Yamaha MSP10, MSP10M User Manual

MONITOR SPEAKER

MSP10 MSP10M

Owner’s manual Mode d’emploi Bedienungsanleitung Manual de instrucciones

Thank you for purchasing the Yamaha MSP10/10M monitor speaker system. The MSP10/10M features a compact bass reﬂex cabinet, with a 20 cm two-way cone speaker and a 2.5 cm titanium dome speaker. This powered bi-ampliﬁer speaker system faithfully reproduces sound and can be used for a wide range of applications, from personal home recordings to serious professional use. Please read this Owner’s Manual thoroughly to make the best use of the MSP10/10M’s quality functions for the longest period of time, and keep the manual in a safe place.

Precautions

Warnings

• Do not allow water to enter this unit or allow the unit to become wet. Fire or electrical shock may result.

• Connect this unit’s power cord only to an AC outlet of the type stated in this Owner’s Manual or as marked on the unit. Failure to do so is a ﬁre and electrical shock hazard.

• Do not scratch, bend, twist, pull, or heat the power cord. A damaged power cord is a ﬁre and electrical shock hazard.

• Do not place heavy objects, including this unit, on top of the power cord. A damaged power cord is a ﬁre and electrical shock hazard. In particular, be careful not to place heavy objects on a power cord covered by a carpet.

• If you notice any abnormality, such as smoke, odor, or noise, or if a foreign object or liquid gets inside the unit, turn it off immediately. Remove the power cord from the AC outlet. Consult your dealer for repair. Using the unit in this condition is a ﬁre and electrical shock hazard.

• Should this unit be dropped or the cabinet be damaged, turn the power switch off, remove the power plug from the AC outlet, and contact your dealer. If you continue using the unit without heeding this instruction, ﬁre or electrical shock may result.

• If the power cord is damaged (i.e., cut or a bare wire is exposed), ask your dealer for a replacement. Using the unit with a damaged power cord is a ﬁre and electrical shock hazard.

• Do not remove the unit’s cover. You could receive an electrical shock. If you think internal inspection, maintenance, or repair is necessary, contact your dealer.

• Do not modify the unit. Doing so is a ﬁre and electrical shock hazard.

Cautions

• When rack-mounting the unit, allow enough free space around the unit for normal ventilation. This should be: 10 cm at the sides, 30 cm behind, and 60 cm above. For normal ventilation during use, remove the rear of the rack or open a ventilation hole. If the airﬂow is not adequate, the unit will heat up inside and may cause a ﬁre.

• This unit has ventilation holes at the rear to prevent the internal temperature rising too high. Do not block this. Blocked ventilation holes are a ﬁre hazard.

• This unit is heavy. Use two or more people to carry it.

• Keep this unit away from the following locations: —Locations exposed to oil splashes or steam, such

as near cooking stoves, humidiﬁers, etc.

—Unstable surfaces, such as a wobbly table or

slope.

—Locations exposed to excessive heat, such as

inside a car with all the windows closed, or places that receive direct sunlight.

—Locations subject to excessive humidity or dust

accumulation.

• Hold the power cord plug when disconnecting it from an AC outlet. Never pull the cord. A damaged power cord is a potential ﬁre and electrical shock hazard.

• Do not touch the power plug with wet hands. Doing so is a potential electrical shock hazard.

Operating Notes

• Turn off all musical instruments, audio equipment, and speakers when connecting to this unit. Use the correct connecting cables and connect as speciﬁed.

• Always lower the volume control to minimum before turning on the power to this unit. A sudden blast of sound may damage your hearing.

• Do not raise the volume of headphones or speakers to a level that makes you feel uncomfortable. Listening to loud music for long periods can damage your hearing.

• This speaker is magnetic shielded. However, if a nearby monitor displays any uneven colors, place it further away from the monitor.

• You may feel a ﬂow of air in and out of the port on this unit. This is not abnormal and sometimes occurs when a program with a lot of bass range is played.

• XLR-type connectors are wired as follows: pin 1: ground, pin 2: hot (+), and pin 3: cold (–).

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN and YELLOW.

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

* This applies only to products distributed by YAMAHA KEMBLE

MUSIC (U.K.) LTD.

Front panel/Rear panel

Power/Clip indicator

This indicator lights up green when you turn the POWER switch on the rear panel ON. If the output level is too high, causing clipping at the ampliﬁer, the indicator lights up red. In this case, lower the input level.

2 3 5

–2 –1

0 –1 ON0

LOW

ON OFF

POWER

HIGH (80Hz)

TRIM

+1 OFF

LOW CUT

+4dB

MIN –6dB

SENSITIVITY INPUT

TRIM switches

These switches enable you to adjust the bass and treble for the MSP10/10M.

LOW: three positions

The LOW switch adjusts the bass range. With the “–1” and “–2” settings, the bass range is cut by

1.5 dB when based on a reference value of 50 Hz with the “0” setting.

HIGH: three positions

The HIGH switch adjusts the treble. With the “+1” setting, the treble range is boosted by 1.5 dB when based on a reference value of 10 kHz with the “0” setting. With “–1” setting, the treble range is cut by

1.5 dB.

LOW CUT switch

This switch turns on or off the high-pass ﬁlter that cuts frequency ranges below 80 Hz.

SENSITIVITY control

Adjust the volume according to the output sensitivity of the connected device. (The factory default setting is “MIN.”)

INPUT jack

This is an XLR-type balanced input jack.

POWER switch

This switch turns the power to the MSP10/10M on and off. When you turn this switch on, the power/ clip indicator lights up green.

Speciﬁcations

General speciﬁcations

Type........................................... Ampliﬁed 2Way Bass Reﬂex Powered Speaker (Bi-Amp.)

Crossover Frequency .................. 2.0 kHz, 30 dB/oct

Frequency Range ....................... 40 Hz to 40 kHz (–10 dB)

Sensitivity ..................................–10 dB at –6 dB position (for 100 dB/SPL, 1 m on Axis)

Maximum Output Level............. 110 dB (1 m on Axis)

Dimensiones (W

Weight.......................................20 kg

Speaker unit

Speaker Unit..............................LF: 20 cm Cone (4

Enclosure...................................Type: Bass Reﬂex

Amp.unit

Maximum Output Power............LF: 120 W at 400 Hz, THD= 0.02%, RL= 4

Input Sensitivity/Impedance ....... –6 dB to +4 dB/10 k

Hum & Noise.............................

Signal to Noise Ratio..................

Controls.....................................TRIM Switch

Connectors ...............................Input XLR-3-31

Power Indicator/Clip Indicator ... Green/Red LED

Power Requirement....................USA and Canada: AC 120 V, 60 Hz

Power Consumption...................150 W

Option.......................................Wall mounting bracket BWS251-300

D).......... 265

420

329 mm

Ω

, magnetic shielded)

HF: 2.5 cm Titan Dome (8

HF: 60 W at 10 kHz, THD= 0.02%, RL= 8

≤

–67 dBu (Volume= Min) DIN Audio ﬁlter

≥

98 dB (IEC-A Weighting)

LOW: 3 positions (0 dB, –1.5 dB, –3 dB at 50 Hz)

HIGH: 3 positions (+1.5 dB, 0 dB, –1.5 dB at 10 kHz) LOW CUT Switch: ON/OFF SENSITIVITY Control POWER Switch: ON/OFF

Europe: AC 230 V, 50 Hz Others: AC 240 V, 50 Hz

Ω

, magnetic shielded)

Ω

Ω Ω

Speciﬁcations and appearance are subject to change without notice.

For European Model Purchaser/User Information speciﬁed in EN55103-1 and EN55103-2. Inrush Current: 11A Conformed Environment: E1, E2, E3 and E4

Dimensions

Performance graph

Standard frequency response

+10

120

W: 265

2-M8 Screws

H: 420

2625.5 D: 329

61.5

Unit: mm

–10

–20

RESPONSE (dB)

–30

–40

10k1k100

FREQUENCY (Hz)

Block Diagram

HPF

TRIM

–1

HIGHLOW

LPF

INPUT

HPF

LOW CUTSENSITIVITY

–1

–2

Mounting the MSP10/10M on the wall

You can install the MSP10/10M on the wall using an optional Yamaha wall bracket BWS251-300. For more information on how to install it, refer to the instructions that come with the wall bracket. For the angle and position of installation, refer to the ﬁgure below. The wall should be strong enough to support the speaker and equivalent to a sheet of plywood with a thickness of 18 mm (11/16 inches) or more. Use appropriate tools for installation.

• Recommend for new constructions.

• Ask an installation specialist for instruction.

• Some installation parts may deteriorate due to friction or corrosion over a long period of time. For safety, check these parts and condition regularly.

MSP10/10M Mode d’emploi

Nous vous remercions d’avoir opté pour le système d’enceinte d’écoute MSP10/10M de Yamaha. Le système MSP10/10M dispose d’un coffret bass reﬂex compact avec un haut-parleur deux voies en cône de 20 cm et un haut-parleur avec un dôme en titane de 2,5 cm. Ce système d’enceinte active biampliﬁée reproduit le son avec ﬁdélité et peut avoir de nombreuses applications allant de l’enregistrement à domicile à un usage professionnel intensif. Veuillez lire attentivement ce Mode d’emploi aﬁn de tirer le meilleur parti des qualités du MSP10/10M durant de longues années. Conservez ensuite ce mode d’emploi dans un endroit sûr.

Précautions

Avertissements

• Evitez de mouiller l’appareil. Il y a risque d’incendie ou d’électrocution.

• Ne branchez le cordon d’alimentation de cet appareil qu’à une prise secteur qui répond aux caractéristiques données dans ce manuel ou sur l’appareil, faute de quoi, il y a risque d’incendie.

• Evitez de griffer, tordre, plier, tirer ou chauffer le cordon d’alimentation. Un cordon d’alimentation endommagé constitue un risque d’incendie ou d’électrocution.

• Ne posez pas d’objets pesants (à commencer par l’appareil lui-même) sur le cordon d’alimentation. Un cordon d’alimentation endommagé peut provoquer un incendie ou une électrocution. Cette précaution est notamment valable lorsque le cordon d’alimentation passe sous un tapis.

• Si vous remarquez un phénomène anormal tel que de la fumée, une odeur bizarre ou un bourdonnement ou, encore, si vous avez renversé du liquide ou des petits objets à l’intérieur, mettez l’appareil immédiatement hors tension et débranchez le cordon d’alimentation. Consultez votre revendeur pour faire examiner l’appareil. L’utilisation de l’appareil dans ces conditions constitue un risque d’incendie ou d’électrocution.

• Lorsque l’appareil tombe ou si le boîtier est endommagé, coupez l’alimentation, débranchez le cordon de la prise secteur et contactez votre revendeur. L’utilisation de l’appareil dans ces conditions constitue un risque d’incendie ou d’électrocution.

• Si le cordon d’alimentation est endommagé (s’il est coupé ou si un ﬁl est à nu), veuillez en demander un nouveau à votre revendeur. L’utilisation de l’appareil avec un cordon d’alimentation endommagé constitue un risque d’incendie ou d’électrocution.

• N’ouvrez jamais le boîtier de cet appareil. Il y a risque d’électrocution. Si vous pensez que l’appareil doit subir une révision, un entretien ou une réparation, veuillez contacter votre revendeur.

• Cet appareil ne peut pas être modiﬁé par l’utilisateur. Il y a risque d’incendie ou d’électrocution.

+ 15 hidden pages