Yamaha Magicstomp Bass Effects Processor User Manual
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets
FCC requirements. Modifications not expressly
approved by Yamaha may void your authority,
granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only
high quality shielded cables. Cable/s supplied
with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could void your FCC authorization to
use this product in the USA.
3. NOTE: This product has been tested and found
to comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements
provides a reasonable level of assurance that
your use of this product in a residential environment will not result in harmful interference with
other electronic devices. This equipment generates/uses radio frequencies and, if not installed
and used according to the instructions found in
the users manual, may cause interference
harmful to the operation of other electronic
devices. Compliance with FCC regulations does
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
not guarantee that interference will not occur in
all installations. If this product is found to be the
source of interference, which can be determined
by turning the unit “OFF” and “ON”, please try to
eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is
being affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC
line filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is
300 ohm ribbon lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce
satisfactory results, please contact the local
retailer authorized to distribute this type of
product. If you can not locate the appropriate
retailer, please contact Yamaha Corporation of
America, Electronic Service Division, 6600
Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those
products distributed by Yamaha Corporation of
America or its subsidiaries.
CANADA
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
• This applies only to products distributed by Yamaha Canada Music Ltd.
• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.
The exclamation point within the
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance
(servicing) instructions in the
literature accompanying the product.
The lightning flash with arrowhead
symbol, within the equilateral
triangle, is intended to alert the user
to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electrical shock.
2
IMPORTANT SAFETY INSTRUCTIONS
INFORMATION RELATING TO PERSONAL INJURY, ELECTRICAL SHOCK,
AND FIRE HAZARD POSSIBILITIES HAS BEEN INCLUDED IN THIS LIST.
WARNING-
uct, basic precautions should always be followed. These precautions include, but are not limited to, the following:
When using any electrical or electronic prod-
1. Read all Safety Instructions, Installation Instructions,
Special Message Section items, and any Assembly Instructions
found in this manual BEFORE making any connections, including connection to the main supply.
2. Do not attempt to service this product beyond that
described in the user-maintenance instructions. All other servicing should be referred to qualified service personnel.
3. Main Power Supply Verification: Yamaha products are
manufactured specifically for the supply voltage in the area
where they are to be sold. If you should move, or if any doubt
exists about the supply voltage in your area, please contact your
dealer for supply voltage verification and (if applicable) instructions. The required supply voltage is printed on the name plate.
For name plate location, please refer to the graphic found in the
Special Message Section of this manual.
4. WARNING: Do not place this product or any other
objects on the power cord or place it in a position where anyone
could walk on, trip over, or roll anything over power or connecting cords of any kind. The use of an extension cord is not
recommended! If you must use an extension cord, the minimum
wire size for a 25' cord (or less) is 18 AWG. NOTE: The smaller
the AWG number, the larger the current handling capacity. For
longer extension cords, consult a local electrician.
5. Ventilation: Electronic products, unless specifically
designed for enclosed installations, should be placed in locations
that do not interfere with proper ventilation. If instructions for
enclosed installations are not provided, it must be assumed that
unobstructed ventilation is required.
6. Temperature considerations: Electronic products should
be installed in locations that do not seriously contribute to their
operating temperature. Placement of this product close to heat
sources such as; radiators, heat registers etc., should be avoided.
7. This product was NOT designed for use in wet/damp
locations and should not be used near water or exposed to rain.
Examples of wet /damp locations are; near a swimming pool,
spa, tub, sink, or wet basement.
8. This product should be used only with the components
supplied or; a cart ,rack, or stand that is recommended by the
manufacturer. If a cart, rack, or stand is used, please observe all
safety markings and instructions that accompany the accessory
product.
9. The power supply cord (plug) should be disconnected
from the outlet when electronic products are to be left unused
for extended periods of time. Cords should also be disconnected
when there is a high probability of lightening and/or electrical
storm activity.
10. Care should be taken that objects do not fall and liquids
are not spilled into the enclosure through any openings that may
exist.
11. Electrical/electronic products should be serviced by a
qualified service person when:
a. The power supply cord has been damaged; or
b. Objects have fallen, been inserted, or liquids have been
spilled into the enclosure through openings; or
c. The product has been exposed to rain; or
d. The product does not operate, exhibits a marked change
in performance; or
e. The product has been dropped, or the enclosure of the
product has been damaged.
12. This product, either alone or in combination with an
amplifier and headphones or speaker/s, may be capable of
producing sound levels that could cause permanent hearing loss.
DO NOT operate for a long period of time at a high volume
level or at a level that is uncomfortable. If you experience any
hearing loss or ringing in the ears, you should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time
period before damage occurs.
13. Some Yamaha products may have benches and/or acces-
sory mounting fixtures that are either supplied as a part of the
product or as optional accessories. Some of these items are
designed to be dealer assembled or installed. Please make sure
that benches are stable and any optional fixtures (where applicable) are well secured BEFORE using. Benches supplied by
Yamaha are designed for seating only. No other uses are recommended.
92-469-3
PLEASE KEEP THIS MANUAL
3
4
Owner’s Manual
Thank you for purchasing the Yamaha MAGICSTOMP BASS.
To get the most out of this product, we urge you to thoroughly
read this manual before use. Also, please keep the manual in a
safe place for future reference.
Contents
Precautions ............................................................................ 6
Package Contents .................................................................. 6
MAGICSTOMP
Component Names & Functions............................................. 8
Top Panel ...................................................................................... 8
Rear Panel ..................................................................................... 8
Connections ......................................................................... 10
Using the MAGICSTOMP ...................................................... 12
Turn on the amplifier and play..................................................... 12
Try out some of the other patches ............................................... 12
Create your own sound ........................................................ 14
Use the knobs to adjust the effect ................................................ 14
Deep Edit .................................................................................... 15
Saving Patches .....................................................................18
Storing edited patches (STORE) ................................................... 18
Giving the patch a name ..................................................... 20
Giving the patch a name (Name Edit Mode) ............................... 20
Auto Feedback Reduction (AFR) Function ........................... 22
Switching the AFR Function ON .................................................. 22
Using the AFR Function ............................................................... 23
Tuner Mode .......................................................................... 24
Using the tuner ........................................................................... 24
Factory Set (Restore Factory Defaults) ................................ 25
Restoring the factory defaults ...................................................... 25
Editing Patches with a Computer ........................................ 26
Data Flow .................................................................................... 27
Using the Sound Editor for MAGICSTOMP .................................. 27
Error Messages ..................................................................... 32
Trouble Shooting .................................................................32
Specifications ....................................................................... 33
SOFTWARE LICENSING AGREEMENT ..................................... 34
BASS’ Main Features .......................................... 7
For Windows Users ........................................................................... 28
For Macintosh Users ......................................................................... 30
5
Precautions
•Avoid using the MAGICSTOMP in the following locations to prevent possible damage:
• In direct sunlight or next to heating equipment.
• In extremely cold or hot locations.
• Locations exposed to high humidity or excessive dust.
• Locations subject to strong shocks or vibration.
• Before making any connections, make sure that the power is switched OFF on the MAGICSTOMP
and any external devices.
•To protect speakers from possible damage, always set the VOLUME knob to “0” before switching
the power ON/OFF.
• When connecting any devices to this unit, make sure that the power is switched OFF first.
• Do not apply excessive force to the switches, knobs and controls.
• The MAGICSTOMP is a precision device. Handle it with care and avoid dropping or jarring it.
•For safety, always remove the power adaptor from the AC wall outlet if there is any danger of
lightning striking in your area.
•Keep the MAGICSTOMP away from neon signs or fluorescent lighting to prevent noise pickup.
•To prevent damage and possibly electrical shock, never open the case and tamper with the
internal circuitry.
• Never use benzene, thinner or other volatile liquids for cleaning, as these chemicals may cause
damage or discoloration to the finish. Always use a dry, soft cloth to wipe off dust and dirt.
Package Contents
The following items are included in the MAGICSTOMP package. Check to see that you have everything listed here.
•MAGICSTOMP ................................. 1
• CD-ROM ........................................... 1
•Power Adaptor * ................................ 1
• USB Cable ........................................ 1
* May not be included depending on your particular area. Please check with your Yamaha dealer.
CAUTION
• Before breaking the seal on the CD-ROM package, please carefully read
the “Software Licensing Agreement” on page 34.
•Never attempt to play back the included CD-ROM on an audio CD player.
Doing so may result in damage to your hearing as well as to your CD
player/audio speakers.
6
• Owner’s Manual (this booklet) .......... 1
• Effect List .......................................... 1
•Patch List .......................................... 1
MAGICSTOMP BASS’ Main Features
[Professional quality preset tone patches make the MAGICSTOMP ready
to use out of the box]
• Close collaboration between artists from around the world and our audio engineers has produced a variety of professional quality patches. The unit contains a total of 99 onboard patches
that are perfect for use with acoustic and electric basses. Additional patches that use a variety
of effects can be found in the patch library supplied in the accompanying CD-ROM. 99 User
Patches let you freely edit and store patches so you can create your own library of sounds.
[Feels and operates like a compact effector]
• Simple design and controls (4 knobs, 3 footswitches) provide bassists with a familiar operating
environment. Operation is simple and straightforward to provide quick sound creation.
[Deep Edit offers precision editing of effects]
• Edit any of the parameters in the patch’s effects or set parameters that are assigned to the
unit’s control knobs and then save. This function lets you fully customize your MAGICSTOMP.
[Harnessing the power of Yamaha’s DSP technology]
• The MAGICSTOMP utilizes a powerful 32-bit DSP designed by Yamaha to deliver amp simulations and effects from the BBT series bass amplifiers, from the DG series amplifiers, and from
the DG, AG, and UD-Stomp effects. It also produces a variety of digital effects derived from the
Yamaha SPX series with unprecedented audio quality and function.
[Upload new patch data via USB]
• Patches supplied on the accompanying CD-ROM or downloaded from the internet can be uploaded into the MAGICSTOMP via the USB cable. You can also store customized sound patches
in your computer.
[Edit effects on your computer with a software based patch editor]
• Connect the MAGICSTOMP to your computer using the supplied USB cable then use the accompanying “Sound Editor for MAGICSTOMP” to edit effect parameters. The computer-based
editor offers the same level of deep editing that is possible with the pedal, but with the convenience of viewing more information on the computer’s display.
[Built-in chromatic auto tuner]
• The MAGICSTOMP also includes a built-in chromatic auto tuner, which is extremely useful in
live performances and recording.
7
Component Names & Functions
■ Top Panel
q
w
■ Rear Panel
U99¤MAGICSTOMP
ó‡GAINfiMSTRáTONE
t
!1
e
r
yu
When monitoring through a pair of headphones, make sure you
properly adjust the volume so as not to damage your hearing.
8
i
o!0
Component Names & Functions
q Display
Displays information for the currently selected patch or operating conditions of the MAGICSTOMP.
w CONTROL Knobs
These are used to control patch parameters. (→ page 14)
e VOLUME Knob
Controls the overall output volume of the MAGICSTOMP. (→ page 12)
r STORE/EXIT Button
This button is used to store edited patches in the MAGICSTOMP (→ page 18), exit the Deep Edit
Mode (→ page 15), or Name Edit Mode (→ page 20).
t – Switch, + Switch, ON/OFF Switch
These switches select patches, switch the patch ON or OFF, or switch modes. (→ page 12, 13, 20,
22)
y INPUT Jack
For connecting an instrument such as a bass guitar, synthesizer, etc., to the MAGICSTOMP. (→ page
11)
u INPUT LEVEL HIGH/LOW Switch
Selects HIGH or LOW impedance to match the input level with the output level of the instrument
connected to the INPUT jack. (→ page 11)
i OUTPUT L/MONO, R Jacks
For connecting the MAGICSTOMP to a bass amplifier, recorder, PA mixer, etc. (→ page 11)
o USB Jack
For connecting the MAGICSTOMP to a computer. This lets you edit patch voices on the computer or
move patch data between the computer and the MAGICSTOMP. (→ page 27)
!0 AC IN Jack (Power Adaptor)
Connect the power adaptor to this jack. (→ page 10)
*Power is switched ON when the power adaptor is connected (and supplying power) to the main unit.
!1 PHONES Jack
A pair of headphones connected to this jack (stereo mini) let’s you practice or edit patches while
monitoring the MAGICSTOMP’s sound output through the headphones. Use the Volume Knob e to
adjust the volume.
* Output is still delivered from the OUTPUT jack i when a pair of headphones is connected to the PHONES jack.
9
Connections
CAUTION
• In order to prevent electric shock or damage to your equipment, turn OFF
the power on the bass amp, etc., and set the MAGICSTOMP’s volume to its
minimum level before making any connections.
• Use ONLY a Yamaha AC-10 Power Adaptor (or other adaptor specifically
recommended by Yamaha).
Using another adaptor may result in damage, overheating or fire, which
can be very dangerous.
• Make sure to use the recommended AC voltage as indicated on the power
adaptor.
• The MAGICSTOMP automatically switches “ON” when power is connected and supplied to the
device.
• Connect a bass, guitar or any line level instrument such as a synthesizer, etc., to the INPUT
jack. The MAGICSTOMP can also be connected to the effect loop of an amplifier, mixer, or
other similar device.
• Set the INPUT LEVEL switch to match the output level of the instrument or device that is
connected to the MAGICSTOMP. If the sound is distorted when the switch is set to the HIGH
position, change the setting to LOW. If you feel output is low when the switch is set to the LOW
position, change the setting to HIGH.
•When using patches with stereo output, we recommend connecting the MAGICSTOMP’s output jacks to a stereo device.
• When connecting the power adaptor to the MAGICSTOMP’s AC IN jack, you can wrap the
power adaptor cord around the cord hook as shown in the illustration below (this helps keeping
the plug from being accidentally pulled out).
10
CAUTION
• Don’t let the cord bend sharply or kink when wrapping the cord around
the hook. An excessive bend can cut the cord or start a fire.
AC IN jack
Cord hook
Power adaptor cord
Connections
● Using the MAGICSTOMP with a bass guitar or other instrument
Connecting to an amplifier,
etc. (monaural)
INPUT
(or POWER AMP INPUT)
L/MONO
*The AC adaptor’s shape will
vary according to the country
to which the device is shipped.
Power Adaptor
Electric
Outlet
Connecting to a mixer
(stereo)
INPUT
L/MONO
OUTPUT
L/MONO R
R
U99¤MAGICSTOMP
ó‡GAINfiMSTRáTONE
INPUT
INPUTAC IN
MAGICSTOMP
Connecting to a
recording device, etc.
INPUT INPUT
R
L/MONO
Bass Guitar, or
other instrument
● Using the MAGICSTOMP in an effect loop
Power Adaptor
Electric
Outlet
*The AC adaptor’s shape will
vary according to the country
to which the device is shipped.
OUTPUT
L/MONO R
AC IN
U99¤MAGICSTOMP
ó‡GAINfiMSTRáTONE
MAGICSTOMP
INPUT
EFFECT
SEND
Mixer, etc.
EFFECT
RETURN
RL
11
Loading...