DVD AUDIO/VIDEO SA-CD PLAYER
LECTEUR DE DVD AUDIO/VIDEO SA-CD
DVD-S2500
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
G
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
Important Note
DK
Advarsel:
Laserrudstråling ved åbning når sikkerhesafbrydere er ude
af funktion. Undgå u tsættelse for stråling.
Bemærk:
Netafbryderen STANDBY/ON er sekundært indkoblet og
afbryder ikke strømmen fra nette. Den indbyggede netdel er
derfor tilsluttet til lysnettet så længe netstikket sidder i
stikkontakten.
N
Observer:
Nettbryteren STANDBY/ON er sekundert innkoplet. Den
innebygdenetdelen er derfor ikke frakoplet nettet så lenge
apparatet er tilsluttet nettkontakten.
S
Klass 1 laserapparat
Varning!
Om apparaten används på annat sätt än i denna
bruksanvisning specificerats, kann användaren utsättas för
laserstrålning, som översjruder gränsen för läserklass 1.
Observera!
Strömbrytaren STANDBY/ON är sekundärt kopplad och
inte bryter strömmen fråan nätet Den inbyggda nätdelen är
därför ansluten till elnätet så länge stickproppen sitter i v
ägguttaget.
SF
Luokan 1 laserlaite + Klass 1 laserapparat
Varoitus!
Laitteen käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle lasersäleilille.
Huom.
Toiminnanvalitsin STANDBY/ON on kytketty
toisiopuolelle, eikä se kytke laitetta irti sähköverkosta.
Sisäänrakennettu verkko-osa on kytkettynä sähköverkkoon
aina silloin, kun pistoke on pistorasiassa.
VARO!
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET
ALTTIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO
SÄTEESEEN.
VARNING!
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH
SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN.
Important Note for Users in the UK
Mains plug
This apparatus is fitted with an approved 13 Amp plug.To
change a fuse in this type of plug proceed as follows:
1 Remove fuse cover and fuse.
2 Fix new fuse which should be a BS1362 5 Amp,
A.S.T.A. or BSI approved type.
3 Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it
should be cut off and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of
5 Amp. If a plug without a fuse is used, the fuse at the
distribution board should not be greater than 5 Amp.
Note:The severed plug must be disposed of to avoid a
possible shock hazard should it be inserted into a 13 Amp
socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the following
code: blue = neutral (N), brown = live (L).
As these colours may not correspond with the colour
markings identifying the terminals in your plug, proceed as
follows:
• Connect the blue wire to the terminal marked N or
coloured black.
• Connect the brown wire to the terminal marked L or
• Do not connect either wire to the earth terminal in the
Before replacing the plug cover, make certain that the cord
grip is clamped over the sheath of the lead - not simply over
the two wires.
Copyright in the U.K.
Recording and playback of material may require
consent. See Copyright Act 1956 and The Performer’s
Protection Acts 1958 to 1972.
coloured red.
plug, marked E (or e) or coloured green (or green and
yellow).
i
General information
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
ATTENTION
L’emploi de commandes, de réglages ou un choix de
procédures différents des spécifications de cette brochure
peut entraîner une exposition à d’éventuelles radiations
pouvant être dangereses.
ACHTUNG
Die Verwendung von Bedienungselementen oder
Einstellungen oder die Durchführung von
Bedienungsvorgängen, die nicht in dieser Anleitung
aufgeführt sind, kann zu einem Kontakt mit gefährlichen
Laserstrahlen führen.
OBSERVERA
Användning av kontroller och justeringar eller genomförande
av procedurer andra än de som specificeras i denna bok kan
resultera i att du utsätter dig för farlig strålning.
ATTENZIONE
Uso di controlli o regolazioni o procedure non specificamente
descritte può causare l’esposizione a radiazioni di livello
pericoloso.
PRECAUCIÓN
El uso de los controles o los procedimientos de ajuste o
utilización diferentes de los especificados en este manual
pueden causar una exposición peligrosa a la radiación.
VOORZICHTIG
Gebruik van bedieningsorganen of instellingen, of uitvoeren
van handelingen anders dan staan beschreven in deze
handleiding kunnen leiden tot blootstelling aan gevaarlijke
stralen.
The unit is not disconnected from the AC power source as long
as it is connected to the wall outlet,even if this unit itself is
turned off.This state is called the standby mode.In this state,this
unit is designed to consume a very small quantity of power.
L ’appareil n ’est pas isolé de la source d ’alimentation aussi
longtemps qu ’il reste branché sur une prise murale,même
lorsqu ’il est éteint.Il est alors dit en mode «Veille ».Dans ce
mode, l ’appareil consomme très peu de courant.
Das Gerät ist nicht vom Netz getrennt, solange der Netzstecker
noch mit der Wandsteckdose verbunden ist, selbst wenn das
Gerät ausgeschaltet wurde. Dieser Betriebszustand wird als
Bereitschaftsmodus bezeichnet. In diesem Zustand nimmt das
Gerät eine sehr geringe Menge Strom auf.
Enheten är inte urkopplad från nätet så länge som den är
ansluten till vägguttaget även om enheten i sig självt är
avstängd. Detta kallas för beredskapsläge och i detta tillstånd
konsumerar apparaten minimalt med ström.
L’unità non è scollegata dall’impianto elettrico di casa sintanto
che rimane collegata ad una presa di corrente anche se è spenta.
Questo modo viene chiamato “modo di attesa”. In esso, l’unità
consuma una quantità molto bassa di energia per mantenere in
memoria le impostazioni da voi fatte.
Aunque el propio aparato se encuentre apagado, éste no se
desconectará de la fuente de CA siempre que se mantenga
enchufado a la toma de corriente. Este estado recibe el nombre
de “modo de espera”. En este estado, este aparato ha sido
diseñado para consumir una cantidad muy pequeña de energía.
De stroomtoevoer naar het toestel is niet afgesloten zolang de
stekker nog in het stopcontact zit, zelfs niet als het toestel zelf
uitgeschakeld is. Deze toestand wordt “standby” (waak- of
paraatstand) genoemd. Het toestel is ontworpen om in deze
toestand
CAUTION
- Visible and invisib
le laser
radiation when open. Avoid exposure to beam.
CAUTION
WHEN OPEN. AVOID EXPOSURE TO BEAM.
ADVARSEL
VED ÅBNING. UNDGÅ UDSÆTTELSE FOR STRÅLING.
ADVARSEL
NÅR DEKSEL ÅPNES. UNNGÅ EKSPONERING FOR
STRÅLEN.
VARNING
NÄR DENNA DEL ÄR ÖPPNAD. BETRAKTA EJ
STRÅLEN.
VARO!
JA NÄKYMÄTT ÖMÄLLE LASER SÄTEILYLLE. ÄLÄ
KATSO SÄTEESEEN..
VORSICHT
LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET..
NICHT DEM STRAHL AUSSETSEN.
DANGER
WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM.
ATTENTION
INVISIBLE EN CAS D’OUVERTURE. EXPOSITION
DANGEREUSE AU FAISCEAU.
VISIBLE AND INVISIBLE LASER RADIATION
SYNLIG OG USYNLIG LASERSTRÅLING
SYNLIG OG USYNLIG LASERSTRÅLING
SYNLIG OCH OSYNLIG LASERSTRÅLNING
AVATTAESSA OLET ALTTIINA NÄKYVÄLLE
SICHTBARE UND UNSICHTBARE
VISIBLE AND INVISIBLE LASER RADIATION
RAYONNEMENT LASER VISIBLE ET
ii
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this sound system in a well ventilated, cool, dry,
clean place — away from direct sunlight, heat sources,
vibration, dust, moisture, or cold. In a cabinet, allow
about 2.5cm (1 inch) of free space all around this unit
for adequate ventilation.
3 Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes
from cold to hot, nor locate this unit in an environment
with high humidity (i.e., a room with a humidifier) to
prevent condensation inside this unit, which may cause
an electrical shock, fire, damage to this unit, and/or
personal injury.
5 Avoid installing this unit in a location where foreign
objects may fall onto this unit or where this unit may be
exposed to liquid dripping or splashing. On the top of
this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e., candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall,
spilling the liquid and causing an electrical shock to
the user and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
Do not use excessive force on switches, knobs and/or cords.
9
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Use only the voltage specified on this unit. Using this
unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or
personal injury. YAMAHA will not be held responsible
for any damage resulting from use of this unit with a
voltage other than as specified.
13 To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
14 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be opened
for any reason.
15 When not planning to use this unit for long periods of
time (i.e., vacation), disconnect the AC power plug
from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
17 Before moving this unit, press STANDBY/ON to set
the unit in standby mode, then disconnect the AC
power plug from the wall outlet.
18 Place this unit on a flat, hard and stable surface.
19 There must be sufficient room in front of the player for
the disc tray to be opened.
20 The mechanical parts of the set contain self-lubricating
bearings and must not be oiled or lubricated.
The unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off. This state is called the standby
mode. In this state, this unit is designed to consume a
very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
NOTE:
Pictures shown maybe different between countries.
Never make or change connections with the power switched
on.
When playing DTS encoded CDs, excessive noise will be
heard from the analog stereo outputs. To avoid possible
damage to the audio system, the consumer should take
proper precautions when the analog stereo outputs of the
player are connected to an amplification system. To enjoy
DTS Digital Surround™ playback, an external 5.1-channel
DTS Digital Surround™ decoder system must be connected
to the digital output of the player.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only
a qualified service person should remove the cover or
attempt to service this device.
CAUTION
VISIBLE AND INVISIBLE LASER RADIATION WHEN
OPEN. AVOID EXPOSURE TO BEAM.
This unit emits visible laser radiation when open. Avoid
direct eye exposure to beam.
When this unit is plugged into a wall outlet, do not place
your eyes close to the opening of the disc tray and other
openings or look inside.
Parental Control ............................................................ 29
Activating/deactivating Parental Control ....................... 29
Country ........................................................................... 29
Changing the four-digit PIN..........................................29
If you forget your four-digit code................................... 29
Troubleshooting30
Specifications31
English
1
Introduction
Thank you for purchasing the YAMAHA DVD
AUDIO/VIDEO SA-CD player. This Owner’s Manual
explains its basic operations.
Patent information
Manufactured under license from
Dolby Laboratories.
“Dolby”, “Pro Logic”, and the
double-D symbol are trademarks of
Dolby Laboratories.
“DTS” and “DTS Digital Surround”
are registered trademarks of Digital
Theater Systems, Inc.
“DCDi” is a trademark of Faroudja, a
division of Genesis Microchip, Inc.
HDMI, the HDMI logo and HighDefinition Multimedia Interface are
trademarks or registered trademark of
HDMI Licensing LLC.
This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be
authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
“i.LINK” and the “i.LINK” logo are trademarks of
Sony Corporation.
This product complies with the following i.LINK
interface specifications:
1. IEEE Std 1394a-2000, Standard for a High
Performance Serial Bus
2. Audio and Music Data Transmission Protocol 2.1
Following the standard for AM824 sequence adaptation
layers, the product is compatible with IEC60958
bitstream, DVD-A and SA-CD media.
Playable disc formats
This unit can play the disc types associated with the
logos shown below. (Do not attempt to load any other
type of disc into the unit, or the unit may be damaged.)
This manual refers to disc types using the following
symbols:
DVD-AudioDVD-VideoVideo CD
DVD-A
SA-CD
(Super Audio CD)
SA-CD
VCD
*1icon includes Super Video CD.
DVD-V
Audio CDMP3
CD
*1
VCD
MP3
Notes:
This unit is designed for use with SA-CD, DVD-Video,
–
DVD-Audio, Video CD, Super Video CD, Audio CD,
CD-R and CD-RW (MP3 and JPEG supported),
DVD+R and DVD+RW, DVD-R and DVD-RW.
– CD-R and CD-RW discs cannot be played unless they
have been finalized.
– DVD+R and DVD+RW discs cannot be played
unless they have been finalized.
– DVD-R and DVD-RW discs must be recorded in
Video format and must be finalized.
– Some discs cannot be played depending on disc
characteristics or recording conditions.
– Be sure to use only CD-R and CD-RW discs from
reliable manufacturers.
– Dolby Digital, DTS Digital Surround, and MPEG
digital audio are supported.
– PAL and NTSC are supported.
– This unit features the PAL and NTSC video system
converting function to allow you watching the
different types of video discs on one TV (see “TV
System (NTSC/PAL conversion)” on page 15).
Do not use any non-standard shaped discs (heart, etc.).
–
– Do not use discs that have tape, scales, or paste on
them or damage to the unit may result.
– Do not use discs with surfaces printed by a
commercial label printer.
– Some DVD discs require specific features or allow
only limited function during playback.
– Prohibited mark may appear on the TV screen to
indicate that a function is unavailable.
– Photo CD, CD-ROM, DVD-ROM, DVD-RAM, CDV
and nonstandard CD discs cannot be played on this
unit.
SUPER VIDE
DIGITAL VIDE
O
O
2
Region management
information
Introduction
English
Installing batteries in the
remote control
The unit is designed to support the Region Management
System. Check the regional code number on the disc
package. If the number does not match the unit’s region
number (see table below, or see back of unit), the unit
may be unable to play the disc.
Model
U.S.A. model
U.K. and
Europe models
Australia
model
Region
number of
the unit
11
22
4
Discs that can be
played (Example)
ALL
ALL
ALL
4
Supplied accessories
Check your package to make sure it contains the
following items:
Remote controlBatteries (x2) (AA, R6, UM-3)
Insert the batteries in the correct direction by aligning
the “+” and “–” marks on the batteries with the polarity
markings “+” and “–” inside the battery compartment.
1 Remove the back cover.
2 Insert the two supplied batteries (AA, R6, UM-3) into
the battery compartment.
3 Close the back cover.
Replace worn batteries
Worn batteries limit the operating range of the remote
control. Replace both batteries at the same time.
• Replace both batteries if you notice a decrease in the
operating range of the remote control.
• Do not use old batteries with new ones.
• Do not use different types of batteries (such as
alkaline and manganese) together. Read the battery
packaging carefully. Different types of batteries may
be the same shape or color.
• If the batteries leak, dispose of them immediately.
Avoid touching the leaked material or letting it come
into contact with clothing, etc. Clean the battery
compartment thoroughly before installing new
batteries.
Audio/Video cablePower cable
3
Introduction
Using the remote control
Remote control
sensor
Point the remote control at the
sensor, within approximately 6 m
30
Handling the remote control
• Do not spill water or other liquids on the remote
control.
• Do not drop the remote control.
• Do not leave or store the remote control in the
following types of conditions:
– high humidity such as near a bath
– high temperature such as near a heater or stove
– extremely low temperature
– dusty places
(20 feet) of the unit.
30
Maintenance
Cleaning the cabinet
• Use a soft cloth slightly moistened with a mild detergent
solution. Do not use a solution that contains alcohol,
spirits, ammonia or abrasives.
Cleaning discs
• When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center out. Do not wipe in
a circular motion.
• Do not use solvents such as benzene, thinner,
commercial cleaners, or anti-static spray designed for
analog records.
4
Front panel
STANDBY/ON
–turns on this unit or sets it to the
standby mode
Disc tray
Functional Overview
English
s STOP
– stops playback
b
–moves to the previous chapter or track
a
–moves to the next chapter or track
DVD-AUDIO indicator
–lights up when the unit detects DVD-Audio
signals
SA-CD indicator
–lights up when the unit detects SA-CD signals
MULTI CH indicator
–lights up when you play multi-channel audio
source
HDMI indicator
–lights up when the unit is capable of outputting
signals from the HDMI (High Definition
Multimedia Interface) terminal
i.LINK indicator
–lights up when an AV receiver selects i.LINK
(IEEE1394)
e PAUSE
– pauses playback
h PLAY
– starts playback
Front panel display
– shows information about the
operational status of the unit
PROGRESSIVE indicator
– lights up when the unit enters
PROGRESSIVE mode
AUDIO DIRECT indicator
– lights up when you enter the AUDIO
DIRECT mode by pressing the AUDIO
DIRECT button on the remote control
during audio disc playback
DOWN MIX indicator
– lights up when you play the discs that
allow down mixing of the multi-channel
audio sources
OPEN/CLOSE
– opens or closes the disc tray
5
Functional Overview
Rear panel
HDMI output terminal
–connect to the HDMI jack on a
HDMI-compatible AV component
SCAN MODE switch
–switches the component video output
signals between progressive and
interlace
– connect to a standard AC outlet
AC IN (Main-inlet)
COMPONENT video jacks
–connect to an AV receiver with Y P
P
R inputs
COAXIAL digital audio output
–connect to the audio input jack on
digital (coaxial) audio equipment
AV terminal
–connect to a SCART cable
S VIDEO output
–connect to an S-Video input jack on
your AV receiver
B
OPTICAL digital audio output jack
– connect to the audio input jack on digital
– connect to audio inputs on your AV receiver
6CH DISCRETE audio output jacks
– connect to an AV receiver with 6-ch discrete
– connect to the i.LINK jack on an
i.LINK-compatible component
MIXED 2CH audio output jacks
i.LINK connectors
(optical) audio equipment
or stereo system
audio input jacks
VIDEO output (composite video
out)
–connect to the video input jack on your
AV receiver
Caution: Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause
permanent damage to the unit.
6
Remote control
– turns the power of this unit ON or
enters standby mode
0-9 numeric buttons
SUBTITLE
– selects subtitle languages
AUDIO
– selects audio languages and formats
ANGLE
– selects DVD camera angles
ZOOM
– enlarges video images
RETURN/RESUME
– displays the previous menu or
resumes playback
knlh
– (left/right/up/down) selects an item
in the menu
ENTER/OK
– acknowledges menu selection
MENU
– accesses the menu of a DVD disc
b
– searches backward*/accesses a
previous chapter or track
a
– searches forward*/accesses the
next chapter or track
Functional Overview
English
DIMMER
–adjusts the display brightness
AUDIO DIRECT
–switches video output on and off
during audio disc playback
SOUND MODE
–selects the required sound mode
• for SA-CD: CD, Stereo, or Multichannel (if available)
• for DVD/VCD: Stereo, Dolby
Surround compatible, 3D sound, or
Multi-channel
PAGE
–turns pages of the DVD-Audio still
pictures
TITLE/CHAP
–selects title or chapter
STATUS
– displays current playback information
on the front panel display and on the
status window on screen
ON SCREEN
–accesses or removes the player’s On-
screen menu
STOP (s)
–stops playback
PLAY (h)
–starts playback
PAUSE (e)
–pauses playback temporarily/
frame-by-frame playback
MUTE
–disables or enables sound output
REPEAT
–repeats chapter, track, title, disc, etc.
A-B
–repeats a specific segment
SHUFFLE
–plays tracks/chapter in random order
SCAN
–plays the first 10 seconds of each
track/chapter within a disc
* Press and hold button for about two seconds.
7
Loading...
+ 24 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.