YAMAHA HTR-6230 User Manual

Download

Page 1

HTR-6230

AV Receive r

OWNER’S MANUAL

Page 2

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

1 Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and use instructions

should be followed.

5 Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

6 Attachments – Do not use attachments not recommended by

the product manufacturer as they may cause hazards.

7 Water and Moisture – Do not use this product near water –

for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8 Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9 A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10 Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11 Power Sources – This product should be operated only from

the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12 Grounding or Polarization – This product may be equipped

with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

13 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

14 Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

15 Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16 Overloading – Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

17 Object and Liquid Entry – Never push objects of any kind

into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

18 Servicing – Do not attempt to service this product yourself

as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19 Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service personnel under the following conditions:

a) When the power-supply cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into the

product,

c) If the product has been exposed to rain or water,

Caution-i En

Page 3

IMPORTANT SAFETY INSTRUCTIONS

d) If the product does not operate normally by following

the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation,

e) If the product has been dropped or damaged in any

way, and

f) When the product exhibits a distinct change in

performance - this indicates a need for service.

20 Replacement Parts – When replacement parts are required,

be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

21 Safety Check – Upon completion of any service or repairs to

this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

22 Wall or Ceiling Mounting – The unit should be mounted

to a wall or ceiling only as recommended by the manufacturer.

23 Heat – The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

24 Outdoor Antenna Grounding – If an outside antenna or

cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

EXAMPLE OF ANTENNA GROUNDING

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810–20)

GROUNDING CONDUCTORS (NEC SECTION 810–21)

GROUND CLAMPS

ELECTRIC SERVICE EQUIPMENT

NEC – NATIONAL ELECTRICAL CODE

MAST

GROUND CLAMP

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)

FCC INFORMATION (for US customers)

1 IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2 IMPORTANT: When connecting this product to

accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3 NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

Caution-ii En

Page 4

Caution: Read this before operating your unit.

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at least 30 cm on the top, 20 cm on the left and right, and 20 cm on the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: – Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords. 10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. Yamaha will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

18 Before moving this unit, press ASTANDBY/ON to set this

unit in the standby mode, and disconnect the AC power plug from the wall outlet.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC wall outlet. Voltages are:

........................................ AC 110–120/220–240 V, 50/60 Hz

20 The batteries shall not be exposed to excessive heat such as

sunshine, fire or like.

21 Excessive sound pressure from earphones and headphones can

cause hearing loss.

22 When replacing the batteries, be sure to use batteries of the

same type. Danger of explosion may happen if batteries are incorrectly replaced.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by ASTANDBY/ON. In this state, this unit is designed to consume a very small quantity of power.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES-003.

POUR LES CONSOMMATEURS CANADIENS

Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

IMPORTANT

Please record the serial number of this unit in the space below. MODEL: Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference.

Caution-iii En

Page 5

Contents

INTRODUCTION

Features.................................................................... 2

Supplied accessories .................................................. 2

Functional overview................................................ 3

Front panel ................................................................. 3

Front panel display..................................................... 4

Remote control........................................................... 5

Rear panel .................................................................. 6

Quick start guide.....................................................7

PREPARATION

Preparation of remote control ............................... 8

Connections ............................................................. 9

Placing speakers......................................................... 9

Connecting speakers .................................................. 9

Connecting video components ................................. 11

Connecting other components ................................. 13

Using the VIDEO AUX jacks on the front panel ....15

Connecting the FM and AM antennas ..................... 15

Connecting the power cable..................................... 15

Turning on and off the power .................................. 15

Basic setup ............................................................. 16

BASIC OPERATION

Playback................................................................. 17

Basic procedure........................................................ 17

Additional operations............................................... 18

Selecting the SCENE templates ........................... 21

Selecting the desired SCENE template.................... 21

Creating your original SCENE templates ................23

Using remote control on the SCENE feature ........... 24

Sound field programs ...........................................25

Selecting sound field programs................................ 25

FM/AM tuning ...................................................... 27

Overview.................................................................. 27

FM/AM tuning operations ....................................... 27

Preset FM/AM stations ............................................ 27

Using iPod™ .......................................................... 29

Control and functions for iPod™............................. 29

Using Bluetooth™ components............................ 30

Pairing the Bluetooth™ receiver and your Bluetooth™

component ........................................................... 30

Playback of the Bluetooth™ component ................. 30

ADVANCED OPERATION

Set menu ................................................................ 31

Using set menu......................................................... 32

1 SOUND MENU .................................................... 32

2 INPUT MENU ...................................................... 34

3 OPTION MENU ................................................... 35

Remote control features ....................................... 37

Controlling this unit, a TV, or other components .... 37

Setting remote control codes.................................... 39

Advanced setup ..................................................... 40

ADDITIONAL INFORMATION

Troubleshooting .................................................... 41

Glossary ................................................................. 46

Specifications......................................................... 47

Index ...................................................................... 48

APPENDIX

(at the end of this manual)

List of remote control codes...................................i

About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the

front panel or the ones on the remote control. In case the button names differ between the front panel and the remote control, the button name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications

are subject to change in part as a result of improvements, etc. In case of differences between the manual and product, the product has priority.

• “ASTANDBY/ON” or “fDVD” (example) indicates the name of

the parts on the front panel or the remote control. Refer to the “Functional overview” on page 3.

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

1 En

APPENDIX

English

Page 6

INTRODUCTION

Features

Built-in 5-channel power amplifier

◆ Minimum RMS output power

[U.S.A. and Canada models] (1 kHz, 0.9% THD, 8 Ω) Front: 100 W/ch Center: 100 W Surround: 100 W/ch [Other models] (1 kHz, 0.9% THD, 6 Ω) Front: 100 W/ch Center: 100 W Surround: 100 W/ch

Various input/output connectors

◆ HDMI (IN x 2, OUT x 1), Component video (IN x 3, OUT x

1), Composite video (IN x 3, OUT x 2), Coaxial digital audio (IN x 1), Optical digital audio (IN x 2), Analog audio (IN x 9, OUT x 2)

◆ Speaker out (5-channel), Subwoofer out

◆ Discrete multi-channel input (6-channel)

SCENE select function

◆ Preset SCENE templates for various situations

◆ SCENE template customizing capability

Sound field programs

◆ Proprietary Yamaha technology for the creation of surround

field

◆ Compressed Music Enhancer mode

◆ SILENT CINEMA™

Decoders and DSP circuits

◆ Dolby Digital decoder

◆ Dolby Pro Logic/Dolby Pro Logic II decoder

◆ DTS decoder

◆ Virtual CINEMA DSP

◆ SILENT CINEMA™

Sophisticated FM/AM tuner

◆ 40-station random and direct preset tuning

◆ Automatic preset tuning

HDMI™ (High-Definition Multimedia Interface)

◆ HDMI interface for standard, enhanced or high-definition

video (includes 1080p video signal transmission)

DOCK terminal

◆ DOCK terminal to connect a Yamaha iPod universal dock

(such as YDS-11, sold separately) or Bluetooth wireless audio receiver (such as YBA-10, sold separately)

Other features

◆ 192-kHz/24-bit D/A converter

◆ iPod controlling capability

◆ Sleep timer

◆ Cinema and music night listening modes

◆ Remote control with preset remote control codes

Manufactured under license under U.S. Patent No’s: 5,451,942;5,956,674;5,974,380;5,978,762;6,487,535 and other U.S. and worldwide patents issued and pending. DTS is a registered trademark and the DTS logos and symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved.

iPod™

“iPod” is a trademark of Apple Inc., registered in the U.S. and other countries.

Bluetooth™

Bluetooth is a registered trademark of the Bluetooth SIG and is used by Yamaha in accordance with a license agreement.

“HDMI,” the “HDMI” logo and “High-Definition Multimedia Interface” are trademarks, or registered trademarks of HDMI Licensing LLC.

“SILENT CINEMA” is a trademark of Yamaha Corporation.

We Want You Listening For A Lifetime

Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion - and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, Yamaha and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.

Supplied accessories

Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories.

2 En

Check that you received all of the following parts.

❏ Remote control ❏ Batteries (2) (AAA, R03, UM-4) ❏ AM loop antenna ❏ Indoor FM antenna

Page 7

Front panel

C D G H I

T PE F

Functional overview

INTRODUCTION

VOLUME

EDIT

PRESET/TUNING

A/B/C/D/E

CONTROL

TONE

K OL N R

STANDBY

SPEAKERS

PHONES

/ON

SILENT

CINEMA

A STANDBY/ON

Turns on this unit, or sets it to standby mode (see page 15).

B PHONES jack

Connect to a pair of headphones (see page 19).

C SPEAKERS

Turns on or off the set of front speakers connected to the FRONT A or FRONT B speaker terminals (see page 18).

D EDIT PRESET/TUNING

Switches the tuning mode (see page 27).

E A/B/C/D/E

Selects the preset station group (A to E) (see page 28).

F PRESET/TUNING l / h

Tunes into radio stations manually or automatically and selects a preset station group (see page 27).

G BAND

Selects the reception band from FM and AM (see page 27).

H MEMORY

Stores a station that you tuned into as a preset station (see page 27).

I TUNING AUTO/MAN’L

Selects a tuning method from automatic or manual tuning (see page 27).

J SCENE 1/2/3/4

Recalls an input source and a sound field program assigned to each SCENE button (see page 21).

K TONE CONTROL

Selects “BASS” and “TREBLE” to adjust frequency response (see page 19).

L PROGRAM l / h

Selects a sound field program (see page 25).

M STRAIGHT

Activates the “STRAIGHT” mode (see page 26).

N INPUT l / h

Selects an input source (see page 17).

O NIGHT

Selects a night listening mode (see page 19).

PROGRAM

PRESET/TUNING

SCENE

STRAIGHT

EFFECT

INPUT

MEMORY

BAND

NIGHT

TUNING

AUTO/MAN'L

AUX

VIDEO

AUDIO

PORTABLE

OPERATION

BASIC

J QSBM

PREPARATION

P VOLUME c ontrol

Adjusts the volume level of this unit (see page 17).

Q VIDEO (VIDEO AUX) jack

Connects to a game console or a video camera using a composite video cable (see page 15).

OPERATION

ADVANCED

R AUDIO L/R (VIDEO AUX) jacks

Connects to a game console or a video camera using analog audio cables (see page 15).

S PORTABLE (VIDEO AUX) jack

Connects to an audio component (such as iPod) (see page 15).

T Front panel display

Shows information about the operational status of this unit (see

INFORMATION APPENDIX

ADDITIONAL

page 17).

English

3 En

Page 8

Functional overview

ab c de f ghi

jklmnopq

Front panel display

PCM

ENHANCER

DIGITAL

VIRTUAL

DVR DVD CD

a Decoder indicator

Lights up when any of the decoders of this unit functions.

b ENHANCER indicator

Lights up when the Compressed Music Enhancer mode is selected (see page 25).

c VIRTUAL indicator

Lights up when Virtual CINEMA DSP is active (see page 26).

d SILENT CINEMA indicator

Lights up when headphones are connected and a sound field program is selected (see page 26).

SILENT CINEMA

A B

V-AUX DTV/CBL

DOCK

NIGHT

MD/CD-R

AUTO

TUNED

TUNER

STEREO

MEMORY

PRESET

SLEEP

MUTE

q Input channel and speaker indicators

LFE

LCR

SL SR

• LFE indicator

Lights up when the input signal contains the LFE signal.

• Input channel indicators

Indicates the channel components of the current digital input signal.

LFE indicator

Input channel indicators

e DOCK indicator

Lights up or flashes according to the state of Yamaha iPod universal dock or Bluetooth Wireless Audio Receiver connected to this unit (see pages 14 and 30).

f Input source indicators

The corresponding cursor lights up to show the currently selected input source.

g Tuner indicators

Lights up when this unit is in the FM or AM tuning mode (see page 27).

h MUTE indicator

Flashes while the MUTE function is on (see page 19).

i VOLUME level indicator

Indicates the current volume level.

j PCM indicator

Lights up when this unit is reproducing PCM (Pulse Code Modulation) digital audio signals.

k Headphones indicator

Lights up when headphones are connected (see page 19).

l SP A B indicators

Lights up according to the set of front speakers selected (see page 17).

m NIGHT indicator

Lights up when you select a night listening mode (see page 19).

n CINEMA DSP indicator

Lights up when you select a sound filed program (see page 26).

o Multi-information display

Shows the name of the current sound field program and other information when adjusting or changing settings.

p SLEEP indicator

Lights up while the sleep timer is on (see page 20).

VOLUME

LFE

LCR

SL SR

4 En

Page 9

Remote control

POWER

POWER POWER

ABAVC

DVD

V-AUX/DOCK

AMP

BAND LEVEL

TITLE

RETURN

REC

PROG

STRAIGHT

MULTI CH IN

a Infrared window

Outputs infrared control signals (see page 8).

b TV/AV POWER

Turns your TV or other components on or off (see page 38).

c STANDBY ( )

Sets this unit to the standby mode (see page 15).

d POWER ( )

Turns this unit on (see page 15).

e MUTE

Mutes audio output (see page 19).

f Input selector buttons

Switches the input source to each source (see page 17).

g TV control buttons

Controls your TV (see page 37).

STANDBY

MD/CD-R

TUNER

DTV/CBL

DVR

D E

TV INPUT TV MUTE

SCENE

ENTER

ENHANCER

2341

NIGHT

607

AUDIO SEL

MUTE

TV CH

TV VOL

VOLUME

DISPLAY

SUR.DECODE

SLEEP

ENT

s u

Functional overview

h AMP

Press this button before you control this unit (see page 17).

i SCENE 1/2/3/4

Recalls an input source and a sound field program assigned to each SCENE button (see page 21).

j BAND LEVEL TITLE

Selects the speaker that you want to adjust (see page 19).

k MENU

Displays the set menu on the front panel display (see page 32).

l Cursors (l / h / n / k) / ENTER

• Press cursors to navigate the set menu (see page 32).

• Press ENTER to confirm a selection in the set menu (see page 32).

m VOLUME + /–

Adjusts the volume level of this unit (see page 17).

n RETURN

Returns the previous menu level when the set menu is displayed (see page 32).

o DISPLAY

Displays the information of external components (such as a DVD player) (see page 38).

p Control buttons

Control external components (such as a DVD player) connected to this unit (see page 38).

q PROG l / h

Selects the sound field program (see page 25).

r ENHANCER

Sets the sound field program to the “Music Enh. 2ch” or “Music Enh. 5ch” (see page 25).

s SUR.DECODE

Selects a decoder from four decoders (see page 26).

t STRAIGHT

Activates the “STRAIGHT” mode (see page 26).

u NIGHT

Selects a night listening mode (see page 19).

v MULTI CH IN

Sets the input source to MULTI CH IN (see page 18).

w AUDIO SEL

Selects an audio input select setting for each input source (see page 18).

x SLEEP

Sets the sleep timer (see page 20).

y Numeric buttons

Enter remote control codes or preset station number (see page 39).

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

English

5 En

Page 10

Functional overview

e fc db

Rear panel

DOCK

DIGITAL INPUT

OPTICAL

COAXIAL

COMPONENT VIDEO

DVD

DTV/CBL

DTV/ CBL

DVD

MULTI CH INPUT

FRONT

g h i j

a DOCK terminal

Connect to the Yamaha iPod Universal Dock (such as YDS-11, sold separately) or Bluetooth Wireless Audio Receiver (such as YBA-10, sold separately) using its dedicated cable (see page 14).

b COMPONENT VIDEO jacks

Connect to Y, PB/CB and PR/CR jacks on your video components with component video cables (see page 11).

• DVD input jacks

• DTV/CBL input jacks

• DVR input jacks

• MONITOR OUT output jacks

c HDMI terminals

Connect to HDMI output/input terminals on your external components with HDMI cables (see page 11).

• HDMI DVD terminal

• HDMI DTV/CBL terminal

• HDMI OUT output terminal

d VIDEO jacks

Connect to video jacks on your video components with composite video cables (see page 11).

• DVD input jack

• DTV/CBL input jack

• DVR IN jack

• DVR OUT jack

• MONITOR OUT jack

e ANTENNA terminals

Connect to the supplied FM and AM antennas (see page 15).

f SPEAKERS terminals

Connect to each speakers (see page 9).

• FRONT A L/R

• FRONT B L/R

• SURROUND L/R

• CENTER

g DIGITAL INPUT jacks

Connect to the DIGITAL output jacks on your digital audio components with Coaxial/Optical digital audio cables.

DVR

SURROUND

MONITOR

OUT

CENTER

SUBWOOFER

AUDIO

HDMI

MONITOR

OUT

ANTENNA

GND

UNBAL.

MD/

OUT

CD-R

(PLAY)

(REC)

OUT

DVD

DTV/CBL

DVD

VIDEO

DVR

OUT

DVR

OUT

OUTPUT

SUB

WOOFR

SURROUND

SPEAKERS

CENTER

FRONT B

FRONT A

This input jacks support PCM, Dolby Digital and DTS bitstream (see page 11).

• COAXIAL (DVD)

• OPTICAL (DTV/CBL)

• OPTICAL (CD)

h MULTI CH INPUT jacks

Connect to the output jacks on your multi-format player or external decoder with analog audio cables (see page 14).

• FRONT L/R jack

• SURROUND L/R jack

•CENTER jack

• SUBWOOFER jack

i AUDIO jacks

Connect to the audio output/input jacks on your components with analog audio cables (see page 11).

• DVD L/R jack

• DTV/CBL L/R jack

• DVR IN L/R jack

• DVR OUT L/R jack

• CD L/R jack

• IN (PLAY) L/R jack

• OUT (REC) L/R jack

j SUBWOOFER OUTPUT jack

Connect to a Subwoofer with an analog audio cable (see page 9).

k Power cable

Connect to a standard AC outlet (see page 15).

6 En

Page 11

Quick start guide

The following steps describe the easiest way to operate this unit. See the related pages for details on the operation and settings.

Step 1: Check the items

Step 3: Connect your components

INTRODUCTION

In these steps, you need the following items which are not included in the package of this unit.

❏ Speakers

We recommend magnetically shielded speakers.

❏ Front speaker ..................................... x 2

At least two front speakers are required to start playback.

❏ Center speaker ................................... x 1

❏ Surround speaker .............................. x 2

❏ Active subwoofer ................................... x 1

Select an active subwoofer equipped with an RCA input jack.

❏ Speaker cable ......................................... x 5

❏ Subwoofer cable ..................................... x 1

Select a monaural RCA cable.

❏ DVD player .............................................. x 1

Select DVD player equipped with coaxial digital audio output jack and composite video output jack.

❏ Video monitor ......................................... x 1

Select a TV monitor, video monitor or projector equipped with a composite video input jack.

❏ Video cable ............................................. x 2

Select an RCA composite video cable.

❏ Digital coaxial audio cable .................... x 1

Connect your TV, DVD player or other components.

• Connecting a TV monitor or projector ☞P. 1 2

• Connecting audio and video components ☞P. 1 3

• Connecting a multi-format player or an external

decoder ☞P. 1 4

• Connecting a Yamaha iPod universal dock or

Bluetooth Wireless Audio Receiver ☞P. 1 4

• Using the VIDEO AUX jacks on the front panel

☞P. 1 5

• Connecting the FM and AM antennas ☞P. 1 5

Step 4: Turn on the power

Connect the power cable and turn on this unit.

• Connecting the power cable ☞P. 1 5

• Turning on and off the power ☞P. 1 5

Step 5: Select the input source and start playback

Select the component connected in the step 3 as an input source and start playback.

• Basic procedure ☞P. 1 7

• Selecting the SCENE templates ☞P. 2 1

• Adjusting the sound field programs ☞P. 2 5

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

Step 2: Set up your speakers

Place your speakers in the room and connect them to this unit.

Front right

Video monitor

Front left

speaker

Center speaker

DVD p layer

• Placing speakers ☞P. 9

• Connecting speakers ☞P. 9

speaker

Surround left

speaker

Subwoofer

Surround right

speaker

English

7 En

Page 12

PREPARATION

Preparation of remote control

Installing batteries in the remote control

1 Take off the battery compartment cover.

2 Insert the four supplied batteries (AAA, R03,

UM-4) according to the polarity markings (+ and –) on the inside of the battery compartment.

3 Snap the battery compartment cover back

into place.

Notes

• Change all of the batteries if you notice the following conditions: – the operation range of the remote control decreases.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color.

• If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

• Do not throw away batteries with general house waste; dispose of them correctly in accordance with your local regulations.

• If the remote control is without batteries for more than 2 minutes, or if exhausted batteries remain in the remote control, the contents of the memory may be cleared. When the memory is cleared, insert new batteries and set up the remote control code.

Using the remote control

The remote control transmits a directional infrared ray. Be sure to aim the remote control directly at the remote control sensor on this unit during operation.

30º 30º

a Infrared window

Outputs infrared control signals. Aim this window at the component you want to operate.

• To set the remote control codes for other components, see page 39.

Notes

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types of

conditions:

– places of high humidity, such as near a bath – places of high temperature, such as near a heater or stove – places of extremely low temperatures – dusty places

• To set the remote control codes for other components, see page 39.

Approximately 6 m (20 ft)

8 En

Page 13

Connections

Placing speakers

The speaker layout below shows the speaker setting we recommend. You can use it to enjoy CINEMA DSP and multi-channel audio sources.

30˚

60˚

80˚

Front left and right speakers (FL and FR)

The front speakers are used for the main source sound plus effect sounds. Place these speakers at an equal distance from the ideal listening position. The distance of each speaker from each side of the video monitor should be the same.

Center speaker (C)

The center speaker is for the center channel sounds (dialog, vocals, etc.). If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system.

Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround sounds.

Subwoofer (SW)

The use of a subwoofer with a built-in amplifier, such as the Yamaha Active Servo Processing Subwoofer System, is effective not only for reinforcing bass frequencies from any or all channels, but also for high fidelity sound reproduction of the LFE (low-frequency effect) channel included in Dolby Digital and DTS sources. The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce wall reflections.

Connecting speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, this unit cannot reproduce the input sources accurately.

Caution

• Use speakers with the specified impedance shown on

the rear panel of this unit.

• Before connecting the speakers, make sure that this

the AC power plug is disconnected from the AC wall outlet.

• Do not let the bare speakers wires touch each other or

do not let them touch any metal part of this unit. This could damage this unit and/or speakers.

• Use magnetically shielded speakers. If this type of

speaker still creates interference with the monitor, place the speakers away from the monitor.

• If you are to use 6-ohm speakers, be sure to set “SP

IMP.” to “6ΩMIN” before using this unit. See page 40 for details on setting “SP IMP.”

■ 5.1-channel speaker connection

DTV/CBL

HDMI

VIDEO

MONITOR

DVR

OUT

AUDIO OUTPUT

L DVR CD

OUT

ANTENNA

GND

UNBAL.

OUT

MD/

(REC)

(PLAY)

CD-R

SURROUND CENTER FRONT B

SUB

WOOFER

SPEAKERS

a b

LRLR

FRONT A

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

English

9 En

Page 14

Connections

Speakers Jacks on this unit

a Front speaker (A) Right* FRONT A (R)

b Front speaker (A) Left* FRONT A (L)

c Surround speaker Right SURROUND (R)

d Surround speaker Left SURROUND (L)

e Center speaker CENTER

f Front speaker (B) Right* FRONT B (R)

g Front speaker (B) Left* FRONT B (L)

h Subwoofer SUBWOOFER

* You can select the front speaker set from Front speakers (A) and Front

speakers (B) by pressing CSPEAKERS repeatedly. See page 18 for details.

■ Connect speaker cables to each speaker

Cables are colored or shaped differently, perhaps with a stripe, groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of your speaker. Connect the plain cable to the “–” (black) terminals.

■ Connecting to the FRONT A terminals

Red: positive (+)

Black: negative (–)

1 Loosen the knob.

2 Insert the bare end of the speaker wire into

the slit on the terminal.

3 Tighten the knob to secure the wire.

Connecting the banana plug (except Europe, Russia, Korea, and Asia models)

The banana plug is a single-pole electrical connector widely used to terminate speaker cables. First, tighten the knob and then insert the banana plug connector into the end of the corresponding terminal.

Banana plug

■ Before connecting to the SPEAKERS terminal

A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a stripe, groove or ridges. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the plain cable to the “–” (black) terminals.

Remove approximately 10 mm (3/8”) of insulation from the end of each speaker cable and then twist the bare wires of the cable together to prevent short circuits.

10 mm (3/8”)

■ Connecting to the FRONT B, CENTER, and SURROUND terminals

Red: positive (+)

Black: negative (–)

1 Press down the tab.

2 Insert the bare end of the speaker wire into

the hole on the terminal.

3 Release the tab to secure the wire.

10 En

Page 15

Connections

Connecting video components

Information on jacks and cable plugs

Audio jacks and cable plugs

AUDI O

(White) (Red) (Orange)

Left and right

analog audio

cable plugs

DIGITAL AUDIO

COAXIAL

Coaxial

digital audio

cable plug

AUDIO jacks

For conventional analog audio signals transmitted via left and right analog audio cables. Connect red plugs to the right jacks and white plugs to the left jacks.

COAXIAL jack

For digital audio signals transmitted via coaxial digital audio cable.

OPTICAL jacks

For digital audio signals transmitted via optical digital audio cables.

Notes

• You can use the digital jacks to input PCM, Dolby Digital, and DTS

bitstreams. All digital input jacks are compatible with digital signals with up to 96 kHz of sampling frequency.

• This unit handles digital and analog signals independently. Thus audio

signals input at the digital jacks are not output at the analog AUDIO OUT (REC) jack.

Video jacks and cable plugs

VIDEO

COMPONENT VIDEO

Y PBP

DIGITAL AUDIO

OPTICAL

Optical

digital

audio cable

plug

VIDEO jacks

For conventional composite video signals transmitted via composite video cables.

COMPONENT VIDEO jacks

For component signals, separated into the luminance (Y) and chrominance (P

B, PR) video signals transmitted on

separate wires of component video cables.

Video signal flow for MONITOR OUT

Output

(MONITOR OUT)

COMPONENT VIDEO

VIDEO

Input

Information on HDMI™

Audio signals input at the HDMI jack are not output from any speaker terminals but output from the connected video monitor. To enjoy the sound from speakers connected to this unit,

– make an analog or digital connection besides the

HDMI connection (see page 13).

– mute the volume of the connected video monitor.

You can play back pictures by connecting your video monitor and video source component to this unit using HDMI connections. At that time, audio/video signals output from the connected component (such as DVD player etc.) are output to the connected video monitor only when this unit is turned on and set to the input source (DVD or DTV/ CBL). Furthermore, available audio/video signals depend on the specification of the connected video monitor. Refer to the instruction manual of each connected component.

■ HDMI jack and cable plug

HDMI

HDMI cable plug

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

(Yellow) (Blue) (Red)(Green)

Composite

video cable

plug

Component video cable

plugs

• We recommend using an HDMI cable shorter than 5 meters (16 feet)

with the HDMI logo printed on it.

• Use a conversion cable (HDMI jack ↔ DVI-D jack) to connect this unit

to other DVI components.

Using the AUDIO OUT REC jack

You can record the audio signal output at the AUDIO OUT (REC) jack by using the recording components.

English

Note

• Check the copyright laws in your country to record from CDs, radio, etc.

Recording of copyrighted material may infringe copyright laws.

11 En

Page 16

Connections

Connecting a TV monitor or projector

Make sure that this unit and other

components are unplugged from the

AC wall outlets.

Note

• If you turn off the video monitor connected to the HDMI OUT jack via a DVI connection, the connection may fail. In this case, the HDMI indicator

flashes irregularly.

(or projector)

Component

video in

PRPBY

HDMI

Audio

out

Video

HDMI

MONITOR

OUT

ANTENNA

GND

UNBAL.

OUTPUT

OUT

MD/

(REC)

(PLAY)

CD-R

WOOFER

DIGITAL INPUT

OPTICAL

COAXIAL

DOCK

DTV/ CBL

DVD

COMPONENT VIDEO

DVD DTV/CBL DVR

MULTI CH INPUT

FRONT CENTER

SURROUND

MONITOR

OUT

SUBWOOFER

DVDOUT DTV/CBL

VIDEO

DTV/CBL

DVD

DVD DTV/CBL DVR CD

DVR

OUT

AUDIO

OUT

Recommended connections Alternative connections

SUB

SURROUND C

12 En

Page 17

Connecting other components

Connections

Connecting audio and video components

This unit has three types of audio jacks, two types of video jacks and HDMI jacks. You can choose the connection method depending on the component to be connected.

■ Connecting example (connecting a DVD player)

DOCK

DIGITAL INPUT

OPTICAL

COAXIAL

Coaxial out

DTV/ CBL

DVD

COMPONENT VIDEO

DVD DTV/CBL DVR

FRONT CENTER

SURROUND

PRPBY

MONITOR

OUT

SUBWOOFER

Component out

DTV/CBL

DVD

DTV/CBL DVR CD

DVD

DVDOUT DTV/CBL

VIDEO

DVR

OUT

Audio out

Video out

MONITOR

AUDIOMULTI CH INPUT

OUT

HDMI out

ANTENNA

HDMI

GND

OUT

UNBAL.

MD/

(PLAY)

CD-R

OUTPUT

OUT (REC)

SUB

WOOFER

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

Recommended connections Alternative connections

■ Jacks used for audio and video connections

Recommended connections are indicated by (*). When connecting a recording component, you need to make additional connections for recording (signal transmission from this unit to the recording component).

• You can also use the VIDEO AUX jacks (see page 15) on the front panel

Make sure that this unit and other

components are unplugged from the

AC wall outlets.

Component Signal type Jacks on component Jacks on this unit

DVD player or Blu-ray Disc

Video HDMI out* HDMI (DVD)*

Component out COMPONENT VIDEO (DVD)

Video out (composite) VIDEO (DVD)

Audio Optical out* COAXIAL (DVD)*

Audio out (analog) AUDIO (DVD)

Set-top box Video HDMI out* HDMI (DTV/CBL)*

Component out COMPONENT VIDEO (DTV/CBL)

Video out (composite) VIDEO (DTV/CBL)

Audio Optical out* OPTICAL (DTV/CBL)*

Analog out (analog) AUDIO (DTV/CBL)

to connect an additional component.

• To confirm the positions of “jacks on this unit” in the following table,

refer to “Rear panel” in “Functional overview” on page 6.

INFORMATION APPENDIX

ADDITIONAL

English

13 En

Page 18

Connections

Component Signal type Jacks on component Jacks on this unit

DVD r ec order Video HDMI out* HDMI (DVR)*

Video out (composite) VIDEO (DVR IN)

Audio Audio out (analog)* AUDIO (IN (PLAY))*

Audio recording Audio in (analog)* AUDIO (OUT (REC))*

Video recording Video in (composite)* VIDEO (DVR OUT)*

CD player Audio Coaxial out* OPTICAL (CD)*

Audio Audio out (analog) AUDIO (CD)

MD or CD recorder Audio Audio out (analog)* AUDIO (IN (PLAY))*

Audio recording Audio in (analog)* AUDIO (OUT (REC))*

Notes

• Be sure to make the same type of video connections as those made for your TV if the video conversion is disabled. For example, if you connected your

TV to the VIDEO MONITOR OUT jack of this unit, connect other components to the VIDEO jacks.

• Check the copyright laws in your country to record from CDs, radio, etc. Recording of copyrighted material may infringe copyright laws.

• To make a digital connection to a component other than the default one assigned to each DIGITAL INPUT or DIGITAL OUTPUT jack, configure the

“INPUT ASSIGN” setting (see page 34).

• Only analog audio signals output at AUDIO OUT (REC) jack can be recorded using the recording components. Therefore Digital signals input at the

DIGITAL INPUT jacks or analog signals input at MULTI CH INPUT jacks can be output at the analog AUDIO OUT (REC) jack for recording.

Connecting a multi-format player or an external decoder

This unit is equipped with 6 additional input jacks (FRONT L/R, SURROUND L/R, CENTER and SUBWOOFER) for discrete multi-channel input from a multi-format player, external decoder or sound processor. Connect the output jacks on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to match the left and right output jacks to the left and right input jacks for the front and surround channels.

COAXIAL

MULTI CH INPUT

FRONT CENTER

DTV/

CBL

DVD

SURROUND

SUBWOOFER

Surround out

Front out

Multi-format player or

external decoder

DVD

Subwoofer out

DTV/CBL DV

Center out

Notes

• When you select the component connected to the MULTI CH INPUT

jacks as the input source (see page 34), this unit automatically turns off the digital sound field processor, and you cannot select sound field programs.

• This unit does not redirect signals input at the MULTI CH INPUT jacks

to accommodate for missing speakers. We recommend that you connect a

5.1-channel speaker system before using this feature.

• The source connected to the MULTI CH INPUT jacks on this unit cannot

be recorded.

Connecting a Yamaha iPod universal dock or Bluetooth Wireless Audio Receiver

This unit is equipped with the DOCK terminal on the rear panel that allows you to connect a Yamaha iPod universal dock (such as YDS-11, sold separately) or Bluetooth Wireless Audio Receiver (such as YBA-10, sold separately).

DOCK

DIGITAL INPUT

OPTICAL

DTV/

CBL

DVD

COAXIAL

Yamaha iPod universal dock

or Bluetooth Wireless Audio Receiver

14 En

Page 19

Connections

Using the VIDEO AUX jacks on the front panel

Use the VIDEO AUX jacks on the front panel to connect a game console or a video camera to this unit. To reproduce the source signals input at these jacks, select “V-AUX” as the input source.

Caution

Be sure to turn down the volume of this unit and other components before making connections.

Notes

• The audio signals input at the DOCK terminal on the rear panel take

priority over the ones input at the VIDEO AUX jacks.

• The audio signals input at the PORTABLE mini jack take priority over

the ones input at the AUDIO L/R jacks.

Connecting the FM and AM antennas

Both FM and AM indoor antennas are supplied with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals.

Notes

• The AM loop antenna should be placed away from this unit.

• A properly installed outdoor antenna provides clearer reception than an

indoor one. If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center about outdoor antennas.

• The AM loop antenna should always be connected, even if an outdoor

AM antenna is connected to this unit.

Outdoor AM antenna

Use a 5 to 10 m (16 to 32 ft) of vinyl-covered wire extended outdoors from a window.

AM loop antenna (supplied)

Connecting the wire of the AM loop antenna

Open the

lever

Insert Close the

lever

Assembling the supplied AM loop antenna

Note

• The types of the supplied AM loop antenna is different depending on the

models.

Connecting the power cable

Once all connections are complete, plug the power cable into the AC wall outlet.

Power cable

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

ANTENNA

DVR

MONITOR

N OUT

OUT

AUDIO OUT

DVR

OUT

Ground

For maximum safety and minimum

(PLAY)

UNBAL.

GND

OUT

MD/

(REC)

CD-R

SURR

interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

Indoor FM antenna (supplied)

To the AC wall outlet

Turning on and off the power

Turning on this unit

Press ASTANDBY/ON (or dPOWER) to turn on this unit.

• When you turn on this unit, there will be a 4 to 5-second delay before this

unit can reproduce sound.

Set this unit to the standby mode

Press ASTANDBY/ON (or cSTANDBY) to turn off this unit.

Note

• In the standby mode, this unit consumes a small amount of power in

order to receive infrared signals from the remote control.

15 En

English

Page 20

Basic setup

The “BASIC SETUP” feature is a useful way to set up your system quickly and with minimal effort.

Notes

• Make sure that you disconnect your headphones from this unit.

• If you wish to configure this unit manually using more precise

adjustments, use the detailed parameters in “SOUND MENU” (see page 32).

• Altering any parameters in “BASIC SETUP” resets all parameters

manually adjusted in “SOUND MENU” (see page 32).

• Initial settings are indicated by (*) in the following each parameters.

• Press nRETURN on the remote control to return to the previous menu

level.

1 Press hAMP on the remote control.

2 Press kMENU.

“BASIC SETUP” appears on the front panel display.

3 Press lENTER to enter “BASIC SETUP.”

“ROOM: S M L” appears on the front panel display.

4 Press ll / h to select the desired setting.

Select the size of the room where you have installed your speakers. The room sizes are defined as follows:

Choice Approximate Size of the room

S 16 x 13 ft, 200 ft2 (4.8 x 4.0 m, 20 m2) M* 20 x 16 ft, 300 ft2 (6.3 x 5.0 m, 30 m2) L 26 x 19 ft, 450 ft2 (7.9 x 5.8 m, 45 m2)

5 Press ln to select “SUBWOOFER” and then

ll / h to select the desired setting.

“SUBWOOFER” and the current setting appear on the front panel display.

Choice Condition

YES* When you have a subwoofer in your system. NONE When you do not have a subwoofer in your

system.

6 Press ln to select “SPEAKERS” and then

ll / h to select the number of speakers

connected to this unit.

“SPEAKERS” and the current setting appear on the front panel display.

Choice Display Speakers

2spk Front L/R

3spk Front L/R Center

4spk Front L/R, Surround L/R

5spk* Front L/R, Center, Surround L/R

LCR

SL SR

LCR

SL SR

7 Press ln to select “SET” and then ll / h

to select the desired settings.

“SET” and “CANCEL” appear on the front panel display.

Choice Function

SET Applies the settings you made. CANCEL* Cancels the setup procedure without making

any changes.

• You can also press kMENU to cancel the setup procedure.

8 Press lENTER to confirm your selection.

If you selected “SET” in step 7, each speaker outputs a test tone twice in turn. “CHECK:TestTone” appears on the front panel display for a few seconds and then “CHECK OK?” appears on the front panel display.

• Check the speaker connections (see page 9) and adjust the

“SPEAKERS” settings back in step 6, if necessary.

• The indicator of the speaker currently outputting the test tone

flashes on the front panel display.

9 Press ll / h to select the desired settings.

Choice Function

YES* Completes the setup procedure if the test tone

levels from each speaker were satisfactory.

NO Proceeds to the speaker level adjustment menu

to balance the output level of each speaker.

10 Press lENTER to confirm your selection.

• If you selected “YES” in step 9, the setup

procedure is completed and then display returns to the top set menu display. Press kMENU to exit from “BASIC SETUP.”

• If you selected “NO” in step 9, the front speaker

level adjustment display appears on the front panel display.

11 Press lk / n to select a speaker and then

ll / h to adjust the balance.

The selected speaker and the front left speaker (or the surround left speaker) output a test tone in turn.

• Press lh to increase the value.

• Press ll to decrease the value.

■ The balance between speakers you can adjust in each item is defined as follows.

Choice Adjusted balance between speakers

FR the front left and right speakers C the front left and center speakers SL the front left and surround left speakers SR the surround left and surround right speakers SWFR the front left speaker and the subwoofer

Note

• The available speaker channels differ depending on the setting of the

speakers.

12 Press kMENU to exit from “BASIC SETUP.”

16 En

Page 21

BASIC OPERATION

Playback

Caution

Extreme caution should be exercised when you play back CDs encoded in DTS. If you play back a CD encoded in DTS on a DTS-incompatible CD player, you will only hear some unwanted noise that may damage your speakers. Check whether your CD player supports CDs encoded in DTS. Also, check the sound output level of your CD player before you play back a CD encoded in DTS.

Basic procedure

1 Turn o n ex t er n al c omponents (TV, DVD

player, etc.) connected to this unit.

2 Press CSPEAKERS repeatedly to select the

front speakers you want to use.

The respective speaker indicators lights up on the front panel display.

3 Press NINPUT l / h repeatedly (or press

one of the input selector buttons (f)) to select the desired input source.

The name of the currently selected input source appears on the front panel display for a few seconds.

5 Rotate PVOLUME (or press mVOLUME +/–)

to adjust the volume to the desired output level.

• See page 19 to adjust the level of each speaker.

• This does not affect the AUDIO OUT (REC) level.

• You can set the initial volume level and maximum volume level

(see page 34).

6 Press LPROGRAM l / h (or press hAMP

and then qPROG l / h) repeatedly to select the desired sound field program.

The name of the selected sound field program appears on the front panel display. See page 21 for details about sound field programs.

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

Available input source

DVR DVD CD

V-AUX DTV/CBL

MD/CD-R

TUNER

INPUT:DVD

Currently selected input source

4 Start playback on the selected component or

select a broadcast station.

Notes

• Refer to the operating instructions for the source component.

• See page 27 for details about FM or AM tuning instructions.

• To adjust the level of each speaker, see page 19.

Movie Dramatic

Currently selected surround field program

Notes

• Choose a sound field program based on your listening preference, not

merely on the name of the program.

• When you select an input source, this unit automatically selects the last

sound field program used with the corresponding input source.

• Sound field programs cannot be selected when the component connected

to the MULTI CH INPUT jacks is selected as the input source (see page 18).

• When PCM signals with a sampling frequency higher than 48 kHz are

input, this unit is automatically set to the “STRAIGHT” mode (see page 26).

• To display information about the currently selected input source on the

front panel display, see page 20 for details.

INFORMATION APPENDIX

ADDITIONAL

English

17 En

Page 22

Playback

Guide to contents

When you want... See page

Adjust the tonal quality of the front speakers

Edit parameters of sound field programs

Enjoy the sources which have wide dynamic range at night

Use headphones 19

Select a decoder to play back sources with

Set this unit to the standby mode automatically

Additional operations

Using input setting features

Use the following features to select input jack or input source.

■ Selecting the front speaker set

■ Selecting the component connected to the

MULTI CH INPUT jacks as the input source

Use this feature to select the component connected to the MULTI CH INPUT jacks (see page 14) as the input source.

Press NINPUT l / h repeatedly (or press hAMP and then press vMULTI CH IN) to select “MULTI CH.”

“MULTI CH” appears on the front panel display.

• You can configure the multi channel input settings in “MULTI CH” (see

page 14).

Notes

• Sound field programs, or the night listening mode, etc. cannot be selected

when “MULTI CH” is selected as the input source.

• When headphones are used, signals are output only from the front left

and right channels.

■ Selecting audio input jacks (AUDIO SELECT)

Use this feature (audio input jack select) to switch the input jack assigned to an input source when two or more jacks are assigned to an input source.

• We recommend that you set the audio input jack select to “AUTO” in

most cases.

• You can adjust the default audio input jack select of this unit by using

“AUDIO SELECT” in “OPTION MENU” (see page 36).

Press CSPEAKERS repeatedly change the active front speaker set that is connected to the FRONT A or FRONT B speaker terminals or turn off the front speakers.

The active front speaker set changes as follows:

FRONT A FRONT B

OFF

Note

• Turn off the volume level of this unit before you switch the front speaker

setting.

■ Using the Zone B feature

When you set “FRONT B” to “ZONE B” (see page 32), you can use the speakers connected to FRONT B speaker terminals in another room (Zone B).

Press CSPEAKERS on the front panel repeatedly to turn on or off the Zone B speakers.

When you activate the Zone B speakers, all the speakers in the main room are muted.

Notes

• You cannot activate both the main room and Zone B speakers

simultaneously.

• If you select CINEMA DSP sound field program and activate the Zone B

speakers, Virtual CINEMA DSP is activated automatically (see page 26).

1 Press NINPUT l / h repeatedly (or press

one of the input selector buttons (f)) to select the desired input source.

2 Press hAMP and then wAUDIO SEL

repeatedly to select the desired Audio input jack select setting.

DVR DVD CD

V-AUX DTV/CBL

MD/CD-R

TUNER

A.SEL:AUTO

Audio input jack select setting

Choice Function

AUTO Automatically selects input signals in

the following order:

(1) Digital signals

(2) Analog signals

ANALOG Selects only analog signals. If no

analog signals are input, no sound is

output.

• You can configure the audio input jack select setting in “AUDIO

SELECT.”

Note

• This feature is not available if no digital input jack is assigned to

the selected input source in “INPUT ASSIGN” (see page 34).

18 En

Page 23

Playback

Using audio features

Use the following features to adjust the audio output or speaker level.

■ Muting the audio output

Press eMUTE on the remote control to mute the audio output. Press eMUTE again to resume the audio output.

• You can also rotate PVOLUME (or press mVOLUME +/–) to

resume the audio output.

• You can configure the muting level by using “MUTE TYP.” in “SOUND

MENU” (see page 34).

• The MUTE indicator flashes on the front panel display when the audio

output is muted and disappears from the front panel display when the audio output is resumed.

■ Adjusting the tonal quality

Use this feature to adjust the balance of bass and treble for the front left and right speaker channels.

Press KTONE CONTROL repeatedly to select “BASS” or “TREBLE” and then press LPROGRAM l / h to adjust the corresponding frequency response level.

Control range: –10 to +10 dB Each choice is defined as follows.

Choice Function

BASS Adjusts the low-frequency response.

TREBLE Adjusts the high-frequency response.

Notes

• Speaker and headphone adjustments are stored independently.

• If you increase or decrease the high-frequency or low-frequency sound to

an extreme level, the tonal quality of the surround speakers may not match that of the front left and right speakers.

• This does not affect recorded material.

■ Adjusting the speaker level

You can adjust the output level of each speaker while listening to a music source. This is also possible when playing sources input at the MULTI CH INPUT jacks.

Note

• This operation will override the level adjustment made in “SP LEVEL”

(see page 33).

1 Press hAMP and then press jBAND

LEVEL TITLE repeatedly to select the

speaker you want to adjust.

Choice Description

FRONT L Front left speaker

FRONT R Front right speaker

CENTER Center speaker

SWFR Subwoofer

SUR.L Surround left speaker

SUR.R Surround right speaker

• Once you press jBAND LEVEL TITLE on the remote

control, you can also select the speaker by pressing lk / n.

• The available speaker channels differ depending on the speaker

settings.

2 Press ll / h on the remote control (or

press FPRESET/TUNING l / h) to adjust the speaker output level.

Control range: –10.0 dB to +10.0 dB

Using optional features

Use the following features to utilize various useful functions equipped on this unit.

■ Using your headphones

Connect a pair of headphones with a stereo analog audio cable plug to the PHONES jack on the front panel.

• When you select a sound field program, SILENT CINEMA mode is

automatically activated (see page 26).

Notes

• When you connect headphones, no signals are output at the speaker

terminals.

• All Dolby Digital and DTS audio signals are mixed down to the left and

right headphone channels.

■ Selecting the night listening mode

The night listening modes are designed to improve listenability at lower volumes or at night.

1 Press ONIGHT (or press hAMP and then

uNIGHT) repeatedly to select

“NIGHT:CINEMA” or “NIGHT:MUSIC.”

Each choice is defined as follows.

Choice Function

NIGHT:CINEMA Narrows the dynamic range of film

soundtracks and makes dialog easier to

hear at lower volumes.

NIGHT:MUSIC Preserves ease-of-listening for all

sounds.

NIGHT OFF Disables this feature.

• When a night listening mode is selected, the NIGHT indicator

lights up on the front panel display.

2 Press ll / h to adjust the effect level while

“NIGHT:CINEMA” or “NIGHT:MUSIC” is displayed on the front panel display.

Each choice is defined as follows.

Choice Function

MIN Slightly lowers the effect level.

MID* Moderately lowers the effect level.

MAX Considerably lowers the effect level.

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

English

19 En

Page 24

Playback

• “NIGHT:CINEMA” and “NIGHT:MUSIC” adjustments are stored

independently.

Notes

• You cannot use the night listening modes in the following cases: – when the component connected to the MULTI CH INPUT jacks is

selected as the input source.

– when headphones are connected to the PHONES jack. – when the sampling frequency of the input sources are higher than 48

kHz.

• The effect of night listening modes may vary depending on the input source and surround sound settings you use.

■ Displaying the input source information

(SIGNAL INFO)

You can display the format, sampling frequency, channel, bit rate and flag data of the current input signal.

1 Press hAMP and then press kMENU on

the remote control.

“BASIC SETUP” appears on the front panel display.

;BASIC SETUP

2 Press lk / n repeatedly to select “SIGNAL

INFO” and then press lENTER.

3 Press lk / n to switch the displayed

information.

The following information about the input source appears on the front panel display.

Choice Description

FORMAT Signal format.

SAMPLING The number of samples per second

taken from a continuous signal to

make discrete signals.

CHANNEL The number of source channels in the

input signal (front/surround/LFE).

BITRATE The number of bits passing a given

point per second.

FLAG Flag data encoded in DTS, Dolby

Digital, or PCM signals that cue this

unit to automatically switch decoders.

■ Using the sleep timer

Use this feature to automatically set this unit to the standby mode after a certain amount of time. The sleep timer is useful when you are going to sleep while this unit is playing or recording from a source.

Press hAMP and then press xSLEEP repeatedly to set the amount of time.

The sleep timer setting changes as follows.

SLEEP 120min SLEEP 90min

SLEEP 60minSLEEP 30minSLEEP OFF

Once the sleep timer is set, the SLEEP indicator lights up on the front panel display, and the display returns to the selected sound field program.

To cancel the sleep timer

Press xSLEEP on the remote control repeatedly to select “SLEEP OFF.”

• If you set the main zone to the standby mode, the sleep timer is

automatically canceled.

■ Playing video sources in the background

You can combine a video image from a video source with sound from an audio source. For example, you can enjoy listening to classical music while viewing beautiful scenery from the video source on the video monitor.

Press the input selector buttons (f) on the remote control to select a video source and then an audio source.

CD MD/CD-R TUNER

DVD

DTV/CBL DVR

DVD

V-AUX/DOCK

DVD

DTV/CBL DVR

DVD

V-AUX/DOCK

Audio sources

Video sources

4 Press kMENU on the remote control again

to exit from “SET MENU.”

20 En

MULTI CH IN

Audio sources

Page 25

Selecting the SCENE templates

Just by pressing one SCENE button, you can recall your favorite input source and sound field program according to the SCENE template that has been assigned to the SCENE button. The SCENE templates are built combinations of input sources and sound field programs.

This unit is equipped with 13 preset SCENE templates for various situations. The following SCENE templates are assigned to respective SCENE buttons in the default settings.

Default SCENE

button

SCENE 1

SCENE 2

SCENE 3

SCENE 4

The name of the SCENE template and

its description

DVD Viewing

– input source: DVD – sound field program: STRAIGHT

For when you want to enjoy a DVD

playback.

Disc Listening

– input source: DVD – sound field program: 5ch Stereo

For when you want to listen to a music disc

from the connected DVD player as the

background music for this room.

TV Viewing *1

– input source: DTV/CBL – sound field program: STRAIGHT

For when you want to watch a TV program.

Radio Listening *2, *3, *4

– input source: TUNER – sound field program: Music Enh. 5ch

For when you want to listen to a music

program from the FM radio station.

Notes

*1 You must connect a cable TV or a satellite tuner to this unit in advance.

See page 13 for details.

*2 You need to connect the supplied FM and AM antennas to this unit in

advance. See page 15 for details.

*3 You have to tune into the desired radio station. See pages 27 to 28 for

the tuning information.

*4 To achieve the best possible reception, orient the connected AM loop

antenna, or adjust the position of the end of the indoor FM antenna.

Selecting the desired SCENE template

If you want to use other SCENE templates, you can select the desired SCENE templates from the SCENE template library and assign the templates to the selected SCENE buttons on the front panel and the remote control.

Select the desired SCENE template

Assign the

SCENE template

to the SCENE

SCENE template library

(Image)

button

1 Press and hold the desired JSCENE (or

iSCENE) button for 3 seconds.

The MEMORY indicator on the front panel starts to flash, and the name of currently assigned SCENE template appears on the front panel display.

DVD Viewing

2 Press NINPUT l / h (or press hAMP and

then ll / h) to select the desired template.

DVD Movie View

3 Press the JSCENE (or iSCENE) button

again to confirm the selection.

The MEMORY indicator stops flashing and the select SCENE template is assigned to the button.

• To cancel the procedure, press hAMP and then nRETURN.

Note

• Once the desired SCENE templates are assigned to the corresponding

SCENE buttons, you may need to set the input source of the SCENE template on the remote control. See page 24 for details.

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

21 En

English

Page 26

Selecting the SCENE templates

Which SCENE template would you like to select?

The following tables indicate preset SCENE template descriptions. Select the corresponding SCENE templates for the desired source. The illustrations of the SCENE button in the following table indicate that the SCENE templates in those cells are assigned to the SCENE buttons, respectively. You can also create your original SCENE templates by editing the preset SCENE templates. See page 23 for details.

■ Video sources (DVD video, Recorded video)

SCENE template Input source Playback mode Features

DVD Viewing DVD STRAIGHT

DVD Movie Viewing DVD Movie Dramatic

DVD Live Viewing DVD Pop/Rock

DVR Viewing DVR Movie Dramatic

■ Music discs (CD, SA-CD or DVD-Audio)

SCENE template Input source Playback mode Features

Music Disc Listening DVD 2ch Stereo

Disc Listening DVD 5ch Stereo

CD Listening CD 5ch Stereo

CD Music Listening CD 2ch Stereo

Select this SCENE template when you play back

general contents on your DVD player.

Select this SCENE template when you play back

movies on your DVD player.

Select this SCENE template when you enjoy music

live video on your DVD player.

Select this SCENE template when you play back

movies on your digital video recorder.

Select this SCENE template when you play back

music discs on your DVD player.

Select this SCENE template when you play back

music sources as the back ground music on your

DVD player.

Select this SCENE template when you play back

music source as the back ground music on your CD

player.

Select this SCENE template when you play back

music discs on your CD player.

■ Radio programs

SCENE template Input source Playback mode Features

Radio Listening TUNER Music Enh. 5ch

■ iPod or Bluetooth component

SCENE template Input source Playback mode Features

Dock Listening DOCK Music Enh. 5ch

■ TV programs

SCENE template Input source Playback mode Features

TV Viewing DTV/CBL STRAIGHT

TV Sports Viewing DTV/CBL TV Sports

22 En

Select this SCENE template when you enjoy FM or

AM radio programs.

Select this SCENE template when you play back

music on your iPod stationed in a Yamaha iPod

universal dock or Bluetooth component that is

connected to the Bluetooth receiver.

Select this SCENE template when you enjoy TV

programs.

Select this SCENE template when you enjoy sports

programs on TV.

Page 27

Selecting the SCENE templates

■ Video games

SCENE template Input source Playback mode Features

Game Playing V-AUX Game

Select this SCENE template when you play video

games.

Note

• When an iPod is connected to the Yamaha iPod universal dock or a Bluetooth component is connected to the Bluetooth receiver, this unit plays back the

audio sources input at the DOCK terminal.

INTRODUCTION

Creating your original SCENE templates

You can create your original SCENE templates for each SCENE button. Refer to the preset 13 SCENE templates to create the original SCENE templates.

Customizing the preset SCENE templates

Use this feature to customize the preset SCENE templates.

Select the desired SCENE

template

SCENE template library

(Image)

1 Press and hold the desired iSCENE button

for 3 seconds and then press hAMP.

The MEMORY indicator on the front panel starts to flash.

3 seconds

Create an original SCENE

template

: DVD

INPUT

: DVD Viewing

SCENE

Assign the SCENE

template to the SCENE

button

AMP

SCENE : DVD Viewing

2 Press lk / n to select the desired parameter

of the SCENE template and then ll / h to select the desired value of the selected parameter.

You can adjust the following parameters for a SCENE template:

• The input source component

• The active sound field programs or STRAIGHT

mode

• The night listening mode setting (see page 19) – SYSTEM: Keeps the current night listening

mode.

– CINEMA: Sets the night listening mode to the

CINEMA mode.

– MUSIC: Sets the night listening mode to the

MUSIC mode.

3 Press the iSCENE button again to confirm

the edit.

• An asterisk mark (*) appears by the name of the original SCENE

template.

• To cancel the procedure, press hAMP and then nRETURN.

Notes

• After changing the assignment of the SCENE template to the iSCENE

buttons, you may need to set the input source of the SCENE template on the remote control. See page 24 for details.

• You can create a customized SCENE template for each iSCENE

button, and if you create another customized SCENE template, this unit overwrites the old customized SCENE template with the new one.

• The customized SCENE template is only available for the assigned

iSCENE button.

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

Note

• When the SCENE template you want to customize is not assigned

to any of the iSCENE button, press ll / h repeatedly to recall the desired SCENE template (see page 21).

English

23 En

Page 28

Selecting the SCENE templates

Using remote control on the SCENE feature

Controlling the input source components in the SCENE mode

You can operate both this unit and the input source component by using the remote control. You must set the appropriate remote control code for each input source in advance (see page 39).

1 Press the desired iSCENE button on the

remote control.

2 Press the desired buttons in the * area below

to control the input source component of the selected SCENE template.

POWER

STANDBY

POWER

AVTV

A B C

MUTE

CD MD/CD-R TUNER

DVD

V-AUX/DOCK

AMP

BAND LEVEL

TITLE

RETURN

REC

DTV/CBL DVR

D E

TV INPUT

SCENE

ENTER

TV CH

TV VOL

TV MUTE

SCENE buttons

4321

VOLUME

DISPLAY

l PROG h

SUR. DECODE

ENHANCER

4321

NIGHT

STRAIGHT

MULTI CH IN AUDIO SEL

SLEEP

ENT

10709

Note

• These buttons control the input source component. See page 37 for

details of the function of each button.

Setting input source of the customized SCENE template on the remote control

If you customize the input source of the selected SCENE template, you must set the input source of the SCENE template on the remote control to operate the input source component correctly.

Press and hold the iSCENE button and the desired input selector button (f) for 3 seconds.

• Press the iSCENE button again to operate the input source

component.

24 En

Page 29

Sound field programs

This unit is equipped with a variety of precise digital decoders that allow you to enjoy multi-channel playback from almost any stereo or multi-channel sound source. This unit is also equipped with a Yamaha digital sound field processing (DSP) chip containing several sound field programs which you can use to enhance your playback experience.

Selecting sound field programs

Press LPROGRAM l / h (or press hAMP and then press qPROG l / h repeatedly).

Notes

• When you select an input source, this unit automatically selects the last

sound field program used with corresponding input source.

• Sound field programs cannot be selected when the component connected

to the MULTI CH INPUT jacks is selected as the input source (see page 18).

• When PCM signals with a sampling frequency higher than 48 kHz are

input, this unit is automatically set to the “STRAIGHT” mode (see page 26).

• Choose a sound field program based on your listening preference, not

merely on the name of the program itself.

• You can select “Music Enh. 2ch” and “Music Enh. 5ch” by pressing

rENHANCER repeatedly.

The name of the selected sound field program appears on the front panel display.

Sound field program descriptions

• Select a sound field program based on your listening preference, not merely on the name of the program, etc.

• The available sound field parameters differ depending on the settings of the speakers.

Category Program Features

Pop/Rock CINEMA DSP processing. This program presents an image of pop, rock, or jazz live concert. The

sound field reproduces the spaciousness of a massive pavilion with an emphasis on the vividness of

vocals on the stage and solo instruments and the beats of rhythm instruments.

MUSIC

ENTERTAIN

MOVIE

STEREO

ENHANCER

Hall CINEMA DSP processing. This sound field is suitable for classic and orchestral music. The

program uses data collected in a large concert hall in Munich. You can enjoy delicate and beautiful

reverberation and a majestic atmosphere.

Jazz CINEMA DSP processing. The sound field is suitable for jazz and fusion music.

It uses data collected in a famous jazz club in New York. You can enjoy clear reverberation.

Game CINEMA DSP processing. You can enjoy dynamic and thrilling sound effects as you play games.

The program lets you feel the depth and three-dimensional surrounding sounds of the field where

you are playing, and offers cinema-like surrounding sound effects for the scenes of movies.

TV Sports CINEMA DSP processing. You can enjoy sports relays broadcast in stereo and variety shows with

a live sound environment. For sports relays, the voices of commentators and announcers come

clearly from the center; the cheers and atmosphere in the stadium spread around within a

comfortable range, and you can feel like as if you are in the stadium.

Movie Spacious CINEMA DSP processing. The sound field is suitable for movies with an emphasis on spectacular

sound effects, and is a perfect fit with a wide screen. The program reproduces a wide dynamic

range from minimum sound effects to powerful sounds.

Movie Dramatic CINEMA DSP processing. This sound field is also suitable for movies with an emphasis on three-

dimensional sound effects. It restrains reverberation to an moderate extent, but reproduces sound

effects and background music in a soft, three-dimensional manner with clarity and center

orientation of voices as pivots.

2ch Stereo Downmixes multi-channel sources to 2 channel or plays back 2-channel sources as they are.

5ch Stereo CINEMA DSP processing. Using this program increases the listening position range. This is a

sound field suitable for background music at parties.

Music Enh. 2ch Music Enh. 5ch

Select these programs to play back compression artifacts (such as the MP3 format) in 2-channel or

5-channel stereo. This program enhances your listening experience by regenerating the missing

harmonics in a compression artifact.

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

English

25 En

Page 30

Sound field programs

■ Selecting decoders for 2-channel sources (surround decode mode)

Signals input from 2-channel sources can also be played back on multi-channels.

Press hAMP and then press sSUR. DECODE repeatedly to select a decoder.

You can select from the following decoders depending on the type of source you are playing and your personal preference.

STANDARD Function

PRO LOGIC Dolby Pro Logic processing for any sources PLII Movie Dolby Pro Logic II processing for movie

sources

PLII Music Dolby Pro Logic II processing for music

sources

PLII Game Dolby Pro Logic II processing for game

sources

■ Editing sound field parameters

Although you can enjoy good quality sound with the factory default parameters, you can change some of the parameters to better suit the input source or your listening room.

1 While listening to a source, press hAMP

and then press lk / n to select desired parameter.

2 Press ll / h to change the parameter

value.

Note

• You cannot change parameter values when “MEM.GUARD” in

“OPTION MENU” is set to “ON” (see page 35).

• Initial settings are indicated by (*) in the following each parameter.

For Pop/Rock, Hall, Jazz, Game, TV Sports, Movie Spacious and Movie Dramatic:

DSP level DSP LEVEL

Function: Adjusts the effect level.

Choices: MIN, MID*, MAX

For PRO LOGIC II Music:

Panorama PANORAMA

Function: Sends stereo signals to the surround

speakers as well as the front speakers for a

wraparound effect.

Choices: OFF*, ON

Dimension DIMENSION

Function: Gradually adjusts the sound field either

towards the front or towards the rear.

Control range: –3 (towards the rear) to +3 (towards the

front), initial setting is STD (standard).

Center width CT WIDTH

Function: Adjusts the center image from all three front

speakers to varying degrees. A larger value

adjusts the center image towards the front

left and right speakers.

Control range: 0 (center channel sound is output only from

center speaker) to 7 (center channel sound is

output only from front left and right

speakers), initial setting is 3.

For Music Enh. 2ch and Music Enh. 5ch

Effect level

Function: Adjusts the effect level.

Choices: LOW, HIGH*

■ Using sound field programs without surround speakers (Virtual CINEMA DSP)

Virtual CINEMA DSP allows you to enjoy the CINEMA DSP sound field programs without surround speakers. When you set “SUR. L/R” to “NONE” (see page 33), Virtual CINEMA DSP is activated automatically whenever you select a CINEMA DSP sound field program (see page 25).

■ Enjoying multi-channel sources and sound field programs with headphones (SILENT CINEMA)

SILENT CINEMA allows you to enjoy multi-channel music or movie sound through ordinary headphones. SILENT CINEMA is activated automatically whenever you connect headphones to the PHONES jack while listening to CINEMA DSP sound field programs (see page 25).

• When it is activated, the SILENT CINEMA indicator lights up on the

front panel display.

■ Enjoying unprocessed input sources (Straight decoding mode)

When this unit is in the “STRAIGHT” mode, 2-channel stereo sources are output from only the front left and right speakers. Multi-channel sources are decoded straight into the appropriate channels without any additional effect processing.

Press MSTRAIGHT (or press hAMP and then tSTRAIGHT) to select “STRAIGHT.”

“STRAIGHT” appears on the front panel display.

To deactivate the “STRAIGHT” mode

Press MSTRAIGHT (or tSTRAIGHT) again so that “STRAIGHT” disappears from the front panel display.

26 En

Page 31

FM/AM tuning

Overview

You can use two tuning modes to tune into a desired FM/ AM station:

■ Frequency tuning mode

You can search or specify the frequency of the desired FM/AM station automatically or manually (see “FM/AM tuning operations” on this page).

■ Preset tuning mode

You can preset the desired FM/AM station in advance, and then recall the station by specifying the preset group and number (see “Selecting preset stations” on page 28).

Note

• Orient the connected AM loop antenna, or adjust the position of the end

of the indoor FM antenna for the best reception.

FM/AM tuning operations

1 Press NINPUT l / h repeatedly so that

“TUNER” is displayed on the front panel display.

2 Press GBAND to select the reception band

(FM or AM).

3 To search the station automatically, press

ITUNING AUTO/MAN’L so that the AUTO indicator lights up on the front panel display. To search the station manually, press ITUNING AUTO/MAN’L again so that the AUTO indicator disappears from the front panel display.

Lights up during automatic tuning

AUTO

No colon (:)

If a colon (:) appears on the front panel display, automatic/manual tuning is not possible. Press DEDIT PRESET/TUNING to turn the colon (:) off.

1440

kHz

4 To begin automatic tuning, press

FPRESET/TUNING l / h once. To tune into the desired station manually, press FPRESET/TUNING l / h repeatedly.

When this unit is tuned into a station, the TUNED indicator lights up and the frequency of the received station is shown on the front panel display.

Lights up

AUTO

TUNED

• To tune into a higher frequency, press

FPRESET/TUNING h.

• To tune into a lower frequency, press FPRESET/

TUNING l.

Note

• If the signal from the station you want to select is weak, tune into it

manually.

1530

kHz

Preset FM/AM stations

Use this feature to store up to 40 stations (A1 to E8: 8 preset station numbers in each of 5 preset station groups). Preset the desired stations to this unit by using the automatic or manual station preset.

Automatic station preset

You can use the automatic preset tuning feature to store up to 40 FM stations with strong signals in order.

1 Press NINPUT l / h repeatedly so that

“TUNER” is displayed on the front panel display.

2 Press GBAND to select “FM” as the

reception band.

3 Press and hold HMEMORY for more than 3

seconds.

The preset station number as well as the MEMORY and AUTO indicators flashes. After approximately 5 seconds, automatic presetting status from the current frequency and proceeds toward the higher frequencies.

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

Flashes

AUTO

MEMORY

A1:FM 87.5 MHz

Flashes

When automatic preset tuning is completed, the front panel display shows the frequency of the last preset station.

27 En

English

Page 32

FM/AM tuning

• You can select the preset station group and the preset station number

where the first received station will be stored by pressing EA/B/C/D/E and then FPRESET/TUNING l / h.

Notes

• Any stored station data existing under a preset station number is cleared

when you store a new station under the same preset station number.

• Only FM stations with sufficient signal strength are stored automatically

by automatic preset tuning. If the station you want to store is weak in signal strength, tune it manually and store it as described in “Manual station preset” on this page.

Manual station preset

Use this feature to store the FM or AM stations manually.

1 Tune into a station.

See page 27 for using instructions.

2 Press HMEMORY.

The MEMORY indicator flashes on the front panel display for approximately 30 seconds.

3 Press EA/B/C/D/E and FPRESET/TUNING

l / h repeatedly to select a preset station group and number (A1 to E8) while the MEMORY indicator is flashing.

Check that the colon (:) appears on the front panel display.

• To select a higher preset station group and number,

press FPRESET/TUNING h.

• To select a lower preset station group and number,

press FPRESET/TUNING l.

Flashes

TUNED

MEMORY

Preset station group and number

630

kHz

4 Press HMEMORY while the MEMORY

indicator is flashing.

The station band and frequency appear on the front panel display with the preset station group and number you have selected.

TUNED

The displayed station has been stored as C3.

Selecting preset stations

You can tune into any desired station simply by selecting the preset station group and number under which it is stored.

When performing this operation with the remote control, press fTUNER to select “TUNER” as the input source.

630

kHz

1 Press EA/B/C/D/E (or ll / h) repeatedly to

select the desired preset station group (A to E).

The preset station group letter appears on the front panel display and changes each time you press the button.

2 Press FPRESET/TUNING l / h (or lk /

n) to select the desired preset station

number (1 to 8).

The preset station group and number, along with station band and frequency, appear on the front panel display.

• You can select the desired preset station number (1 to 8) directly by

pressing the numeric buttons (y).

87.5

MHz

Exchanging preset stations

You can exchange the assignments of two preset stations between the two. The example below describes the procedure to exchange preset station “E1” and “A5.”

1 Select preset station “E1” using EA/B/C/D/E

and FPRESET/TUNING l / h.

See “Selecting preset stations” on this page.

2 Press and hold DEDIT PRESET/TUNING

for more than 3 seconds.

“E1” and the MEMORY indicator flash on the front panel display.

Flashes

MEMORY

Flashes

87.5

MHz

3 Select preset station “A5” using EA/B/C/D/E

and FPRESET/TUNING l / h.

“A5” and the MEMORY indicator flash on the front panel display. See “Selecting preset stations” on this page.

Flashes

MEMORY

Flashes

90.5

MHz

4 Press DEDIT PRESET/TUNING again.

“EXCHANGE E1-A5” appears on the front panel display and the assignments of the two preset stations are exchanged.

28 En

Page 33

Using iPod™

V-AUX/DOCK

MENUTITLE

ENTER

BAND LEVEL

DISPLAY

RETURN

REC

Once you have stationed your iPod in a Yamaha iPod universal dock (such as the YDS-11, sold separately) connected to the DOCK terminal of this unit (see page 14), you can enjoy playback of your iPod using the supplied remote control.

■ Supported iPod

iPod (Click Wheel, including iPod classic) iPod nano iPod mini iPod touch

■ Battery charge feature

Your iPod battery is automatically charged when your iPod is stationed in a Yamaha iPod universal dock connected to the DOCK terminal of this unit as long as this unit is turned on.

■ Stationing your iPod to the Yamaha iPod universal dock

Once you station your iPod to the Yamaha iPod universal dock, “iPod connected” and the DOCK indicator appears on the front panel display when “V-AUX” is selected as the input source.

Control and functions for iPod™

POWER

A B C

CD MD/CD-R TUNER

DVD

V-AUX/DOCK

AMP

BAND LEVEL

TITLE

RETURN

REC

POWER

AVTV

DTV/CBL DVR

D E

TV INPUT

SCENE

ENTER

STANDBY

TV MUTE

POWER

MUTE

TV CH

TV VOL

4321

VOLUME

DISPLAY

V-AUX/DOCK

Selects “V-AUX” or “DOCK” as the input source.

MENU/Cursor buttons (k / n / l / h) / ENTER

Navigates the menu of your iPod.

• Press kMENU or ll to move to the previous

menu level.

• Press lk / n to move to the upper/lower menu level.

• Press lENTER or lh to move to the subsequent

menu, start playback of the selected menu level, or change the selected setting.

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

l PROG h

SUR. DECODE

ENHANCER

4321

NIGHT

STRAIGHT

MULTI CH IN AUDIO SEL

SLEEP

ENT

10709

Playback control buttons

Navigates the menu of your iPod.

p/e: Play/pause s: Stop w / f: Search backward/forward b / a: Skip backward/forward

Notes

• Operations can be also done with the controls on your iPod. Refer to the instruction manuals of your iPod for the operations on your iPod.

• Some features may not be compatible depending on the model or the software version of your iPod.

• For a complete list of status messages that appear on the front panel display, see the “iPod” section in “Troubleshooting” on page 44.

29 En

INFORMATION APPENDIX

ADDITIONAL

English

Page 34

Using Bluetooth™ components

You can connect a Bluetooth Wireless Audio Receiver (such as YBA-10, sold separately) to the DOCK terminal of this unit and enjoy the music contents stored in your Bluetooth component (such as a portable music player) without wiring between this unit and the Bluetooth component. You need to perform “pairing” for the connected Bluetooth receiver and your Bluetooth component in advance.

Pairing the Bluetooth™ receiver and your Bluetooth™ component

Pairing must be performed when you use a Bluetooth component with the Bluetooth receiver connected to this unit for the first time or if the pairing data has been deleted. “Pairing” refers to the operation of registering a Bluetooth component for Bluetooth communications.

• You need to perform the pairing operation only when you use the

Bluetooth component with the Bluetooth receiver for the first time.

• You need to perform the pairing operations both on this unit and on the

Bluetooth component. If necessary, refer to operating instructions of the Bluetooth component.

There are two pairing methods: pairing by using “START PAIRING” in “SET MENU” and quick pairing.

■ Pairing by using “SET MENU”

Use this feature to perform pairing of this unit and the video monitor. Select “START PAIRING” in “INPUT MENU.” See page 36 for details.

■ Quick pairing

To ensure security, a time limit of 8 minutes is set for the pairing operation. You are recommended to read and fully understand all the instructions before starting.

1 Press hAMP and then press NINPUT l /

h repeatedly (or press fV-AUX/DOCK) to

select “V-AUX” as the input source.

5 Select the Bluetooth receiver in the

Bluetooth device list and then enter the pass key “0000” to the Bluetooth component.

When the pairing is completed successfully, “Completed” appears on the front panel display.

Note

• The Bluetooth Wireless Audio Receiver can be paired with up to eight

other components. When pairing is conducted successfully with a ninth component and the pairing data is registered, the pairing data for the least recently used other component is cleared.

Playback of the Bluetooth™ component

1 Press hAMP and then press NINPUT l /

h repeatedly (or press fV-AUX/DOCK) to

select “V-AUX” as the input source.

2 Start playback of your Bluetooth component.

When the connected Bluetooth receiver detects the Bluetooth component, “BT connected” and the DOCK indicator appears on the front panel display.

• When you press lENTER on the remote control, the connected

Bluetooth receiver searches and connect to the last connected Bluetooth component. If the Bluetooth receiver cannot find the Bluetooth component, “Not found” appears on the front panel display.

• To disconnect the Bluetooth receiver from the Bluetooth component,

press nRETURN.

2 Turn on the Bluetooth component you want

to pair with.

3 Press and hold GBAND (or jBAND LEVEL

TITLE) for 3 seconds.

Once the Bluetooth receiver starts pairing, “Searching...” appears for a moment. While the Bluetooth receiver is in the pairing mode, DOCK indicator flashes on the front panel display.

• To cancel the pairing, press GBAND (or jBAND LEVEL

TITLE) again.

Note

• If the Bluetooth receiver is not connected to the DOCK terminal of

this unit, “No BT adapter” appears on the front panel display.

4 Check that the Bluetooth component detects

the Bluetooth receiver.

If the Bluetooth component detects the Bluetooth receiver, “YBA-10 YAMAHA” (example) appears in the Bluetooth device list.

30 En

Page 35

ADVANCED OPERATION

Set menu

You can use the following parameters in the set menu to adjust a variety of system settings and customize the way this unit operates. Change the initial settings to reflect the needs of your listening environment.

Basic setup BASIC SETUP

Use this feature to automatically adjust speaker and system parameters (see page 16).

Manual setup MANUAL SETUP

Use this feature to manually adjust speaker and system parameters.

■ Sound menu 1 SOUND MENU

Use this menu to manually adjust any speaker settings, alter the quality and tone of the sound output by the system or compensate for video signal processing delays when using LCD monitors or projectors.

Parameter Features Page

A)SPEAKER SET Selects the size of each speaker, the speakers for low-frequency signal output, the crossover frequency,

and the location of the front speakers connected to the FRONT B terminals.

B)SP LEVEL Adjusts the output level of each speaker. 33

C)SP DISTANCE Adjusts the distance of each speaker. 33

D)CENTER GEQ Adjusts the tonal quality of the center speaker. 33

E)LFE LEVEL Adjusts the output level of the LFE channel for Dolby Digital or DTS signals. 34

F)D.RANGE Adjusts the dynamic range of Dolby Digital or DTS signals. 34

G)AUDIO SET Adjusts the muting level, audio delay settings, maximum volume level and initial volume level. 34

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

■ Input menu 2 INPUT MENU

Use this menu to manually reassign the input jacks, select the input mode or rename the input source.

Parameter Features Page

A)INPUT ASSIGN Assigns the input jacks on this unit according to the component to be used. 34

B)INPUT RENAME Changes the name of the input source. 34

C)VOLUME TRIM Adjusts the output volume of each jack. 35

D)DECODER MODE Selects the decoder mode for the sources connected to the DIGITAL INPUT jacks on the rear panel of

this unit.

E)MULTI CH SET Select the video source played in the background of the sources input from the MULTI CH INPUT jacks. 35

■ Option menu 3 OPTION MENU

Use this menu to manually adjust the optional system parameters.

Parameter Features Page

A)DISPLAY SET Adjusts the brightness of the front panel display. 35

B)MEMORY GUARD Locks sound field program parameters and other set menu settings. 35

C)AUDIO SELECT Designates the default audio input jack select setting mode for the input sources connected to the

DIGITAL INPUT jacks when you turn on the power of this unit.

D)PARAM. INI Sets all the parameters of the sound field programs to the initial factory settings. 36

E)BLUETOOTH Pairs the connected Bluetooth Wireless Audio Receiver (such as YBA-10, sold separately) with a

Bluetooth component (see page 30).

Signal information SIGNAL INFO

INFORMATION APPENDIX

ADDITIONAL

English

Use this feature to check audio signal information (see page 20).

31 En

Page 36

Set menu

Using set menu

Use the remote control to access and adjust each parameter.

• You can change the set menu parameters while this unit is reproducing

sound.

1 Press hAMP and then press k MENU on

the remote control.

“BASIC SETUP” appears on the front panel display.

2 Press lk / n to select “MANUAL SETUP.”

MANUAL SETUP

3 Press lENTER to enter “MANUAL SETUP.”

“1 SOUND MENU” appears on the front panel display.

1 SOUND MENU

4 Press lk / n repeatedly and then press

lENTER to select and enter the desired

menu.

The following menus appear on the front panel display as you press lk / n repeatedly.

1 SOUND MENU

Use this menu to manually adjust any speaker settings or compensate for video signal processing delays when using LCD monitors or projectors.

• Initial settings are indicated by (*) in this following each parameter.

Speaker settings A)SPEAKER SET

Use this feature to manually adjust any speaker settings.

■ FRONT B speaker setting FRONT B

Use this feature to select the location of the front speakers connected to the FRONT B terminals.

Choice Condition

FRONT* When FRONT B speakers are set in the main zone.

ZONE B When FRONT B speakers are set in another zone. This

setting mutes all the speakers in the main room when FRONT B is selected by CSPEAKERS.

Notes

• If you connect headphones to the PHONES jack on this unit, the sound is

output from both headphones and the FRONT B terminals while “FRONT B” is set to “ZONE B.”

• If a DSP program is selected when “FRONT B” is set to “ZONE B,” this

unit automatically enters the Virtual CINEMA DSP mode (see page 26).

Woofer diameter of a speaker is 16 cm (6.5 in) or larger: large Woofer diameter of a speaker is smaller than 16 cm (6.5 in): small

2 INPUT MENU

3 OPTION MENU

5 Press lk / n repeatedly and then press

lENTER to select and enter the desired

submenu.

• Repeat this step to navigate to and enter the items

you want to adjust.

• To return to the previous menu level, press

nRETURN.

6 Press lk / n to select the desired parameter

and then ll / h to change the parameter value.

• Press l h to increase the value.

• Press l l to decrease the value.

7 Press kMENU to exit from set menu.

■ Front speakers, Center speaker, Surround left/right speakers FRONT, CENTER, SUR. LR

Select “LARGE (LRG)” or “SMALL (SML)” depending on the size of your each speaker. When Center speaker or Surround speakers is not connected, select “NONE.” Initial setting:

FRONT: “LARGE” CENTER: “SML” SUR. LR: “SML”

Notes

• When “BASS OUT” is set to “FRNT” (see page 32), you can select only

“LARGE” in “FRONT.” If “FRONT” is set to a setting other than “LARGE” in advance, this unit automatically changes the value to “LARGE.”

• When you select “NONE” in “CENTER,” the center channel signals are

directed to the front left and right speakers.

• When you select “NONE” in “SUR. LR,” this unit is automatically enters

the Virtual CINEMA DSP mode (see page 26).

■ LFE/Bass out BASS OUT

Use this feature to select the speakers that output the LFE (low-frequency effect) and the low-frequency signals.

• If you are not satisfied with the bass sounds from your speakers, you can

change these settings according to your preference.

32 En

Page 37

Set menu

LFE signals output

Choice Subwoofer Front speakers Other speakers

BOTH* Output No output No output

SWFR Output No output No output

FRONT No output Output No output

Low-frequency signals output

Choice Subwoofer Front speakers Other speakers

BOTH**1 *2 *3

SWFR *4 *3 *3

FRONT No output *1 *3

Notes

*1 Outputs the low-frequency signals of the front channels and other

speakers to “SML” or “NONE.” *2 Always output the low-frequency signals of the front channels. *3 Output the low-frequency signals if the sizes of speakers are set to

“LARGE” (or “LRG”). *4 Output the low-frequency signals of the speakers set to “SML.”

■ Crossover CROSSOVER

Use this feature to select a crossover frequency of all the speakers set to “SML” (or “SMALL”) or to “NONE” in “SPEAKER SET” (see pages 31 and 32). Choices: 40Hz, 60Hz, 80Hz*, 90Hz, 100Hz, 110Hz,

120Hz, 160Hz, 200Hz

Note

• All frequencies below the selected frequency will be sent to the

subwoofer or to the speakers set to “LRG” (or “LARGE”) in “SPEAKER SET” (see pages 31 and 32).

■ Subwoofer phase SWFR PHASE

Use this feature to switch the phase of your subwoofer if bass sounds are lacking or unclear.

Choice Function

NRM* Does not reverse the phase of your subwoofer.

REV Sets the phase of your subwoofer to reverse.

Speaker level B)SP LEVEL

Use this feature to manually adjust the output level of each speaker. Control range: –10 to 0* to +10 dB Control step: 1 dB

SP LEVEL Adjusted speaker

FL Front left speaker

FR Front right speaker

C Center speaker

SL Surround left speaker

SR Surround right speaker

SWFR Subwoofer

Notes

• The available speaker channels differ depending on the setting of the

speakers.

• This does not affect recorded material.

Speaker distance C)SP DISTANCE

Use this feature to manually adjust the distance of each speaker and the delay applied to the respective channel. All sounds would be adjusted to arrive at the listening position at the same time regardless of distance from each speaker.

■ Unit UNIT

Choice Condition

meters When you adjust speaker distances in meters.

feet* When you adjust speaker distances in feet.

■ Speaker distances

Control range: 0.30 to 24.00 m (1.0 to 80.0 ft) Control step: 0.10 m (0.5 ft) Initial setting:

FRONT L/FRONT R/SWFR: 3.00 m (10.0 ft) CENTER: 2.60 m (8.5 ft) SUR. L/SUR. R: 2.40 m (8.0 ft)

SP DISTANCE Adjusted speaker

FRONT L Front left speaker

FRONT R Front right speaker

CENTER Center speaker

SUR. L Surround left speaker

SUR. R Surround right speaker

SWFR Subwoofer

Note

• The available speaker channels differ depending on the setting of the

speakers.

Center graphic equalizer D)CENTER GEQ

Use this feature to adjust the built-in 5-frequency band (100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphic equalizer for the center channel so that the tonal quality of the center speaker matches that of the front speakers. Control range: –6.0 to 0* to +6.0 dB Control step: 0.5 dB

• Press lk / n to select a frequency band and ll / h to adjust the

selected frequency band.

• You can make adjustment while listening to the currently source or a test

tone.

Following is an example where “100Hz” is selected as the frequency band.

100Hz--||-- 0

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

English

33 En

Page 38

Set menu

■ Test to n e TEST

Use this feature to make adjustments for “CENTER GEQ” while listening to a test tone.

Choice Function

OFF* Stops test tones and output the currently.

ON Outputs test tones from the center and from left

speakers.

Low-frequency effect level E)LFE LEVEL

Use this feature to adjust the output level of the LFE (lowfrequency effect) channel according to the capacity of your subwoofer or headphones. Control range: –20 to 0* dB Control step: 1 dB

■ Speaker LFE SP LFE

Adjusts the speaker LFE level.

■ Headphone LFE HP LFE

Adjusts the headphone LFE level.

Notes

• Depending on the settings of “BASS OUT” (see page 32), some signals

may not be output at the SUBWOOFER OUTPUT jack.

• The LFE channel carries low-frequency special effects which are only

added to certain scenes.

• This setting is effective when the input signal contains the LFE channel.

Dynamic range F)D.RANGE

Use this feature to select the amount of dynamic range compression to be applied to your speakers or headphones. This setting is effective only when this unit is decoding Dolby Digital and DTS signals.

Choice Function

MIN Adjusts the dynamic range to narrow.

STD Adjusts the dynamic range to medium.

MAX* Preserves the greatest amount of dynamic range.

■ Speaker dynamic range SP D.R

Adjusts the speaker compression.

■ Headphone dynamic range HP D.R

Adjusts the headphone compression.

Audio settings G)AUDIO SET

Use this feature to adjust the overall audio settings of this unit.

■ Mute type MUTE TYP.

Use this feature to adjust how much the mute function reduces the output volume (see page 19).

Choice Function

FULL* Completely mutes all the audio output.

-20dB Reduces the current volume by 20 dB.

■ Audio delay A.DELAY

Use this feature to delay the sound output and synchronize it with the video image. This may be necessary for certain LCD monitors or projectors. Control range: 0* to 160 ms Control step: 1 ms

■ Maximum volume MAX VOL.

Use this feature to set the maximum volume level regardless of the original volume range. This feature is useful to avoid the unexpected loud sound. Control range: +16 dB*, +10 dB to –30 dB Control step: 5 dB

Note

• The “MAX VOL.” setting takes priority over the “Initial Volume”

setting. For example, if “INI.VOL.” is set to –20 dB and “MAX VOL.” is set to –30 dB, the volume level is automatically set to –30 dB when you turn on the power of this unit next time.

■ Initial volume INI.VOL.

Use this feature to set the volume level when the power of this unit is turned on. Choices: Off*, –80 dB to +16 dB Control step: 1 dB

Note

• The “MAX VOL.” setting takes priority over the “INI.VOL.” setting.

2 INPUT MENU

Use this menu to reassign the input jacks, select the input mode or rename the input source.

• Initial settings are indicated by (*) in this following each parameter.

Input assignment A)INPUT ASSIGN

Use this feature to assign the input jacks according to the component to be used if the initial settings of this unit do not correspond to your needs.

Choices: CD, MD/CD-R, DVD, DTV/CBL, V-AUX, DVR Initial setting:

IN (1) (COAXIAL jack): DVD IN (2) (OPTICAL (DTV/CBL) jack): DTV/CBL IN (3) (OPTICAL (CD) jack): CD

Notes

• You cannot select a specific item more than once.

• You cannot assign the same input source to both “IN (2)” and “IN (3).”

For example, you assign “CD” to “IN (2),” “–– –” appears in “IN (3).”

• Once the input jacks are reassigned, you can select the corresponding

component by using NINPUT l / h (or the input selector buttons (f) on the remote control).

Input rename B)INPUT RENAME

Use this feature to change the name of the input source that appears on the front panel display.

34 En

Page 39

Set menu

The following is an example where “DVD” is renamed “My DVD.”

DVR

V-AUX DTV/CBL

DVD CD

MD/CD-R

TUNER

DVD My DVD

1 Press one of the input selector buttons (f)

or vMULTI CH IN to select the input source you want to change the name of.

2 Press hAMP and then press l l / h on the

remote control to place the “_” (underscore) under the space or the character you want to edit.

3 Press lk / n to select the character you

want to use and then press ll / h to move to the next space.

Notes

• You can use up to 8 characters for each input.

• Press l n to change the character in the following order, or press

lk to go in the reverse order: A to Z, a space, 0 to 9, a space, a to z, a space, symbols (#, *, –, +, etc.)

4 Repeat steps 1 through 3 to rename each

input source.

5 Press kMENU to exit from “INPUT

RENAME.”

Volume trim C)VOLUME TRIM

Use this feature to adjust the level of the signal input at each jack. This is useful if you want to balance the level of each input source to avoid sudden changes in volume when switching between input sources.

Press one of the input selector buttons (f) or vMULTI CH IN to select the input source you

want to adjust the level.

Choices: CD, TUNER, MD/CD-R, DVD, DTV/CBL,

V-AUX (DOCK), DVR, MULTI CH IN Control range: –6.0 to 0.0* to +6.0 dB Control step: 1.0 dB

■ DTS decoder prioritize setting

Choice Function

AUTO* Automatically detect the type of input signals and

selects the appropriate input mode.

DTS Enables to playback a DTS-CD.

Multi channel input setup

E)MULTI CH SET

■ BGV BGV

Use this feature to select the video source played in the background of the sources input from the MULTI CH INPUT jacks. Choices: LAST*, DVR, V-AUX, DTV/CBL, DVD

• Select “LAST” to set this unit to automatically select the last selected

video source as the background video source.

3 OPTION MENU

Use this menu to adjust the optional system parameters.

• Initial settings are indicated by (*) in this following each parameter.

Display settings A)DISPLAY SET

■ Dimmer DIMMER

Use this feature to adjust the brightness of the front panel display. Control range: –4 to 0* Control step: 1

• Press ll to make the front panel display dimmer.

• Press lh to make the front panel display brighter.

Memory guard B)MEMORY GUARD

■ Memory guard MEM.GUARD

Use this feature to prevent accidental changes to DSP program parameter values and other system settings.

Choice Function

OFF* Turns off the “MEM.GUARD” feature.

ON Protects:

– sound field program parameters – all set menu items – SCENE template parameters

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

Decoder mode D)DECODER MODE

■ Decoder select mode

Use this feature to designate the default decoder mode for the input sources connected to the DIGITAL INPUT jacks.

Choice Function

AUTO* Automatically detect the type of input signals and

selects the appropriate decoder mode.

LAST Automatically select the last decoder mode used the

connected input source.

Note

• When “MEM.GUARD” is set to “ON,” you cannot select and adjust any

other set menu items.

English

35 En

Page 40

Set menu

Audio select C)AUDIO SELECT

Use this feature to designate the default audio input jack select setting for the input sources.

Choice Function

AUTO* Automatically detect the type of input signals and

select the appropriate input mode.

LAST Automatically select the last input mode used for the

connected input source (see page 18).

Parameter initialization D)PARAM. INI

Use this feature to set all the parameters of the sound field programs to the initial factory settings.

Choice Function

NO* Cancels the parameter initialization and returns to the

previous menu level.

YES Sets all the sound field parameters to the initial factory

settings.

Notes

• You cannot automatically revert to the previous parameter settings once

you initialize the sound field program parameters.

• You cannot separately initialize individual sound field programs.

Bluetooth setting E)BLUETOOTH

4 Press nRETURN to exit from “START

PAIRING.”

Notes

• If the connected Bluetooth receiver cannot find any Bluetooth

components, “Not found” appears.

• If a Bluetooth receiver is not connected to this unit, “No BT adapter”

appears.

■ Start pairing START PAIRING

Use this feature to start pairing the connected Bluetooth Wireless Audio Receiver (such as YBA-10, sold separately) with your Bluetooth component. For details about the pairing, refer to “Pairing the Bluetooth™ receiver and your Bluetooth™ component” on page 30.

To ensure security, a time limit of 8 minutes is set for the pairing operation. You are recommended to read and fully understand all the instructions before starting.

1 Select “START PAIRING” in “BLUETOOTH”

and then press lENTER to start pairing.

The connected Bluetooth receiver starts searching Bluetooth components. “Searching...” appears on the front panel display.

2 Check that the Bluetooth component detects

the Bluetooth receiver.

For details, refer to the instruction manual of the Bluetooth component.

3 Select the Bluetooth receiver in the

Bluetooth device list and then enter the pass key “0000” on the Bluetooth component.

Once this unit completes the pairing successfully, “Completed” appears.

• To cancel the pairing, press n RETURN to exit from “START

PAIRING.”

36 En

Page 41

Remote control features

In addition to controlling this unit, the remote control can also operate other audiovisual components made by Yamaha and other manufacturers. To control your TV or other components, you must set up the appropriate remote control code for each input source (see page 39).

Controlling this unit, a TV, or other components

INTRODUCTION

■ Controlling this unit

Press hAMP to control this unit.

POWER

STANDBY

POWER

AVTV

A B C

DTV/CBL DVR

D E

TV INPUT

SCENE

ENTER

ENHANCER

MUTE

TV CH

TV VOL

TV MUTE

4321

VOLUME

DISPLAY

SUR. DECODE

4321

NIGHT

SLEEP

ENT

10709

AMP

CD MD/CD-R TUNER

DVD

V-AUX/DOCK

AMP

BAND LEVEL

TITLE

RETURN

REC

l PROG h

STRAIGHT

MULTI CH IN AUDIO SEL

Notes

*1 These buttons always control this unit. *2 These buttons control this unit only when hAMP is pressed.

■ Controlling a TV

Press fDTV/CBL to control your TV. To control your TV, set the appropriate remote control code for fDTV/ CBL (see page 39).

POWER

STANDBY

POWER

AVTV

A B C

MUTE

CD MD/CD-R TUNER

TV CH

DTV/CBL DVR

DTV/CBL

DVD

V-AUX/DOCK

AMP

BAND LEVEL

TITLE

RETURN

REC

l PROG h

STRAIGHT

MULTI CH IN AUDIO SEL

TV INPUT

D E

ENTER

TV MUTE

SCENE

DISPLAY

ENHANCER

NIGHT

10709

TV VOL

VOLUME

SUR. DECODE

SLEEP

ENT

4321

Notes

*1 These buttons always control your TV regardless of whether you press

fDTV/CBL or not.

Remote control Digital TV/Cable TV

TV POWER Turns on or off the power.

TV CH +/– Changes the channel number.

TV VOL +/– Increases or decreases the volume

level.

TV INPUT Changes the input source.

TV MUTE Mutes the audio output.

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

*2 These buttons control your TV only when fDTV/ CBL is pressed.

For details, see the “Digital TV/Cable TV” column on page 38.

• You can control more than one TV by setting the appropriate remote

control code for any input source selector buttons other than fDTV/ CBL. In such a case, you can control the buttons highlighted above (*1 and *2) when you press the input source selector button.

37 En

English

Page 42

Remote control features

■ Controlling other components

Press one of the input selector buttons (f) or A to E buttons to control other components. You must set the appropriate remote control code for each input source in advance (see page 39). The following table shows the function of each control button used to control other components assigned to each input selector button. Be advised that some buttons may not correctly operate the selected component.

• The remote control has 13 modes (input areas) to control components so

that the remote control can operate up to 13 different components.

• When you press one of the optional component control area buttons (A to

E), you can control the desired component without changing the input source of this unit.

[1]

POWER

AVTV

A B C

CD MD/CD-R TUNER

DVD

DTV/CBL DVR

D E

V-AUX/DOCK

AMP

TV INPUT

SCENE

STANDBY

TV MUTE

POWER

BAND LEVEL

TITLE

[2]

MUTE

TV VOL

[3]

TV CH

REC

RETURN

[4]

[5]

l PROG h

[6]

STRAIGHT

MULTI CH IN AUDIO SEL

4321

VOLUME

ENTER

DISPLAY

ENHANCER

NIGHT

10709

SUR. DECODE

4321

SLEEP

ENT

[7]

[8]

[9]

Remote control

DVD p layer /

recorder

VCR

Digital TV/

Cable TV

LD player CD player

MD/CD

recorder

Tuner

[1] AV POWER Power *1 Power *1 Power *2 Power *1 Power *1 Power *1

[2] TITLE Title Band

[3] PRESET/CH k Up VCR channel upUp Preset up

(1-8)

PRESET/CH n Down VCR channel

down

Down Preset down

(1-8)

A/B/C/D/E l Left Left Preset down

(A-E)

A/B/C/D/E h Right Right Preset up

(A-E)

ENTER Enter Enter

[4] RETURN Return Return

[5] REC Disc skip

Rec Rec *2 Disc skip Rec

(player)

Rec (recorder)

p Play Play Play *2 Play Play Play

w Search

backward

f Search

forward

backward

forward

backward *2

forward *2

backward

forward

backward

forward

backward

forward

e Pause Pause Pause *2 Pause Pause Pause

b Skip

backward

Skip

backward

Skip

backward *2

Skip

backward

Skip

backward

Skip

backward

a Skip forward Skip forward Skip forward *2Skip forward Skip forward Skip forward

s Stop Stop Stop *2 Stop Stop Stop

[6] 1-9, 0, +10 Numeric

butto ns

Numeric

buttons

Numeric

buttons

Numeric

buttons

Numeric

buttons

Numeric

buttons

[7] MENU Menu Menu

[8] DISPLAY Display Display Display Display Display Display

[9] ENT Title/Index Enter Enter Chapter/Time Index Index

Notes

*1 This button is operational only when the original remote control supplied with the component has a POWER button. *2 These buttons operate your DVD recorder only when you set the appropriate remote control code for DVR (see page 39).

38 En

Preset stations

(1-8)

Page 43

Remote control features

Setting remote control codes

You can control other components by setting the appropriate remote control codes. For a complete list of available remote control codes, refer to “List of remote control codes” at the end of this manual.

Remote control code default settings

Input

source

CD CD Yamaha 5013

MD/CD-R CD-R Yamaha 5001

TUNER TUNER Yamaha 5007

DVD DVD Yamaha 2000

DTV/CBL — — —

V-AUX/

DOCK

DVR DVR Yamaha 2011

A TUNER Yamaha 5012

B TUNER Yamaha 5009

C TUNER Yamaha 5017

D— ——

E— ——

Note

• You may not be able to operate your Yamaha component even if a

Yamaha remote control code is preset as listed above. In this case, try setting another Yamaha remote control code.

1 While pressing and holding one of the input

selector buttons (f) on the remote control to select the input area you want to set up, press bAV POWER for more than 3 seconds.

Component

Advanced setup

This unit has additional menus that are displayed on the front panel display. The advanced setup menu offers additional operations to adjust and customize the way this unit operates. Change the initial settings (indicated by (*) in this following parameter) to reflect the needs of your listening environment.

Notes

• Only ASTANDBY/ON, LPROGRAM l / h and

STRAIGHT are effective while you are using the advanced setup

menu.

• No other operations can be made while you are using the advanced setup

menu.

• The advanced setup menu is only available on the front panel display.

1 Press

STANDBY/ON on the front panel to

set this unit to the standby mode.

2 Press and hold

TONE CONTROL and then press ASTANDBY/ON to turn on this unit.

This unit turns on, and the advanced setup menu appears on the front panel display.

3 Press

PROGRAM l / h to select the

parameter you want to adjust.

The name of the selected parameter appears on the front panel display.

4 Press

STRAIGHT repeatedly to change

the selected parameter setting.

5 Press

STANDBY/ON to confirm your selection and set this unit to the standby mode.

• The settings you made are reflected next time you turn on this unit.

■ Speaker impedance SP IMP.

(U.S.A. and Canada models only)

Caution

If you are to use 6 ohm speakers, set “SP IMP.” to “6ΩMIN” as follows BEFORE using this unit.

Use this feature to set the speaker impedance of this unit so that it matches that of your speakers. Choices: 8ΩMIN*, 6ΩMIN

• Select “8ΩMIN” to set the speaker impedance to 8 Ω .

• Select “6ΩMIN” to set the speaker impedance to 6 Ω .

SP IMP. Speaker Impedance level

Front (A or B) The impedance of each

8ΩMIN

6ΩMIN

Center

Surround

Front (A or B) The impedance of each

Center

Surround

speaker must be 8 Ω or

higher.

speaker must be 6 Ω or

higher.

■ Initializing PRESET

Use this feature to reset all the parameters of this unit to the initial factory settings. Choices: CANCEL*, RESET

• Select “CANCEL” not to reset any parameters of this

unit.

• Select “RESET” to reset the parameters of this unit.

Notes

• This setting completely resets all the parameters of this unit including the

set menu parameters. However, the advanced setup menu parameters will not be initialized.

• The initial factory settings are activated next time you turn on this unit.

40 En

Page 45

ADDITIONAL INFORMATION

Troubleshooting

Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center.

■ General

Problem Cause Remedy

This unit fails to turn on or enters the standby mode soon after the power is turned on.

No sound Incorrect input or output cable

The sound suddenly goes off.

The power cable is not connected or the

plug is not completely inserted.

The speaker impedance setting is

incorrect.

The protection circuitry has been

activated.

This unit has been exposed to a strong

external electric shock (such as lightning

or strong static electricity).

connections.

No appropriate Audio input jack select has

been set.

No appropriate input source has been

selected.

Speaker connections are not secure. Secure the connections. 9

The front speakers to be used have not

been selected properly.

The volume is turned down. Turn up the volume. —

The sound is muted. Press e MUTE or m VOLUME +/– on the remote

Signals this unit cannot reproduce are

being input from a source component,

such as a CD-ROM.

Audio signals input at the HDMI jack are

not output from any speaker terminals.

The setting of the connected component is

improper.

The protection circuitry has been activated

because of a short circuit, etc.

The sleep timer has turned off this unit. Turn on this unit, and play the source again. —

The sound is muted. Press e MUTE or m VOLUME +/– on the remote

Connect the power cable firmly. —

Set the speaker impedance to match your speakers. 40

Make sure that all speaker wire connections on this

unit and on all speakers are secure and that the wire

for each connection does not touch anything other

than its respective connection.

Set this unit to the standby mode, disconnect the

power cable, plug it back in after 30 seconds and then

use it normally.

Connect the cables properly. If the problem persists,

the cables may be defective.

Set an appropriate Audio input jack select. 36

Select an appropriate input source with

INPUT l / h on the front panel (or the input

selector buttons (f) on the remote control).

Select the front speakers with CSPEAKERS.18

control to resume audio output and then adjust the

volume.

Play a source whose signals can be reproduced by this

unit.

Make an analog or digital connection beside the

HDMI connection.

Make an appropriate setting following the instruction

manual of the connected component.

Check that the impedance setting is correct. 40

Check that the speaker wires are not touching each

other and then turn this unit back on.

control to resume audio output.

See

page

—

11-13

17, 18

—

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

English

41 En

Page 46

Troubleshooting

Problem Cause Remedy

Sound is heard from the speaker on one side only.

Only the center speaker outputs substantial sound.

No sound is heard from the center speaker.

No sound is heard from the surround speakers.

No sound is heard from the subwoofer.

Dolby Digital or DTS sources cannot be played. (Dolby Digital or DTS indicator on the front panel display does not light up.)

A humming sound is heard.

The volume level cannot be increased, or the sound is distorted.

The sound effect cannot be recorded.

A source cannot be recorded by an analog component connected to the AUDIO OUT (REC) jack.

Incorrect cable connections. Connect the cables properly. If the problem persists,

the cables may be defective.

Incorrect settings in “SP LEVEL.” Adjust the “SP LEVEL” settings. 33

When playing a monaural source with a

CINEMA DSP program, the source signal

is directed to the center channel, and the

front and surround speakers output effect

sounds.

“CENTER” in “SPEAKER SET” is set to

“NONE.”

Some sound field programs do not output

sounds from the center speaker.

“SUR. LR” in “SPEAKER SET” is set to

“NONE.”

This unit is in the “STRAIGHT” mode

and a monaural source is being played

back.

“BASS OUT” in “SPEAKER SET” is set

to “FRNT” when a Dolby Digital or DTS

signal is being played.

“BASS OUT” in “SPEAKER SET” is set

to “SWFR” or “FRNT” when a 2-channel

source is being played.

The source does not contain low-

frequency bass signals.

The connected component is not set to

output Dolby Digital or DTS digital

signals.

Audio input jack select is set to

“AN AL OG .”

Incorrect cable connections. Connect the audio cables firmly. If the problem

You are attempting to set the volume level

higher than the maximum volume level.

The component connected to the AUDIO

OUT (REC) jack on this unit is turned off.

It is not possible to record the sound effect

with a recording component.

The source component is not connected to

the analog AUDIO IN jacks on this unit.

Set “CENTER” to “SML” or “LRG.” 32

Try another sound field program. 25

Set “SUR. LR” to “SML” or “LRG.” 32

Press MSTRAIGHT on the front panel so that

“STRAIGHT” disappears from the front panel

display.

Set “BASS OUT” to “SWFR” or “BOTH.” 32

Set “BASS OUT” to “BOTH.” 32

Make an appropriate setting following the operating

instructions for your component.

Set Audio input jack select to “AUTO.” 18

persists, the cables may be defective.

Adjust “MAX VOL.” setting. 34

Turn on the power of the component. —

Connect the source component to the analog AUDIO

IN jacks.

See

page

11-14

—

42 En

Page 47

Troubleshooting

Problem Cause Remedy

The sound field parameters and some other settings of this unit cannot be changed.

This unit does not operate properly.

“CHECK SP WIRES” appears on the front panel display.

There is noise interference from digital or radio frequency equipment.

The picture is disturbed.

This unit suddenly enters the standby mode.

Virtual CINEMA DSP is not activated.

SILENT CINEMA is not activated.

“MEM.GUARD” in “OPTION MENU” is

set to “ON.”

The internal microcomputer has been

frozen by an external electric shock (such

as lightning or excessive static electricity)

or by a power supply with low voltage.

Speaker cables are short-circuited. Make sure all speaker cables are connected correctly. 9

This unit is too close to the digital or high-

frequency equipment.

The video source uses scrambled or

encoded signals to prevent dubbing.

The internal temperature is too high and

the overheat protection circuitry has been

activated.

“MULTI CH” is selected as the input

source.

Headphones are connected to the

PHONES jack.

This unit is in the “5ch Stereo” mode. Exit from the “5ch Stereo” mode. 21

“MULTI CH” is selected as the input

source.

The unit is in the “2ch Stereo,”

“STRAIGHT” or “Music Enh.2ch” mode.

Set “MEM.GUARD” to “OFF.” 35

Disconnect the power cable from the AC wall outlet

and then plug it in again after about 30 seconds.

Move this unit further away from such equipment. —

Wait about 1 hour for this unit to cool down and then

turn it back on.

Select an input source other than “MULTI CH.” 17

Disconnect the headphone plug from the PHONES

jack.

Select an input source other than “MULTI CH.” 17

Exit from the “2ch Stereo,” “STRAIGHT” or “Music

Enh2ch” mode.

■ Tu ne r

See

page

—

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

Problem Cause Remedy

FM stereo reception is noisy.

There is distortion, and clear reception cannot be obtained even with a

good FM antenna.

The desired station cannot be tuned into with the automatic tuning method.

Previously preset stations can no longer be tuned into.

See

page

The characteristics of FM stereo

broadcasts may cause this problem

when the transmitter is too far away or

the antenna input is poor.

There is multi-path interference. Adjust the antenna position to eliminate

The signal is too weak. Use a high-quality directional FM antenna. —

This unit has been disconnected for a

long period.

Check the antenna connections. 15

Try using a high-quality directional FM

antenna.

Use the manual tuning method. 27

multi-path interference.

Use the manual tuning method. 27

Set preset stations. 27

43 En

—

English

Page 48

Troubleshooting

Problem Cause Remedy

The desired station cannot be tuned into with the automatic tuning method.

There are continuous crackling and hissing noises.

There are buzzing and whining noises.

The signal is weak or the antenna

connections are loose.

Noises result from lightning,

fluorescent lamps, motors, thermostats

and other electrical equipment.

A TV set is being used nearby. Move this unit away from the TV set. —

Tighten the AM loop antenna connections and

orient it for the best reception.

Use the manual tuning method. 27

Use an outdoor antenna and a ground wire.

This will help somewhat, but it is difficult to

eliminate all noise.

■ iPod

Note

• In case of a transmission error without a status message appearing on the front panel display, check the connection to your iPod (see page 14).

Status message Cause Remedy

Connect error There is a problem with the signal path

from your iPod to this unit.

Unknown iPod The iPod being used is not supported by

this unit.

iPod connected Your iPod is properly stationed in a

Yamaha iPod universal dock (such as

YDS-11, sold separately) connected to the

DOCK terminal of this unit, and the

connection between your iPod and this

unit is complete.

Disconnected Your iPod was removed from a Yamaha

iPod universal dock (such as YDS-11,

sold separately) connected to the DOCK

terminal of this unit.

Turn off this unit and reconnect the Yamaha iPod

universal dock to the DOCK terminal of this unit.

Try resetting your iPod. —

Only iPod (Click and Wheel), iPod nano, and iPod

mini are supported.

Station your iPod back in a Yamaha iPod universal

dock (such as YDS-11, sold separately) connected to

the DOCK terminal of this unit.

See

page

—

See

page

—

■ Bluetooth

Status message Cause Remedy

Searching... The Bluetooth receiver and the Bluetooth

component is in the middle of the pairing.

The Bluetooth receiver and the Bluetooth

component is in the middle of establishing

the connection.

Completed The paring is completed.

Canceled The paring is canceled.

BT connected The connection between the Bluetooth

Wireless Audio Receiver (such as YBA-

10, sold separately) and the Bluetooth

component is established.

Disconnected The Bluetooth component is disconnected

from the Bluetooth receiver (such as

YBA-10, sold separately).

No BT adapter The Bluetooth receiver is not connected to

the DOCK terminal.

Connect the Bluetooth Wireless Audio Receiver (such

as YBA-10, sold separately) to the DOCK terminal.

44 En

See

page

Page 49

■ Remote control

Troubleshooting

Problem Cause Remedy

The remote control does not work nor function properly.

Wrong distance or angle. The remote control functions within a maximum

range of 6 m (20 ft) and no more than 30 degrees off-

axis from the front panel.

Direct sunlight or lighting (from an

inverter type of fluorescent lamp, etc.) is

striking the remote control sensor of this

unit.

The batteries are weak. Replace all batteries. 8

The remote control code is not correctly

set.

Even if the remote control code is

correctly set, there are some models that

do not respond to the remote control.

Reposition this unit. —

Set the remote control code correctly using “List of

remote control codes” at the end of this manual.

Try setting another code for the same manufacturer

using “List of remote control codes” at the end of this

manual.

See

page

■ Resetting the system

Use this feature to reset all the parameters of this unit to the initial factory settings. For details about the procedure of resetting the system, see “Initializing” in “Advanced setup” on page 40.

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

45 En

INFORMATION APPENDIX

ADDITIONAL

English

Page 50

Glossary

■ Audio information

Dolby Digital

Dolby Digital is a digital surround sound system that gives you completely independent multi-channel audio. With 3 front channels (front L/R and center), and 2 surround stereo channels, Dolby Digital provides 5 full-range audio channels. With an additional channel especially for bass effects, called LFE (Low Frequency Effect), the system has a total of 5.1-channels (LFE is counted as 0.1 channel). By using 2-channel stereo for the surround speakers, more accurate moving sound effects and surround sound environment are possible than with Dolby Surround. The wide dynamic range from maximum to minimum volume reproduced by the 5 full-range channels and the precise sound orientation generated using digital sound processing provide listeners with unprecedented excitement and realism. With this unit, any sound environment from monaural up to a 5.1-channel configuration can be freely selected for your enjoyment.

Dolby Pro Logic II

Dolby Pro Logic II is an improved technique used to decode vast numbers of existing Dolby Surround sources. This new technology enables a discrete 5-channel playback with 2 front left and right channels, 1 center channel, and 2 surround left and right channels instead of only 1 surround channel for conventional Pro Logic technology. There are three modes available: “Music mode” for music sources, “Movie mode” for movie sources and “Game mode” for game sources.

Dolby Surround

Dolby Surround uses a 4-channel analog recording system to reproduce realistic and dynamic sound effects: 2 front left and right channels (stereo), a center channel for dialog (monaural), and a surround channel for special sound effects (monaural). The surround channel reproduces sound within a narrow frequency range. Dolby Surround is widely used with nearly all video tapes and laser discs, and in many TV and cable broadcasts as well. The Dolby Pro Logic decoder built into this unit employs a digital signal processing system that automatically stabilizes the volume on each channel to enhance moving sound effects and directionality.

DTS Digital Surround

DTS digital surround was developed to replace the analog soundtracks of movies with a 5.1-channel digital sound track, and is now rapidly gaining popularity in movie theaters around the world. DTS, Inc. has developed a home theater system so that you can enjoy the depth of sound and natural spatial representation of DTS digital surround in your home. This system produces practically distortion-free 5.1channel sound (technically, left, right and center channels, 2 surround channels, plus an LFE 0.1 channel as a subwoofer, for a total of 5.1channels).

LFE 0.1 channel

This channel reproduces low-frequency bass signals. The frequency range of this channel is from 20 Hz to 120 Hz. This channel is counted as 0.1 because it only enforces a low-frequency range compared to the full-range reproduced by the other 5 channels in Dolby Digital or DTS

5.1-channel systems.

PCM (Linear PCM)

Linear PCM is a signal format under which an analog audio signal is digitized, recorded and transmitted without using any compression. This is used as a method of recording CDs and DVD audio. The PCM system uses a technique for sampling the size of the analog signal per very small unit of time. Standing for “Pulse Code Modulation,” the analog signal is encoded as pulses and then modulated for recording.

Sampling frequency and number of quantized bits

When digitizing an analog audio signal, the number of times the signal is sampled per second is called the sampling frequency, while the degree of fineness when converting the sound level into a numeric value is called the number of quantized bits. The range of rates that can be played back is determined based on the sampling rate, while the dynamic range representing the sound level difference is determined by the number of quantized bits. In principle, the higher the sampling frequency, the wider the range of frequencies that can be played back, and the higher the number of quantized bits, the more finely the sound level can be reproduced.

■ Sound field program information

CINEMA DSP

Since the Dolby Surround and DTS systems were originally designed for use in movie theaters, their effect is best felt in a theater having many speakers designed for acoustic effects. Since home conditions, such as room size, wall material, number of speakers, and so on, can differ so widely, it is inevitable that there are differences in the sound heard. Based on a wealth of actually measured data, Yamaha CINEMA DSP uses Yamaha original DSP technology to combine Dolby Pro Logic, Dolby Digital and DTS systems to provide the audiovisual experience of movie theater in the listening room of your own ho me.

SILENT CINEMA

Yamaha has developed a natural, realistic sound effect DSP algorithm for headphones. Parameters for headphones have been set for each sound field program so that accurate representations of all the sound field programs can be enjoyed on headphones.

Virtual CINEMA DSP

Yamaha has developed a Virtual CINEMA DSP algorithm that allows you to enjoy DSP surround effects even without any surround speakers by using virtual surround speakers. It is even possible to enjoy Virtual CINEMA DSP using a minimal two-speaker system that does not include a center speaker.

■ Video information

Component video signal

With the component video signal system, the video signal is separated into the Y signal for the luminance and the PB and PR signals for the chrominance. Color can be reproduced more faithfully with this system because each of these signals is independent. The component signal is also called the “color difference signal” because the luminance signal is subtracted from the color signal. A monitor with component input jacks is required in order to output component signals.

Composite video signal

With the composite video signal system, the video signal is composed of three basic elements of a video picture: color, brightness and synchronization data. A composite video jack on a video component transmits these three elements combined.

46 En

Page 51

Specifications

AUDIO SECTION

• Minimum RMS Output Power for Front, Center, Surround [U.S.A. and Canada models]

1 kHz, 0.9% THD, 8 Ω ............................................... 100 W/ch

[Other models]

1 kHz, 0.9% THD, 6 Ω ............................................... 100 W/ch

• Maximum Power (JEITA) [U.S.A. and Canada models]

1 kHz, 10% THD, 8 Ω ................................................ 135 W/ch

[Asia, China, Korea and General models]

1 kHz, 10% THD, 6 Ω ................................................. 135 W/ch

• MAX Power Per Channel [U.K., Russia, and Europe models]

1 kHz, 0.7% THD, 4 Ω ...................................... 105 W or more

• IEC Power [U.K., Russia, and Europe models]

1 kHz, 0.1% THD, 6 Ω ........................................ 90 W or more

• Dynamic Power [U.S.A. and Canada models] (Impedance Selector: 8 Ω)

(IHF, 8/6/4/2 Ω) .......................................... 110/130/160/180 W

[Other models]

(IHF, 6/4/2 Ω) .................................................... 105/130/150 W

• Dynamic Headroom [U.S.A. and Canada models]

8 Ω .................................................................................... 0.41 dB

• Frequency Response

CD, etc. to Front ................................ 10 Hz to 100 kHz, 0/–3 dB

V-AUX to Front ................................... 10 Hz to 20 kHz, 0/–3 dB

• Total Harmonic Distortion CD, etc. (2ch stereo) to Front SP OUT,

[U.S.A. and Canada models]

1 kHz, 50 W/8 Ω ................................................... 0.06% or less

[Other models]

1 kHz, 50 W/6 Ω ................................................... 0.06% or less

• Signal to Noise Ratio (IHF-A Network) CD, etc. (STEREO) Input shorted

250 mV ............................................................... 100 dB or more

200 mV ................................................................. 98 dB or more

• Residual Noise (IHF-A Network)

Front L/R ............................................................... 170 µV or less

• Channel Separation CD, etc. Input 5.1 kΩ shorted (1 kHz/10 kHz)

................................................................... 60 dB/45 dB or more

• Tone Control

BASS Boost/Cut ................................................... ±10 dB/100 Hz

TREBLE Boost/Cut .............................................. ±10 dB/20 kHz

• Headphone Jack Rated Output/Impedance

CD, etc. (1 kHz, 200 mV, 8 Ω)....................................0.4 V/470 Ω

• Input Sensitivity/Input Impedance

CD, etc. ................................................................. 200 mV/47 kΩ

MULTI CH INPUT ............................................... 200 mV/47 kΩ

• Maximum Input Signal

CD, etc. 1 kHz, 0.5%THD (EFFECT ON) ............. 2.0 V or more

• Output Level/Output Impedance

AUDIO OUT (REC) ............................................ 200 mV/1.2 kΩ

SUBWOOFER OUTPUT

(2ch Stereo and FRONT SP: SMALL) ..................... 4 V/1.2 kΩ

• Filter Characteristics (fc=40/60/80/90/100/110/120/160/200 Hz)

H.P.F. (Front, Center, Surround) ................................... 12 dB/oct.

L.P.F. (Subwoofer) ........................................................ 24 dB/oct.

VIDEO SECTION

• Signal Level

Composite ................................................................. 1 Vp-p/75 Ω

Component .................. 1 Vp-p/75 Ω (Y), 0.7 Vp-p/75 Ω (PB/PR)

• Video Maximum Input Level ................................ 1.5 Vp-p or more

• Signal to Noise Ratio ................................................ 50 dB or more

• Frequency Response (MONITOR OUT)

Component Signal .................................... 5 Hz to 60 MHz, –3 dB

FM SECTION

• Tuning Range

[U.S.A. and Canada models] ........................... 87.5 to 107.9 MHz

[Asia and General models] .........87.5/87.50 to 108.0/108.00 MHz

[Other models] ............................................ 87.50 to 108.00 MHz

• 50 dB Quieting Sensitivity (IHF, 100% mod.)

Mono ................................................................. 2.8 µV (20.2 dBf)

• Signal to Noise Ratio (IHF)

Mono/Stereo .............................................................. 73 dB/70 dB

• Harmonic Distortion (1 kHz)

Mono/Stereo ................................................................ 0.5%/0.5%

AM SECTION

• Tuning Range

[U.S.A. and Canada models] .............................. 530 to 1710 kHz

[Asia and General models] ................. 530/531 to 1710/1611 kHz

[Other models] ................................................... 531 to 1611 kHz

GENERAL

• Power Supply

[U.S.A. and Canada models] ............................. 120 V AC, 60 Hz

[Australia model] .............................................. 240 V AC, 50 Hz

[Korea model] ................................................... 220 V AC, 60 Hz

[China model] ................................................... 220 V AC, 50 Hz

[U.K., Russia, and Europe models] .................... 230 V AC, 50 Hz

[Asia and General models]

.............................................. 110-120/220–240 V AC, 50/60 Hz

• Power Consumption

[U.S.A. and Canada models] ................................. 240 W/320 VA

[Other models] ................................................................... 240 W

• Standby Power Consumption

[Except Asia and General models] ...................................... 0.8 W

• Maximum Power Consumption [Asia and General models]

5ch, 10%/THD ................................................................ 530 W

• Dimensions (W x H x D) ................................. 435 x 151 x 318 mm

(17-1/8” x 5-15/16” x 12-1/2”)

• Weight ............................................................. 8.0 kg (17 lbs 10 oz)

* Specifications are subject to change without notice.

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION APPENDIX

ADDITIONAL

English

47 En

Page 52

Index

■ Numerics

1 SOUND MENU .................................... 31, 32

2 INPUT MENU ...................................... 31, 34

2ch Stereo ...................................................... 25

3 OPTION MENU ................................... 31, 35

5ch Stereo ...................................................... 25

■ A

A)DISPLAY SET .......................................... 35

A)INPUT ASSIGN ........................................ 34

A)SPEAKER SET ......................................... 32

A.DELAY ...................................................... 34

A/B/C/D/E, front panel .................................... 3

Adjusting the speaker level ............................ 19

Adjusting the tonal quality ............................ 19

AM tuning ..................................................... 27

AMP, remote control ....................................... 5

ANTENNA terminals ...................................... 6

Audio cable plugs .......................................... 11

Audio delay ................................................... 34

AUDIO jacks ............................................. 6, 11

Audio jacks .................................................... 11

AUDIO L/R (VIDEO AUX) jacks,

front panel ................................................... 3

AUDIO SEL, remote control ........................... 5

AUDIO SELECT ........................................... 18

Audio select ................................................... 36

Audio settings ................................................ 34

Automatic preset tuning ................................ 27

Automatic tuning ........................................... 27

■ B

B)INPUT RENAME ..................................... 34

B)MEMORY GUARD .................................. 35

B)SP LEVEL ................................................. 33

BAND LEVEL TITLE, remote control ........... 5

BAND, front panel .......................................... 3

BASIC SETUP ........................................ 16, 31

Basic setup ..................................................... 31

BASS OUT .................................................... 32

BGV ............................................................... 35

Bluetooth setting ............................................ 36

Bluetooth status message ............................... 44

BT connected, Bluetooth status message ...... 44

■ C

C)AUDIO SELECT ....................................... 36

C)SP DISTANCE .......................................... 33

C)VOLUME TRIM ....................................... 35

Canceled, Bluetooth status message .............. 44

CD Listening ................................................. 22

CD Music Listening ...................................... 22

CENTER ........................................................ 32

Center graphic equalizer ................................ 33

Center speaker ............................................... 32

Center width .................................................. 26

CINEMA DSP indicator .................................. 4

Completed, Bluetooth status message ........... 44

COMPONENT VIDEO jacks .................... 6, 11

Connect error, iPod controlling status

message ..................................................... 44

Connecting a DVD player ............................. 13

Connecting a TV ............................................ 12

Connecting audio components ...................... 13

Connecting speakers ........................................ 9

Connecting the AM antennas ........................ 15

Connecting the Bluetooth Wireless Audio

Receiver .................................................... 14

Connecting the FM antennas ......................... 15

Connecting the power cable .......................... 15

Connecting the Yamaha iPod

universal dock ........................................... 14

Connecting to CD player ............................... 13

Connecting to DVD recorder ......................... 13

Connecting to MD recorder/CD recorder ...... 13

Connecting to the CENTER terminals .......... 10

Connecting to the COMPONENT

VIDEO jacks .............................................11

Connecting to the FRONT A terminals .........10

Connecting to the FRONT B terminals ..........10

Connecting to the HDMI jacks ......................11

Connecting to the MULTI CH INPUT

jacks ...........................................................14

Connecting to the SURROUND terminals ....10

Connecting video components .......................13

Control buttons, remote control .......................5

Creating original SCENE templates ..............23

CROSSOVER ................................................33

Crossover .......................................................33

CT WIDTH ....................................................26

Cursors/ENTER, remote control ......................5

■ D

D)CENTER GEQ ...........................................33

D)DECODER MODE ....................................35

D)PARAM. INI ..............................................36

Decoder indicator .............................................4

Decoder mode ................................................35

Decoder select mode ......................................35

DIGITAL AUDIO COAXIAL jack ...............11

DIGITAL AUDIO OPTICAL jacks ...............11

DIGITAL INPUT COAXIAL assignment .....34

DIGITAL INPUT jacks ....................................6

DIMENSION .................................................26

Dimension ......................................................26

DIMMER .......................................................35

Dimmer ..........................................................35

Disc Listening ................................................22

Disconnected, Bluetooth status message .......44

Disconnected, iPod controlling status

message .....................................................44

Display settings ..............................................35

DISPLAY, remote control ...............................5

DOCK indicator, Front panel display ..............4

Dock Listening ...............................................22

DOCK terminal ................................................6

DSP LEVEL ...................................................26

DSP level ........................................................26

DTS decoder prioritize setting .......................35

DVD Live Viewing ........................................22

DVD Movie Viewing .....................................22

DVD Viewing ................................................22

DVR Viewing ................................................22

Dynamic range ...............................................34

■ E

E)BLUETOOTH ............................................36

E)LFE LEVEL ...............................................34

E)MULTI CH SET .........................................35

EDIT PRESET/TUNING, front panel .............3

Editing sound field parameters ......................26

ENHANCER indicator ..................................... 4

ENHANCER, remote control ..........................5

Enjoying 2-channel sources using

the standard decoders ................................26

Exchanging preset stations .............................28

■ F

F)D.RANGE ..................................................34

FM tuning .......................................................27

FRONT ...........................................................32

FRONT B ....................................................... 32

FRONT B speaker setting ..............................32

Front panel .......................................................3

Front panel display .......................................3, 4

Front speakers ................................................32

■ G

G)AUDIO SET ..............................................34

Game Playing .................................................23

■ H

Hall ................................................................ 25

HDMI ............................................................. 11

HDMI jack, HDMI cable plug ....................... 11

HDMI terminals ............................................... 6

Headphone dynamic range ............................ 34

Headphone LFE ............................................. 34

Headphones indicator ...................................... 4

HP D.R ........................................................... 34

HP LFE .......................................................... 34

■ I

Infrared window .............................................. 8

Infrared window, remote control .....................5

INI.VOL. ....................................................... 34

Initial volume ................................................. 34

Initializing ...................................................... 40

Input assignment ............................................ 34

Input channel and speaker indicators ............... 4

Input channel indicators ................................... 4

Input menu ..................................................... 31

Input rename ..................................................34

Input selector buttons, remote control ............. 5

Input source indicators ..................................... 4

Input source information ............................... 20

INPUT, front panel .......................................... 3

Installing batteries in the remote control ......... 8

iPod connected, iPod controlling status

message ..................................................... 44

iPod control, Status message ......................... 44

■ J

Jazz ................................................................ 25

■ L

LFE indicator ................................................... 4

LFE/Bass out ................................................. 32

Listening to unprocessed input signals ..........26

Low-frequency effect level ............................ 34

■ M

Manual preset tuning ..................................... 28

MANUAL SETUP ........................................ 31

Manual setup .................................................. 31

Manual tuning ................................................ 27

MAX VOL. .................................................... 34

Maximum volume .......................................... 34

MEM.GUARD .............................................. 35

Memory guard ............................................... 35

MEMORY, front panel .................................... 3

MENU, remote control ....................................5

Movie Dramatic ............................................. 25

Movie Spacious ............................................. 25

MULTI CH IN, remote control ....................... 5

MULTI CH INPUT jacks ................................6

Multi channel input setup .............................. 35

Multi-channel sources and sound field

programs with headphones ....................... 26

Multi-information display ................................ 4

Music Disc Listening ..................................... 22

Music Enh. 2ch ..............................................25

Music Enh. 5ch ..............................................25

MUTE indicator ............................................... 4

MUTE TYP. .................................................. 34

Mute type ....................................................... 34

MUTE, remote control .................................... 5

Muting the audio output ................................ 19

■ N

NIGHT indicator .............................................. 4

Night listening mode ..................................... 19

NIGHT, front panel ......................................... 3

NIGHT, remote control ................................... 5

No BT adapter, Bluetooth status message .....44

Numeric buttons, remote control ..................... 5

48 En

Page 53

■ O

Option menu ...................................................31

■ P

Pairing, Bluetooth control ..............................30

PANORAMA .................................................26

Panorama ........................................................26

Parameter initialization ..................................36

PCM indicator ..................................................4

PHONES jack, front panel ...............................3

Placing speakers ...............................................9

Playing video sources in the background .......20

Pop/Rock ........................................................25

PORTABLE (VIDEO AUX) jack,

front panel ...................................................3

Power cable ......................................................6

POWER, remote control ..................................5

PRESET .........................................................40

Preset SCENE templates ................................22

PRESET/TUNING, front panel .......................3

PROG, remote control ......................................5

PROGRAM, front panel ...................................3

■ R

Radio Listening ..............................................22

Rear panel .........................................................6

Remote control .................................................5

Resetting the system .......................................40

RETURN, remote control ................................5

■ S

SCENE ...........................................................21

SCENE 1/2/3/4, front panel .............................3

SCENE 1/2/3/4, remote control .......................5

Searching..., Bluetooth status message ..........44

Selecting audio input jacks .............................18

Selecting preset stations .................................28

Selecting the MULTI CH INPUT

component as the input source ..................18

Selecting the night listening mode .................19

Selecting the SCENE templates .....................21

Set menu .........................................................31

Set this unit to the standby mode ...................15

Setting input source of the customized SCENE

template on the remote control ..................24

Setting remote control codes ..........................39

Setting the speaker impedance .......................40

SIGNAL INFO ...............................................20

Signal information ..........................................31

SILENT CINEMA .........................................26

SILENT CINEMA indicator ............................4

SLEEP indicator ...............................................4

Sleep timer .....................................................20

SLEEP, remote control .....................................5

Sound field programs .....................................25

Sound menu ....................................................31

SP A B indicators .............................................4

SP D.R ............................................................34

SP IMP. ..........................................................40

SP LFE ...........................................................34

Speaker distance .............................................33

Speaker distances ...........................................33

Speaker dynamic range ..................................34

Speaker impedance .........................................40

Speaker level ..................................................33

Speaker LFE ...................................................34

Speaker settings ..............................................32

SPEAKERS terminals ......................................6

SPEAKERS, front panel ..................................3

Specifications .................................................47

STANDBY, remote control .............................5

STANDBY/ON, front panel .............................3

START PAIRING ..........................................36

Start pairing ....................................................36

Straight decoding mode ..................................26

STRAIGHT, front panel ...................................3

STRAIGHT, remote control .............................5

SUBWOOFER OUTPUT jack .........................6

Subwoofer phase ............................................ 33

Supplied accessories ........................................2

SUR. LR ........................................................ 32

SUR.DECODE, remote control ....................... 5

Surround left/right speakers ........................... 32

SWFR PHASE ............................................... 33

■ T

TEST .............................................................. 34

Test tone ......................................................... 34

TONE CONTROL, front panel ....................... 3

Troubleshooting ............................................. 41

Tuner indicators ............................................... 4

TUNING AUTO/MAN’L, front panel ............3

Turning off the power .................................... 15

Turning on the power ..................................... 15

TV control buttons, remote control ................. 5

TV Sports ....................................................... 25

TV Sports Viewing ........................................22

TV Viewing ................................................... 22

TV/AV POWER, remote control ..................... 5

■ U

UNIT .............................................................. 33

Unit ................................................................ 33

Unknown iPod, iPod controlling status

message ..................................................... 44

Using the remote control ................................. 8

Using the VIDEO AUX jacks ........................ 15

Using your headphones .................................. 19

■ V

VIDEO (VIDEO AUX) jack, front panel ........3

Video cable plugs .......................................... 11

VIDEO jacks .............................................. 6, 11

Video jacks .................................................... 11

Virtual CINEMA DSP ................................... 26

VIRTUAL indicator ......................................... 4

VOLUME +/-, remote control .........................5

VOLUME control, front panel ........................ 3

VOLUME level indicator ................................ 4

Volume Trim ................................................. 35

■ Z

Zone B ........................................................... 18

Index

“ASTANDBY/ON” or “fDVD” (example) indicates the name of the parts on the front panel or the remote control. Refer to

“Functional overview” on page 3.

INFORMATION

ADDITIONAL

English

49 En

Page 54

List of remote control codes

Blu-ray Player

Samsung 2137

CD Player

Yamaha 5000, 5013

CD Recorder

Yamaha 5001

DVD

Acoustic Solutions

2078 Aiwa 2055, 2100 Akai 2096 Akura 2076 Alba 2078, 2086 Apex 2027, 2049 Awa 2078 Axion 2078 Brainwave 2096 Brandt 2073, 2085 Broksonic 2060 Bush 2075, 2078, 2112 Centrex 2077 Classic 2078 Clatronic 2075 Coby 2078 C-Tech 2074 CyberHome 2025, 2079, 2091 Daewoo 2092, 2098 Dansai 2096 Daytek 2080, 2089 DEC 2075 Denon 2030, 2102, 2103 Denver 2075, 2076 Diamond 2074 DK Digital 2094 Dual 2078 D-Vision 2096 DVX 2074 Elta 2096 Euroline 2096 Funai 2052, 2058 Global Solutions2074 Global Sphere 2074 Goodmans 2075, 2077, 2078 Grundig 2077, 2098 H&B 2075 Haaz 2074 HE 2078 Hitachi 2032, 2072 Home Electronics

2078 Innovation 2072 Irradio 2134 JDB 2078 JVC 2033, 2045, 2053,

2073, 2099 Kenwood 2030, 2097 Kingavon 2075 Koda 2075 Lawson 2074 Lenco 2075 LG 2084, 2087 Lifetec 2072 Limit 2074 LogicLab 2074 Luxor 2077 Magnavox 2037, 2073, 2075 Magnum 2072

MBO 2078 Medion 2072 Micromaxx 2072 Micromedia 2073 Microstar 2072 Mitsubishi 2035 Mizuda 2075 Mustek 2078 Naiko 2077 Onkyo 2073, 2135 Orava 2075 P&B 2075 Pacific 2074 Panasonic 2030, 2040, 2054,

2057, 2105, 2110

Philips 2019, 2026, 2046,

2073, 2081, 2090 Pioneer 2036, 2082 Proline 2077 Provision 2075 RCA 2031, 2042, 2050,

2051 Red Star 2076 Reoc 2074 Roadstar 2075, 2078, 2086 Rowa 2077 Saba 2085 Sabaki 2074 Samsung 2032, 2041, 2104,

2113 Sansui 2074 Sanyo 2095 ScanMagic 2078 Scientific Labs 2074 Scott 2088 SEG 2074, 2086 Sharp 2034, 2043, 2059,

2093, 2106 Silva 2076 Singer 2074 Skymaster 2074, 2078 Skyworth 2076 SM Electronic 2074, 2078 Sony 2028, 2029, 2039,

2083, 2107 Soundmaster 2074 Soundmax 2074 Standard 2074 Star Cluster 2074 Starmedia 2075 Supervision 2074, 2078 Sylvania 2052, 2058 Synn 2074 TCM 2072 Teac 2074 Tec 2076 Technics 2030 Technika 2096 Technosonic 2096 Tevion 2072, 2074 Thomson 2085, 2109 Tokai 2076 Toshiba 2026, 2044, 2048,

2056, 2073, 2108,

2111 United 2078 Voxson 2078 Wharfedale 2074 Xlogic 2074 Yakumo 2077 Yamada 2077

Yamaha 2000, 2001, 2003,

2030, 2101 Yukai 2078 Zenith 2038, 2047, 2073

DVD Recorder

Apex 2024 JVC 2070 LG 2071 Panasonic 2020, 2065, 2066,

2067 Philips 2019, 2061, 2062,

2063 Pioneer 2021 RCA 2018 Sony 2022, 2064 Toshiba 2068 Yamaha 2023 Yukai 2069

DVD/LD

Pioneer 2036

DVD/VCR

JVC 1017, 2045 LG 1071, 2087 Panasonic 1020, 1072, 2040,

2105 Philips 1025 RCA 1022, 2042 Samsung 1021, 2041, 2104 Sharp 1023, 1073, 2043,

2106 Sony 1019, 1074, 2039,

2107 Toshiba 1024, 1075, 2044,

2108 Zenith 1026, 2047

DVD/DVR

Panasonic 2067 Pioneer 2114 Samsung 2115 Toshiba 2068

DVR

ABS 2132 Alienware 2132 CyberPower 2132 Dell 2132 DIRECTV 2123, 2128, 2129,

2133 DISH Network 2126, 2127 Dishpro 2126 Echostar 2126, 2127 Expressvu 2126 Gateway 2132 GOI 2126 Hewlett Packard2132 Hitachi 2008 Howard Computers

2132 HTS 2126 Hughes 2123, 2128 Humax 2123 Hush 2132 iBUYPOWER 2132 JVC 2126, 2127 Linksys 2132 Media Center PC

2132

Microsoft 2132 Mind 2132 Niveus Media 2132 Northgate 2132 Panasonic 2015, 2016, 2017,

2120

Philips 2117, 2121, 2123,

2128 Pioneer 2012, 2013, 2014 Proscan 2129 RCA 2116, 2124, 2129,

2133 ReplayTV 2118, 2119, 2120 Sharp 2009, 2010 Sonic Blue 2119, 2120 Sony 2005, 2006, 2007,

2122, 2130, 2131,

2132 Stack 10 2132 Stack 9 2132 Systemax 2132 Tagar Systems 2132 Tivo 2116, 2121, 2122,

2123, 2130, 2131 Toshiba 2004, 2125, 2132 Touch 2132 UltimateTV 2133 Viewsonic 2132 Voodoo 2132 Yamaha 2011 ZT Group 2132

HD DVD

Toshiba 2136

iPod

Yamaha 5011

LD Player

Yamaha 2002

Yamaha 5002, 5003, 5004

Tape Deck

Yamaha 5005, 5006

Tune r

Yamaha 5007, 5008, 5009,

5010, 5012, 5014,

5015, 5016, 5017,

5018

Acer 0093 Acme 0207 Acura 0208 ADA 0255 ADC 0206 Admiral 0058, 0205, 0206,

0210, 0211 Adyson 0200, 0207 Agashi 0200 Agazi 0206 AGB 0204 Aiko 0127, 0200, 0207,

0208 Aiwa 0028, 0139, 0229,

0237

Page 55

Akai 0059, 0065, 0127,

0129, 0130, 0200, 0204, 0208, 0209, 0213, 0217, 0218,

0255 Akiba 0209, 0218 Akura 0206, 0209, 0218 Alaron 0200 Alba 0200, 0207, 0208,

0209, 0217, 0218 ALBIRAL 0212 Allstar 0213 Amplivision 0207 Amstrad 0204, 0206, 0208,

0209, 0218 Amtron 0062 Anam 0208 Anam National 0062 Anglo 0208 Anitech 0206, 0208 Ansonic 0203, 0208 AOC 0060, 0061 Apex 0118, 0122, 0132 Arc en Ciel 0216 Arcam 0200 Arcam Delta 0207 Aristona 0213, 0217 ASA 0205, 0211 Asberg 0213 Astra 0208 Asuka 0200, 0206, 0207,

0209, 0218 Atlantic 0200, 0207, 0213,

0217 Atori 0208 Audiosonic 0207, 0208, 0209,

0213, 0216, 0217,

0218 AudioTon 0207 Audiovox 0062 Autovox 0205, 0206, 0207 Awa 0 20 0 Baird 0216 Bang & Olufsen 0205 Basic Line 0208, 0209, 0213,

0218 Bastide 0207 Baur 0217 Beko 0228 Belcor 0060 Bell & Howell 0058, 0064 Benq 0081 Beon 0213, 0217 Bestar 0213 Binatone 0207 Black Star 0214 Blaupunkt 0255 Blue Sky 0209, 0218 Bondstec 0214 Boots 0207 Bradford 0062 Brandt 0216, 0226 Brionvega 0205, 0213, 0217 Britannia 0200, 0207 Brockwood 0060 Broksonic 0138 Bruns 0205 BSR 0215 BTC 0209, 0218 Bush 0177, 0208, 0209,

0210, 0213, 0215,

0216, 0217, 0218,

0230, 0237 Candle 0060, 0061 Capsonic 0206

Cascade 0208 Cathay 0213, 0217 CCE 0127 Celebrity 0059 Centurion 0213, 0217 Century 0205 CGE 0214, 0215 Cimline 0208, 0218 Citizen 0060, 0061, 0062,

0064 City 0208 Clarivox 0212, 0217 Clatronic 0206, 0207, 0208,

0209, 0213, 0214,

0218 CMS 0200 Colortyme 0060, 0061 Concerto 0060, 0061 Concorde 0208 Condor 0200, 0207, 0213 Contec 0200, 0207, 0208 Contec/Cony 0062 Continental Edison

0216 Cosmel 0208 Craig 0062 Crosley 0205, 0214, 0215 Crown 0062, 0063, 0128,

0208, 0213, 0217 CS Electronics 0200, 0207, 0209,

0214, 0218 CTC 0214 Curtis Mathes 0057, 0060, 0061,

0064, 0065 CXC 0062 Cybertron 0209, 0218 Daewoo 0060, 0061, 0120,

0127, 0155, 0193,

0200, 0207, 0208,

0213, 0218, 0238 Dainichi 0200, 0209, 0218 Dansai 0200, 0206, 0213,

0217 Dantax 0217 Daytron 0060, 0061, 0208 De Graaf 0210 Decca 0204, 0207, 0213,

0217 Desmet 0213, 0217 Diamond 0200 Dimensia 0057 Dixi 0208, 0213, 0217 DTS 0208 Dual 0207, 0215, 0216 Dual-Tec 0207, 0208, 0215 Dumont 0060, 0127, 0205,

0207 Durabrand 0126 Dux 0217 Dynatron 0213, 0217 Elbe 0203, 0204, 0212,

0218 Elbe-Sharp 0204 Elcit 0204, 0205 ELECTRO TECH

0208 Electroband 0059 Electrohome 0059, 0060, 0061 Elin 0200, 0207, 0213,

0217 Elite 0209, 0213, 0218 Elman 0215 Elta 0200, 0208 Emerson 0060, 0061, 0062,

0064, 0128, 0205

Envision 0060, 0061 Erres 0213, 0217 ESA 0080 Etron 0208 Euro-Feel 0206 Euroline 0217 Euroman 0200 Euromann 0206, 0207, 0213 Europhon 0200, 0204, 0207,

0213, 0215 Fenner 0208 Ferguson 0212, 0217, 0226 Fidelity 0200, 0207, 0210 Finlandia 0210 Finlux 0204, 0205, 0207,

0213, 0215, 0217 Firstline 0200, 0207, 0208,

0213, 0214 Fisher 0064, 0127, 0128,

0205, 0207, 0215 Flint 0213, 0218 Formenti 0200, 0205, 0207,

0215, 0217 Formenti-Phoenix

0200 Fortress 0205 Frontech 0206, 0208, 0210,

0211, 0214 Fujitsu 0023, 0024, 0025,

0088, 0127 Funai 0033, 0034, 0035,

0036, 0037, 0062,

0206 Futuretech 0062 Gateway 0094 GBC 0208, 0215, 0218 GE 0057, 0060, 0061,

0122, 0147 GEC 0204, 0207, 0211,

0213, 0217 Geloso 0208, 0210, 0215 General Technic 0208 Genexxa 0209, 0211, 0213,

0218 Gibralter 0060 GoldHand 0200 GoldStar 0060, 0061, 0127,

0128, 0200, 0201,

0207, 0208, 0210,

0213, 0214, 0215,

0217 Goodmans 0171, 0201, 0204,

0206, 0208, 0213,

0217, 0240 GPM 0209, 0218 Graetz 0211 Granada 0204, 0207, 0210,

0213, 0217 Grandin 0208, 0209, 0217 Grundig 0128, 0130, 0222,

0236, 0255 Grunpy 0062 Halifax 0200, 0206, 0207 Hallmark 0060, 0061 Hampton 0200, 0207 Hanseatic 0203, 0207, 0208,

0213, 0215, 0217 Hantarex 0204, 0208 Harvard 0062 HCM 0206, 0207, 0208,

0218 Hifivox 0216 Higashi 0200 Hinari 0208, 0209, 0213,

0217, 0218

Hisawa 0209, 0218 Hitachi 0006, 0014, 0015,

0016, 0042, 0060, 0061, 0095, 0105, 0127, 0156, 0179, 0180, 0204, 0207, 0210, 0211, 0215,

0216, 0251 Hornyphon 0213 Hoshai 0209, 0218 Huanyu 0200, 0207 Hygashi 0200, 0207 Hyper 0200, 0207, 0208,

0214, 0215 Hypson 0206, 0207, 0213,

0217 ICE 0127, 0200, 0206,

0207, 0208, 0209,

0213, 0218 ICeS 0200, 0218 IMA 0062 Imperial 0211, 0213, 0214,

0215 Indiana 0213, 0217 Infinity 0063 Ingelen 0211 Ingersol 0208 Inno Hit 0201, 0204, 0207,

0208, 0209, 0213,

0217, 0218 Innovation 0206, 0208 Interbuy 0208, 0214 Interfunk 0205, 0211, 0213,

0214, 0216, 0217 International 0200 Intervision 0206, 0207, 0218 Irradio 0201, 0208, 0209,

0213, 0217, 0218 Isukai 0209, 0218 ITC 0207, 0215 ITS 0200, 0209, 0213,

0218 ITT 0129, 0208, 0211 ITV 0208, 0217 JBL 0063 JC Penney 0057, 0060, 0061 JCB 0059 Jensen 0060, 0061 JVC 0017, 0018, 0019,

0108, 0136, 0153,

0178, 0190, 0213,

0218 Kaisui 0200, 0207, 0208,

0209, 0218 Kamosonic 0207 Kamp 0200, 0207 Kapsch 0211 Karcher 0207, 0208, 0212,

0217 Kawasho 0059, 0060, 0061,

0200 Kendo 0128, 0210 Kennedy 0215 Kenwood 0060, 0061 Kingsley 0200, 0207 Kloss Novabeam

0062 Kneissel 0203 Kolster 0213 Konka 0209, 0218 Korpel 0213, 0217 Korting 0205 Koyoda 0208 KTV 0062, 0127, 0207 Kyoto 0200, 0212

APPENDIX

Page 56

Lenco 0208 Lenoir 0207, 0208 Lesa 0214 Leyco 0206, 0213, 0217 LG 0016, 0038, 0039,

0127, 0128, 0157, 0158, 0163, 0164, 0166, 0188, 0189, 0200, 0201, 0207, 0208, 0210, 0213,

0214, 0215, 0217 Liesenk 0217 Life 0206, 0208 Lifetec 0206, 0208, 0218 Loewe 0063, 0128, 0203,

0204, 0223, 0227 Loewe Opta 0205, 0213, 0217 Logik 0058 Luma 0210, 0217 Lumatron 0210, 0213, 0217 Lux May 0213 Luxman 0060, 0061 Luxor 0201, 0207, 0210 LXI 0057, 0061, 0063,

0064 Magnadyne 0204, 0205, 0214,

0215, 0217 Magnafon 0200, 0204, 0207 Magnavox 0060, 0061, 0063,

0102, 0103, 0150 Magnum 0206, 0208 Majestic 0058 Mandor 0206 Manesth 0206, 0207, 0213,

0217 Marantz 0060, 0061, 0063,

0090, 0213, 0217 Marelli 0205 Mark 0200, 0213, 0217 Matsui 0204, 0207, 0208,

0210, 0213, 0217 Mediator 0213, 0217 Medion 0206, 0208 Megatron 0061 Melectronic 0200, 0207, 0208,

0211, 0213, 0216,

0217 Memorex 0058, 0061, 0064,

0208 Memphis 0208 Metz 0205 MGA 0060, 0061 Micromaxx 0206, 0208 Microstar 0206, 0208 Minerva 0204 Minoka 0213 Mitsubishi 0006, 0015, 0016,

0048, 0060, 0061,

0104, 0112, 0113,

0125, 0205, 0213 Mivar 0200, 0201, 0202,

0203, 0204, 0207 Montgomery Ward

0058 MTC 0060, 0061, 0128,

0200 Multi System 0217 Multitech 0062, 0127, 0128,

0200, 0207, 0208,

0210, 0214, 0215,

0217 Murphy 0200, 0207 NAD 0061 Naonis 0210

NEC 0026, 0053, 0060,

0061, 0096, 0127

Neckermann 0205, 0207, 0210,

0213, 0217, 0255 NEI 0213, 0217 Nesco 0214 NET-TV 0082, 0101 New Tech 0208, 0213 New World 0209, 0218 Nicamagic 0200, 0207 Nikkai 0200, 0206, 0207,

0209, 0213, 0217,

0218 Nikko 0061 Nobliko 0200, 0207 Nogamatic 0216 Nokia 0129, 0211 Nordmende 0205, 0211, 0213,

0216 Nordvision 0217 Oceanic 0211 Olevia 0084 ONCEAS 0207 Onwa 0062, 0218 Orbit 0213 Orion 0126, 0204, 0208,

0213, 0217, 0235 Orline 0218 Orsowe 0204 Osaki 0127, 0206, 0207,

0209, 0218 Osio 0201 Oso 0209, 0218 Osume 0218 Otto Versand 0204, 0207, 0213,

0215, 0216, 0217,

0255 Pael 0200, 0207 Palladium 0207 Panama 0200, 0206, 0207,

0208 Panasonic 0006, 0007, 0063,

0073, 0074, 0097,

0110, 0114, 0137,

0141, 0151, 0162,

0165, 0186, 0204,

0211, 0244, 0245,

0246, 0254 Pathe Cinema 0200, 0203, 0207,

0212, 0215 Pathe Marconi 0212, 0216 Pausa 0208 Perdio 0200 Philco 0060, 0061, 0063,

0128, 0205, 0214,

0215 Philharmonic 0207 Philips 0040, 0060, 0063,

0072, 0115, 0116,

0124, 0130, 0150,

0175, 0184, 0187,

0205, 0207, 0213,

0215, 0217, 0220,

0221, 0232, 0233,

0252, 0253 Philips Magnavox

0124 Phoenix 0200, 0205, 0213,

0217 Phonola 0200, 0205, 0213,

0217 Pilot 0060 Pioneer 0012, 0013, 0060,

0061, 0098, 0109,

0117, 0128, 0181,

0182, 0194, 0195, 0211, 0213, 0216,

0217, 0250 Plantron 0206, 0213 Polaroid 0075 Poppy 0208 Portland 0060, 0061 Prandoni-Prince 0204, 0210 Precision 0207 Prima 0208, 0211 Profex 0208 Profi-Tronic 0213 Proline 0213 Proscan 0057 Prosonic 0200, 0207, 0217 Protech 0206, 0207, 0208,

0213, 0214, 0215,

0217 Proton 0060, 0061 Provision 0217 Pulsar 0060 Pye 0213, 0217 Pymi 0208 Quasar 0152, 0214 Quelle 0201, 0206, 0207,

0213, 0214, 0215,

0217 Radialva 0218 Radio Shack 0064 Radio Shack/Realistic

0057, 0060, 0061,

0062, 0064 Radiola 0213, 0217 Radiomarelli 0204, 0205, 0214 Radiotone 0213 RCA 0057, 0060, 0061,

0091, 0133, 0135,

0147, 0149 Realistic 0064 Revox 0213, 0217 Rex 0206, 0210, 0211 RFT 0203, 0205 Rhapsody 0200 R-Line 0213, 0217 Roadstar 0206, 0208, 0209,

0218, 0237 Robotron 0205 Rowa 0200 RTF 0205 Saba 0204, 0205, 0211,

0216 saccs 0212 Saisho 0204, 0206, 0207,

0208 Salora 0201, 0204, 0210,

0211, 0215 Sambers 0204 Sampo 0060, 0061, 0083,

0101 Samsung 0029, 0030, 0031,

0032, 0044, 0045,

0046, 0047, 0060,

0061, 0065, 0068,

0069, 0071, 0079,

0087, 0127, 0128,

0130, 0144, 0160,

0161, 0170, 0176,

0183, 0185, 0200,

0201, 0206, 0207,

0208, 0213, 0217,

0239, 0241, 0242,

0243 Sandra 0200, 0207 Sansui 0123, 0126, 0213

Sanyo 0020, 0021, 0022,

0049, 0060, 0064, 0127, 0128, 0200,

0203, 0207, 0215 SBR 0217 SCHAUB LORENTZ

0211 Schneider 0207, 0209, 0213,

0215, 0216, 0217,

0218 Scotch 0061 Scott 0060, 0061, 0062 Sears 0057, 0060, 0061,

0064 SEG 0200, 0206, 0207,

0214, 0215, 0217 SEI 0204 SEI-Sinudyne 0204, 0205, 0211 Seleco 0210, 0211, 0215 Sencora 0208 Sentra 0218 Serino 0200 Sharp 0009, 0010, 0011,

0060, 0061, 0066,

0070, 0087, 0111,

0143, 0145, 0167,

0168, 0169, 0198,

0204, 0224, 0247,

0248, 0249 Shogun 0060 Siarem 0204, 0205, 0215 Sicatel 0212 Siemens 0255 Sierra 0213 Signature 0058 Silva 0200 Singer 0205, 0214, 0215 Sinudyne 0204, 0205, 0215,

0217 Skantic 0211 Solavox 0211 Sonoko 0206, 0207, 0208,

0213, 0217 Sonolor 0211 Sontec 0213, 0217 Sony 0041, 0059, 0067,

0085, 0086, 0174,

0196, 0199, 0208,

0219, 0234 Sound & Vision 0209, 0218 Soundesign 0060, 0061, 0062 Soundwave 0213, 0217 SSS 0060, 0062 Standard 0207, 0208, 0209,

0213, 0218 Starlight 0217 Starlite 0062 Stenway 0218 Stern 0210, 0211 Sunkai 0208, 0218 Sunwood 0208, 0213 Superla 0200, 0204, 0207 SuperTech 0200 Supra 0208 Supreme 0059 Susumu 0209 Sutron 0208 Sydney 0200, 0207 Sylvania 0060, 0061, 0063,

0080, 0134, 0142,

0148 Symphonic 0062, 0080 Sysline 0217 Sytong 0200

iii

Page 57

Tandy 0127, 0207, 0209,

0211, 0218 Tashiko 0200, 0207, 0210 Tatung 0127, 0204, 0207,

0213, 0217, 0237 TCM 0206, 0208 Teac 0127 Tec 0207, 0208, 0214,

0215 Techwood 0060, 0061 Teknika 0058, 0060, 0061,

0062 Teleavia 0216 Telecor 0218 Telefunken 0065, 0213, 0216 Telegazi 0218 Teletech 0208, 0214, 0217 Teleton 0207 Televideon 0200 Tensai 0208, 0209, 0213,

0218 Tesmet 0213 Tevion 0206, 0208 Texet 0200, 0207 Thomson 0191, 0192, 0207,

0213, 0216, 0226 Thorn 0212, 0217 TMK 0060, 0061 Tokai 0213 Tokyo 0200, 0207 Toshiba 0027, 0043, 0053,

0054, 0064, 0078,

0089, 0090, 0106,

0107, 0127, 0131,

0140, 0146, 0159,

0197, 0225, 0231,

0237 Towada 0211, 0215 Transtec 0200 Trident 0204 Tristar 0218 Triumph 0204 Uher 0211, 0213 Ultravox 0200, 0205, 0207,

0214, 0215 United 0217 Universum 0127, 0128, 0129,

0201, 0206, 0213,

0214, 0215, 0217 Univox 0212 Vestel 0210, 0211, 0213,

0214, 0215, 0217 Vexa 0208, 0217 Victor 0213 VIDEOLOGIC 0200 Videologique 0200, 0207, 0209,

0218 Videosat 0214 VideoSystem 0213 Videotechnic 0200 Vidtech 0060, 0061 Viewsonic 0076, 0077, 0092,

0099, 0172, 0173 Visiola 0200, 0207 Vision 0213 Vortec 0213, 0217 Voxson 0205, 0210, 0211,

0213 Waltham 0207, 0212 Wards 0057, 0058, 0060,

0061, 0063 Watson 0213, 0217, 0218 Watt Radio 0200, 0207, 0212,

0215 Wega 0205

Weltblick 0213, 0217 Weston 0215 White Westinghouse

0200, 0207, 0217

Yamaha 0000, 0001, 0002,

0003, 0004, 0005,

0060, 0061 Yamishi 0218 Yoko 0200, 0206, 0207,

0208, 0209, 0213,

0217, 0218 Yorx 0209, 0218 Zanussi 0210 Zenith 0058, 0060, 0100,

0105, 0119, 0121,

0154

TV/DVD

Aiwa 0139, 2055 Apex 0132, 2049 Broksonic 0138, 2060 Bush 0230, 2112 JVC 0136, 2053 Panasonic 0137, 0254, 2054,

2110 RCA 0133, 0135, 2050,

2051 Sylvania 0134, 2052 Thomson 0226, 2109 Toshiba 0131, 0231, 2048,

2111

TV/DVD/VCR

Panasonic 0141, 1040, 2057 Samsung 0241, 1070, 2113 Sharp 0143, 1028, 2059 Sylvania 0142, 1041, 2058 Toshiba 0140, 1029, 2056

TV/VCR

Aiwa 0237, 1066 Bush 0237, 1066 Daewoo 0155, 0238, 1038,

1067 GE 0147, 1030 Goodmans 0240, 1069 Grundig 0236, 1062 Hitachi 0156, 1039 JVC 0153, 1036 Magnavox 0150, 1033 Orion 0235, 1065 Panasonic 0151, 1034 Philips 0150, 0232, 0233,

1033, 1062, 1063 Quasar 0152, 1035 RCA 0149, 1032 Roadstar 0237, 1066 Samsung 0144, 0239, 1027,

1068 Sharp 0145, 1028 Sony 0234, 1064 Sylvania 0148, 1031 Tatung 0237, 1066 Toshiba 0146, 0237, 1029,

1066 Zenith 0154, 1037

VCR

Admiral 1008, 1013 Adventura 1005 Aiwa 1005, 1042, 1043,

1044, 1066 Akai 1007, 1043 Akiba 1050 Akura 1043, 1050

Alba 1044, 1050 American High 1004 Amstrad 1042 Anitech 1050 ASA 1045, 1046 Asha 1002, 1014 Asuka 1042, 1045, 1046,

1050 Audio Dynamics1000 Audiovox 1003 Baird 1042, 1043, 1047 Basic Line 1044, 1050 Baur 1046 Beaumark 1002, 1014 Bell & Howell 1001 Blaupunkt 1046, 1048 Broksonic 1012, 1013 Bush 1044, 1050, 1066 Calix 1003 Candle 1002, 1003 Canon 1004 CCE 1006 CGE 1042, 1043 Cimline 1044, 1050 Citizen 1002, 1003 Colortyme 1000 Colt 1006 Craig 1002, 1003, 1006,

1014 Crown 1050 Curtis Mathes 1000, 1002, 1004,

1009 Cybernex 1002, 1014 Daewoo 1005, 1038, 1061,

1067 Dansai 1050 Dantax 1044 DBX 1000 De Graaf 1046, 1049 Decca 1042, 1043, 1046 Denon 1010 Dimensia 1009 Dual 1043, 1046 Dumont 1042, 1046, 1047,

1049 Dynatech 1005 Electrohome 1003 Electrophonic 1003 Elta 1050 Emerson 1003, 1004, 1005,

1012, 1013 Etzuko 1050 Ferguson 1043 Fidelity 1042 Finlandia 1046, 1047, 1049 Finlux 1042, 1043, 1046,

1047, 1049 FIRST LINE 1044, 1045, 1049,

1050 Fisher 1001, 1047 Flint 1044 Formenti/Phoenix

1046 Fuji 1004 Fujitsu 1042 Funai 1005, 1042 Galaxy 1042 Garrard 1005 GBC 1050 GE 1002, 1004, 1009,

1014, 1030 GEC 1046 Geloso 1050 General Technic 1044, 1048 Go Video 1014

GoldHand 1050 Goldstar 1000, 1003, 1042,

1045

Goodmans 1042, 1045, 1050,

1069 Gradiente 1005 Graetz 1043, 1047 Granada 1046, 1047, 1049 Grandin 1042, 1045, 1050 Grundig 1046, 1050, 1062 Hanseatic 1045, 1046 Harley Davidson1005 Harman/Kardon 1000 Harwood 1006 HCM 1050 Headquarter 1001 Hinari 1044, 1050 Hisawa 1044 Hitachi 1007, 1010, 1039,

1042, 1043, 1046,

1049 Hughes Network Systems

1010 Hypson 1044, 1050 Imperial 1042 Inno Hit 1046, 1050 Innovation 1044, 1048 Instant Replay 1004 Interbuy 1045 Interfunk 1046, 1047 Intervision 1042 Irradio 1045, 1050 ITT 1043, 1047 ITV 1045 JC Penney 1000, 1001, 1002,

1003, 1004, 1006 JCL 1004 Jensen 1007 JVC 1000, 1001, 1007,

1011, 1017, 1036,

1043 Kaisui 1050 Karcher 1046 Kendo 1044 Kenwood 1000, 1001, 1007,

1011, 1043 KLH 1006 Kodak 1003, 1004 Korpel 1050 Leyco 1050 LG 1003, 1042, 1045,

1071 Lifetec 1044, 1048 Lloyd’s 1005 Loewe 1048 Loewe Opta 1045, 1046 Logik 1006, 1050 Luxor 1047 LXI 1003 M Electronic 1042 Magnasonic 1047 Magnavox 1004, 1018, 1033 Magnin 1003, 1014 Manesth 1050 Marantz 1000, 1001, 1004,

1046, 1051 Marta 1003 Matsui 1044, 1045 Matsushita 1004 Mediator 1046 Medion 1044, 1048 MEI 1004

APPENDIX

Page 58

Page 59

Page 60

Printed in China WQ96000

Page 61

The letters in circles and the numbers in squares correspond to those in the Owner's Manual.

C D G H I

T PE F

Les lettres dans les cercles et les numéros dans les carrés correspondent à ceux du mode d’emploi.

■ Front panel/Face avant

STANDBY

SPEAKERS

PHONES

/ON

SILENT

CINEMA

EDIT

PRESET/TUNING

TONE

CONTROL

A/B/C/D/E

PROGRAM

PRESET/TUNING

SCENE

STRAIGHT

EFFECT

HTR-6230

VOLUME

MEMORY

BAND

INPUT

NIGHT

TUNING

AUTO/MAN'L

AUX

VIDEO

AUDIO

PORTABLE

K OL N R

J QSBM

Page 62

■ Remote control/Boîtier de télécommande

POWER

POWER POWER

MD/CD-R

STANDBY

TUNER

ABAVC

MUTE

DVD

DTV/CBL

DVR

V-AUX/DOCK

AMP

TV INPUT TV MUTE

SCENE

1234

BAND LEVEL

TITLE

RETURN

REC

STRAIGHT

MULTI CH IN

PROG

ENTER

2341

607

AUDIO SEL

ENHANCER

DISPLAY

NIGHT

TV CH

TV VOL

VOLUME

SUR.DECODE

SLEEP

ENT

s u

Printed in China

WQ96070

YAMAHA HTR-6230 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

INTRODUCTION

Features

Supplied accessories

Front panel

Functional overview

Front panel display

Remote control

Rear panel

Quick start guide

PREPARATION

Preparation of remote control

Connections

Placing speakers

Connecting speakers

Connecting video components

Connecting other components

Using the VIDEO AUX jacks on the front panel

Connecting the FM and AM antennas

Connecting the power cable

Turning on and off the power

Basic setup

BASIC OPERATION

Playback

Basic procedure

Additional operations

Selecting the SCENE templates

Selecting the desired SCENE template

Creating your original SCENE templates

Using remote control on the SCENE feature

Sound field programs

Selecting sound field programs

FM/AM tuning

Overview

FM/AM tuning operations

Preset FM/AM stations

Using iPod™

Control and functions for iPod™

Using Bluetooth™ components

Pairing the Bluetooth™ receiver and your Bluetooth™ component

Playback of the Bluetooth™ component

ADVANCED OPERATION

Set menu

Using set menu

1 SOUND MENU

2 INPUT MENU

3 OPTION MENU

Remote control features

Controlling this unit, a TV, or other components

Setting remote control codes

Advanced setup

ADDITIONAL INFORMATION

Troubleshooting

Glossary

Specifications

Index