Yamaha SPS-80 Owners manual

Read this before setup

Thank you for selecting this YAMAHA SPS-80 speaker stand.

SPEAKER STAND

SPS-80

English

SETUP

INSTRUCTIONS

PRECAUTIONS

● This speaker stand is only for the speaker systems listed
in “USABLE SPEAKERS” below. Do not use the
speakers other than these listed.

● To prevent the speaker from falling, use the screws and
parts provided with the stand.

● To prevent the speaker stand from falling over, select a
location which is flat and stable.

● To avoid accidents resulting from tripping over loose
speaker cables and to prevent the speaker stand from
falling over, fix the speaker cables to the wall, etc.

● Do not let the children lean on the stand as this might
cause the serious accidents resulting from the falling
over of the speaker stand.

DIMENSIONS

(mm/inch)

Top view

300 (11-13/16”)

● To prevent the speaker stand from discoloring and
warping, keep the speaker stand away from the stoves
and places where it will be exposed to direct sunlight,
etc.

● Do not attempt to clean the speaker stand with chemical
solvents as this might damage the finish. Use a clean,
dry cloth.

● Secure placement or installation is the owner’s
responsibility.
YAMAHA shall not be liable for any accident caused
by improper placement or installation of speakers.

SPECIFICATIONS

Dimensions (W x H x D): 300 x 650 – 900 x 300mm

(11-13/16” x 25-9/16”
– 35-7/16” x 11-13/16”)

Weight: 2.1 kg (4 lbs. 10 oz.)

Français

Deutsch

Side view

M4 (3/16”)

595 (23-7/16”)

6 (1/4”)

47(1-7/8”)

650 (25-9/16”)

297 (11-11/16”)

153 (6”)

900 (35-7/16”)

USABLE SPEAKERS

YAMAHA

● NX-230P

(the main and rear speakers included in the NS-P230/
NS-P236 speaker package)

● NX-220P

(the main and rear speakers included in the NS-P220
speaker package)

● NX-S80S

(the front and rear speakers included in the AVX-S80
sound system)

● NX-S60S

(the front and rear speakers included in the DVX-S60
sound system)

● NX-S77E

(the rear speakers included in the AV-S77 sound
system)

● NX-VS10E

(the rear speakers included in the VS-10 sound system)

* Use a speaker of 1 kg or less.
* Use a speaker with a screw hole of 4 mm in diameter

for attaching the speaker mounting bracket.

(When shortened to minimum)

(When extended to maximum)

E-1

SETUP PROCEDURES

Before beginning the setup, check the parts list
and make sure all the parts are included.

NAME QUANTITY

1 Pole 2

2 Support 2

3 Base 2

4 + face screws 6

(Diam. x Length: 4 x 8 mm)

5 Hexagon socket set screws 5

(Diam. x Length: 4 x 6 mm)

6 Wrench (hexagonal) 1
7 Cable protection seal 2

8 Rubber cap 2

䡵 SETUP PROCEDURES

(You will need a screwdriver for the setup.)

1

Attach the support to the base by fastening the
three + face screws from the holes on the bottom
of the base.

Base

3

Remove the speaker mounting bracket from the
pole by removing the screw using the screwdriver.

Speaker
mounting
bracket

Pole

4

Attach the speaker mounting bracket to the
speaker by screwing it into the screw hole on the
bottom of the speaker.

Speaker
(not included)

Name plate

* Do not overtighten the + self-machine screws. Doing

so may damage the screws or assembly.

2

Pass the speaker cable through the support from
the bottom.

* A speaker cable more than 4 mm x 2 mm in diameter

cannot be used. If you use such a cable, connect it to
the speaker’s terminals without passing it through the
pole.

Support

Support

Speaker cable
(not included)

5

Pass the speaker cable through the pole from the
end without the cut.
Then pass the cable through the hole on the
speaker mounting bracket from the side with the
groove as shown in the figure.

Speaker cable

Cut

Pole

Front

Groove

Back

Speaker
mounting
bracket

E-2