Yamaha RS70 User Manual
RS70
ASSEMBLY INSTRUCTIONS
INTRODUCTION
Thank you for purchasing the Yamaha Electronic Drum Rack System RS70.
Before using, thoroughly read these assembly instructions, and use this product
safely and correctly.
■ Handling Precautions
• Do not alter the product. Doing so may result in damage or deterioration to the product.
• Do not step on or place heavy objects on the product. It may result in damage.
• Do not use or keep the product in places with extremely high temperature (places in direct sun-
light, close to a heater, in a closed car, etc.) or damp (bathroom, outside on a rainy day, etc.). It
may result in deformation, discoloration, stickiness, damage or deterioration.
•To clean the product, please wipe with a soft cloth or a damp cloth that has been wrung out
thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a
damp cloth that has been wrung out thoroughly to remove any remaining detergent.
benzine, thinner or alcohol as it may result in discoloration or deformation. Also pay close atten-
tion so as not to let the water and detergent come into contact with the cushions used in the
product, it may result in deterioration.
Do not use
PRECAUTIONS
Before using, please read this “Assembly Instruction” sheet, and use this product in a safe
and proper manner.
Especially for children, parents or an instructor
should teach the children the proper manner in
which to use the device.
WARNING
Always set the instrument on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the
instrument being unstable and overturning.
Make sure all bolts are tightened firmly. Loose bolts may result in the rack overturning or parts dropping causing injury.
When adjusting the height or angle, do not suddenly loosen the bolt. The pad may drop, the rack or pipes may slip, pinching or
causing injury to hands or fingers.
Do not sit or step on the rack. The rack may overturn or be damaged resulting in injury.
Please be careful when children are close to or touching the product. The product has many pipes and arms so careless
movement around the product may result in injury.
When setting the pads and modules, please pay close attention in regards to the handling and setting of cables. Feet may
become entangled in the cables resulting in falls.
CAUTION
Do not put your hands or feet under the foot pedal or foot switch. They may be pinched resulting in injury.
Watch your fingers when adjusting clamps. They may become pinched resulting in injury.
Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers.
If this symbol is ignored and the equipment is used improperly, fatal injury to per-
sons or serious damage could occur.
If this symbol is ignored and the equipment is used improperly, there is a danger
of injury to persons handling the equipment, and material damage could occur.
To prevent against accidents and injury
Please follow the cautions listed below
Caution (including danger, or warning). This
mark indicates cautions in which you should
pay close attention to.
Acts indicated with this icon are prohibited and
should not be attempted.
■ Inside This Package
Before setup, please make sure that all of the items listed below are present and accounted for. If anything is missing, please contact the dealer from whom you purchased
the unit.
◆ Overall Assembly RS70
(When the box is opened)
◆ Small Screws M5 X 8
(Module Holder Fixing Screws X4)
◆ Cable Band (x10)
◆ Assembly Instructions (this sheet)
Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury.
* Specifications are subject to change without notice.
■ RS70 Assembly
* Parts for the RS70's main structure have already been assembled before packing. After removing the unit from the box, follow the instructions described below to complete the assembly.
A Phillips (+) screwdriver is required when attaching the Drum Trigger Module module. Please prepare one before starting assembly.
After removing the unit from the box, remove all cushion material.
1
Setting up the parts
2
• Loosen the bolts on the movable arms and legs, as shown in the diagrams
below, then secure the bolts firmly once setting is complete.
Follow the setup order (q~u) in the diagrams shown below.
Caution : Make sure the bolts marked with a " " are loosened before setting up.
Module Holder Assembly
r
Cymbal Holder
t
Attaching the Drum Trigger Module
3
3-1 Remove the module holder from the holder clamp,
and use the supplied screws to attach the Drum
Trigger Module.
Make sure only the supplied screws are
used. Using any other screws may result
in the unit falling off the holder or damage.
3-2 Reattach the module holder to the holder clamp.
Left Leg Assembly
e
Caution
←
q
Caution
←
w
Right Leg Assembly
u
y
Side Arm (R) Assembly
Side Arm (L) Assembly
Loading...