Yamaha XW-CS-700 User Manual

XW-CS-700

Wireless extension microphone kit

for the Yamaha CS-700

Congratulations on your purchase of the XW-CS-700, a wireless extension microphone kit for the Yamaha CS-700. The
XW-CS-700 allows additional microphone pick-up in a room without having to wire the room with audio cables, allowing
for a clean extension of the microphone capture of the Yamaha CS-700.

Please read the safety documentation for the components that are part of the XW-CS-700 kit carefully and follow their
instructions.

The components in this kit will require to be prepared before first use. Please follow the set-up instructions as provided
in this document.

1 2 3

Components

The XW-CS-700 kit includes the following components. Please check that you received all of them:
1 Revolabs™ HD dual™: The HD dual includes the Receiver for the wireless microphone, the Charger to charge up

to two microphones, and the required power adapters.

1 Revolabs HD™ omni-directional wireless microphone.

1 Proprietary audio cable to connect the HD dual Receiver to the CS-700.

1 User guide (this document).

Preparing the wireless Receiver

Before enabling the wireless extension microphone with the CS-700, the wireless Receiver needs to be configured and a
connection between the wireless extension microphone and the Receiver needs to be created.

Charging the microphones

First, please charge the microphone battery for at least an hour to ensure that enough charge is in the battery to go
through the process. To charge, connect the Charger to the main powers using one of the provided 5VDC AC Adapters
and using an appropriate power outlet 110-240 AC, 50-60Hz. The power LED on the Charger will illuminate. Place the
microphone in the Charger and ensure that it is seated well in the charging bay. Either a solid red LED (charging) or solid
green LED (100% charged) light will appear to confirm that the microphone is inserted properly. While in the Charger, the
microphones are not transmitting audio to the Receiver. In normal use, batteries should fully charge in about 2 hours, but
will “quick-charge” to 80% capacity in approximately 1 hour and 20 minutes. Fully charged microphones left in the Charger
remain solid green. Before first use of the microphone it should be charged for several hours or until the LED on the
microphone turns green in the Charger.

Whenever microphones are not in use, they should be inserted into the Charger. It is important to ensure that all
microphones are inserted fully so that charging will occur. Features of the Charger are shown in the following image.

1. LED indicator — power status indicator

2. Charger Bays — charges up to 2 Microphones

3. Power Cord Receptacle — power supply input, 5 VDC (on rear)

Important: The Serial Number of the Microphones used with the XW-CS-700 should start with a 7010 or 8020.
Serial numbers starting with numbers different than 7010 or 8020 are not approved to be used with the CS-700
extension microphone kit! In the supported microphones the Lithium Polymer rechargeable batteries that
power the microphones are field replaceable. Replace the batteries only with the manufacturer and model
battery type recommended by Yamaha Unified Communications. Please contact Yamaha Unified
Communications (uc.yamaha.com) for correct manufacturer approved and recommended replacement type
batteries.

Caution: Risk of explosion if batteries are mishandled or replaced by an incorrect type. Do not disassemble
batteries or attempt to charge outside the system. Do not dispose of batteries in fire. Dispose of batteries in
accordance with manufacturer’s instructions and local regulations.

Pairing the wireless microphone to the Receiver

Pairing creates a link between the wireless microphone and the Receiver, with a unique identifier. This process only needs
to be done once. Afterwards the microphone will automatically try to connect to the same Receiver whenever it is lifted
from the Charger or otherwise switched on.

Receiver front view

Rear View

(1) Channel LED indicators: Displays microphone status and pairing state, Channel 1 and 2
(2) Pairing Push Buttons: For pairing microphones to the Receiver, Channel 1 and 2
(3) Power-in Receptacle (5 V DC)
(4) 3.5mm Balanced Input Connectors
(5) 3.5mm Balanced Output Connectors
(6) Mini-USB Serial Interface for firmware upgrades and management
(7) Configuration DIP

To pair the microphone to the Receiver:

1. Turn the microphone OFF (no LED activity). If the microphone is ON, press and hold the Mute button for 10

seconds until the LED turns solid red then release the button to turn the unit off. (do not release the button when
you hear two beeps).

2. Place the microphone unit into pairing mode by holding the button down for seven seconds. The LED will first turn

green, then solid red. Release the button once the LED is red. The microphone is now in pairing mode.

3. Within one minute, push and hold the button for channel one on the Receiver for seven seconds until the LED

turns solid red, then release. The LED for that channel will be solid red until the microphone and the Receiver have
a wireless handshake to create the pairing, as indicated by a quick green flash. Please note that the pairing might
take a minute or longer to occur. Once the connection is established both the microphone and the Receiver LED
will turn to flashing red. To activate the microphone press the mute button once, the LEDs will switch colors to
blinking green.

1 2 3 4 5 6 7

Mute button