YAMAHA RS700B User Manual [nl]

Receiver

OWNER’S MANUAL

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

IMPORTANT

Please record the serial number of this unit in the space below. MODEL: Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference.

1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod,

bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or when

unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

We Want You Listening For A Lifetime

Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, Yamaha and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.

i En

FCC INFORMATION (for US customers)

1 IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2 IMPORTANT:

accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3 NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices.

When connecting this product to

IMPORTANT SAFETY INSTRUCTIONS

Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/ reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., USA 6660 Orangethorpe Ave., Buena Park, CA 90620.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

ii En

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry,

clean place - away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following minimum clearances around this unit. Top: 30 cm (11-3/4 in) Rear: 20 cm (7-7/8 in) Sides: 20 cm (7-7/8 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall

onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage. 9 Do not use force on switches, knobs and/or cords. 10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable. 11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth. 12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage

other than specified. 13 To prevent damage by lightning, keep the power cable

and outdoor antennas disconnected from a wall outlet or

this unit during a lightning storm. 14 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any service is

needed. The cabinet should never be opened for any

reasons. 15 When not planning to use this unit for long periods of

time (i.e. vacation), disconnect the AC power plug from

the wall outlet. 16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

17 Before moving this unit, press A to set this unit to the

standby mode, and disconnect the AC power plug from the wall outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may

become warm. Turn the power off, then leave this unit alone for cooling.

20 Install this unit near the AC outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like.

22 Excessive sound pressure from earphones and

headphones can cause hearing loss.

As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you set this unit to standby mode by A. In this state, this unit is designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

This label is required to be attached to a product of which the temperature of the top cover may be hot during operation.

iii En

CONTENTS

INTRODUCTION

USEFUL FEATURES ............................................ 2

SUPPLIED ACCESSORIES ................................. 3

CONTROLS AND FUNCTIONS ......................... 4

Front panel ................................................................. 4

Front panel display .................................................... 6

Rear panel .................................................................. 7

Remote control........................................................... 8

Zone 2 remote control (R-S700 only) ...................... 10

Using the remote controls ........................................ 11

PREPARATION

CONNECTIONS .................................................. 12

Connecting speakers and source components..........12

Connecting the FM and AM antennas ..................... 14

Using COUPLER jacks (R-S700 only) ................... 15

Connecting power cable .......................................... 15

BASIC OPERATION

PLAYING AND RECORDING .......................... 16

Playing a source....................................................... 16

Adjusting the tonal quality....................................... 17

Recording a source .................................................. 19

Using the sleep timer ............................................... 19

FM/AM TUNING ................................................. 20

Automatic tuning ..................................................... 20

Manual tuning .......................................................... 21

Automatic station preset (FM stations only) ........... 22

Manual station preset ............................................... 23

Recalling a preset station ......................................... 24

Clearing a preset station........................................... 24

Clearing all preset stations....................................... 25

LISTENING TO SIRIUS Satellite Radio™....... 26

Connecting the SiriusConnect™ tuner .................... 27

Activating SIRIUS Satellite Radio™

subscription ......................................................... 27

SIRIUS Satellite Radio™ operations ...................... 28

Registering and recalling SIRIUS

Satellite Radio™ channels .................................. 30

Setting the Parental Lock......................................... 32

Displaying the SIRIUS Satellite Radio™

information .......................................................... 34

PLAYING BACK TUNES

FROM YOUR iPhone/iPod/

Bluetooth™ COMPONENT ............................ 35

Using a Universal Dock for iPod ............................. 36

Using a Wireless System for iPod ........................... 37

Using a Bluetooth Wireless Audio Receiver........... 38

ADVANCED OPERATION

SETTING THE OPTION MENU

FOR EACH INPUT SOURCE.........................40

Option menu items................................................... 40

ADVANCED SETUP ............................................43

Changing the ADVANCED SETUP

menu parameters.................................................. 43

Switching the remote control ID ............................. 44

ZONE 2 ..................................................................45

Connecting Zone 2 components .............................. 45

Controlling Zone 2................................................... 46

REMOTE CONTROL FEATURES ...................47

Controlling this unit, a TV, or other components .... 47

Configuring the remote control ............................... 49

ADDITIONAL INFORMATION

TROUBLESHOOTING .......................................50

SPECIFICATIONS...............................................57

PREPARATIONINTRODUCTION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

1 En

USEFUL FEATURES

This unit allows you to:

USEFUL FEATURES

Improve sound quality by using the CD Direct Amp*1 and Pure Direct functions

Play back music from your iPhone/iPod*2 or Bluetooth component

Play back video content from your iPhone/iPod

Listen to SIRIUS Satellite Radio channels

*1 *2

Listen to FM and AM radio stations

Boost bass sounds by connecting a subwoofer

Connect an external device*1 such as a graphic equalizer or a surround-sound processor

Use this unit’s remote control to operate other components such as a CD player, BD/DVD player or TV

Save power by using the automatic power down function

Use this unit to listen to another input source in two different rooms

R-S700 only

Optional Yamaha product required

Optional SiriusConnect tuner required

➡

p. 17

p. 35

p. 36

p. 26

p. 20

p. 12

p. 15

p. 47

p. 43

p. 45

iPhone, iPod

iPhone, iPod, iPod classic, iPod nano and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

Bluetooth™

Bluetooth is a registered trademark of the Bluetooth SIG and is used by Yamaha in accordance with a license agreement.

• y indicates a tip for your operation.

• This manual is the owner’s manual for both the R-S700 and the R-S500. Model names are given where the details of functions are unique to each model. Generally, illustrations of the R-S700 are used for explanations.

• Some operations can be performed by using either the buttons on the front panel of this unit or those on the remote controls. In case the button names differ between this unit and the remote controls, the names of the buttons on the remote controls are given in parentheses.

• In case the buttons on the remote control and the Zone 2 remote control have certain functions in common, the illustrations of the buttons on the remote control are used for explanation throughout the manual.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and the product, the product has priority.

2 En

SUPPLIED ACCESSORIES

Please check that you received all of the following parts.

Remote control

Zone 2 remote control

(R-S700 only)

Power cable

(R-S700 only)

Indoor FM antenna

INTRODUCTION

AM loop antenna

Batteries (x2)

(AAA, R03, UM-4)

■ Notes on remote controls and batteries

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following conditions: – places of high humidity, such as near a bath – places of high temperatures, such as near a heater or stove – places of extremely low temperatures – dusty places

• Use AAA, R03, UM-4 batteries for the remote control.

• Use a CR2025 battery for the Zone 2 remote control (R-S700 only).

• Insert batteries according to the polarity markings (+ and -).

• Change all batteries if you notice the operation range of the remote control narrows.

• If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak.

• If you find leaking batteries, discard the batteries immediately, taking care not to touch the leaked material. If the leaked material comes into contact with your skin or gets into your eyes or mouth, rinse it away immediately and consult a doctor. Clean the battery compartment thoroughly before installing new batteries.

• Do not use old batteries together with new ones. This may shorten the life of the new batteries or cause old batteries to leak.

• Do not use different types of batteries (such as alkaline and manganese batteries) together. Batteries that look the same may have a different specification.

• Before inserting new batteries, wipe the battery compartment clean.

• Dispose of batteries according to your regional regulations.

3 En

CONTROLS AND FUNCTIONS

Front panel

CONTROLS AND FUNCTIONS

(R-S700)

indicates buttons and controls that can also be used to control Zone 2. For more information about Zone 2, see pages 45 and 46.

1 MAIN ZONE A

Turns on this unit’s Main Zone unit or sets the Main Zone to standby mode (see page 16).

Note

In standby mode, this unit consumes a small amount of power to receive infrared signals from the remote control.

2 MAIN ZONE indicator

Lights up as follows: Brightly lit: Power is on Dimly lit: Standby mode

Note

The MAIN ZONE indicator is brightly lit while an iPhone/iPod is charging.

3 SPEAKERS A/B

Turns on or off the speaker set connected to the SPEAKERS A and/or SPEAKERS B terminals on the rear panel each time the corresponding button is pressed (see page 16).

4 DIMMER

Changes the brightness level of the front panel display. Choose brightness from 3 levels by pressing this button repeatedly.

This setting is retained even if you turn off this unit.

5 FM MODE/INFO

Changes the FM radio wave reception mode (stereo or monaural) when TUNER is selected as the input source (see page 21). Changes the SIRIUS Satellite Radio information displayed on the front panel display when SIRIUS is selected as the input source (see page 34). Changes the playback information displayed about the song playing on the iPhone/iPod when DOCK is selected as the input source (see page 36).

Note

Playback information can only be displayed for an iPhone/iPod that is connected using a Universal Dock for iPod.

6 MEMORY

Stores the current FM/AM station as a preset when TUNER is selected as the input source (see page 23). Stores the current SIRIUS channel as a preset when SIRIUS is selected as the input source (see page 30).

7 CLEAR

Clears the current FM/AM preset station when TUNER is selected as the input source (see page 24). Clears the current SIRIUS preset channel when SIRIUS is selected as the input source (see page 32).

8 Front panel display

Shows information about the operational status of this unit.

4 En

CONTROLS AND FUNCTIONS

9 PRESET j / i

Selects a preset FM/AM station when TUNER is selected as the input source (see page 24). Selects a preset SIRIUS channel when SIRIUS is selected as the input source (see page 31).

0 FM/CATEGORY l, AM/CATEGORY h

Sets the FM/AM tuner band to FM or AM when TUNER is selected as the input source (see page 20). Selects a channel category when SIRIUS is selected as the input source (see page 29).

A TUNING/CH jj / ii

Selects the tuning frequency when TUNER is selected as the input source (see page 20). Searches for a SIRIUS channel when SIRIUS is selected as the input source (see page 29).

B Remote control sensor

Receives infrared signals from the remote control.

Note

Switch the remote control ID between ID1 and ID2 when using multiple Yamaha receivers or amplifiers (see page 44).

C ZONE 2

Turns on Zone 2 or sets ZONE 2 to standby mode. When Zone 2 is turned on, signals are output to the ZONE 2 OUT jacks (see page 45).

D ZONE 2 CONTROL

Allows buttons and controls on the front panel to be used to control Zone 2. For more information about controlling Zone 2, see page 46.

E CD DIRECT AMP and indicator (R-S700 only)

Allows you to listen to a CD source in the purest possible sound (see page 17). The indicator lights up and the front panel display turns off when this function is turned on.

H REC OUT selector

Selects a source for recording to a CD recorder or to a tape deck independently of the INPUT selector setting, allowing you to record the selected source while listening to another source (see page 19).

I BASS control

Increases or decreases the low frequency response. The center position produces a flat response (see page 18).

J TREBLE control

Increases or decreases the high frequency response. The center position produces a flat response (see page 18).

K BALANCE control

Adjusts the sound output balance of the left and right speakers to compensate for sound imbalances caused by speaker locations or listening room conditions (see page

18).

L LOUDNESS control

Retains a full tonal range at any volume level to compensate for the human ears’ loss of sensitivity to high and low-frequency ranges at a low volume level (see page

18).

M INPUT selector

Selects the input source you want to listen to.

N VOLUME control ( R-S700 only)

Increases or decreases the sound output level.

Note

This does not affect the output level of the REC jacks.

INTRODUCTION

Notes

• If both the CD DIRECT AMP and the PURE DIRECT are turned on, only the CD DIRECT AMP will function.

• Zone 2 cannot be used while this function is turned on.

F PURE DIRECT and indicator

Allows you to listen to a source in the purest possible sound (see page 17). The indicator above it lights up and the front panel display turns off when this function is turned on.

Note

Zone 2 cannot be used while this function is turned on.

G PHONES jack

Outputs audio to your headphones for private listening.

Note

Press SPEAKER A/B so that the SP A/B indicators turn off before you connect your headphones to the PHONES jack.

5 En

CONTROLS AND FUNCTIONS

Front panel display

1 SP (SPEAKERS) A/B indicators

Light up according to the set of speakers selected. Both indicators light up when both sets of speakers are selected.

2 Input source indicators

Light up brightly to indicate the input source that is currently selected.

3 PRESET indicator

Lights up when you recall a preset radio station or SIRIUS channel. Blinks while the automatic station preset feature is scanning for FM stations to register as presets.

4 MEMORY indicator

Lights up or blinks when an FM/AM station or SIRIUS channel is being stored as a preset.

5 CATEGORY indicator

Lights up when searching for a SIRIUS channel by category.

6 TUNED indicator

Lights up when this unit is tuned in to an FM or AM station.

7 STEREO indicator

Lights up when this unit is receiving a strong signal for an FM stereo broadcast.

8 HOLD indicator

Blinks when the hold function is used to display the artist name, song title, etc. while listening to a SIRIUS channel.

B P indicator

Lights up when a preset number is selected. Blinks while you are registering a preset radio station or SIRIUS channel.

C Multi-information display

Shows information when adjusting or changing settings.

D Volume indicator

Displays the current volume level.

9 ZONE 2 indicator

Lights up when Zone 2 is turned on.

0 SLEEP indicator

Lights up when the sleep timer is turned on.

A MUTE indicator

Blinks while the MUTE function is turned on.

6 En

Rear panel

CONTROLS AND FUNCTIONS

INTRODUCTION

(R-S700)

1 TRIGGER OUT jack (R-S700 only)

When this unit is turned on or when a certain input source is selected, this unit can send a 12 V/100 mA direct electric current via the TRIGGER OUT jack that can be used to control an external component. The current is sent according to the “Trigger out” setting in the Option menu (see page 40).

Note

Do not connect a component that requires more than 100 mA of electric current, otherwise the component may not perform consistently or properly due to insufficient power.

2 REMOTE 2 IN jack (R-S700 only)

Used to receive remote control signals (see page 45).

3 REMOTE 1 IN/OUT jacks

Used to send and receive remote control signals (see page

45).

4 GND terminal

Used to connect a turntable (see page 12).

5 ZONE 2 OUT jacks

Used to connect a Zone 2 component (see page 45).

6 Antenna terminals

Used to connect FM and AM antennas (see page 14).

7 TAPE jacks

Used to connect a tape deck (see page 12).

8 DOCK jack

Used to connect an optional Yamaha Universal Dock for iPod (such as the YDS-12), Wireless System for iPod (YID-W10), or Bluetooth Wireless Audio Receiver (YBA-10) (see page 35).

9 PHONO jacks

Used to connect a turntable (see page 12).

0 CD jacks

Used to connect a CD player (see page 12).

A LINE 1-3 jacks

Used to connect audio components (see page 12).

B iPod VIDEO output jack (R-S700 only)

Used to send iPhone/iPod video content to a video monitor, such as a TV (see page 35).

Note

Video content output is possible only when an iPhone/iPod is connected this unit using a Universal Dock for iPod (such as the YDS-12).

C SIRIUS jack

Used to connect SiriusConnect tuner (sold separately) (see page 27).

D COUPLER jacks (R-S700 only)

Used to connect an external unit (see page 15).

E SUBWOOFER OUT jack

Used to connect a subwoofer with built-in amplifier (see page 12).

F POWER MANAGEMENT switch

Used to enable or disable the automatic power down function. When this function is enabled, this unit’s Main zone and Zone 2 automatically enters standby mode if this unit is not operated for a certain amount of time (3 settings are available; see page 43).

G SPEAKERS terminals

Used to connect speakers (see page 12).

H IMPEDANCE SELECTOR switch

Used to select the impedance setting (see page 13).

I AC IN (R-S700 only)

Used to plug in the supplied power cable (see page 15).

7 En

CONTROLS AND FUNCTIONS

Remote control

This section describes the function of each button on the remote control used to control this unit or other components made by Yamaha or other manufacturers.

indicates buttons that can also be used to control Zone 2.

For more information about Zone 2, see pages 45 and 46.

2 RECEIVER A

Turns this unit on, or sets it to standby mode.

3 ID

Changes the remote control ID (see page 44).

4 MAIN/ZONE 2

Switches the zone to be operated by the remote control between the Main Zone and Zone 2 (see page 46).

5 SLEEP

Sets the sleep timer (see page 19).

6 Input selector buttons

Selects the input source and changes the control area (see page 47).

7 OPTION

Turns the OPTION menu on and off (see page 40).

8 SPEAKERS A/B

Turns on and off the set of speakers connected to the SPEAKERS A and/or SPEAKERS B terminals on the rear panel of this unit when the corresponding button is pressed.

9 MUTE

Mutes the sound output. Press again to restore the sound output to the previous volume level.

■ Common controls

The following buttons can be used no matter which input source is selected.

1 Infrared signal transmitter

Sends infrared signals.

0 VOLUME +/– ( R-S700 only)

Increases or decreases the sound output level.

Note

This does not affect the output level of the REC jacks.

A RETURN

Returns to the previous menu or ends the menu display when using the Option menu (see page 40).

B B / C / D / E / ENTER

Selects and confirms items in the Option menu (see page

40).

C CODE SET/RECEIVER

Used to program the remote control so that it can control your other external components (see page 49). After using the remote control to control one of your components, this button is used to switch the remote control to receiver mode so that remote control commands will be sent to this unit (see page 48).

8 En

CONTROLS AND FUNCTIONS

■ SIRIUS and FM/AM controls

The following buttons can be used when SIRIUS or TUNER is selected as the input source.

D TUN./CH H / I

Selects the tuning frequency when TUNER is selected as the input source (see page 20). Searches for a SIRIUS channel when SIRIUS is selected as the input source (see page 29).

E PRESET F / G

Selects a preset FM/AM station when TUNER is selected as the input source (see page 24). Select a preset SIRIUS channel when SIRIUS is selected as the input source (see page 31).

F FM/CATEGORY l, AM/CATEGORY h

Sets the FM/AM tuner band to FM or AM when TUNER is selected as the input source (see page 20). Selects a channel category when SIRIUS is selected as the input source (see page 29).

G Numeric buttons, ENTER

Specifies the frequency or the preset number of the FM/ AM station when TUNER is selected as the input source (see page 21). Specifies the channel number or preset number of the SIRIUS channel when SIRIUS is selected as the input source (see page 30).

H INFO

Changes the SIRIUS Satellite Radio information displayed on the front panel display when SIRIUS is selected as the input source (see page 34).

■ External component controls

The following buttons can be used to control external audio/video components when CD, TAPE, PHONO, LINE1, LINE2, or LINE3 is selected as the input source. For more information, see page 47.

A RETURN

B B / C / D / E / ENTER

G Numeric buttons, ENTER

I TOP MENU

J MENU

K DISPLAY

L SOURCE A

M External component control buttons

N TV control buttons

INTRODUCTION

■ iPod controls

The following buttons can be used when DOCK is selected as the input source for listening to an iPhone/ iPod. For more information, see page 35.

A REPEAT

B MENU/ Ee / b / a / ENTER

H INFO

I SHUFFLE

J B

K C

9 En

CONTROLS AND FUNCTIONS

Zone 2 remote control (R-S700 only)

This section describes the function of each button on the Zone 2 remote control, which is used to control Zone 2.

Insulation sheet

Note

The Zone 2 remote control comes with a battery already installed. Before using the Zone 2 remote control for the very first time, pull out the insulation sheet, as shown.

■ Common controls for Zone 2

The following buttons can be used no matter which input source is selected for Zone 2.

1 Infrared signal transmitter

Sends infrared signals.

2 A (Zone 2 standby)

Sets Zone 2 to standby mode.

6 MUTE

Mutes the sound output to Zone 2. Press again to restore the sound output to the previous volume level.

7 VOLUME +/–

Increases or decreases the sound output level of Zone 2.

■ SIRIUS and FM/AM controls

The following buttons can be used when SIRIUS or TUNER is selected as the input source for Zone 2.

8 FM/CATEGORY l, AM/CATEGORY h

Sets the FM/AM tuner band to FM or AM when TUNER is selected as the input source (see page 20). Selects a channel category when SIRIUS is selected as the input source (see page 29).

9 PRESET j / i

Selects a preset FM/AM station when TUNER is selected as the input source (see page 24). Selects a preset SIRIUS channel when SIRIUS is selected as the input source (see page 31).

0 TUN./CH jj / ii

Selects the tuning frequency when TUNER is selected as the input source (see page 20). Searches for a SIRIUS channel when SIRIUS is selected as the input source (see page 29).

A Numeric buttons, ENTER

■ iPod controls

The following buttons can be used when DOCK is selected as the input source for Zone 2, for listening to an iPhone/iPod. For more information, see page 35.

B MENU/ Ee / b / a / ENTER

C /

3 (Zone 2 on)

Turns on Zone 2.

4 ID

Changes the Zone 2 remote control ID (see page 44).

5 Zone 2 input selector buttons

Selects the desired input source for Zone 2.

10 En

CONTROLS AND FUNCTIONS

■ Yamaha CD player controls

The following buttons can be used to control a Yamaha CD player when CD is selected as the input source for Zone 2.

A Yamaha CD player control buttons

• s Stops playback

• e Pauses playback

• p Starts playback

• DISC SKIP Skips to the next disc in a CD changer

Using the remote controls

■ Installing batteries

AAA, R03, UM-4 batteries

• b Skips backward

• a Skips forward

• Ejects the disc

• w Rewinds playback

• f Fast-forwards playback

Note

Not all Yamaha CD players can be controlled by the Zone 2 remote control.

■ Operation range

The remote controls transmit a directional infrared beam. Be sure to aim the remote controls directly at the remote control sensor on the front panel of this unit or on the infrared signal receiver in Zone 2 during operation.

Approximately 6 m (20 ft)

INTRODUCTION

■ Replacing the battery in the Zone 2

remote control

Change the battery when the operation range of the Zone 2 remote control decreases.

Straight pin

CR2025 battery

Remote control or Zone 2 remote control

11 En

CONNECTIONS

Connecting speakers and source components

CAUTION

• Do not connect this unit or other components to the main power until all connections between components are complete.

• All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. Refer to the owner’s manual for each of your components.

• Use RCA cables for audio components (except for speaker connections and DOCK jack connections).

• The IMPEDANCE SELECTOR must be set to the appropriate position before connecting speakers. See page 13 for details.

• Do not let bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers.

Audio

out

Turntable

GND

Audio

out

Tape deck

For information about other components that can be connected to this unit, see page 35.

Audio

Speakers A

Audio

out

CD player

Audio

out

VCR, etc.

Audio

out

DVD player,

etc.

Audio

CD recorder,

etc.

Audio

out

Subwoofer

Speakers B

• The PHONO jacks are designed for connecting a turntable with an MM cartridge.

• Connect your turntable to the GND terminal to reduce noise in the signal. However, for some turntables, you may hear less noise

without the GND connection.

12 En

CONNECTIONS

■ IMPEDANCE SELECTOR switch

CAUTION

Do not change the IMPEDANCE SELECTOR switch while the power of this unit is turned on, as doing so may damage the unit. If the unit fails to turn on, the IMPEDANCE SELECTOR switch may not be fully slid to either position. If this is the case, remove the power cable and slide the switch all the way to either position. Select the switch position (LOW or HIGH) according to the impedance of the speakers in your system.

Switch

position

HIGH

LOW

• If you use one set (A or B), the impedance of each speaker must be 6 or 8

• If you make bi-wire connections, the impedance of each speaker must be 6 higher (R-S700) or 8 See page 13 for Bi-wire connection.

• If you use one set (A or B), the impedance of each speaker must be 4

• If you use two sets (A and B) simultaneously, the impedance of each speaker must be 8 higher.

• If you make bi-wire connections, the impedance of each speaker must be 4 higher. See page 13 for Bi-wire connection.

Impedance level

Ω or higher (R-S700)

Ω or higher (R-S500).

Ω or

Ω or higher (R-S500).

Ω or higher.

Ω or

■ Connecting speaker cables

Remove approximately 10 mm (3/8 in) of insulation from the end of each speaker cable.

Note

When inserting speaker cables into the speaker terminals, insert only the bare speaker wire. If insulated cable is inserted, the connection may be poor and sound may not be heard.

■ Bi-wire connection

Bi-wire connection separates the woofer from the combined midrange and tweeter section. A bi-wire compatible speaker has four binding post terminals. These two sets of terminals allow the speaker to be split into two independent sections. With these connections, the mid and high frequency drivers are connected to one set of terminals and the low frequency driver to another set of terminals.

This unit

Speaker

Connect the other speaker to the other set of terminals in the same way.

CAUTION

When making bi-wire connections, set the IMPEDANCE SELECTOR switch to HIGH or LOW depending on the impedance of your speakers: 6 Ω or higher: HIGH (R-S700) 8 Ω or higher: HIGH (R-S500) 4 Ω or higher: LOW See page 13 for more information about the IMPEDANCE SELECTOR switch.

Note

When making bi-wire connections, remove the shorting bridges or cables on the speaker.

To use the bi-wire connections, press SPEAKERS A and SPEAKERS B on the front panel or on the remote control so that both SP A and B light up on the front panel display.

PREPARATION

■ Connecting via banana plug

Tighten the knob and then insert the banana plug into the end of the corresponding terminal.

Banana plug

SPEAKERS A/B

13 En

CONNECTIONS

Connecting the FM and AM antennas

Indoor antennas for receiving FM and AM broadcasts are included with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals.

Note

If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center about outdoor antennas.

Indoor FM antenna

(included)

Outdoor FM antenna

Outdoor AM antenna

Use 5 to 10 m of vinylcovered wire extended outdoors from a window.

AM loop antenna

(included)

• The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

• The AM loop antenna should be placed away from this unit.

Ground (GND terminal)

For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

■ Assembling the supplied AM loop antenna

■ Connecting the wire of the AM loop antenna

14 En

CONNECTIONS

Using COUPLER jacks (R-S700 only)

Removing the jumper pins from the PRE OUT/MAIN IN jacks enables this unit to operate separately as a control amplifier or a power amplifier. These jacks are used to connect a signal-processing system such as a graphic equalizer or a surround-sound processor to this unit. If an external unit is connected to these jacks, the VOLUME control of this unit can be used to adjust the overall sound output level. To connect an external unit, first remove the jumper pins from the PRE OUT/MAIN IN jacks and then connect the input jacks of that external unit to the PRE OUT jacks or its output jacks to the MAIN IN jacks. For details, refer to the owner’s manual included with the external unit to be connected.

Jumper pins

Connecting power cable

Plug the power cable into the AC IN on the rear panel of this unit (R-S700 only). Plug the power cable into the AC wall outlet after all other connections are complete.

PREPARATION

Power cable (R-S700 only)

Notes

• If you do not use the COUPLER jacks, never remove the jumper pins from these jacks. If removed, no sound will be output from this unit.

• Before installing or removing the jumper pins, be sure to disconnect the power cable of the unit. Leaving the power cable connected could cause noise to be emitted from the speakers or damage the unit.

• When you use this unit as a power amplifier, connect the output jacks of the external control amplifier, etc. to the MAIN IN jacks of this unit. In this case, the controls of this unit will not function except the PHONES jack and the SPEAKERS A/B buttons. Use the controls on the external control amplifier to make volume adjustments, etc.

15 En

PLAYING AND RECORDING

CAUTION

Extreme caution should be exercised when you play back CDs encoded in DTS. If you play back a CD encoded in DTS on a CD player that does not support DTS, only noise will be heard, and this noise may damage your speakers. Check whether your CD player supports CDs encoded in DTS. Also, check the sound output level of your CD player before you play back a CD encoded in DTS.

Playing a source

SPEAKERS A/B INPUT selector

MAIN ZONE A

VOLUME

RECEIVER A

Input selector buttons

SPEAKERS A/B

3 Press SPEAKERS A and/or SPEAKERS B on

the front panel or on the remote control to select speakers A and/or speakers B.

When speaker set A or speaker set B are turned on, SP A or SP B is displayed on the front panel display accordingly (see page 6).

Notes

• When one set of speakers is connected using bi-wire connections, or when using two sets of speakers simultaneously (A and B), make sure SP A and SP B are displayed on the front panel display.

• When listening with headphones, turn off the speakers.

4 Play the source.

5 Rotate the VOLUME control on the front

panel (or press VOLUME +/– on the remote control) to adjust the sound output level.

You can adjust the tonal quality by using the BASS, TREBLE, BALANCE and LOUDNESS controls, the CD DIRECT AMP switch (R-S700 only), or the PURE DIRECT switch on the front panel (see page 17).

VOLUME +/–

1 Press MAIN ZONE A on the front panel (or

RECEIVER A on the remote control) to turn on this unit.

2 Rotate the INPUT selector on the front panel

(or press one of the input selector buttons on the remote control) to select the input source you want to listen to.

16 En

6 Press MAIN ZONE A on the front panel again

(or RECEIVER A on the remote control) to finish using this unit and set it to standby mode.

Adjusting the tonal quality

■ Using the CD DIRECT AMP switch (R-S700 only)

CD Direct Amp feature

Generates a normal phase and reverse phase signal for both the left and right channels from the input signal and uses the four electronic volumes to send a balanced signal to the amplifying circuit. This feature provides clearer sound as a result of:

• improved signal-to-noise ratio

• external noise canceling

• reduced distortion

Routes input signals from your CD player directly to the specially built-in amplifier for the CD player. As a result, the input signals bypass the INPUT selector and the BASS, TREBLE, BALANCE and LOUDNESS controls and then sent to the power amplifier, thus eliminating any alterations to the CD signals and creating the purest possible sound. The CD DIRECT AMP indicator lights up and the front panel display turns off after a few seconds.

PLAYING AND RECORDING

■ Using the PURE DIRECT switch

Routes input signals from your audio sources so that the input signals bypass the BASS, TREBLE, BALANCE and LOUDNESS controls, thus eliminating any alterations to the audio signals and creating the purest possible sound. The PURE DIRECT indicator lights up and the front panel display turns off after a few seconds.

PURE DIRECT switch

Notes

• Zone 2 cannot be used while the PURE DIRECT feature is turned on.

• The BASS, TREBLE, BALANCE, and LOUDNESS controls do not function while the PURE DIRECT feature is turned on.

• This setting is retained even if you turn off this unit.

OPERATION

BASIC

CD DIRECT AMP switch

Notes

• If both the CD DIRECT AMP and the PURE DIRECT switches are turned on, only the CD DIRECT AMP switch will function.

• Zone 2 cannot be used while the CD DIRECT AMP feature is turned on.

• The INPUT selector and the BASS, TREBLE, BALANCE, and LOUDNESS controls do not function while the CD DIRECT AMP feature is turned on.

• A CD player must be connected to the CD jacks in order to use the CD DIRECT AMP feature.

• This setting is retained even if you turn off this unit.

17 En

PLAYING AND RECORDING

■ Adjusting the BASS and TREBLE controls

TREBLE

BASS

The BASS and TREBLE controls adjust high and low frequency response. The center position produces a flat response.

BASS

When you feel there is not enough bass (low frequency sound), rotate clockwise to boost. When you feel there is too much bass, rotate counterclockwise to suppress. Control range: –10 dB to +10 dB (20 Hz)

TREBLE

When you feel there is not enough treble (high frequency sound), rotate clockwise to boost. When you feel there is too much treble, rotate counterclockwise to suppress. Control range: –10 dB to +10 dB (20 kHz)

■ Adjusting the LOUDNESS control

LOUDNESS VOLUME

VOLUME +/–

Retain a full tonal range at any volume level, thus compensating for the human ears’ loss of sensitivity to high and low-frequency ranges at low volume.

CAUTION

If the CD DIRECT AMP switch (R-S700 only) or the PURE DIRECT switch is turned on with the LOUDNESS control set at a certain level, the input signals bypass the LOUDNESS control, resulting in a sudden increase in the sound output level. To prevent your ears or the speakers from being damaged, be sure to press the CD DIRECT AMP switch (R-S700 only) or the PURE DIRECT switch after lowering the sound output level or after checking that the LOUDNESS control is properly set.

■ Adjusting the BALANCE control

BALANCE

The BALANCE control adjusts the sound output balance of the left and right speakers to compensate for sound imbalance caused by speaker locations or listening room conditions.

1 Set the LOUDNESS control to the FLAT

position.

2 Rotate the VOLUME control on the front

panel (or press VOLUME +/– on the remote control) to set the sound output level to the loudest listening level that you would listen to.

3 Rotate the LOUDNESS control until the

desired volume is obtained.

After setting the LOUDNESS control, enjoy listening to music at your preferred volume level. If the effect of the LOUDNESS control setting is too strong or weak, readjust the LOUDNESS control.

18 En

+ 49 hidden pages