Yamaha WR450 FY 2009 Owner's manual

Read this manual carefully before operating this vehicle.Read this manual carefully before operating this vehicle.

20092009

OWNER’S SERVICE MANUALOWNER’S SERVICE MANUAL

WR450F(Y)WR450F(Y)

5TJ-28199-46-E05TJ-28199-46-E0

WR450F(Y)

OWNER'S SERVICE MANUAL

permission of Yamaha Motor Co., Ltd.

is expressly prohibited.

Printed in Japan

FOREWORD

INTRODUCTION

Congratulations on your purchase of a Yamaha WR series. This model is the culmination of Yamaha's vast experience in the production of pacesetting racing machines. It represents the highest grade of craftsmanship and reliability that have made Yamaha a leader. This manual explains operation, inspection, basic maintenance and tuning of your machine. If you have any questions about this manual or your machine, please contact your Yamaha dealer.

For Canada The design and manufacture of this Yamaha machine fully comply with the emissions standards for clean air applicable at the date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the machine. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the recommended maintenance schedules and operating instructions contained within this manual.

Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your machine and this manual. If you have any questions concerning this manual, please consult your Yamaha dealer.

PLEASE READ THIS MANUAL CAREFULLY AND COMPLETELY BEFORE OPERATING THIS MACHINE. DO NOT ATTEMPT TO OPERATE THIS MACHINE UNTIL YOU HAVE ATTAINED A SATISFACTORY KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURES AND UNTIL YOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES. REGULAR INSPECTIONS AND CAREFUL MAINTENANCE, ALONG WITH GOOD RIDING SKILLS, WILL ENSURE THAT YOU SAFETY ENJOY THE CAPABILITIES AND THE RELIABILITY OF THIS MACHINE.

IMPORTANT MANUAL INFORMATION

Particularly important information is distinguished in this manual by the following notations.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

A WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

A NOTICE indicates special precautions that must be taken to avoid damage to the vehicle or other property.

A TIP provides key information to make procedures easier or clearer.

SAFETY INFORMATION

For Canada This machine is designed for off-road use only. It is illegal for this machine to be operated on any public street, road, or highway. Off-road use on public lands may be illegal. Please check local regulations before riding.

Except for Canada THIS MACHINE IS DESIGNED STRICTLY FOR COMPETITION USE, ONLY ON A CLOSED COURSE. It is illegal for this machine to be operated on any public street, road, or highway. Off-road use on public lands may also be illegal. Please check local regulations before riding.

• THIS MACHINE IS TO BE OPERATED BY AN EXPERIENCED RIDER ONLY. Do not attempt to operate this machine at maximum power until you are totally familiar with its characteristics.

• THIS MACHINE IS DESIGNED TO BE RIDDEN BY THE OPERATOR ONLY. Do not carry passengers on this machine.

• ALWAYS WEAR PROTECTIVE APPAREL. When operating this machine, always wear an approved helmet with goggles or a face shield. Also we ar heavy boots, gloves, and protective clothing. Always wear proper fitting clothing that will not be caught in any of the moving parts or controls of the machine.

• ALWAYS MAINTAIN YOUR MACHINE IN PROPER WORKING ORDER. For safety and reliability, the machine must be properly maintained. Always perform the pre-operation checks indicated in this manual. Correcting a mechanical problem before you ride may prevent an accident.

• GASOLINE IS HIGHLY FLAMMABLE. Always turn off the engine while refueling. Take care to not spill any gasoline on the engine or exhaust system. Never refuel in the vicinity of an open flame, or while smoking.

• GASOLINE CAN CAUSE INJURY. If you should swallow some gasoline, inhale excess gasoline vapors, or allow any gasoline to get into your eyes, contact a doctor immediately. If any gasoline spills onto your skin or clothing, immediately wash skin areas with soap and water, and change your clothes.

• ONLY OPERATE THE MACHINE IN AN AREA WITH ADEQUATE VENTILATION. Never start the engine or let it run for any length of time in an enclosed area. Exhaust fumes are poisonous. These fumes contain carbon monoxide, which by itself is odorless and colorless. Carbon monoxide is a dangerous gas which can cause unconsciousness or can be lethal.

• PARK THE MACHINE CAREFULLY; TURN OFF THE ENGINE. Always turn off the engine if you are going to leave the machine. Do not park the machine on a slope or soft ground as it may fall over.

• THE ENGINE, EXHAUST PIPE, MUFFLER, AND OIL TANK WILL BE VERY HOT AFTER THE ENGINE HAS BEEN RUN. Be careful not to touch them or to allow any clothing item to contact them during inspection or repair.

• PROPERLY SECURE THE MACHINE BEFORE TRANSPORTING IT. When transporting the machine in another vehicle, always be sure it is properly secured and in an upright position and that the fuel cock is in the "OFF" position. Otherwise, fuel may leak out of the carburetor or fuel tank.

F.I.M. MACHINE WEIGHTS (Except for Canada)

Weights of machines without fuel

The minimum weights for motocross machines are:

for the class 125 cc: minimum 88 kg (194 lb)

for the class 250 cc: minimum 98 kg (216 lb)

for the class 500 cc: minimum 102 kg (225 lb)

In modifying your machine (e.g., for weight reduction), take note of the above limits of weight.

HOW TO USE THIS MANUAL

FINDING THE REQUIRED PAGE

1. This manual consists of seven

chapters; "General Information", "Specifications", "Regular inspection and adjustments", "Tuning", "Engine", "Chassis" and "Electrical".

2. The table of contents is at the be-

ginning of the manual. Look over the general layout of the book before finding then required chapter and item. Bend the book at its edge, as shown, to find the required fore edge symbol mark and go to a page for required item and description.

MANUAL FORMAT

All of the procedures in this manual are organized in a sequential, stepby-step format. The information has been complied to provide the mechanic with an easy to read, handy reference that contains comprehensive explanations of all disassembly, repair, assembly, and inspection operations. In this revised format, the condition of a faulty component will precede an arrow symbol and the course of action required will follow the symbol, e.g.,

•Bearings Pitting/damage→ Replace.

HOW TO READ DESCRIPTIONS

To help identify parts and clarify procedure steps, there are exploded diagrams at the start of each removal and disassembly section.

1. An easy-to-see exploded diagram "1" is provided for removal and disassembly jobs.

2. Numbers "2" are given in the order of the jobs in the exploded diagram. A number that is enclosed by a circle indicates a disassembly step.

3. An explanation of jobs and notes is presented in an easy-to-read way by the use of symbol marks "3". The meanings of the symbol marks are given on the next page.

4. A job instruction chart "4" accompanies the exploded diagram, providing the order of jobs, names of parts, notes in jobs, etc.

5. For jobs requiring more information, the step-by-step format supplements "5" are given in addition to the exploded diagram and job instruction chart.

ILLUSTRATED SYMBOLS (Refer to the illustration)

Illustrated symbols "1" to "7" are used to identify the specifications appearing in the text.

1. With engine mounted

2. Filling fluid

3. Lubricant

4. Special tool

5. Tightening

6. Specified value, Service limit

7. Resistance (Ω), Voltage (V), Electric current (A)

Illustrated symbols "8" to "13" in the exploded diagrams indicate grade of lubricant and location of lubrication point.

8. Apply engine oil

9. Apply molybdenum disulfide oil

10. Apply brake fluid

11. Apply lightweight lithium-soap base grease

12. Apply molybdenum disulfide grease

13. Apply silicone grease

Illustrated symbols "14" to "15" in the exploded diagrams indicate where to apply a locking agent and where to install new parts.

14. Apply locking agent (LOC-

15. Use new one

TITE

)

TABLE OF CONTENTS

GENERAL INFORMATION

SPECIFICATIONS REGULAR INSPECTION AND

ADJUSTMENTS TUNING

ENGINE

1 2 3 4 5

CHASSIS

ELECTRICAL

6 7

CONTENTS

CHAPTER 1

GENERAL INFOR-

MATION

DESCRIPTION ................. 1-1

MACHINE

IDENTIFICATION.............1-2

INCLUDED PARTS..........1-2

IMPORTANT

INFORMATION.................1-2

CHECKING OF

CONNECTION..................1-3

SPECIAL TOOLS.............1-4

CONTROL FUNCTIONS..1-8 MULTI-FUNCTION

DISPLAY ..........................1-9

STARTING AND

BREAK-IN ......................1-14

TORQUE-CHECK

POINTS...........................1-16

CLEANING AND

STORAGE......................1-17

CHAPTER 2

SPECIFICATIONS

GENERAL

SPECIFICATIONS............2-1

MAINTENANCE

SPECIFICATIONS............2-3

TIGHTENING TORQUES..2-12 LUBRICATION

DIAGRAMS ....................2-18

CABLE ROUTING

DIAGRAM.......................2-20

CHAPTER 3

REGULAR INSPEC-

TION AND AD-

JUSTMENTS

PERIODIC MAINTENANCE CHART FOR THE EMISSION CONTROL SYSTEM

(For Canada)....................3-1

GENERAL MAINTENANCE AND LUBRICATION CHART

(For Canada)....................3-2

MAINTENANCE INTERVALS FOR

COMPETITION USE.........3-3

PRE-OPERATION INSPECTION AND

MAINTENANCE................3-7

ENGINE ............................3-8

CHASSIS........................3-19

ELECTRICAL .................3-29

CHAPTER 4

TUNING

ENGINE

(Except for Canada)........4-1

CHASSIS..........................4-5

CHAPTER 5

ENGINE

RADIATOR.......................5-1

CARBURETOR.................5-4

AIR INDICTOIN

SYSTEM .........................5-13

CAMSHAFTS..................5-15

CYLINDER HEAD...........5-20

VALVES AND VALVE

SPRINGS........................5-23

CYLINDER AND

PISTON...........................5-27

CLUTCH .........................5-30

OIL FILTER ELEMENT

AND WATER PUMP.......5-34

BALANCER ....................5-38

OIL PUMP.......................5-40

KICK SHAFT AND

SHIFT SHAFT.................5-43

AC MAGNETO AND

STARTER CLUTCH........5-48

ENGINE REMOVAL........5-53

CRANKCASE AND

CRANKSHAFT ...............5-57

TRANSMISSION, SHIFT CAM AND SHIFT FORK.5-63

CHAPTER 6

CHASSIS

FRONT WHEEL AND

REAR WHEEL ..................6-1

FRONT BRAKE AND

REAR BRAKE ..................6-6

FRONT FORK.................6-16

HANDLEBAR..................6-23

STEERING......................6-27

SWINGARM....................6-31

REAR SHOCK

ABSORBER.................... 6-36

CHAPTER 7

ELECTRICAL

ELECTRICAL COMPONENTS AND

WIRING DIAGRAM...........7-2

IGNITION SYSTEM...........7-4

ELECTRIC STARTING

SYSTEM............................7-6

CHARGING SYSTEM.....7-14

THROTTLE POSITION

SENSOR SYSTEM .........7-16

LIGHTING SYSTEM .......7-19

SIGNALING SYSTEM.....7-21

GENERAL INFORMATION

DESCRIPTION

1. Clutch lever

2. Hot starter lever

3. Engine stop switch

4. Multi-function display

5. Main switch

6. Start switch

7. Front brake lever

8. Throttle grip

9. Radiator cap

10. Fuel tank cap

11. Taillight

12. Kickstarter crank

13. Fuel tank

• The machine you have purchased may differ slightly from those shown in the following.

• Designs and specifications are subject to change without notice.

14. Headlight

15. Radiator

16. Coolant drain bolt

17. Rear brake pedal

18. Valve joint

19. Fuel cock

20. Cold starter knob

21. Air cleaner

22. Catch tank

23. Drive chain

24. Shift pedal

25. Oil dipstick

26. Front fork

1-1

MACHINE IDENTIFICATION

There are two significant reasons for knowing the serial number of your machine:

1. When ordering parts, you can give the number to your Yamaha dealer for positive identification of the model you own.

2. If your machine is stolen, the authorities will need the number to search for and identify your machine.

VEHICLE IDENTIFICATION NUMBER

The vehicle identification number "1" is stamped on the right of the steering head pipe.

ENGINE SERIAL NUMBER

The engine serial number "1" is stamped into the elevated part of the right-side of the engine.

SPARK PLUG WRENCH

This spark plug wrench "1" is used to remove and install the spark plug.

NIPPLE WRENCH

This nipple wrench "1" is used to tighten the spoke.

IMPORTANT INFORMATION

PREPARATION FOR REMOVAL AND DISASSEMBLY

1. Remove all dirt, mud, dust, and foreign material before removal and disassembly.

• When washing the machine with high pressured water, cover the parts follows. Silencer exhaust port Side cover air intake port Water pump housing hole at the bottom Drain hole on the cylinder head (right side) All electrical components

MODEL LABEL

The model label "1" is affixed to the frame under the rider's seat. This information will be needed to order spare parts.

INCLUDED PARTS

VALVE JOINT

This valve joint "1" prevents fuel from flowing out and is installed to the fuel tank breather hose.

JET NEEDLE PULL-UP TOOL (Except for Canada)

The jet needle pull-up tool "1" is used to pull the jet needle out of the carburetor.

DRIVE CHAIN SPROCKET GUIDE (For EUROPE)

Use the drive chain sprocket guide "1" when installing the included drive sprockt (13T).

2. Use proper tools and cleaning equipment. Refer to "SPECIAL TOOLS" section.

3. When disassembling the machine, keep mated parts together. They include gears, cylinders, pistons, and other mated parts that have been "mated" through normal wear. Mated parts must be reused as an assembly or replaced.

In this installation, make sure the arrow faces the fuel tank and also downward.

1-2

CHECKING OF CONNECTION

4. During the machine disassembly, clean all parts and place them in trays in the order of disassembly. This will speed up assembly time and help assure that all parts are correctly reinstalled.

5. Keep away from fire.

ALL REPLACEMENT PARTS

1. We recommend to use Yamaha genuine parts for all replacements. Use oil and/or grease recommended by Yamaha for assembly and adjustment.

GASKETS, OIL SEALS AND ORINGS

1. All gaskets, oil seals, and O-rings should be replaced when an engine is overhauled. All gasket surfaces, oil seal lips, and O-rings must be cleaned.

2. Properly oil all mating parts and bearings during reassembly. Apply grease to the oil seal lips.

LOCK WASHERS/PLATES AND COTTER PINS

1. All lock washers/plates "1" and cotter pins must be replaced when they are removed. Lock tab(s) should be bent along the bolt or nut flat(s) after the bolt or nut has been properly tightened.

BEARINGS AND OIL SEALS

1. Install the bearing(s) "1" and oil seal(s) "2" with their manufacturer's marks or numbers facing outward. (In other words, the stamped letters must be on the side exposed to view.) When installing oil seal(s), apply a light coating of lightweight lithium base grease to the seal lip(s). Oil the bearings liberally when installing.

Do not use compressed air to spin the bearings dry. This causes damage to the bearing surfaces.

CIRCLIPS

1. All circlips should be inspected carefully before reassembly. Always replace piston pin clips after one use. Replace distorted circlips. When installing a circlip "1", make sure that the sharp-edged corner "2" is positioned opposite to the thrust "3" it receives. See the sectional view.

2. Dry each terminal with an air blower.

3. Connect and disconnect the connector two or three times.

4. Pull the lead to check that it will not come off.

5. If the terminal comes off, bend up the pin "1" and reinsert the terminal into the connector.

6. Connect:

• Connector

The two connectors "click" together.

7. Check for continuity with a tester.

• If there in no continuity, clean the

terminals.

• Be sure to perform the steps 1 to 7

listed above when checking the wire harness.

• For a field remedy, use a contact re-

vitalizer available on the market.

• Use the tester on the connector as

shown.

CHECKING OF CONNECTION

Dealing with stains, rust, moisture, etc. on the connector.

1. Disconnect:

• Connector

1-3

SPECIAL TOOLS

The proper special tools are necessary for complet e and accurate tune-up and assembly. Using the correct special tool will help prevent damage caused by the use of improper tools or improvised techniques. The shape and part number used for the special tool differ by country, so two types are provided. Refer to the list provided to avoid errors when placing an order.

• For U.S.A. and Canada, use part number starting with "YM-", "YU-" or "ACC-".

• For others, use part number starting with "90890-".

Tool name/Part number How to use Illustration

Dial gauge and stand YU-3097, 90890-01252 Stand YU-1256

These tools are used to check each part for runout or bent.

Crankshaft installing tool Crankshaft installing pot YU-90050, 90890-01274 Crankshaft installing bolt YU-90050, 90890-01275 Spacer (crankshaft installer) YM-91044, 90890-04081 Adapter (M12) YU-90063, 90890-01278

Piston pin puller set YU-1304, 90890-01304

Radiator cap tester YU-24460-01, 90890-01325 Radiator cap tester adapter YU-33984, 90890-01352

These tools are used to install the crankshaft.

This tool is used to remove the piston pin.

These tools are used for checking the cooling system.

Steering nut wrench YU-33975, 90890-01403

This tool is used when tighten the steering ring nut to specification.

1-4

SPECIAL TOOLS

Tool name/Part number How to use Illustration

Damper rod holder YM-01494, 90890-01494

Use this tool to remove and install the damper rod.

Fork seal driver YM-A0948, 90890-01502

Spoke nipple wrench YM-01521, 90980-01521

Sheave holder YS-1880-A, 90890-01701

This tool is used when install the fork oil seal.

This tool is used to tighten the spoke.

This tool is used for when loosening or tightening the flywheel magneto securing nut.

Pocket tester YU-3112-C, 90890-03112

Timing light YM-33277-A, 90890-03141

Use this tool to inspect the coil resistance, output voltage and amperage.

This tool is necessary for checking ignition timing.

1-5

SPECIAL TOOLS

Tool name/Part number How to use Illustration

Valve spring compressor YM-4019, 90890-04019

This tool is needed to remove and install the valve assemblies.

Clutch holding tool YM-91042, 90890-04086

Valve guide remover Intake 4.5 mm (0.18 in) Exhaust 5.0 mm (0.20 in) YM-4116, 90890-04116 YM-4097, 90890-04097

Valve guide installer Intake 4.5 mm (0.18 in) Exhaust 5.0 mm (0.20 in) YM-4117, 90890-04117 YM-4098, 90890-04098

Valve guide reamer Intake 4.5 mm (0.18 in) Exhaust 5.0 mm (0.20 in) YM-4118, 90890-04118 YM-4099, 90890-04099

This tool is used to hold the clutch when removing or installing the clutch boss securing nut.

This tool is needed to remove and install the valve guide.

This tool is needed to install the valve guide.

This tool is needed to rebore the new valve guide.

Rotor puller YM-4142, 90890-04142

Crankcase separating tool YU-A9642 90890-04152

This tool is used to remove the flywheel magneto.

These tool is used to remove the crankshaft from either case.

1-6

SPECIAL TOOLS

Tool name/Part number How to use Illustration

Dynamic spark tester YM-34487 Ignition checker 90890-06754

This instrument is necessary for checking the ignition system components.

Vacuum/pressure pump gauge set YB-35956-A, 90890-06756

Digital tachometer YU-39951-B, 90890-06760

YAMAHA Bond No. 1215 (ThreeBond® No. 1215) 90890-85505

This tool is used to check the air induction system.

This tool is needed for observing engine rpm.

This sealant (Bond) is used for crankcase mating surface, etc.

1-7

CONTROL FUNCTIONS

MAIN SWITCH

Functions of the respective switch positions are as follows: ON: The engine can be started only at this position. OFF: All electrical circuits are switched off.

Main switch indicator light

The main switch "1" is equipped with an indicator light "2" to avoid forgetting to turn it off. This light functions as follows.

• It lights up with the main switch "ON".

• It goes out when the engine increases its speed after being started.

• It lights up again when the engine is stopped.

If the indicator light will not light up with the main switch "ON", it shows a lack of the battery voltage. Recharge the battery.

CLUTCH LEVER

The clutch lever "1" is located on the left handlebar; it disengages or engages the clutch. Pull the clutch lever to the handlebar to disengage the clutch, and release the lever to engage the clutch. The lever should be pulled rapidly and released slowly for smooth starts.

SHIFT PEDAL

The gear ratios of the constant-mesh 5 speed transmission are ideally spaced. The gears can be shifted by using the shift pedal "1" on the left side of the engine.

FRONT BRAKE LEVER

The front brake lever "1" is located on the right handlebar. Pull it toward the handlebar to activate the front brake.

REAR BRAKE PEDAL

The rear brake pedal "1" is located on the right side of the machine. Press down on the brake pedal to activate the rear brake.

ENGINE STOP SWITCH

The engine stop switch "1" is located on the left handlebar. Continue pushing the engine stop switch till the engine comes to a stop.

START SWITCH

The start switch "1" is located on the right handlebar. Push this switch to crank the engine with the starter.

KICKSTARTER CRANK

Rotate the kickstarter crank "1" away from the engine. Push the starter down lightly with your foot until the gears engage, then kick smoothly and forcefully to start the engine. This model has a primary kickstarter crank so the engine can be started in any gear if the clutch is disengaged. In normal practices, however, shift to neutral before starting.

THROTTLE GRIP

The throttle grip "1" is located on the right handlebar; it accelerates or decelerates the engine. For acceleration, turn the grip toward you; for deceleration, turn it away from you.

FUEL COCK

The fuel cock supplies fuel from the tank to carburetor and also filters the fuel. The fuel cock has the three positions: OFF: With the lever in this position, fuel will not flow. Always return the lever to this position when the engine is not running. ON: With the lever in this position, fuel flows to the carburetor. Normal riding is done with the lever in this position. RES: With the lever in this position fuel flows to the carburetor from the reserve section of the fuel tank after the main supply of the fuel has been depleted. Normal riding is possible with the lever is in this position, but it is recommended to add fuel as soon as possible.

1-8

MULTI-FUNCTION DISPLAY

COLD STARTER KNOB

When cold, the engine requires a richer air-fuel mixture for starting. A separate starter circuit, which is controlled by the cold starter knob "1", supplies this mixture. Pull the cold starter knob out to open the circuit for starting. When the engine has warmed up, push it in to close the circuit.

HOT STARTER LEVER

The hot starter lever "1" is used when starting a warm engine. Use the hot starter lever when starting the engine again immediately after it was stopped (the engine is still warm). Pulling the hot starter lever injects secondary air to thin the air-fuel mixture temporarily, allowing the engine to be started more easily.

MULTI-FUNCTION DISPLAY

Be sure to stop the machine before making any setting changes to the multi-function display.

The multi-function display is equipped with the following: BASIC MODE:

• Speedometer

•Clock

• Two tripmeters (which shows the distance that has been traveled since it was last set to zero)

RACE MODE:

• Timer (which shows the time that has been accumulated since the start of timer measurement)

• Tripmeter (which shows the accumulated travel distance in timer measurement)

• Change tripmeter digits (capable of change to any given ones)

DESCRIPTION Operation buttons:

1. Select button "SLCT 1"

2. Select button "SLCT 2"

3. Reset button "RST"

Screen display:

4. Tripmeter indicator

5. Tripmeter indicator

6. Timer indicator

7. Clock/Timer

8. Speedometer

9. Odometer/Tripmeter

BASIC MODE Changing speedometer display (for U.K.)

1. Push the "SLCT2" button for 2 seconds or more to change the speedometer units. The speedometer display will change in the following order: MPH → km/h → MPH.

Setting the time

1. Push the "SLCT1" button for 2 seconds or more to enter the time setting mode.

2. Push the "RST" button to change the display for time indication. The display will change in the following order: Hour→ Minute→ Second→ Hour.

The digits capable of setting go on flashing.

SIDESTAND

This sidestand "1" is used to support only the machine when standing or transporting it.

• Never apply additional force to the sidestand.

• Hold up the sidestand before starting out.

The operation buttons can be pushed in the following two manners: Short push: Push the button. ( ) Long push: Push the button for 2 seconds or more. ( )

3. Push the "SLCT1" button (plus) or "SLCT2" button (minus) and change the time. A long push on the button will fast-forward the time.

4. To end the setting, push the "RST" button for 2 seconds or more.

• In a 30-second absence of button

operation, the setting will come to an end with the indicated time.

• To reset the seconds, push the

"SLCT1" button or "SLCT2" button.

1-9

MULTI-FUNCTION DISPLAY

Changing odometer and tripmeter A/B (TRIP A/B)

1. Push the "SLCT2" button to change the tripmeter display. The display will change in the following order: Odometer → TRIP A→ TRIP B→ TRIP A → Odometer.

To reset the digits, select the tripmeter involved and push the "RST" button for 2 seconds or more.

Returning to BASIC MODE from RACE MODE

It is possible to return to BASIC MODE with timer measurement at a stop.

1. Check that the timer is not in operation. If the timer is in operation, stop the timer by pushing the "SLCT1" button and "SLCT2" button at the same time.

RACE MODE Putting measurement on standby

Starting measurement consists of the following two starts, either of which can be selected.

• Manual start Starting measurement by the rider himself operating the button. (A long push on the "SLCT2" button will put measurement on standby.)

• Auto start Starting timer measuremen t automatically on detection of the movement of the machine. (A long push on the "SLCT1" button will put measurement on standby.)

Manual start

Initial setting at changeover to RACE MODE will remain for manual start.

1. Check that changeover to RACE MODE has been made. (Refer to "Changeover from BASIC MODE to RACE MODE".)

CHANGEOVER TO BASIC MODE/ RACE MODE

• Measurement using the timer function can be made in RACE MODE.

• Indicator will light up as an identifier that shows RACE MODE has been selected.

• RACE MODE cannot display the functions as in BASIC MODE.

• Changeover to RACE MODE forces the digits for tripmeter A (TRIP A) in BASIC MODE to be reset.

Changeover from BASIC MODE to RACE MODE

1. Push the "SLCT1" button and

"SLCT2" button for 2 seconds or more at the same time to change over to RACE MODE.

Changeover to RACE MODE will put manual start measurement on standby causing and to flash. (For manual start, refer to "Putting measurement on standby" in "RACE MODE".)

2. Push the "SLCT1" button and "SLCT2" button for 2 seconds or more at the same time to change over to BASIC MODE.

When the machine is made ready for a run by manual start, and will start flashing.

2. Start timer measurement by pushing the "RST" button.

3. When stopping timer measurement, pushing the "SLCT1" button and "SLCT2" button at the same time.

If the machine is run while timer measurement is not made, no change will occur to the digit in tripmeter A (TRIP A).

4. To resume the measurement, again push the "SLCT1" button and "SLCT2" button at the same time.

1-10

MULTI-FUNCTION DISPLAY

Auto start

1. Check that changeover has been made to RACE MODE. (Refer to "Changeover from BASIC MODE to RACE MODE".)

2. Make the machine ready for a run by pushing the "SLCT1" button for 2 seconds or more.

When the measurement is made ready for a run by auto start, and

will start flashing. Timer display

will turn on scrolling from left to right.

3. Run the machine and start timer measurement.

4. To stop timer measurement, pushing the "SLCT1" button and "SLCT2" button at the same time.

Resetting measurement data

Resetting can be made in the following two manners. Resetting is possible while timer measurement is made:

• Reset tripmeter A. Resetting is possible while timer measurement is not made:

• Reset tripmeter A and timer. Resetting tripmeter A (TRIP A)

1. Check that the timer is in operation. If the timer is not in operation, start the timer by pushing the "SLCT1" button and "SLCT2" button at the same time.

2. Reset tripmeter A (TRIP A) display by pushing the "RST" button for 2 seconds or more.

If reset, and travel distance display will go on flashing for four seconds.

Correcting tripmeter A (TRIP A)

1. Change the travel distance display by pushing the "SLCT1" button (plus) or "SLCT2" button (minus). A long push on the button will fast-forward the change.

Change can be made any time while timer measurement is or is not being made.

If the machine is run while timer measurement is not made, no change will occur to the digit in tripmeter A (TRIP A).

5. To resume the measurement, again pushing the "SLCT1" button and "SLCT2" button at the same time.

Resetting tripmeter A (TRIP A) and timer

1. Check that the timer is not in operation. If the timer is in operation, stop it by pushing the "SLCT1" button and "SLCT2" button at the same time.

2. Reset all measured data by pushing the "RST" button for 2 seconds or more.

• Resetting will reset the timer display

and travel distance display and put measurement on standby.

• Auto start attempt will put measure-

ment on standby as such. Likewise, manual start attempt will put measurement on standby as such.

1-11

FUNCTION DIAGRAM

BASIC MODE

A short push on the button changes the operation in the arrowed direction.

A short push on the button changes the operation in both arrowed directions.

A long push on the button changes the operation in the arrowed direction.

A long push on the button changes the operation in both arrowed directions.

Clock

MULTI-FUNCTION DISPLAY

Meter function Function that can be performed whether

the time is or is not in operation.

Extent to which the meter can operate

RACE MODE

Tripmeter

ODO TRIP A TRIP B

ODO

Putting measurement on standby

Manual start

Timer in operation

Reset TRIP A

Correct TRIP A

Speedometer (for U.K.)

km/h MPH

MPH

Auto start

Measurement starts as the machine moves

Timer not in operation

Correct TRIP A

Reset TRIP A & timer

1-12

The following diagram illustrates the multi-function display regarding the direction and operation condition involved in each of its functions.

A. A short push on the button

changes the operation in the arrowed direction.

B. A short push on the button

changes the operation in both arrowed directions.

C. A long push on the button

changes the operation in the arrowed direction.

D. A long push on the button

changes the operation in both

arrowed directions. E. Meter function F. Function that can be performed

whether the time is or is not in

operation. G. Extent to which the meter can

operate

MULTI-FUNCTION DISPLAY

1. BASIC MODE

2. Clock

3. Trip meter

4. Speedometer (for U.K.)

5. RACE MODE

6. Putting measurement on standby

7. Manual start

8. Auto start

9. Measurement starts as the machine moves

10. Timer in operation

11. Reset TRIP A

12. Correct TRIP A

13. Timer not in operation

14. Reset TRIP A & timer

1-13

STARTING AND BREAK-IN

FUEL

Always use the recommended fuel as stated below. Also, be sure to use new gasoline.

Recommended fuel:

Premium unleaded gasoline only with a research octane number of 95 or higher.

Use only unleaded gasoline. The use of leaded gasoline will cause severe damage to the engine internal parts such as valves, piston rings, and exhaust system, etc.

If knocking or pinging occurs, use a different brand of gasoline or higher octane grade.

• For refueling, be sure to stop the engine and use enough care not to spill any fuel. Also be sure to avoid refueling close to a fire.

• Refuel after the engine, exhaust pipe, etc. have cooled off.

Gasohol (For Canada)

There are two types of gasohol: gasohol containing ethanol and that containing methanol. Gasohol containing ethanol can be used if the ethanol content does not exceed 10%. Gasohol containing methanol is not recommended by Yamaha because it can cause damage to the fuel system or vehicle performance problems.

HANDLING NOTE

• Unlike a two-stroke engine, this engine cannot be kick started when the throttle is open because the kickstarter may kick back. Also, if the throttle is open the air/fuel mixture may be too lean for the engine to start.

• Before starting the machine, per form the checks in the pre-operation check list.

AIR FILTER MAINTENANCE

According to "CLEANING THE AIR FILTER ELEMENT" section in the CHAPTER 3, apply the foam -air-filter oil or its equivalent to the element. (Excess oil in the element may adversely affect engine starting.)

STARTING A COLD ENGINE

This model is equipped with an ignition circuit cut-off system. The engine can be started under the following conditions.

• When the transmission is in neutral.

• When the clutch is disengaged with the transmission in any position. However, it is recommended to shift into neutral before starting the engine.

1. Inspect the coolant level.

2. Turn the fuel cock to "ON".

3. Push on the main switch to "ON".

4. Shift the transmission into neutral.

5. Fully open the cold starter knob

"1".

• If the starter motor will not turn when pushing the start switch, stop pushing it immediately and kick start the engine in order to avoid the load on the motor.

• Do not open the throttle while kicking the kickstarter crank. Otherwise, the kickstarter crank may kick back.

7. Return the cold starter knob to its

original position and run the engine at 3,000–5,000 r/min for 1 or 2 minutes.

Since this model is equipped with an accelerator pump, if the engine is raced (the throttle opened and closed), the air/fuel mixture will be too rich and the engine may stall. Also unlike a two-stroke engine, this model can idle.

Do not warm up the engine for extended periods of time.

STARTING A WARM ENGINE

Do not operate the cold starter knob and throttle. Pull the hot starter lever "1" and start the engine by pushing the start switch or by kicking the kickstarter crank forcefully with a firm stroke. As soon as the engine starts, Release the hot starter lever to close the air passage.

Never start or run the engine in a closed area. The exhaust fume s are poisonous; they can cause loss of consciousness and death in a very short time. Always operate the machine in a well-ventilated area.

• The carburetor on this machine has a built-in accelerator pump. Therefore, when starting the engine, do not operate the throttle or the spark plug will foul.

6. Start the engine by pushing the start switch or by kicking the kickstarter crank.

If the engine fails to start by pushing the start switch, release the switch, wait a few seconds, and then try again. Each starting attempt should be as short as possible to preserve the battery. Do not crank the engine more than 10 seconds on any one attempt. If the engine does not start with the starter motor, try using the kickstarter crank.

1-14

Restarting an engine after a fall

Pull the hot starter lever and start the engine. As soon as the engine starts, Release the hot starter lever to close the air passage.

STARTING AND BREAK-IN

The engine fails to start

Pull the hot starter lever all the way out and while holding the lever, kick the kickstarter crank 10 to 20 times to clear the engine. Then, restart the engine. Refer to "Restarting an engine after a fall".

Thro

ttle

Cold

Hot

grip

start-

op-

er le-

era-

knob

ver

tion*

Air temperature = less than 5 °C (41 °F)

St ar

Air tempera-

ture = more

than 5 °C (41

°F)

a c

Air tempera-

ture (normal

temperature)

= between 5

°C (41 °F)

and 25 °C

(77 °F)

Air temperature = more than 25 °C (77 °F)

Starting an engine after a long period of time

Restarting a warm engine

Restarting an engine after a fall

* Operate the throttle grip before kick starting.

Ope

n 3

or 4

ON OFF

time

Non

ON OFF

NoneON/

OFF

Non

OFF OFF

Non

ON OFF

Non

OFF ON

Non

OFF ON

OFF

BREAK-IN PROCEDURES

1. Before starting the engine, fill the fuel tank with the fuel.

2. Perform the pre-operation checks on the machine.

3. Start and warm up the engine. Check the idle speed, and check the operation of the controls and the engine stop switch. Then, restart the engine and check its operation within no more than 5 minutes after it is restarted.

4. Operate the machine in the lower gears at moderate throttle openings for five to eight minutes.

5. Check how the engine runs when the machine is ridden with the throttle 1/4 to 1/2 open (low to medium speed) for about one hour.

6. Restart the engine and check the operation of the machine throughout its entire operating range. Restart the machine and operate it for about 10 to 15 more minutes.

After the break-in or before each ride, you must check the entire machine for loose fittings and fasteners as per "TORQUE-CHECK POINTS". Tighten all such fasteners as required.

Observe the following break-in procedures during initial operation to ensure optimum performance and avoid engine damage.

1-15

TORQUE-CHECK POINTS

Frame construction Frame to rear frame

Combined seat and fuel tank Fuel tank to frame Exhaust system Silencer to rear frame Engine mounting Frame to engine

Engine bracket to engine Engine bracket to frame

Steering Steering stem to handlebar Steering stem to frame

Steering stem to upper bracket Upper bracket to handlebar

Suspension Front Steering stem to front fork Front fork to upper bracket

Front fork to lower bracket

Rear For link type Assembly of links

Link to frame Link to rear shock absorber

Link to swingarm Installation of rear shock absorber Rear shock absorber to frame Installation of swingarm Tightening of pivot shaft

Wheel Installation of wheel Front Tightening of wheel axle

Tightening of axle holder

Rear Tightening of wheel axle

Wheel to rear wheel sprocket

Brake Front Brake caliper to front fork

Brake disc to wheel

Tightening of union bolt

Brake master cylinder to handlebar

Tightening of bleed screw

Tightening of brake hose holder

Rear Brake pedal to frame

Brake disc to wheel

Tightening of union bolt

Brake master cylinder to frame

Tightening of bleed screw

Tightening of brake hose holder

Fuel system Fuel tank to fuel cock Lubrication system Tightening of oil hose clamp

Concerning the tightening torque, refer to "TIGHTENING TORQUES" section in the CHAPTER 2.

1-16

CLEANING AND STORAGE

CLEANING

Frequent cleaning of your machine will enhance its appearance, maintain good overall performance, and extend the life of many components.

1. Before washing the machine, block off the end of the exhaust pipe to prevent water from entering. A plastic bag secured with a rubber band may be used for this purpose.

2. If the engine is excessively greasy, apply some degreaser to it with a paint brush. Do not apply degreaser to the chain, sprockets, or wheel axles.

3. Rinse the dirt and degreaser off with a garden hose; use only enough pressure to do the job.

Excessive hose pressure may cause water seepage and contamination of wheel bearings, front forks, brakes and transmission seals. Many expensive repair bills have resulted from improper high pressure detergent applications such as those available in coin-operated car washers.

4. After the majority of the dirt has been hosed off, wash all surfaces with warm water and a mild detergent. Use an old toothbrush to clean hard-to-reach places.

5. Rinse the machine off immediately with clean water, and dry all surfaces with a soft towel or cloth.

6. Immediately after washing, remove excess water from the chain with a paper towel and lubricate the chain to prevent rust.

7. Clean the seat with a vinyl upholstery cleaner to keep the cover pliable and glossy.

8. Automotive wax may be applied to all painted or chromed surfaces. Avoid combination cleanerwaxes, as they may contain abrasives.

9. After completing the above, start the engine and allow it to idle for several minutes.

STORAGE

If your machine is to be stored for 6 0 days or more, some preventive measures must be taken to avoid deterioration. After cleaning the machine thoroughly, prepare it for storage as follows:

1. Drain the fuel tank, fuel lines, and the carburetor float bowl.

2. Remove the spark plug, pour a tablespoon of SAE 10W-30 motor oil in the spark plug hole, and reinstall the plug. With the engine stop switch pushed in, kick the engine over several times to coat the cylinder walls with oil.

3. Remove the drive chain, clean it thoroughly with solvent, and lubricate it. Reinstall the chain or store it in a plastic bag tied to the frame.

4. Lubricate all control cables.

5. Block the frame up to raise the wheels off the ground.

6. Tie a plastic bag over the exhaust pipe outlet to prevent moisture from entering.

7. If the machine is to be stored in a humid or salt-air environment, coat all exposed metal surfaces with a film of light oil. Do not apply oil to rubber parts or the seat cover.

Make any necessary repairs before the machine is stored.

1-17

GENERAL SPECIFICATIONS

SPECIFICATIONS

GENERAL SPECIFICATIONS

Model name: WR450FY (USA, CDN, AUS, NZ)

WR450F (EUROPE, ZA)

Model code number: 5TJN (USA)

5TJP (CDN) 5TJR (EUROPE) 5TJS (AUS, NZ, ZA)

Dimensions: USA, CDN, ZA EUROPE AUS, NZ

Overall length 2,175 mm (85.63

in) Overall width 825 mm (32.48 in) ←← Overall height 1,295 mm (50.98

in) Seat height 980 mm (38.58 in) 990 mm (38.98 in) ← Wheelbase 1,485 mm (58.46

in) Minimum ground clearance 365 mm (14.37 in) 375 mm (14.76 in) 370 mm (14.57 in)

Dry weight:

Without oil and fuel 112.5 kg (248.0 lb)

Engine:

Engine type Liquid cooled 4-stroke, DOHC Cylinder arrangement Single cylinder, forward inclined

Displacement 449 cm Bore × stroke 95 .0 × 63.4 mm (3.74 × 2.50 in) Compression ratio 12.3 : 1 Starting system Kick and electric starter

Lubrication system: Dry sump Oil type or grade:

Engine oil (For USA and CDN)

Yamalube 4, SAE10W-40 or SAE20W-50

Yamalube 4-R, SAE10W-50

API service SG type or higher,

JASO standard MA

(15.8 Imp oz, 15.2 US oz)

2,200 mm (86.61 in)

1,305 mm (51.38 in)

1,500 mm (59.06 in)

2,190 mm (86.22 in)

1,300 mm (51.18 in)

1,485 mm (58.46 in)

2-1

GENERAL SPECIFICATIONS

(Except for USA and CDN)

SAE10W-30, SAE10W-40, SAE15W-40,

SAE20W-40 or SAE20W-50

API service SG type or higher,

JASO standard MA

Oil capacity:

Engine oil

Periodic oil change 0.95 L (0.84 Imp qt, 1.00 US qt) With oil filter replacement 1.0 L (0.88 Imp qt, 1.06 US qt)

Total amount 1.2 L (1.06 Imp qt, 1.27 US qt) Coolant capacity (including all routes): 1.0 L (0.88 Imp qt, 1.06 US qt) Air filter: Wet type element Fuel:

Type Premium unleaded gasoline only with a research octane

number of 95 or higher. Tank capacity 8.0 L (1.76 Imp gal, 2.11 US gal) Reserve 1.1 L (0.24 Imp gal, 0.29 US gal)

Carburetor:

Type FCR-MX39 Manufacturer KEIHIN

Spark plug:

Type/manufacturer CR8E/NGK (resistance type) Gap 0.7–0.8 mm (0.028–0.031 in)

Clutch type: Wet, multiple-disc Transmission: USA, CDN, AUS, NZ, ZA EUROPE

Primary reduction system Gear ← Primary reduction ratio 61/23 (2.652) ← Secondary reduction system Chain drive ← Secondary reduction ratio 50/13 (3.846) 47/14(3.357) Transmission type Constant mesh, 5-speed ← Operation Left foot operation ← Gear ratio:

1st 29/12 (2.417) ← 2nd 26/15 (1.733) ← 3rd 21/16 (1.313) ← 4th 21/20 (1.050) ← 5th 21/25 (0.840) ←

Chassis: USA, CDN, ZA EUROPE AUS, NZ

Frame type Semi double cra-

dle Caster angle 27.3 ° 26.8 ° 27.0 ° Trail 117 mm (4.61 in) 115 mm (4.53 in) 116 mm (4.57 in)

←←

2-2

MAINTENANCE SPECIFICATIONS

Tire:

Type With tube Size (front) 80/100-21 51M (USA, CDN, ZA)

90/90-21 54R (EUROPE, AUS, NZ) Size (rear) 110/100-18 64M (USA, CDN, ZA)

130/90-18 69R (EUROPE, AUS, NZ)

Tire pressure (front and rear) 100 kPa (1.0 kgf/cm

Brake:

Front brake type Single disc brake Operation Right hand operation Rear brake type Single disc brake Operation Right foot operation

Suspension:

Front suspension Telescopic fork Rear suspension Swingarm (link type monocross suspension)

Shock absorber:

Front shock absorber Coil spring/oil damper Rear shock absorber Coil spring/gas, oil damper

Wheel travel:

Front wheel travel 300 mm (11.8 in) Rear wheel travel 305 mm (12.0 in)

Electrical:

Ignition system CDI Generator system AC magneto Battery type YTZ7S (F) Battery voltage/capacity 12V/6 AH Specific gravity 1.310

Headlight type: Quartz bulb (halogen) Bulb wattage × quantity:

Headlight 12 V 35/36.5 W × 1 Taillight 12 V 1.6/0.3 W × 1

MAINTENANCE SPECIFICATIONS

ENGINE

, 15 psi)

Item Standard Limit

Cylinder head:

Warp limit ---- 0.05 mm (0.002

in)

Cylinder:

Bore size 95.00–95.01 mm (3.7402–3.7406 in) ---Out of round limit ---- 0.05 mm (0.002

in)

2-3

MAINTENANCE SPECIFICATIONS

Item Standard Limit

Camshaft:

Drive method Chain drive (Left) ---Camshaft cap inside diameter 22.000–22.021 mm (0.8661–0.8670 in) ---Camshaft outside diameter 21.959–21.972 mm (0.8645–0.8650 in) ---Shaft-to-cap clearance 0.028–0.062 mm (0.0011–0.0024 in) 0.08 mm (0.003

in)

Cam dimensions

Intake "A" 30.100–30.200 mm (1.1850–1.1890 in) 30.000 mm

(1.1811 in)

Intake "B" 22.450–22.550 mm (0.8839–0.8878 in) 22.350 mm

(0.8799 in)

Exhaust "A" 30.200–30.300 mm (1.1890–1.1929 in) 30.100 mm

(1.1850 in)

Exhaust "B" 22.450–22.550 mm (0.8839–0.8878 in) 22.350 mm

(0.8799 in)

Camshaft runout limit ---- 0.03 mm

(0.0012 in)

Timing chain:

Timing chain type/No. of links 98XRH2010-118M/118 ---Timing chain adjustment method Automatic ----

Valve, valve seat, valve guide:

Valve clearance (cold)

IN 0.10–0.15 mm (0.0039–0.0059 in) ---EX 0.20–0.25 mm (0.0079–0.0098 in) ----

Valve dimensions:

"A" head diameter (IN) 26.9–27.1 mm (1.0591–1.0669 in) ---"A" head diameter (EX) 27.9–28.1 mm (1.0984–1.1063 in) ----

2-4

MAINTENANCE SPECIFICATIONS

Item Standard Limit "B" face width (IN) 2.26 mm (0.089 in) ---"B" face width (EX) 2.26 mm (0.089 in) ----

"C" seat width (IN) 0.9–1.1 mm (0.0354–0.0433 in) 1.6 mm (0.0630

in)

"C" seat width (EX) 0.9–1.1 mm (0.0354–0.0433 in) 1.6 mm (0.0630

in)

"D" margin thickness (IN) 1 mm (0.0394 in) 0.85 mm (0.033

in)

"D" margin thickness (EX) 1 mm (0.0394 in) 0.85 mm (0.033

in)

Stem outside diameter (IN) 4.475–4.490 mm (0.1762–0.1768 in) 4.445 mm

(0.1750 in)

Stem outside diameter (EX) 4.965–4.980 mm (0.1955–0.1961 in) 4.935 mm

(0.1943 in)

Guide inside diameter (IN) 4.500–4.512 mm (0.1772–0.1776 in) 4.550 mm

(0.1791 in)

Guide inside diameter (EX) 5.000–5.012 mm (0.1969–0.1973 in) 5.050 mm

(0.1988 in)

Stem-to-guide clearance (IN) 0.010–0.037 mm (0.0004–0.0015 in) 0.08 mm (0.003

in)

Stem-to-guide clearance (EX) 0.020–0.047 mm (0.0008–0.0019 in) 0.10 mm (0.004

in)

Stem runout limit ---- 0.01 mm

(0.0004 in)

Valve spring:

Free length (IN) 39.46 mm (1.55 in) 38.46 mm (1.51

in)

Free length (EX) 37.61 mm (1.48 in) 36.61 mm (1.44

in)

2-5

+ 194 hidden pages