Yamaha HTR-5640, HTR 5650 User Manual 2
HTR-5650/HTR-5640
AV Receiver
U
OWNER’S MANUAL
IMPORTANT SAFETY INSTRUCTIONS
10 Ventilation – Slots and openings in the cabinet are provided
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
you to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
1 Read Instructions – All the safety and operating instructions
should be read before the product is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and use instructions
should be followed.
5 Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
6 Attachments – Do not use attachments not recommended
by the product manufacturer as they may cause hazards.
7 Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
8 Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
9 A product and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
product and cart combination to overturn.
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
11 Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
12 Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
13 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
14 Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
15 Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
16 Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
17 Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
18 Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19 Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into
the product,
c) If the product has been exposed to rain or water,
I CAUTION
d) If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in any
way, and
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
20 Replacement Parts – When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or have
the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.
21 Safety Check – Upon completion of any service or
repairs to this product, ask the service technician to
perform safety checks to determine that the product is in
proper operating condition.
22 Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
23 Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as practical.
24 Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA
70, provides information with regard to proper grounding of
the mast and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection
to grounding electrodes, and requirements for the
grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
ELECTRIC
SERVICE
EQUIPMENT
NEC
– NATIONAL ELECTRICAL CODE
MAST
GROUND
CLAMP
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
FCC INFORMATION (for US customers)
1. IMPORTANT NOTICE : DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF” and
“ON”, please try to eliminate the problem by using one
of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
CAUTION II
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this sound system in a well ventilated, cool,
dry, clean place — away from direct sunlight, heat
sources, vibration, dust, moisture, and/or cold.
Allow ventilation space of at least 30 cm on the top,
20 cm on the left and right, and 20 cm on the back
of this unit.
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
4
Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this unit
in a environment with high humidity (i.e. a room with
a humidifier) to prevent condensation inside this unit,
which may cause an electrical shock, fire, damage to
this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may
fall onto this unit and/or this unit may be exposed
to liquid dripping or splashing. On the top of this
unit, do not place:
– Other components, as they may cause damage
and/or discoloration on the surface of this unit.
–
Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall
and liquid may cause electrical shock to the
user and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation.
If the temperature inside this unit rises, it may
cause fire, damage to this unit, and/or personal
injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified
is dangerous and may cause fire, damage to this
unit, and/or personal injury. YAMAHA will not be
held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13
To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
14 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
15 When not planning to use this unit for long periods
of time (i.e. vacation), disconnect the AC power
plug from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
17 Before moving this unit, press STANDBY/ON to set
this unit in standby mode, and disconnect the AC
power plug from the wall outlet.
18
VOLTAGE SELECTOR (China and General models only)
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local main voltage
BEFORE plugging into the AC main supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
standby mode. In this state, this unit is designed to
consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
IMPORTANT
Please record the serial number of this unit in the
space below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through
loud and clear without annoying blaring or distortion – and, most
importantly, without affecting your sensitive hearing.
III CAUTION
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
CONTENTS
INTRODUCTION
CONTENTS ............................................................ 1
FEATURES ............................................................. 2
GETTING STARTED ............................................ 3
Supplied accessories .................................................. 3
Installing batteries in the remote control ...................3
CONTROLS AND FUNCTIONS ......................... 4
Front panel................................................................. 4
Remote control .......................................................... 6
Front panel display .................................................... 8
PREPARATION
CONNECTIONS .................................................... 9
Before connecting components ................................. 9
Connecting video components ................................ 10
Connecting audio components ................................ 12
Connecting the antennas.......................................... 13
Connecting an external decoder .............................. 14
Connecting the speakers ..........................................15
Connecting the power supply cords ........................ 18
Turning on the power .............................................. 18
BASIC SYSTEM SETTINGS ............................. 19
Using the basic menu .............................................. 19
Setting the unit to match your speaker system ........ 21
Setting speaker output levels (SP LEVEL) ............. 21
BASIC OPERATION
PLAYBACK .......................................................... 22
Input modes and indications .................................... 24
Selecting a sound field program ..............................25
DIGITAL SOUND FIELD PROCESSING (DSP)
............................................................................ 28
Understanding sound fields ..................................... 28
Hi-Fi DSP programs ................................................28
CINEMA-DSP ...................................................... 29
Sound design of CINEMA-DSP ............................. 29
CINEMA-DSP Programs ........................................ 29
Sound field effects ................................................... 31
TUNING ................................................................ 32
Presetting stations .................................................... 33
Selecting a preset station ......................................... 35
SLEEP TIMER ..................................................... 36
RECORDING ....................................................... 37
ADVANCED OPERATION
SET MENU ........................................................... 38
Set menu list ............................................................ 38
Adjusting the items on the set menu ....................... 38
SOUND 1 SPEAKER SET (speaker mode settings)
............................................................................. 39
SOUND 2 SP DISTANCE (speaker distance) ........ 41
SOUND 3 LFE LEVEL .......................................... 41
SOUND 4 D. RANGE (dynamic range) ................. 41
SOUND 5 CENTER GEQ
(center graphic equalizer) .................................... 42
SOUND 6 HP TONE CTRL
(headphone tone control) ....................................42
INPUT 1 I/O ASSIGN (input/output assignment) .. 42
INPUT 2 INPUT MODE (initial input mode) ........43
OPTION 1 DISPLAY SET ...................................... 43
OPTION 2 MEM. GUARD (memory guard) ......... 43
OPTION 3 AUDIO MUTE ..................................... 43
OPTION 4 ZONE SET ........................................... 44
REMOTE CONTROL FEATURES ................... 45
Control area ............................................................. 45
Setting the manufacturer code .................................46
Clearing setup manufacturer codes ......................... 46
Controlling other components .................................47
SETTING THE SPEAKER LEVELS ................ 48
Adjusting the volume during playback ................... 48
Using the test tone ................................................... 48
ADDITIONAL INFORMATION
SOUND FIELD PROGRAM PARAMETER
EDITING .......................................................... 49
Changing parameter settings ................................... 49
Digital sound field parameter descriptions .............. 50
TROUBLESHOOTING....................................... 51
GLOSSARY .......................................................... 55
SPECIFICATIONS .............................................. 57
INTRODUCTION
PREPARATION
OPERATION
BASIC
OPERATION
ADVANCED
INFORMATION
ADDITIONAL
1
English
FEATURES
Built-in 6-channel power amplifier
◆ Minimum RMS output power
(0.06% THD, 20 Hz – 20 kHz, 8Ω)
HTR-5650
[U.S.A. and Canada models]
Main: 80 W + 80 W
Center: 80 W
Rear: 80 W + 80 W
Rear center: 80 W
[Other models]
Main: 70 W + 70 W
Center: 70 W
Rear: 70 W + 70 W
Rear center: 70 W
HTR-5640
[U.S.A. and Canada models]
Main: 75 W + 75 W
Center: 75 W
Rear: 75 W + 75 W
Rear center: 75 W
[Other models]
Main: 65 W + 65 W
Center: 65 W
Rear: 65 W + 65 W
Rear center: 65 W
Multi-mode digital sound field processing
◆ Dolby Pro Logic/Dolby Pro Logic II decoder
◆ Dolby Digital/Dolby Digital EX decoder
◆ DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS Neo:6
Decoder
◆ CINEMA DSP: Combination of YAMAHA DSP
technology and Dolby Pro Logic, Dolby Digital or
DTS
◆ Virtual CINEMA DSP
◆ SILENT CINEMA DSP
Sophisticated AM/FM Tuner
◆ 40-Station random access preset tuning
◆ Automatic preset tuning
◆ Preset station shifting capability (Preset editing)
Other features
◆ 96 kHz/24-bit D/A converter
◆ Set menu for optimizing this unit for your Audio/
Video system
◆ Test tone generator for easier speaker balance
adjustment
◆ 6-channel external decoder input
◆ Component video input/output capability
◆ Optical and coaxial digital audio signal jacks
◆ Sleep timer
◆ Remote control with preset manufacturer codes
◆ Zone B capability
HTR-5650
◆ S-video signal input/output capability
◆ Video Conversion (Composite Video ⇔ S Video)
■ About this manual
• This document is the owner’s manual for both the HTR-5650 and HTR-5640. For details on various functions unique
to each model, descriptions given for each model name.
• y indicates a tip for your operation.
• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases
when the button names differ between the main unit and the remote control, the button name on the remote control is
given in parentheses.
• This manual is printed prior to production. Design and specifications are subject to change in part for the reason of
the improvement in operativity ability, and others. In this case, the product has priority.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
“DTS”, “DTS-ES Extended Surround” and “Neo:6” are
trademarks of Digital Theater System, Inc.
2
GETTING STARTED
Supplied accessories
After unpacking, check that the following parts are contained.
Remote control
CODE SET
TRANSMIT
SYSTEM
STANDBY
POWER POWER
DVD
VCR
+
–
HALL
MUSIC
VIDEOTV THEATER
5
/DTS
SUR.
90
LEVEL
TITLE
–
TEST
RETURN
REC
DISC SKIP
POWER
AVTV
SLEEP
MD/CD-R TUNERCD
D-TV/CBL
V-AUX
6CH INPUT
+
VOLUME
TV CHTV VOL
–+–
TV INPUTTV MUTE
MUTE
ENTER-
ROCK
TAINMENT
CONCERT
JAZZ CLUB
3421
MOVIE
MOVIE
THEATER 2
THEATER 1
678
STEREO
6.1/5.1
NIGHT
+10
EFFECT
PRESET/CH
SET MENU
A/B/C/D/E
SELECT
AUDIO
AMP
ENTER
MENU
+
DISPLAY
Batteries (4)
(AAA, R03, UM-4)
75-ohm/300-ohm antenna
adapter (U.K. model)
Installing batteries in the remote control
Insert the batteries in the correct direction by aligning the
+ and – marks on the batteries with the polarity markings
(+ and –) inside the battery compartment.
2
1
3
INTRODUCTION
AM loop antenna
Indoor FM antenna
(U.S.A., Canada, China,
Korea and General models)
(Europe, U.K., Australia and
Singapore models)
■ Notes on batteries
• Change all of the batteries if you notice a decrease in
the operating range of the remote control, that the
indicator does not flash, or the light becoming dim.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline
and manganese batteries) together. Read the packaging
carefully as these different types of batteries may have
the same shape and color.
• If the batteries have leaked, dispose of them
immediately. Avoid touching the leaked material or
letting it come into contact with clothing, etc. Clean the
battery compartment thoroughly before installing new
batteries.
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the manufacturer code and program
any acquired functions that may have been cleared.
1 Press the part marked with a and slide off
the battery compartment cover.
2 Insert the four batteries supplied (AAA, R03,
UM-4) according to the polarity markings on
the inside of the battery compartment.
3 Slide the cover back on so that it snaps into
place.
English
3
Front panel
CONTROLS AND FUNCTIONS
1 32 4 8756 q9
INPUT
RDS MODE/FREQ
STANDBY
/ON
6CH INPUTINPUT MODE
SILENT
PHONES
w r y o
BA
ep
EDIT
PTY SEEK
MODE START
EFFECT
RDS MODE/FREQ
MODE START
EON
PTY SEEK
PRESET/TUNING
PROGRAMSTEREOSPEAKERS
t
EON
A/B/C/D/E
NEXT
CONTROL
SET MENU
iu
a s fd
(U.K. and Europe models only)
1 STANDBY/ON
Turns the unit on, or sets it in standby mode. When you
turn the unit on, you will hear a click and there will be a 4
to 5-second delay before it can reproduce sound.
Standby mode
In this mode, the unit uses a small amount of power in
order to receive infrared-signals from the remote
control.
5 Remote control sensor
Receives signals from the remote control.
6 Front panel display
Shows information about the operational status of the
unit.
7 TUNING MODE (AUTO/MAN’L MONO)
Switches the tuning mode between automatic and manual.
PRESET/TUNING
EDIT
TUNING MODE MEMORY
AUTO/MANUAL MONO
BASS/TREBLE
0
VOLUME
FM/AM
MAN`L/AUTO FM
VIDEO AUX
RAUDIOLVIDEO
2 INPUT MODE
Sets the priority for the types of input signals (AUTO,
DTS, ANALOG) received when one component is
connected to two or more input jacks. You cannot set
priority for an audio source if you have selected 6CH
INPUT as the input source.
3 INPUT
Selects the input source you want to listen to or watch.
4 6CH INPUT
Selects the audio source connected to the 6CH INPUT
jacks. This selection takes priority over sources selected
with INPUT (or the input selector buttons on the remote
control).
4
8 PRESET/TUNING (EDIT)
Switches the function of PRESET/TUNING l / h
between selecting a preset station number and tuning (the
colon (:) turns on or off).
This button is also used to exchange the assignment of
two preset stations with each other.
9 FM/AM
Switches the reception band between FM and AM.
0 MEMORY (MAN’L/AUTO FM)
Stores the current station in memory.
q VOLUME
Controls the output level of all audio channels.
This does not affect the OUT (REC) level.
w SILENT (PHONES jack)
Allows you to enjoy DSP effects when listening with
headphones. When you connect headphones to the
headphone jack, no signals are output to the speakers.
e SPEAKERS A/B
Turns the set of main speakers connected to the A and/or
B terminals on or off.
r STEREO/EFFECT
Switches between normal stereo and DSP effect
reproduction. When you select STEREO, the unit mixes
down all Dolby Digital and DTS signals (except the LFE
channel) as well as those 2-channel signals without
effects, to the main left and right speakers.
t PROGRAM l / h
Select the DSP program.
CONTROLS AND FUNCTIONS
(U.K. and Europe models only)
a RDS MODE/FREQ
Press this button when the unit is receiving an RDS
station, to cycle the display mode among PS mode,
PTY mode, RT mode, CT mode (if the station offers
those RDS data service) and/or frequency display
mode in turn.
s PTY SEEK MODE
Press this button to set the unit in the PTY SEEK
mode.
d PTY SEEK START
Press this button to begin searching for a station after
the desired program type has been selected in the PTY
SEEK mode.
INTRODUCTION
y A/B/C/D/E
Selects preset station groups A to E when the unit is in
tuner mode.
NEXT
Selects the set menu mode when the unit is not in tuner
mode.
u PRESET/TUNING l / h
Select preset station numbers 1 to 8 when a colon (:) is
displayed in the front panel display.
Select the tuning frequency when a colon (:) is not
displayed when the unit is in tuner mode.
SET MENU –/+
Adjust settings on the set menu when the unit is not in
tuner mode.
i CONTROL
Switches between Bass (low-frequency response) control
mode and Treble (high-frequency response) control mode.
o BASS/TREBLE –/+
Increase or decrease low/high-frequency response when
the unit is in Bass/Treble control mode. The sound
changes 2dB each time you press one of these buttons.
Control range: –10 to +10dB
p VIDEO AUX jacks
Inputs for audio and video signals from a portable
external source (game console, etc.). Set the input source
to V-AUX to select source signals from these jacks.
f EON
Press this button to select a radio program type
(NEWS, INFO, AFFAIRS, SPORT) to tune in
automatically.
5
English
CONTROLS AND FUNCTIONS
Remote control
This section describes the remote control controls and
their functions. Make sure that the AMP mode is selected
before starting operation.
1
2
3
CODE SET
POWER POWER
AVTV
MD/CD-R TUNERCD
D-TV/CBL
DVD
TRANSMIT
STANDBY
V-AUX
SYSTEM
POWER
SLEEP
6CH INPUT
8
9
0
q
w
VCR
AMP
e
r
4
5
6
7
+
+
TV CHTV VOL
–
–
TV MUTE
TV INPUT
HALL
JAZZ CLUB
MUSIC
VIDEOTV THEATER
678
5
/DTS
SUR.
NIGHT
90
LEVEL
TITLE
PRESET/CH
–
TEST
RETURN
REC
DISC SKIP
THEATER 1
SELECT
ROCK
CONCERT
3421
MOVIE
6.1/5.1
+10
+
VOLUME
–
MUTE
ENTER-
TAINMENT
MOVIE
THEATER 2
STEREO
ENTER
EFFECT
SET MENU
MENU
A/B/C/D/E
+
DISPLAY
AUDIO
t
y
u
i
o
p
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
2 CODE SET
Used to set up manufacturer codes (see page 46).
3 Input selector buttons
Select the input source and set the remote control to
operate the selected source component.
4 DSP program
Select DSP programs when the remote control is in AMP
mode. Press one of these buttons repeatedly to select a
DSP program within a program group.
5 LEVEL
Selects the effect speaker channel to adjust.
6 Multi control section
Used to change and implement settings.
7 TEST
Outputs a test tone for use when adjusting the speaker
levels.
8 TRANSMIT indicator
Flashes while the remote control is sending signals.
9 STANDBY
Sets this unit in standby mode.
0 SYSTEM POWER
Turns on the power of the unit.
q SLEEP
Sets the sleep timer.
w 6CH INPUT
Selects the audio source connected to the 6CH INPUT
jacks.
e AMP
Switches the function of the same controls between AMP
and the component selected using the input selector
buttons.
r ★/★★
Sets the remote control to operate other components (not
necessarily connected to this unit) without changing this
unit’s input source.
t VOLUME +/–
Increases or decreases the volume level.
6
CONTROLS AND FUNCTIONS
y MUTE
Mutes the sound. Press again to restore the audio output
to the previous volume level.
u 6.1/5.1
Switches the Dolby Digital EX or DTS ES decoder on or
off.
i STEREO/EFFECT
Switches between normal stereo and DSP effect
reproduction. When you select STEREO the unit mixes
down all Dolby Digital and DTS signals (except the LFE
channel) as well as those 2-channel signals without effect
sounds, to the main left and right speakers.
o NIGHT
Sets the unit in night listening mode.
p SET MENU
Selects the set menu mode.
■ Using the remote control
INPUT
STANDBY
/ON
6CH INPUTINPUT MODE
SILENT
BA
EFFECT
PHONES
30° 30°
PRESET/TUNING
A/B/C/D/E
PROGRAMSTEREOSPEAKERS
CONTROL
SET MENU
NEXT
Approximately 6 m (20 feet)
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
VOLUME
PRESET/TUNING
FM/AM
EDIT
TUNING MODEMEMORY
AUTO/MANUAL MONO
MAN`L/AUTO FM
VIDEO AUX
BASS/TREBLE
RAUDIOLVIDEO
■ Handling the remote control
• Do not spill water or other liquids on the remote
control.
• Do not drop the remote control.
• Do not leave or store the remote control in the
following types of conditions:
– high humidity or temperature such as near a heater,
stove or bath;
– dusty places; or
– in places subject to extremely low temperatures.
INTRODUCTION
7
English
CONTROLS AND FUNCTIONS
Front panel display
13
ES
DISCRETEMATRIX
DIGITAL
PCM
VIRTUAL
SILENT
EX
PL
PL
SP
A B
~~~~~~~~~~~~~~
NIGHT
HiFi
V-AUXVCR
DSP
90qw yer uiop
45
D-TV/CBL
DVD
MD/CD-R
t
s
1 Processor indicators
The indicators for the various decoders light up when the
decoders are in use.
2 VIRTUAL indicator
Lights up when using Virtual CINEMA DSP.
e HiFi DSP indicator
Lights up when you select a Hi-Fi DSP sound field
program.
r CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound field
62
7
TUNER CD
VOLUME
MUTE
AUTO
STEREO
CTRTPTYPS
HOLDPTYEON
(U.K. and Europe models only)
SLEEP
MEMORYTUNED
ft
dB
L C R
RLLFE RC RR
a
program.
3 Headphones indicator
Lights up when headphones are connected to the
headphone jack.
t Multi-information display
Shows the current DSP program name and other
information when you are adjusting or changing settings.
4 Input source indicator
Highlights the current input source with a cursor.
y STEREO indicator
Lights up when the unit is receiving a strong signal from
5 Sound field indicator
a FM stereo broadcast while the “AUTO” indicator is lit.
Displays the sound field management the unit is using
when you listen to a DSP sound field program.
u TUNED indicator
Lights up when this unit is tuned to a radio station.
6 AUTO indicator
Shows that this unit is in the automatic tuning mode.
i MEMORY indicator
Flashes to show a station can be stored in memory.
7 MUTE indicator
Flashes while the MUTE function is on.
o SLEEP indicator
Lights up while the sleep timer is on.
8 VOLUME level indicator
Indicates the volume level.
p LFE indicator
Lights up when the input signal contains an LFE signal.
9 PCM indicator
Lights up when this unit is reproducing PCM (pulse code
modulation) digital audio signals.
a Input channel indicator
The indicators for the appropriate sound channels light up
when a digital signal from a source is played back.
0 SILENT indicator
Lights up when headphones are connected and the digital
sound field processor is on.
s RDS indicator (U.K. and Europe models only)
The name(s) of the RDS data offered by the currently
received RDS station light(s) up.
q SP A B indicator
Lights up to indicate which set of main speakers is
selected. Both indicators light up when both sets of
speakers are selected.
EON indicator lights up when an RDS station that offers
the EON data service is being received.
PTY HOLD indicator lights up while searching for
stations in the PTY SEEK mode.
8
w NIGHT indicator
Lights up when the unit is set to night listening mode.
8
CONNECTIONS
Before connecting components
CAUTION
Do not connect this unit or other components to the
mains power until all connections between the
components have been completed.
• Be sure all connections are made correctly, that is to
say L (left) to L, R (right) to R, “+” to “+” and “–” to
“–”. Some components require different connection
methods and have different jack names. Refer to the
operation instructions for each component you wish to
connect to this unit.
• After you have completed all connections, check them
again to make sure they are correct.
• The jack names correspond to the names on the input
selector.
DIGITAL INPUT jacks
(pages 9 – 12)
Audio component jacks
(page 12)
R
L
CD
DIGITAL
INPUT
CD
5
IN
(PLAY)
MD
COAXIAL
/CD-R
OPTICAL
OUT
D-TV/CBL
4
(REC)
MAIN
DVD
3
SURROUND
MD/CD-R
2
SUB
CENTER
WOOFER
MD/CD-R
1
OPTICAL
DIGITAL
OUTPUT
6CH INPUT OUTPUT
This jack is reserved for factory use.
Do not connect any equipment to this jack.
Video component jacks
(pages 10 – 11)
COMPORNENT VIDEO
P
PR
B Y
DVD
A
R
WOOFER
SUB
VIDEOAUDIOAUDIO
L
S VIDEOVIDEO
D-TV
MONITOR OUT
/CBL
B
MONITOR
OUT
TUNER
AM
ANT
GND
S VIDEOVIDEO
75Ω UNBAL.
FM
ANT
R L
DVD
D-TV
/CBL
IN
VCR
OUT
■ Connecting to digital jacks
This unit has digital jacks for direct transmission of
digital signals through either coaxial or fiber optic cables.
You can use the digital jacks to input PCM, Dolby Digital
and DTS bitstreams. Use digital connections if you wish
to enjoy the multi-channel sound track of DVD material,
etc. with DSP effects. All digital input jacks are
acceptable for 96 kHz sampling digital signals.
Note
• The OPTICAL jacks on this unit conform to the EIA standard.
If you use a fiber optic cable that does not conform to this
standard this unit may not function properly.
Speaker terminals
(page 17)
MAIN
A
B
SPEAKERS
REAR
R L
(SURROUND)
CENTER
CENTER
REAR
CENTER
PREPARATION
6CH INPUT jacks
(page 14)
DIGITAL OUTPUT jack
(page 12)
Antenna input terminals
(page 13)
SUBWOOFER OUTPUT
jack (page 17)
All illustrations of the rear panel in this manual are based on the HTR-5650.
The jacks in the shaded area in this illustration are not present on the HTR-5640.
AC OUTLETS
(page 18)
English
9
CONNECTIONS
Connecting video components
Refer to the connection examples on the next page.
■ Types of video jacks
HTR-5650
COMPONENT VIDEO
P
R PB Y
B, PR) and luminance
S VIDEOVIDEO
1 2 3
HTR-5650
1 VIDEO jack
Conventional composite video signal.
2 S VIDEO jack
Transmits color and luminance separately and
achieves high-quality color reproduction.
3 COMPONENT VIDEO jacks
Transmit color difference (P
separately and provide the best quality picture.
Use the commercially available cable type specified for
connecting each jack.
y
• You can designate the input for the COMPONENT VIDEO A
and B jacks to suit your components by using “INPUT 1 I/O
ASSIGNMENT” on the set menu.
HTR-5650
• Signals received through the S VIDEO input jacks can be
converted to composite signals in this unit and output through
its VIDEO MONITOR OUT as well.
• (With the exception of China and General models) Signals
received through the VIDEO jack on this unit can be output
through the S VIDEO MONITOR OUT jack by setting “V
CONV.” in “OPTION 1 DISPLAY SET” on the set menu to
ON.
• When the unit receives signals through both S VIDEO and
VIDEO jacks, signals input through the S VIDEO jack have
priority.
■ Connecting a video monitor
Connect the video input jack on your video monitor to the
MONITOR OUT VIDEO jack.
Note
• If you connect this unit with a source component using
Component video jacks, you also need to connect your video
monitor using Component video jacks.
■ Connecting a DVD player/digital TV/cable
TV
Connect the optical digital audio signal output jack on
your component to the DIGITAL INPUT jack and
connect the video signal output jack on the component to
the VIDEO jack on this unit.
Note
HTR-5640
• The unit has only one DIGITAL INPUT jack, for use with a
DVD player.
y
• Use the AUDIO jacks on this unit for a video component
which does not have optical digital output jack. However,
multi-channel reproduction cannot be obtained with audio
signals input from the AUDIO jacks.
■ Connecting a recording component
Connect the audio signal input jacks on your video
component to the AUDIO OUT jacks on this unit. Then
connect the video signal input jack on the video
component to the VIDEO OUT jack on this unit for
picture recording.
Connect the audio signal output jacks on your component
to the AUDIO IN jacks on this unit. Then connect the
video signal output jack on the component to the VIDEO
IN jack on this unit to play a source from your recording
component.
Note
• Once you have connected a recording component to this unit,
keep its power turned on while using this unit. If the power is
off, this unit may distort the sound from other components.
Signal flow inside this unit
Input
COMPONENT
VIDEO
S VIDEO
VIDEO
Only when “V CONV.” in “OPTION 1 DISPLAY SET”
is set to ON on the set menu.
10
Output
(MONITOR OUT)
B
A
A
O
OPTICAL
OUTPUT
L R
DVD player
AUDIO
OUTPUT
VIDEO
OUTPUT
OPTICAL
OUTPUT
O
L
R
AUDIO
OUTPUT
CONNECTIONS
TV/digital TV/
cable TV
VIDEO
OUTPUT
HTR-5650
DIGITAL
INPUT
CD
COAXIAL
OPTICAL
D-TV/CBL
DVD
MD/CD-R
MD/CD-R
OPTICAL
DIGITAL
OUTPUT
5
4
3
2
1
SURROUND
CD
IN
(PLAY)
MD
/CD-R
OUT
(REC)
MAIN
WOOFER
AUDIO
OUTPUT
AUDIO
R
SUB
6CH INPUT OUTPUT
R
L
CENTER
WOOFER
AUDIO
LR LR
INPUT
COMPORNENT VIDEO
PREPARATION
P
R
B
Y
P
DVD
S VIDEOVIDEO
S VIDEOVIDEO
VIDEO
OUTPUT
A
D-TV
/CBL
B
MONITOR
OUT
TUNER
AM
ANT
GND
75Ω UNBAL.
FM
ANT
VIDEO
INPUT
R
M
VIDEO
INPUT
Video monitorVCR
VIDEOAUDIO
L
DVD
D-TV
/CBL
IN
VCR
OUT
SUB
MONITOR OUT
indicates audio signal direction
L
indicates left analog cables
R
indicates right analog cables
O
indicates optical cables
indicates video signal direction
English
11
CONNECTIONS
Connecting audio components
■ Connecting a CD player
Connect the coaxial digital output jack on your CD player
to the DIGITAL INPUT CD jack on this unit.
y
• Use the AUDIO jacks on this unit for a CD player which does
not have coaxial digital output jack.
■ Connecting a CD recorder or MD
recorder
HTR-5650
Connect the optical digital signal input jack on your CD
recorder or MD recorder to the DIGITAL OUTPUT MD/
CD-R jack on this unit for digital recording.
Connect the optical digital output jack on your CD
recorder or MD recorder to the DIGITAL INPUT MD/
CD-R jack on this unit to play a source from your
recording component.
HTR-5640
Connect the input jacks on your CD recorder or MD
recorder to the MD/CD-R OUT (REC) jacks for analog
recording.
Connect the output jacks on your CD recorder or MD
recorder to the MD/CD-R IN (PLAY) jacks to play a
source from your recording component.
y
• Use the AUDIO jacks on this unit for a CD recorder or MD
recorder which does not have optical digital input or output
jack.
Notes
• Once you have connected a recording component to this unit,
keep its power turned on while using this unit. If the power is
off, this unit may distort the sound from other components.
HTR-5650
• The DIGITAL OUTPUT jack and analog OUT (REC) jacks
are independent. The DIGITAL OUTPUT jack only outputs
digital signals, while the OUT (REC) jacks output analog
signals only.
CD player
CD recorder or
MD recorder
COAXIAL
OUTPUT
C
L
AUDIO
OUTPUT
OPTICAL
OUTPUT
OPTICAL
INPUT
AUDIO
INPUT
R
HTR-5650
O
O
HTR-5650
L
R
indicates signal direction
L
indicates left analog cables
R
indicates right analog cables
C
indicates coaxial cables
O
indicates optical cables
DIGITAL
INPUT
CD
COAXIAL
OPTICAL
D-TV/CBL
DVD
MD/CD-R
MD/CD-R
OPTICAL
DIGITAL
OUTPUT
5
4
3
2
1
CD
IN
(PLAY)
MD
/CD-R
OUT
(REC)
MAIN
SURROUND
WOOFER
AUDIO
R
SUB
6CH INPUT OUTPUT
CENTER
R
L
WOOFER
COMPORNENT VID
P
R
B
P
DVD
VIDEOAUDIO
L
DVD
D-TV
/CBL
IN
VCR
OUT
SUB
MONITOR OUT
A
S VIDEOVIDEO
D-TV
/CBL
B
MONITOR
OUT
TUNER
AM
ANT
GND
S VIDEOVIDEO
75Ω UNBAL.
FM
ANT
12
Connecting the antennas
CONNECTIONS
Both AM and FM indoor antennas are included with this
unit. In general, these antennas should provide sufficient
signal strength.
Connect each antenna correctly to the designated
terminals.
AM loop antenna
(included)
TUNER
AM
ANT
GND
75Ω UNBAL.
FM
ANT
Ground (GND terminal)
For maximum safety and minimum
interference, connect the antenna GND
terminal to a good earth ground. A good
earth ground is a metal stake driven into
moist earth.
Indoor FM
antenna
(included)
■ Connecting the AM loop antenna
1 Set up the AM loop antenna, then connect it
to the terminals on this unit.
PREPARATION
2 Press and hold the tab to insert the AM loop
antenna lead wires into the AM ANT and
GND terminals.
3 Orient the AM loop antenna for the best
reception.
75-ohm/300-ohm antenna adapter (U.K. model only)
12
Open the cover of the
included 75-ohm/300-ohm
antenna adapter.
3
Lead wire
Cut the lead wire and
remove it.
4
Clamp
with
pliers.
Insert the cable wire into the
slot, and clamp it with pliers.
Clamp with
pliers.
Insert the wire
into the slot.
11 (7/16)
8 (5/16)
6 (1/14)
Cut the external sleeve
of the 75-ohm coaxial
cable and prepare it for
connection.
5
Snap the cover into
place.
Unit:
mm (inch)
Notes
• The AM loop antenna should be placed away from this unit.
• The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
A properly installed outdoor antenna provides clearer
reception than an indoor one. If you experience poor
reception quality, an outdoor antenna may improve the
quality. Consult the nearest authorized YAMAHA
dealer or service center about the outdoor antennas.
FREQUENCY STEP switch (China and General
models only)
FM/AM
50kHz/9kHz
100kHz/10kHz
FREQUENCY
STEP
Because the inter-station frequency
spacing differs in different areas, set the
FREQUENCY STEP switch (located on
the rear panel) according to the frequency
spacing in your area.
North, Central and South America:
100 kHz/10 kHz
Other areas: 50 kHz/9 kHz
Before setting this switch, disconnect the
AC power plug of this unit from the AC
outlet.
English
13
CONNECTIONS
VCR
Connecting an external decoder
This unit is equipped with 6 additional input jacks (MAIN
left and right, CENTER, SURROUND left and right and
SUBWOOFER) for discrete multi-channel input from a
component equipped with a multi-channel decoder and 6
channel output jacks such as a DVD/SACD player.
MAIN
SURROUND
SUB
WOOFER
CENTER
6CH INPUT
SUB
WOOFER
OUTPUT
OUT
L R
S VIDEOVIDEO
MONITOR OUT
LR
CENTER SURROUND
SUBWOOFER MAIN
DVD/SACD player
Note
• When you select 6CH INPUT as the input source, the unit
automatically turns off the digital sound field processor, and
you cannot use DSP programs.
14
CONNECTIONS
Connecting the speakers
■ Speakers
This unit has been designed to provide the best soundfield quality with a 6-speaker system, using main left and
right speakers, rear left and right speakers, a center
speaker, and a rear center speaker. If you use different
brands of speakers (with different tonal qualities) in your
system, the tone of a moving human voice and other types
of sound may not shift smoothly. We recommend that you
use speakers from the same manufacturer or speakers
with the same tonal quality.
The main speakers are used for the main source sound
plus effect sounds. They will probably be the speakers
from your present stereo system. The rear speakers are
used for effect and surround sounds. The center speaker is
for the center sounds (dialog, vocals, etc.). The rear center
speaker supplements the rear (left and right) speakers and
provides for more realistic front-to-back transitions.
The main speakers should be high-performance models
and have enough power-handling capacity to accept the
maximum output of your audio system. The other
speakers do not have to be equal to the main speakers. For
precise sound localization, however, it is ideal to use the
models of equivalent performance with the main
speakers.
■ Speaker placement
Refer to the following diagram when you place the
speakers.
Center speaker
Main
speaker (L)
Main speakers
Place the main left and right speakers an equal distance
from the ideal listening position. The distance between
each speaker and each side of the video monitor should
also be the same.
Center speaker
Align the front face of the center speaker with the front
face of your video monitor. Place the speaker as close to
the monitor as possible (such as directly over or under the
monitor) and centrally between the main speakers.
Main speaker (R)
Rear speaker (R)
Subwoofer
1.8 m (6 feet)
Rear center
speaker
Rear speaker (L)
PREPARATION
Use of a subwoofer expands your sound field
It is also possible to further expand your system with the
addition of a subwoofer. The use of a subwoofer is
effective not only for reinforcing bass frequencies from
any or all channels, but also for reproducing the LFE
(low-frequency effect) channel with high fidelity when
playing back Dolby Digital or DTS signals. The
YAMAHA Active Servo Processing Subwoofer System is
ideal for natural and lively bass reproduction.
Rear speakers
Place these speakers behind your listening position,
facing slightly inwards, about 1.8 m (6 feet) above the
floor.
Rear center speaker
Place the rear center speaker in the center between the
rear left and right speakers at the same height from the
floor as the rear speakers.
Subwoofer
The position of the subwoofer is not so critical, because
low bass sounds are not highly directional. However, it is
better to place the subwoofer near the main speakers.
Turn it slightly toward the center of the room to reduce
wall reflections.
Note
• If you do not use any of effect speakers (rear, center and/or
rear center), change the settings of “SOUND 1 SPEAKER
SET” items at the set menu to direct signals to other terminals
you have connected speakers to.
CAUTION
Use magnetically shielded speakers. If these speakers
still create interference with the monitor, place the
speakers away from the monitor.
English
15
CONNECTIONS
■ Connections
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) in accordance with the markers on
this unit, the speakers, and the speaker cables. If the connections are faulty, no sound will be heard from the speakers,
and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass.
CAUTION
• Use speakers with the specified impedance shown on the rear panel of this unit.
• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/
or the speakers.
A speaker cord is actually a pair of insulated cables
10 mm (3/8”)
running side by side. One cable is colored or shaped
differently, perhaps with a stripe, groove or ridge.
1 Remove approximately 10 mm (3/8”) of
insulation from each of the speaker cables.
2 Twist the exposed wires of the cable
together to prevent short circuits.
Red: positive (+)
Black: negative (–)
12
4
3
3 Unscrew the knob.
5
4 Insert one bare wire into the hole in the side
of each terminal.
5 Tighten the knob to secure the wire.
Banana plug
(With the exception of U.K. and Europe models)
■ IMPEDANCE SELECTOR switch
WARNING
Do not change setting of the IMPEDANCE SELECTOR switch when the unit power is switched on, as doing so may
damage the unit. If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the
IMPEDANCE SELECTOR switch may not be fully slid to either position. If this is the case, slide the switch all the
way to either position when this unit is in standby mode. Be sure to move this switch only when this unit is in
standby mode.
y
(With the exception of U.K. and Europe models)
• You can also use banana plug connectors. First, tighten the
knob and then insert the banana plug connector into the end of
the corresponding terminal.
Select the switch position (left or right) according to the impedance of the speakers in your system.
(General model)
Switch
Speaker
Impedance level
position
Main
If you use one/two set(s) of main speakers, the impedance of
each speaker must be 4 Ω/8 Ω or higher.
Left
Center,
The impedance of each speaker must be 6 Ω or higher.
Rear Center,
Rear
MAIN
A OR B :
A+B :
CENTER
:
REAR CENTER
:
REAR
:
IMPEDANCE SELECTOR
SET BEFORE POWER ON
4ΩMIN.
/SPEAKER
8ΩMIN.
/SPEAKER
6ΩMIN.
/SPEAKER
6ΩMIN.
/SPEAKER
6ΩMIN.
/SPEAKER
MAIN
A OR B :
A+B :
16ΩMIN.
CENTER
:
REAR CENTER
:
REAR
:
8ΩMIN.
8ΩMIN.
8ΩMIN.
8ΩMIN.
/SPEAKER
/SPEAKER
/SPEAKER
/SPEAKER
/SPEAKER
Right
Main*
Center,
If you use one/two set(s) of main speakers, the impedance of
each speaker must be 8 Ω/16 Ω or higher.
The impedance of each speaker must be 8 Ω or higher.
Rear Center,
Rear
* [Canada model only]
IMPEDANCE SELECTOR
switch
When the switch is set to right, you cannot use “A+B”.
16
Loading...