Yamaha YSP-5600 Reference Guide

B

Digital Sound Projector

Quick Reference Guide

SWK-W16

For more detailed information, refer to the Owner’s Manual on the
CD-ROM.

Caution: Do not attempt to play this CD-ROM in an audio player.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for

future reference.

2 Install this sound system in a well ventilated, cool, dry, clean place - away from direct sunlight,

heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following
minimum clearances.

Top: 5 cm, Rear: 5 cm, Sides: 5 cm

3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming

sounds.

4 Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit

in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal
injury.

5 Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be

exposed to liquid dripping or splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal

injury.

– Containers with liquid in them, as they may fall and liquid may cause electrical shock to the

user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat

radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or
personal injury.

7 Do not plug in this unit to a wall outlet until all connections are complete.

8 Do not operate this unit upside-down. It may overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this unit with a higher voltage than

specified is dangerous and may cause fire, damage to this unit, and/or personal injury. Yamaha will
not be held responsible for any damage resulting from use of this unit with a voltage other than
specified.

13 Be sure to connect to an appropriate outlet with a protective grounding connection. Improper

grounding can result in electrical shock, damage to the device(s), or even fire.

14 To prevent damage by lightning, keep the power cable and outdoor antennas disconnected from a

wall outlet or this unit during a lightning storm.

15 Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any

service is needed. The cabinet should never be opened for any reasons.

16 When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power

plug from the wall outlet.

17 Be sure to refer to the “Troubleshooting” section of the Owner’s Manual on the CD-ROM for

common operating errors before concluding that this unit is faulty.

18 Before moving this unit, press A to set it to standby mode and disconnect the AC power plug from

the wall outlet.

19 Condensation will form when the surrounding temperature changes suddenly. Disconnect the

power cable from the outlet, then leave this unit alone.

20 When using this unit for a long time, this unit may become warm. Turn the power off, then leave

this unit alone for cooling.

21 Install this unit near the AC outlet and where the AC power plug can be reached easily.

22 The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. When you

dispose of batteries, follow your regional regulations.

23 Excessive sound pressure from earphones and headphones can cause hearing loss.

24 Keep the product out of reach of children to avoid them swallowing small parts.

This unit is not disconnected from the AC power source as long as it is connected to the wall
outlet, even if this unit itself is turned off by A. This state is called the standby mode. In this
state, this unit is designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.

Do not use this unit within 22 cm of persons with a heart pacemaker implant or defibrillator
implant.

Radio waves may affect electro-medical devices.
Do not use this unit near medical devices or inside medical facilities.

The name plate for SWK-W16 is located on the bottom of the unit.

We, Yamaha Music Europe GmbH hereby declare that this unit is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.

Yamaha Music Europe GmbH

Siemensstr. 22-34 25462 Rellingen, Germany
Tel: [phone]

2 En

■ Notes on remote controls and batteries

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following conditions:
– places of high humidity, such as near a bath
– places of high temperatures, such as near a heater or stove
– places of extremely low temperatures
– dusty places

• Insert the battery according to the polarity markings (+ and -).

• Change all batteries if you notice the following conditions:
– the operation range of the remote control narrows

• If the batteries run out, immediately remove them from the remote control to prevent an explosion or
acid leak.

• If you find leaking batteries, discard the batteries immediately, taking care not to touch the leaked
material. If the leaked material comes into contact with your skin or gets into your eyes or mouth,
rinse it away immediately and consult a doctor. Clean the battery compartment thoroughly before
installing new batteries.

• Do not use old batteries together with new ones. This may shorten the life of the new batteries or
cause old batteries to leak.

• Do not use different types of batteries (such as alkaline and manganese batteries) together. Danger of
explosion may happen if batteries are incorrectly replaced. Specification of batteries may be different
even though they look the same.

• Before inserting new batteries, wipe the compartment clean.

• Keep batteries away from children. If a battery is accidentally swallowed, contact your doctor
immediately.

• When not planning to use the remote control for long periods of time, remove the batteries from the
remote control.

• Do not charge or disassemble the supplied batteries.

Information for Users on Collection and Disposal of Old
Equipment and Used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that
used electrical and electronic products and batteries should not be mixed with general
household waste.
For proper treatment, recovery and recycling of old products and used batteries, please
take them to applicable collection points, in accordance with your national legislation
and the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries,
please contact your local municipality, your waste disposal service or the point of sale
where you purchased the items.

[Information on Disposal in other Countries outside the European
Union]

These symbols are only valid in the European Union. If you wish to discard these items,
please contact your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it
complies with the requirement set by the Directive for the chemical involved.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it
should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions
described below.

Note

The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is
hazardous if engaged in a live socket outlet.

■ Special Instructions for U.K. Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE
FOLLOWING CODE:

Blue: NEUTRAL
Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the
letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth terminal of the three pin plug.

To view the Owner’s Manual, click on “English” in the screen displayed automatically when you
insert the CD-ROM into your PC, or click on the model name if the screen to select models is
displayed, and then click on “English” in the next screen. Then, follow the onscreen instructions.
If the screen is not displayed automatically, open the “index.html” in the CD-ROM.
The Owner’s Manual contained in the CD-ROM can be downloaded from the following website:
URL : http://download.yamaha.com/

En 3

About this Quick Reference Guide

Battery × 2
(AAA, R03, UM-4)

Press down on the arrow
and slide the cover in the
direction in which it
points.

Slide the cover back to close it.

Within 6 m

The Quick Reference Guide provides instructions for connecting a TV and BD/DVD
player to the unit, applying settings, and playing content. For more information on
operations, refer to the Owner’s Manual in the supplied CD-ROM.

Read the safety instructions described in this booklet before using the unit. For
instructions on how to operate or set the external devices, refer to documentation
supplied with each device.

• indicates supplementary explanations for better use.

• indicates precautions for use of the unit and its feature limitations.

Supplied accessories

Before connecting, make sure you have received all of the following items.

Remote control Batteries

Power cable (2 m)* IntelliBeam microphone

Stands (x2) Screws (For the stands; x2) Subwoofer cable (3 m)

System control cable

(3 m)

* The shape of the power cable plug varies depending on where the unit was

purchased.

Devices and cables required for connection

• TV • BD/DVD player • HDMI cables (x2)

(AAA, R03, UM-4) (x2)

Cardboard microphone

(6 m)

• Owner’s Manual CD-ROM

• Quick Reference Guide (this booklet)

• MusicCast Setup Guide

Preparing remote control

Before installing batteries or using the remote control, be sure to read battery and
remote control precautions in this booklet.

Optical cable (1.5 m)

Installing the batteries

stand

Operation range

4 En Supplied accessories

1

Height channel audio is output in a diagonal
direction upward and forward from the unit. As
height channel sound beams are reflected off the
ceiling, sound can be heard from above.

2

Depending upon the rack, table-top stand, or floor
stand used, the stands may not be necessary.

• Install the unit in the center of the left and right
walls.

• This unit can be mounted on a wall. See page 17
in the Owner’s Manual.

• The listening position (such as sofa, etc.) should be

located at the front of the unit.

• The distance between the listening position and the

unit should be more than 1.8 m.

• Set the listening position as far from the back wall as

possible (the optimal listening position is halfway
between the unit and the back wall, or slightly closer
to the back wall).

• To achieve desired surround sound effects, be
sure that obstacles such as furniture may not
obstruct the path of sound beams (p. 6).

• Be sure that the unit installed with at least 5 cm
of empty space above and below it.

• Leaving as much space as possible in a
diagonal direction in front of, and above, the
unit when installing it.

1

• Attach the supplied stands to the unit if it will
be installed on a rack

2

(p. 7).

1 2 3 4

a Installation

This unit reflects sound beams off of walls and a ceiling to create the surround sound effect. The position of this unit in relation to the listening position, walls, and a ceiling is important
to achieving the desired surround sound effects. Refer to pages 5 to 7 when installing the unit. When installing this unit on a rack behind which there is limited space, for example, it
may be easier to connect external devices to this unit first. This will depend upon the installation location. See page 8 for information regarding the connection of external devices.

Notes

• Be sure to install this unit on a large, stable stand where it does not fall subject to vibrations, such as from an earthquake, and where it is out of the reach of children.

• There is a built-in antenna on the top of the unit. Do not install it on a metal rack, and do not stack metal items on top of the unit.

• The unit’s speakers are not magnetically shielded. Do not install hard disk drives or similar devices near the unit.

• Do not stack the unit directly on top of other playback devices, or vice versa. Heat and vibrations may result in damage or malfunction.

Recommended place for installation

a Installation En 5

Objects,
such as
furniture

Viewed from above Viewed from the side

Sound beams
are reflected off
the ceiling

Sound beam output varies depending upon the 3D surround/Surround setting (pages 38
and 39 in the Owner’s Manual) and the channel output setting (page 73 in the Owner’s
Manual). The illustration above shows the path of sound beams when 3D surround is
enabled and “Front” in the Channel Out setting is set to “Beam”.

Parallel installation

40° to 50°

Objects, such as
furniture

Viewed from above Viewed from the side

The illustrations above show the path of sound beams when 3D surround is enabled
(page 38 in the Owner’s Manual) and “Front” in the Channel Out setting is set to “Stereo”.
(page 73 in the Owner’s Manual).

Sound beams
are reflected off
the ceiling

Coner installation

1 2 3 4

Example for installing the unit

This unit outputs sound beam as shown in the illustrations below. Install this unit where there are no obstacles such as furniture obstructing the path of sound beams. Otherwise, the
desired surround sound effects may not be achieved.

If the unit is installed so that it is parallel to a wall, install it as close to the exact center of the wall as possible.

If the unit is installed in a corner of a room, position it at a 40–50° angle to the adjacent walls.

• See pages 14 to 16 in the Owner’s Manual for additional installation examples.

6 En a Installation