Mounting body

8. Complete body (individual parts below) 93500 93500 93517 93517

9. Shaft seal 93031 93031 93031 93031

10. 30” vacuum gauge 93011 93011 93011 93011

11. Vacuum gauge crystal 93012 93012 93012 93012

12. Gas ballast with “O”-ring 93368 93368 93368 93368

13. “O”-ring for gas ballast/drain plug 93398 93398 93398 93398

14. 1/4” elbow tting 93028 93028 93028 93028

15. Intake ttings 93377 (3/8”)

16. Intake cap (1/4”) 93394 93394 93394 93394

17. Flare caps 93399 (3/8”)

18. Blank-of

19. Complete parts for blank-of

f valve with handle 93366 93366 93366 93366

f handle 93367 93367 93367 93367

40265 (Acme)

40284 (Acme)

93377 (3/8”)

40265 (Acme)

93399 (3/8”)

40284 (Acme)

93393 (1/2”)

40265 (Acme)

93395 (1/2”)

40284 (Acme)

93393 (1/2”)

40265 (Acme)

93395 (1/2”)

40284 (Acme)

Motor

20a. 1/2 hp - 115V / 60 Hz
(includes items 21, 22, 23a below)

20b. Export models: 1/2 hp - dual voltage
115V / 60 Hz, 230V / 50 Hz
(includes items 21 and 22)

21. 8/32 x 7-1/4” motor bolts (4) 93099 93099 93099 93099

22. Rocker style switch 931

23a. 8’ long US cord 93115 93115 93115 93115

23b. 8’ long EU cord (detachable IEC-320) 95431 95431 95431 95431

23c. 8’ long UK cord (detachable IEC-320) 95432 95432 95432 95432

93505 93505 93505 93505

93513 93513 93513 93513

17 93117 93117 93117

Final assembly parts

24. 8/32 x 5/8” socket head screws 93506 93506 93506 93506

25. Oil cover gasket 93507 93507 93507 93507

26. Drive coupling 93047 93047 93047 93047

27. Coupling spider 93050 93050 93050 93050

28. Right or left leg assembly with screws 93034 93034 93034 93034

Damaged supply cords must be replaced by special assemblies available from the manufacturer or its distributors.

9354x 9356x 9358x 9359x

28.3 lbs. (12.8 kg) 29.0 lbs. (13.1 kg) 30.3 lbs. (13.7 kg) 31.5 lbs. (14.3 kg)

2003-2017

Part #142993_K

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

TestEquipmentDepot.com