Yamaha TYROS Installation Guide

TOOLS for TYROS

Installation Guide/Installationsanleitung/Manuel d’installation

SPECIAL NOTICES

• The software and this Installation Guide are exclusive copyrights of Yamaha Corporation.

• Use of the software and this guide is governed by the SOFTWARE LICENSING AGREEMENT which the purchaser fully agrees to upon breaking the seal of the software packaging. (Please read carefully the AGREEMENT at the end of this guide before installing the application.)

• Copying of the software or reproduction of this guide in whole or in part by any means is expressly forbidden without the written consent of the manufacturer.

• Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this guide and the software.

• Copying of the commercially available music data is strictly prohibited except for your personal use.

• The company names and product names in this Installation Guide are the trademarks or registered trademarks of their respective companies.

• Future upgrades of application and system software and any changes in speciﬁcations and functions will be announced separately.

BESONDERE HINWEISE

• Dieses Programm und diese Installationsanleitung sind im Sinne des Urheberrechts alleiniges Eigentum der Yamaha Corporation.

• Die Benutzung des Programms und dieser Anleitung unterliegt der SOFTWARE-LIZENZVEREINBARUNG, mit der sich der Erwerber durch Öffnen des Siegels der Programmverpackung uneingeschränkt einverstanden erklärt. (Bitte lesen Sie die VEREINBARUNG am Ende dieser Anleitung vor Installation der Anwendung sorgfältig durch.)

• Das Kopieren der Software und die Reproduktion dieser Anleitung, in welcher Form auch immer, in Teilen oder als Ganzes, sind nur mit schriftlicher Genehmigung des Herstellers erlaubt und sonst ausdrücklich verboten.

• Yamaha leistet keinerlei Garantie hinsichtlich der Benutzung des Programms und der zugehörigen Dokumentation und übernimmt keine Verantwortung für die Ergebnisse der Benutzung dieser Anleitung oder des Programms.

• Das Kopieren im Handel erhältlicher Musikdaten ist nur für Ihren Privatgebrauch zulässig und sonst streng untersagt.

• Die in dieser Installationsanleitung erwähnten Firmen- und Produktnamen sind Warenzeichen bzw. eingetragene Warenzeichen der betreffenden Firmen.

• Zukünftige Aktualisierungen von Anwendungs- und Systemsoftware sowie jede Anderung der technischen Daten und Funktionen werden separat bekanntgegeben.

REMARQUES PARTICULIERES

• Les droits d’auteurs (copyright) de ce logiciel et de ce manuel d’installation appartiennent exclusivement à Yamaha Corporation.

• L’usage de ce logiciel et de ce manuel est déﬁni par l’accord de licence auquel l’acheteur déclare souscrire sans réserve lorsqu’il ouvre le sceau de l’emballage du logiciel. (Veuillez donc lire attentivement l’accord de licence du logiciel situé à la ﬁn de ce manuel avant d’installer le logiciel.)

• Toute copie du logiciel et toute reproduction totale ou partielle de ce manuel, par quel moyen que ce soit, est expressément interdite sans l’autorisation écrite du fabricant.

• Yamaha n’offre aucune garantie en ce qui concerne l’utilisation du logiciel et de la documentation. Yamaha ne peut en aucun cas être tenu responsable des dommages éventuels résultant de l’utilisation de ce manuel et de ce logiciel.

• Toute copie de données musicales commercialisées est formellement interdite, sauf pour usage personnel.

• Les noms des ﬁrmes et des produits apparaissant dans ce manuel d’installation sont des marques commerciales ou des marques déposées appartenant à leurs détenteurs respectifs.

• Les remises à jour du programme et du système ainsi que toute modiﬁcation des caractéristiques et fonctions seront annoncées séparément.

EnglishDeutschFrançais

TOOLS for TYROS INSTALLATION GUIDE

→

Important Notices about the CD-ROM

Data Types

This CD-ROM includes the application software, bit-map ﬁles, and demonstration movie ﬁles, etc. See page 3 (Windows) or 7 (Macintosh) for details. The applications allow you to edit TYROS voice data and transfer data between your computer and the TYROS.

Media format

The TYROS is compatible with the MS-DOS format.

Operating System (OS)

The applications in this CD-ROM are provided in versions for both Windows and Macintosh operating systems. The installation procedure and the applications themselves differ depending on the operating system that you are using. Please refer to the appropriate installation instructions.

Windows See page 3. Macintosh See page 7.

CD-ROM installation procedure

The following steps are the same for both Windows and Macintosh.

Verify that your system meets the operating requirements of

the software (Voice Editor, File Utility, driver, etc.) (Windows page 3, Macintosh page 7).

Connect the TYROS to your computer.

Refer to the owner’s manual for details on connections.

• Depending on the computer system you are using, some types of connections may not be possible.

Install the appropriate driver (USB or MIDI) to your com-

puter, and make the necessary settings. The arrow symbols shown below represent cables.

• Connection using a USB cable

USB connector of the TYROS ↔ USB connector of

the computer ........ Windows: page 4; Macintosh: page 8

Limitations on the TYROS when using the File Utility

The accessory CD-ROM contains a File Utility program. By using this software, you can transfer ﬁles between the internal memory or ﬂoppy disk of the TYROS and your computer, and edit them.There are some operating states of the TYROS in which it is not possible to use the File Utility or in which some File Utility functions are not available.

The following operations cannot be performed on the TYROS.

• Changing the name of a protected song (“Protected” song data includes commercially available songs that have been copied to the USER drive.)

• Copying a ﬁle within the same folder

• Transmitting a protected song to the computer

• Transmitting path information to a device

• Accessing the Preset drive.

You cannot use File Utility to perform ﬁle operations of the TYROS while the TYROS is in one of the following conditions.

• Demo mode

• Factory Reset execution

• Connection using MIDI cables

MIDI connector of the TYROS ← MIDI interface device

→

Computer ........Windows: page 6; Macintosh: page 9

Install the software (Voice Editor, etc.).

Refer to page 4 (Windows) or page 8 (Macintosh) for the installation procedure.

Start up the software.

For subsequent operations, refer to the owner’s manual for each software program (online help/PDF manual).

• In order to view PDF ﬁles, you will need to install Acrobat Reader in your computer (Windows: page 4; Macintosh: page 8).

• When transferring a ﬁle between the TYROS and your computer, you must set the type of characters on your TYROS to match the language of the operating system for the computer in which you installed File Utility. If the character code of the TYROS does not match the language of the computer that is running File Utility, the ﬁle may not be handled correctly.

• On the TYROS, the File Utility ID is ﬁxed at “1”. If you specify an ID other than “1,” you will be unable to transmit or receive data. For details on the File Utility ID, refer to the File Utility PDF manual.

TOOLS for TYROS INSTALLATION GUIDE

For Windows Users

Contents of the CD-ROM

The CD-ROM contains a variety of applications (with installers) and data in the following folders.

Folder Name Application Name Contents

Acroread_ Acrobat Reader

VoiceEditor_ Voice Editor for TYROS

FileUtil_ File Utility

FileConv_ File Converter

USBdrv_ YAMAHA USB MIDI Driver (for Win 98, Me)

USBdrv2k_ YAMAHA USB MIDI Driver (for Win 2000, XP)

*1 Unfortunately, Yamaha makes no guarantee concerning the stability of these programs nor can it offer user support for them. *2 All the applications listed above are supplied with online/PDF manuals. * You can start the File Utility or Voice Editor for TYROS software as either a stand-alone software or a plug-in application in the Open Plug-in Technology compatible application.

Refer to the owner’s manual of the client application (sequencer, etc.) for details on using the File Utility or Voice Editor for TYROS as a plug-in software.

PDF (Portable Document Format) viewer. Enables you to view each PDF manual for the applications.

Enables you to edit the TYROS voices on your computer.

Enables you to manage ﬁles in the USER/FD/HD (optional) drive of the TYROS.

Enables you to convert data of the PSR-8000 or PSR-9000/9000Pro for use with the TYROS.

Enables communication between the TYROS and your computer via a USB connection (for the indicated version of Windows).

Folder Name Contents

ScreenSaver Contains screen saver ﬁles for a computer.

Data

Movie Contains demonstration movie ﬁles.

WallPaper Contains Wall paper ﬁles for a computer.

PictureForTyros Contains the main picture or Song Lyrics display background pitcure of the TYROS.

Minimum System Requirements

The sytem requirements below may differ slightly depending on the particular operating system.

• Voice Editor for TYROS

Computer

Available Memory : 32 MB or more Hard Disk Display

: 166 MHz or higher; Intel : Windows 98/Me/2000/XP Home Edition/XP Professional

: 13 MB or more : 1024 x 768, High Color (16 bit)

• File Utility

Computer

Available Memory : 32 MB or more Hard Disk Display

: 166 MHz or higher; Intel : Windows 98/Me/2000/XP Home Edition/XP Professional

: 6 MB or more : 640 x 480, High Color (16 bit)

Pentium

/Celeron™ processor

• File Converter for TYROS

Computer

Available Memory : 32 MB or more Hard Disk Display

: 75 MHz or higher; Intel : Windows 98/Me/2000/XP Home Edition/XP Professional

: 2 MB or more : 640 x 480, High Color (16 bit)

Pentium

/Celeron™ processor

• USB MIDI Driver

Computer

Available Memory : 32 MB or more (64 MB or more is recommended) Hard Disk

: 166 MHz or higher; Intel : Windows 98/Me/2000/XP Home Edition/XP Professional

: 2 MB or more

Pentium

/Celeron™ processor

TOOLS for TYROS INSTALLATION GUIDE

For Windows Users

Software Installation

■

→

Windows 98/Me users See below.

→

Windows 2000 users See page 5.

→

Windows XP users See page 6.

• For details about the application software which has no installation guide described below, refer to the online manual of each software.

Uninstall (Removing the installed applictaion)

You can remove the installed applictaion software. Select [START] → [Settings] → [Control Panel] → [Add/ Remove Programs] → [Install/Uninstall], then select the application to be removed and click [Add/Remove...]. Follow the on-screen instructions to uninstall the application.

• The button names or menus may differ depending on the computer OS.

Acrobat Reader

In order to view the electronic (PDF) manuals included with each application, you’ll need to install Acrobat Reader.

• If an older version of Acrobat Reader is installed on your PC, you’ll need to uninstall it before proceeding.

Double-click on the “Acroread_” folder.

Four different language folders will be displayed.

Select the language you want to use and double-click on its

folder. The ﬁle “ar***.exe” ﬁle will be displayed. (“***” indicates the selected language.)

• Before you install the USB MIDI driver, you can minimize the possibility of problems by putting your computer in the following state.

• Close all applications and windows that you are not using.

• Disconnect all cables from the TYROS except for the cable whose driver you are installing.

Installing the driver on a Windows 98/Me system

Start the computer.

Insert the included CD-ROM into the CD-ROM drive.

Make sure the POWER switch on the TYROS is set to OFF

and use the USB cable to connect the USB terminal of the computer (or the USB hub) to the USB terminal of the TYROS. When the TYROS is turned on, the computer automatically displays the “Add New Hardware Wizard.” If the Add New Hardware Wizard does not appear, click “Add New Hardware” in the Control Panel.

• In Windows Me, check the radio button to the left of “Automatic search for a better driver (Recommended)” and click [Next]. The system automatically starts searching and installing the driver. Proceed to step #8. If the system does not detect the driver, select “Specify the location of the driver (Advanced)” and specify the CD-ROM drive’s “USBdrv_” to install the driver.

Windows 98

Double-click on “ar***.exe.”

Acrobat Reader Setup Dialog box will be displayed.

Execute the installation by following the on-screen direc-

tions.

After installation is complete, the Acrobat folder appears on your PC (in Program Files, as the default). For information on using the Acrobat Reader, refer to the Reader Guide in the Help menu.

USB MIDI Driver

To operate the TYROS from your computer via USB, you’ll need to install the appropriate driver software. The USB-MIDI driver is software that transfers MIDI data back and forth between sequence software and the TYROS via a USB cable.

Computer

Sequence

Software

Driver

USB cable

TYROS

Windows Me

TOOLS for TYROS INSTALLATION GUIDE

For Windows Users

Click [Next].

The window below enables you to select the search method.

Check the radio button to the left of “Search for the best

driver for your device. (Recommended).” Click [Next]. The window that enables you to select a location in which to install the driver appears.

Check the “CD-ROM drive” box and uncheck all other items.

Click [Next].

• The system may ask you to insert a Windows CD-ROM while it checks for the driver. Specify the “USBdrv_” directory of the CDROM drive (such as D:\USBdrv_\) and continue the installation.

When the system detects the driver on the CD-ROM and is

ready for installation, it displays the following screen. Make sure that the “YAMAHA USB MIDI Driver” is listed, and click [Next]. The system starts the installation.

Windows Me

The driver has been installed.

Installing the driver on a Windows 2000 system

Start the computer and use the “Administrator” account to log

into Windows 2000.

Select [My Computer] → [Control Panel] → [System] →

[Hardware] → [Driver Signing] → [File Signature Veriﬁcation], and check the radio button to the left of “Ignore -Install all ﬁles, regardless of ﬁle signature” and click [OK].

Insert the included CD-ROM into the CD-ROM drive.

Make sure the POWER switch on the TYROS is set to OFF

When the installation is complete, the following screen

appears. Click [Finish].

• Some computers may take about ten seconds to show this screen after the installation is complete.

Windows 98

Check the radio button to the left of “Search for a suitable

driver for my device. (Recommended).” Click [Next]. The window that appears enables you to select a location in which to install the driver.

Check the “CD-ROM drives” box and uncheck all other

items. Click [Next].

• The system may ask you to insert a Windows CD-ROM while it checks for the driver. Specify the “USBdrv2k_” directory of the CDROM drive (such as D:\USBdrv2k_\) and continue the installation.

When the installation is complete, the system displays “Com-

pleting the Found New Hardware Wizard.” Click [Finish].

• Some computers may take about ten seconds to show this screen after the installation is complete.

Restart the computer.

The driver has been installed.

TOOLS for TYROS INSTALLATION GUIDE

For Windows Users

MIDI Setup button

Installing the driver on a Windows XP system

Start the computer.

Select [Start] → [Control Panel].

If the control panel appears as shown below, click “Switch to Classic View” in the upper left of the window. All control panels and icons will be displayed.

Go to [System] → [Hardware] → [Driver Signing] → [File

Signature Veriﬁcation], and check the radio button to the left of “Ignore -Install all ﬁles, regardless of ﬁle signature” and click [OK].

Click the [OK] button to close System Properties, and then

click “X” in the upper right of the window to close the Control Panel.

Insert the included CD-ROM into the CD-ROM drive.

Make sure the POWER switch on the TYROS is set to OFF

Execute the installation by following the on-screen direc-

tions.

For details, refer to the on-line Help or the PDF owner’s manual.

■

File Converter

This software enables you to convert data of the PSR-8000 or PSR9000/9000Pro for use with the TYROS.

Double-click on the “FileConv_” folder in the CD-ROM.

“setup.exe” will be displayed.

Double-click on the “setup.exe” ﬁle.

The dialog will be displayed.

Execute the installation by following the on-screen direc-

tions.

For details, refer to the PDF manual.

MIDI port setting

(when starting the

software as a stand-alone application)

Before setting the MIDI port on the Voice Editor or File Utility, you should set the MIDI port from the MIDI SETUP toolbar.

• When you start the File Utility or Voice Editor as a plug-in application in the Open Plug-in Technology compatible application, refer to the the PDF manual for the respective software.

Start the Voice Editor or File Utility.

Click the MIDI Setup button in the Toolbar called up via step

#1.

Check the radio button to the left of “Search for a suitable

driver for my device. (Recommended).” Click [Next]. The system starts the installation.

When the installation is complete, the system displays “Com-

pleting the Found New Hardware Wizard.” Click [Finish].

• Some computers may take about ten seconds to show this screen after the installation is complete.

Restart the computer.

The driver has been installed.

■

Voice Editor, File Utility

Once you’ve installed these software programs, you can use your computer to edit the voices of the TYROS as well as access and organize data saved to the User/FD/HD drive in the TYROS.

Double-click on the “FileUtil_” or “VoiceEditor_” folder in

the CD-ROM. The ﬁle “setup.exe” will be displayed.

Double-click on the “setup.exe” ﬁle.

The TYROS Tools setup dialog will be displayed.

TOOLS for TYROS INSTALLATION GUIDE

In the MIDI Setup window called up via step #2, click the

[▼] button at the right end of each box and make the port settings as shown.

• In order for MIDI ports to be available here, you’ll need to select the relevant MIDI port within each application software (Voice Editor or File Utility). This is the port that will be used in the relevant MIDI applications. For details on setting the MIDI port, refer to the on-line manual of each software.

For Macintosh Users

Contents of the CD-ROM

The CD-ROM includes three folders: International, Japanese, and Data. Double-click on the appropriate folder to open it. A variety of applications (with their installers) are included in the International folder, while the Data folder contains various picture and movie ﬁles.

■ International folder

Folder Name Application Name Contents

Acroread_ Acrobat Reader

OMS_

USBdrv_ YAMAHA USB MIDI Driver

FileUtil_ File Utility

Open Music System (OMS)

OMS Setup for YAMAHA Contains the OMS Setup ﬁles for the Yamaha TYROS.

*1 *2

■ Data folder

Folder Name Contents

ScreenSaver Contains screen saver ﬁles for a computer.

Movie Contains demonstration movie ﬁles.

DesktopPicture Contains Wall paper ﬁles for a computer.

PDF (Portable Document Format) viewer. Enables you to view each PDF manual for the applications

Enables you to use several MIDI applications on the Mac OS.

Enables your computer to communicate with the TYROS when your computer and the TYROS are connected using a USB cable.

Enables you to manage ﬁles in the USER/FD/HD (optional) drive of the TYROS.

Minimum System Requirements

• File Utility

Computer : A Macintosh computer with a USB connector and a PowerPC or later CPU. OS : Mac OS 8.0 through OS 9.22 (Mac OS X is not supported) Available Memory : 6 MB or more Hard Disk : 4 MB or more (except for OMS) Display : 640 x 480, 256 colors or more Other : OMS 2.3.3 or later (included in the CD-ROM in the package)

• USB MIDI Driver

Computer : A Macintosh computer with a USB connector and a PowerPC or later CPU. OS : Mac OS 8.5 through OS 9.22 (Mac OS X is not supported) Memory : 64 MB or more (128 MB or more is recommended)

• Turn off virtual memory.

Hard disk : 2 MB or more Other : OMS 2.3.8 or later (included in the CD-ROM in the package)

TOOLS for TYROS INSTALLATION GUIDE

For Macintosh Users

Driver

TYROS

USB cable

Computer

Sequence

Software

OMS

Software Installation

■ Acrobat Reader

In order to view the electronic (PDF) manuals included with each application, you’ll need to install Acrobat Reader.

Double-click on the “Acroread_” folder.

Three different language folders will be displayed: English, German and French.

Select the language you want to use and double-click on its

folder. “Reader Installer” will be displayed. The Installer name may differ depending on the language you select.

Double-click on the “Reader Installer.”

Acrobat Reader Setup Dialog will be displayed.

Execute the installation by following the directions appearing

on the screen. After installation is complete, the Acrobat folder appears on your computer (in Hard Disk, as the default). For information on using the Acrobat Reader, refer to the Reader Guide in the Help menu.

■ USB MIDI Driver

First install OMS before you install the USB-MIDI driver. Also, after installing the driver, you will need to set up OMS (see page

9).

Start the computer.

Insert the included CD-ROM into the CD-ROM drive. The

system displays the CD-ROM icon on the desktop.

Double-click the CD-ROM icon and double-click the “Install

USB Driver” icon in the “USBdrv_” folder to display the following installation screen.

■ Open Music System (OMS) 2.3.8

OMS allows you to use several MIDI applications on the Mac OS at the same time.

Double-click on the “OMS_” folder (English version only).

“Install OMS 2.3.8” will be displayed.

Double-click on “Install OMS 2.3.8.”

OMS Setup Dialog will be displayed.

Execute the installation by following the on-screen direc-

tions. After the installation, select “Restart.”

• After the installation is complete, you may possibly encounter an error message warning that the installer did not close. In this case, go to the “File” menu and select “Quit” to close the installer. Then reboot the computer. After restarting the Macintosh, you will ﬁnd the “Opcode”/“OMS Applications” folder on your computer (Hard Disk, as the default).

Copy the “OMS_2.3_Mac.pdf” in the CD-ROM to the “OMS

Applications” folder (drag-and-drop it to the folder). Refer to the “OMS_2.3_Mac.pdf” (English version only) how to use the application.

Copy the “OMS Setup for YAMAHA” in the CD-ROM to the

“OMS Applications” folder (drag-and-drop it to the folder). In the “OMS Setup for YAMAHA” folder you will ﬁnd the OMS Setup ﬁles for the Yamaha tone generators, which can be used as templates.

The “Install Location” box displays the destination of the

installation. If you wish to change the destination disk or folder, use the [Switch Disk] button and the pop-up menu to specify the desired destination.

• This box usually displays the start-up disk as the destination.

Click the [Install] button. The system displays the following

message: “This installation requires your computer to restart after installing this software. Click Continue to automatically quit all other running applications.” Click [Continue].

• To cancel the installation, click [Cancel].

TOOLS for TYROS INSTALLATION GUIDE

The installation starts. If the driver has already been installed,

Indicates this setup is available

the following message appears. To return to step #3, press [Continue]. To complete the installation, click [Quit].

When the installation is complete, the system displays the

following message: “Installation was successful. You have installed software which requires you to restart your computer.” Click [Restart]. The computer automatically restarts. You can locate the installed ﬁles in the following locations:

• [System Folder] → [Control Panels] → [YAMAHA USB MIDI Patch]

• [System Folder] → [Extensions] → [USB YAMAHA MIDI Driver]

• [System Folder] → [OMS Folder] → [YAMAHA USB MIDI OMS Driver]

For Macintosh Users

Setting up OMS

The OMS studio setup ﬁle for the TYROS is contained in the included CD-ROM. This studio setup ﬁle is used for setting up OMS.

• Before performing the following procedure, the OMS and USB MIDI Driver should be installed (see page 8).

Use a USB cable to connect the USB terminal of the com-

puter (or the USB hub) to the USB terminal of the TYROS and turn the TYROS’ power on.

Start the computer.

Insert the included CD-ROM into the CD-ROM drive of your

Macintosh computer. The CD-ROM icon appears on the desktop.

Double-click on the CD-ROM icon, “OMS_”, and “OMS

Setup for YAMAHA.” The ﬁle “TYROS-USB” appears. Copy this to the hard disk on your computer.

Double-click on the “TYROS-USB” ﬁle to start the OMS

Setup.

After starting the OMS Setup, the Studio setup ﬁle double-

clicked in step #5 opens.

■ File Utility

Once you’ve installed the File Utility, you can use your computer to access and organize data saved to the User/FD/HD drive in the TYROS.

Double-click on the “FileUtil_” folder in the CD-ROM.

“Install File Utility” ﬁle will be displayed.

Double-click on the “Install File Utility” ﬁle.

The File Utility installation dialog will be displayed. Execute the installation by following the on-screen directions.

After installing, restart the computer.

For details, refer to the on-line Help or the PDF owner’s manual.

• If “ ” is not indicated at the right of the setup ﬁle name, select “Make Current” from the “File” menu and execute the save operation.

The OMS studio setup has been completed.

• After the OMS studio setup above has been completed, your computer will recognize only the TYROS as a MIDI instrument. If you use another MIDI instrument in addition to the TYROS or you add a second TYROS to the existing system, you should create an original Studio Setup ﬁle. For details, refer to the on-line manual supplied with the OMS.

TOOLS for TYROS INSTALLATION GUIDE

For Macintosh Users

Depending on the Macintosh and operating system version that you are using, the included studio setup ﬁle for the TYROS still may not work even after you have performed the above steps. (MIDI transmission and reception will not be possible even if the setup is valid.) In this case, use the following procedure to re-create the setup ﬁle.

Connect the TYROS and Macintosh via USB cable, and

turn on the power of the TYROS.

Start up OMS Setup, and from the “File” menu, choose

“New setup.”

The OMS driver search dialog box will appear.

Uncheck both [Modem] and [Printer] if you are using a USB connection.

Click the [Find] button to search for the device.

When a device has been found, the OMS Driver Setting dialog box will display the following.

For a USB connection: USB-MIDI 1

• If the device was found correctly, click the [OK] button to proceed.

• If the device was not found, re-check that the cable connections are correct, and repeat the procedure from step #1.

Make sure that the port is shown below the device that

was found. (This will be a name such as USB-MIDI.) Check the check box for the port, and then click the [OK] button.

A dialog box will appear, allowing you to name the ﬁle

that will be saved. Input the desired ﬁlename, and click [Save]. This completes the OMS setup.

From the “Studio” menu, choose “Test,” and click the

port icon. If a channel sounds on the TYROS, the system is operating correctly.

For details on using OMS, refer to “OMS_2.3_Mac.pdf,” included with OMS.

TOOLS for TYROS INSTALLATION GUIDE

Troubleshooting

The driver cannot be installed.

• Is the USB cable connected correctly?

→ Check the USB cable connection. → Disconnect the USB cable, then connect it again.

Windows

• Is the USB function enabled on your computer?

→ When you connect the TYROS to the computer for the ﬁrst

time, if the “Add New Hardware Wizard” does not appear, the USB function on the computer may be disabled (see pages 4,

5). Perform the following steps.

Double-click “System” in the Control Panel to open the

System Properties window.

Double-click the “Device Manager” tab and make sure

that no “!” or “x” marks appear at “Universal serial bus controller” or “USB Root Hub.” If you see an “!” or “x” mark, the USB controller is disabled. For more information, refer to the owner’s manual of your computer.

Windows

• Is any unknown device registered?

→ If driver installation fails, the TYROS will be marked as an

“Unknown device,” and you will not be able to install the driver. Delete the “Unknown device” by following the steps below.

Double-click “System” in the Control Panel to open the

System Properties window.

Double-click the “Device Manager” tab. With the “View

devices by type” check box checked, look for “Other devices.”

If you ﬁnd “Other devices,” double-click it to extend the

tree to look for “Unknown device.” If one appears, select it and click the [Remove] button.

Remove the USB cable from the TYROS, and make the

connection again.

Install the driver again.

→ Windows 98/Me users See page 4. → Windows 2000 users See page 5.

When controlling the TYROS from your computer via USB, the TYROS does not operate correctly or no sound is heard.

• Did you install the driver?

→ Windows users See page 4. → Macintosh users See page 8.

• Is the USB cable connected correctly?

• Are the volume settings of the tone generator, playback device, and application program set to the appropriate levels?

• Have you selected an appropriate port in the sequence software?

• Check whether the MIDI IN/OUT setting in the Utility mode corresponds to the interface actually in use (USB or MIDI).

Playback response is delayed.

• Does your computer satisfy the system requirements?

→ Windows users See page 3. → Macintosh users See page 7.

Macintosh

• Is any other application or device driver running?

→ Turn off virtual memory. → Disable AppleTalk.

Cannot suspend or resume the computer correctly.

• Do not suspend the computer while the MIDI application is running.

• If you are using Windows 2000, you may not be able to suspend/resume normally, depending on the particular environment (USB Host Controller, etc.). Even so, simply disconnecting and connecting the USB cable will allow you to use the TYROS functions again.

How can I delete or re-install the driver?

Windows Me/98

When the TYROS is recognized correctly, double-click

“System” in the Control Panel to open the System window.

Double-click the “Device Manager” tab, select

“YAMAHA USB MIDI Driver” and delete it.

Use the MS-DOS prompt or Explorer to delete the follow-

ing three ﬁles.

• \WINDOWS\INF\OTHER\YAMAHATYROS.INF

• \WINDOWS\SYSTEM\Xgusb.drv

• \WINDOWS\SYSTEM\Ymidusb.sys

• To delete the above ﬁles using Explorer, select “Folder Options” from the Tool (View) menu, and select “Show all ﬁles (and folders).”

Disconnect the USB cable.

Restart the computer.

Re-install the driver (see page 4).

Macintosh

Delete the ﬁles in the following locations:

• [System Folder] → [Control Panels] → [YAMAHA USB MIDI Patch]

• [System Folder] → [Extensions] → [USB YAMAHA MIDI Driver]

• [System Folder] → [OMS Folder] → [YAMAHA USB MIDI OMS Driver]

Restart the computer.

Install the driver (see page 8) and set up OMS (see page

9).

TOOLS for TYROS INSTALLATION GUIDE

+ 25 hidden pages