Yamaha CD-S700 Owners Manual
Compact Disc Player
RTL
OWNER’S MANUAL
MANUAL DE INSTRUCCIONES
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at least
10 cm (3 15/16 in) on the top, 10 cm (3 15/16 in) on the left
and right, and 10 cm (3 15/16 in) on the back of this unit.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign objects may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cables.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury.
Yamaha will not be held responsible for any damage resulting
from use of this unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cable
disconnected from a wall outlet or the unit during a lightning
storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the power cable from the wall
outlet.
16 Install this unit near the wall outlet and where the power cable
can be reached easily.
17 Be sure to read the “TROUBLESHOOTING” section in this
manual on common operating errors before concluding that
this unit is faulty.
18 Before moving this unit, press POWER to turn off this unit
and then disconnect the power cable from the wall outlet.
19 The batteries shall not be exposed to excessive heat such as
sunshine, fire or like.
20 VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
into the wall outlet. Voltages are:
.....................................AC 110/120/220/230-240 V, 50/60 Hz
As long as this unit is connected to the wall outlet, it is
not disconnected from the AC power source even if
you turn off this unit by POWER.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a qualified
service person should remove the cover or attempt to service this
device.
DANGER
This unit emits visible laser radiation when open. Avoid direct eye
exposure to beam. When this unit is plugged into the wall outlet, do
not place your eyes close to the opening of the disc tray and other
openings to look into inside.
The laser component in this product is capable of
emitting radiation exceeding the limit for Class 1.
i En
INTRODUCTION
FEATURES.............................................................2
SUPPLIED ACCESSORIES .................................2
CONTROLS AND FUNCTIONS .........................3
Front panel.................................................................3
Front panel display .................................................... 4
Remote control...........................................................5
Installing batteries in the remote control...................6
Using the remote control ...........................................6
PREPARATION
CONNECTIONS ....................................................7
Connecting your amplifier......................................... 7
Connecting the supplied power cable........................8
Connecting USB devices........................................... 8
CONTENTS
PREPARATIONINTRODUCTION
OPERATION
BASIC OPERATION............................................. 9
Starting playback....................................................... 9
Pausing playback.....................................................10
Stopping playback ................................................... 10
Turning off the power..............................................10
Playing back a desired track....................................10
To improve audio quality (PURE DIRECT mode)
............................................................................. 10
Skipping to the beginning of a desired track ........... 11
Advancing or reversing playback rapidly................ 11
Changing front panel display................................... 12
Changing the brightness of the front panel display
............................................................................. 12
RANDOM-SEQUENCE PLAY .......................... 13
REPEAT PLAY ....................................................13
Repeating a selected item ........................................ 13
Repeat A-B .............................................................. 14
PROGRAM PLAY ...............................................15
Stopping program playback..................................... 16
Clearing programmed track .....................................16
ADDITIONAL INFORMATION
NOTES ABOUT DISCS/MP3, WMA FILES .... 17
TROUBLESHOOTING.......................................19
SPECIFICATIONS .............................................. 20
OPERATION
INFORMATION
ADDITIONAL
■ About this manual
• y indicates a tip for your operation.
• In this manual, audio CDs are referred to as “Audio CD”, MP3/WMA discs as “Data Disc”, and MP3/WMA files
stored on the USB device as “USB”.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of
improvements, etc. In case of differences between the manual and the product, the product has priority.
English
1 En
INTRODUCTION
FEATURES
◆ Optical Digital Output
◆ Coaxial Digital Output
◆ CD-R, CD-RW Disc Playability
(For details, refer to page 17.)
◆ MP3, WMA Disc Playability
◆ MP3, WMA File Playability Stored on USB Device
SUPPLIED ACCESSORIES
Please check that you received all of the following parts:
Remote control RCA stereo cable
Batteries (× 2)
(AA, R6, UM-3)
◆ Program Play (Audio CD only)
◆ Random-Sequence Play
◆ Single Track/Entire Disc Repeat Play
◆ Repeat A-B Play (Audio CD only)
◆ Adjustable Display Information and Brightness
◆ PURE DIRECT Function
Power cable
2 En
Front panel
CONTROLS AND FUNCTIONS
INTRODUCTION
1 POWER
Press to turn the power to ON/OFF.
y
The POWER indicator above lights up when this unit is turned
on.
2 USB port
Connect your USB device. See page 8 for details.
3 PURE DIRECT
Turn PURE DIRECT mode on or off to improve audio
quality.
y
The PURE DIRECT indicator above lights up when this unit is in
PURE DIRECT mode. See page 10 for details.
4 Disc tray
Load a disc.
5 (Open/Close)
Open or close the disc tray.
6 / (Skip/Search backward),
/ (Skip/Search forward)
/ : Skip to the next track.
/ : Skip back to the beginning of the current
track.
/ (twice): Skip to the previous track.
Press and hold / or / to search
backward/ forward.
y
Each time you press and hold / or / , the
search speed increases by 2 levels.
7 (Play)
Start playback.
8 (Pause)
Pause playback. Press or to resume playback.
9 (Stop)
Stop playback.
0 USB indicator
Lights on/off when this unit is in USB/disc mode, and
blinks when this unit is reading the USB device.
A Front panel display
Shows the current status of this unit.
B Remote control sensor
Receives signals from the remote control.
English
3 En
CONTROLS AND FUNCTIONS
Front panel display
Audio CD
Data Disc USB
1 Lights up the icon for the selected playback mode.
2 Shows the time displays. (Refer to page 12.)
3 Shows the track number selected or being played back.
4 Shows the file number.
5 Lights up when this unit is in disc mode (refer to page 9) and
also when an Audio CD is recognized on the tray.
6 Lights up when MP3 file is played back.
7 Lights up when WMA file is played back.
4 En
Remote control
CONTROLS AND FUNCTIONS
1 Infrared signal transmitter (p. 6)
Send infrared signals to this unit.
2 CD/USB (p. 9)
Switch between disc mode and USB mode.
3 DIMMER (p. 12)
Select brightness level for the front panel display.
4 Numeric buttons (p. 10)
Select a track directly.
5 PROGRAM (p. 15)
Turn program mode on or off.
6 / (Search backward/forward) (p. 11)
Search tracks backward/forward.
7 / (Skip backward/forward) (p. 11)
Skip to the next/previous track or skip back to the
beginning of the current track.
8 OPEN/CLOSE (p. 9)
Open or close the disc tray.
9 PURE DIRECT (p. 10)
Turn PURE DIRECT mode on or off.
0 DISPLAY (p. 12)
Switch the time display.
A ENTER (p. 15)
Confirm the track number when this unit is in program
input mode.
INTRODUCTION
B CLEAR (p. 16)
Clear programmed track.
C REPEAT (p. 13)
Repeat playback of a single track or all tracks.
D RANDOM (p. 13)
Set random-sequence play.
E A/B (p. 14)
Set repeat A-B.
F (Pause) (p. 10)
Pause playback.
G (Play) (p. 9)
Start playback.
H (Stop) (p. 10)
Stop playback.
English
5 En
CONTROLS AND FUNCTIONS
Installing batteries in the remote control
1 Press the part and slide the battery
compartment cover off.
2 Insert two supplied batteries (AA, R6, UM-3)
according to the polarity markings (+ and –)
on the inside of the battery compartment.
3 Slide the cover back until it snaps into place.
■ Notes on batteries
• Change both batteries when the operation range of the
remote control decreases.
• Use AA, R6, UM-3 batteries.
• Make sure that the polarities are correct. See the
illustration inside the battery compartment.
• Remove the batteries if the remote control is not to be
used for an extended period of time.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline
and manganese batteries) together. Read the packaging
carefully as these different types of batteries may have
the same shape and color.
• If the batteries have leaked, dispose of them
immediately. Avoid touching the leaked material or
letting it come into contact with clothing, etc. Clean the
battery compartment thoroughly before installing new
batteries.
• Do not throw away batteries with general house waste;
dispose of them correctly in accordance with your local
regulations.
Using the remote control
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the front panel of this unit during
operation.
Within 6 m
(20 ft)
■ Handling the remote control
• The area between the remote control and this unit must
be clear of large obstacles.
• Do not spill water or other liquids on the remote
control.
• Do not drop the remote control.
• Do not leave or store the remote control in the
following types of conditions:
– high humidity, such as near a bath
– high temperature, such as near a heater or a stove
– extremely low temperatures
– dusty places
• Do not expose the remote control sensor to strong
lighting, in particular, an inverter type fluorescent
lamp; otherwise, the remote control may not work
properly. If necessary, position the unit away from
direct lighting.
6 En
PREPARATION
CONNECTIONS
Connecting your amplifier
CAUTION
• Before making any connection, switch OFF the power to the unit, the amplifier and any other component.
• Connections should be made to the correct input terminals of the amplifier or another component.
• If the placement of this unit causes noise to another equipment, such as a tuner, move them further away from each
other.
PREPARATION
RCA stereo
cable
(supplied)
• The digital output is turned off when this unit is in PURE DIRECT mode.
To connect this unit to your amplifier, choose one of the ways listed below.
When the ANALOG OUT terminals of this
unit are used ( )
Connect these terminals to the CD (or AUX) terminals of
the amplifier by using a supplied RCA stereo cable. For
details concerning these connections, refer to the
operation instructions of the amplifier being used.
• Be sure that the left (L) and right (R) of these terminals
are connected to the corresponding (left and right)
terminals of the amplifier or other component.
Coaxial cableOptical cable
When the DIGITAL OUT (COAXIAL) terminal
of this unit is used ( )
Connect this terminal to the digital input terminal of an
amplifier with a commercially available coaxial cable.
When the DIGITAL OUT (OPTICAL) terminal
of this unit is used ( )
Connect this terminal to the optical input terminal of an
amplifier with a commercially available optical cable.
• Use a reliable optical cable.
Amplifier
English
7 En
CONNECTIONS
Connecting the supplied power cable
Asia and General models
only
Europe and U.K. models
To the wall outlet with the
supplied power cable
■ VOLTAGE SELECTOR
(Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
the supplied power cable into the wall outlet.
Improper setting of the VOLTAGE SELECTOR may
cause damage to this unit and create a potential fire
hazard.
Rotate the VOLTAGE SELECTOR clockwise or
counterclockwise to the correct position using a straight
slot screwdriver.
Voltages are as follows:
.............................. AC 110/120/220/230-240 V, 50/60 Hz
■ Connecting this unit to the wall outlet
Plug the supplied power cable into the AC IN on the rear
panel of this unit and then plug the power cable into the
wall outlet after all other connections are complete.
Connecting USB devices
This unit has a USB port and can access MP3 or WMA
files saved on your USB device. Connect your USB
device to the USB port on the front panel of this unit.
CAUTION
Do not disconnect your USB device while playing back
from the USB device, or when the USB indicator blinks.
■ Supported USB devices
This unit supports USB mass storage class devices (e.g.,
flash memories, card readers or portable audio players)
that use FAT16 or FAT32 format.
Notes
• Some devices may not work properly even if they meet the
requirements.
• Do not connect devices other than USB mass storage class
devices: USB chargers, USB hubs, PCs, external HDD, etc.
• When you insert two or more memory cards at the same time
into a card reader connected to the USB port on this unit, only
one of the memory cards is recognized.
• Yamaha and suppliers accepts no liability for the loss of data
saved on the USB devices connected to this unit. As a
precaution, it is recommended that the files are made backup
copies.
• Playability of and power supply to all kind of USB devices are
not guaranteed.
8 En
OPERATION
This manual describes how to operate this unit by using the remote control.
To operate this unit from the front panel, use the corresponding buttons on the front panel.
The , and icons indicate music data formats that can be
Audio CD Data Disc USB
used in the operation.
BASIC OPERATION
Notes
• When you load a disc, set the disc on the inside of the disc
guides (4 marks on the disc tray).
• The disc may not be read correctly, if it is set incorrectly. In this
case, open the disc tray and set the disc again.
2 Press OPEN/CLOSE to close the disc tray.
1 Press POWER to turn on the power.
y
You can also close the disc tray by pressing h, a numeric button,
or by pressing the front edge of the disc tray gently. If the tray is
closed in one of these ways, playback starts automatically.
OPERATION
2 Press CD/USB to switch between disc mode
and USB mode.
When USB mode is selected, the USB indicator lights
up, and when disc mode is selected, the USB
indicator lights off.
y
This setting is retained even if you turn off this unit.
Starting playback
■ Playing back discs
Audio CD Data Disc
1 Press OPEN/CLOSE to open the disc tray,
and load a disc.
Label side up.
3 Press h to start playback.
For an Audio CD, playback starts from the first track,
and for a Data Disc, in alphanumeric order by
filename.
Display information in step 2
Audio CD
Total number of tracks Total recorded time of a disc
Data Disc
Total number of files
Disc tray
English
9 En
BASIC OPERATION
■ Playing back USB devices
USB
Turning off the power
Connect your USB device to the USB port on the
front panel. (For details, refer to page 8.)
When USB mode is selected (USB indicator lights up),
first filename is displayed in the front panel display (refer
to page 12), and playback starts automatically in order by
date and time of creation if playable files are in the USB
device.
To disconnect USB devices
Press to stop playback, and then disconnect the USB
device.
Note
Do not disconnect your USB device while playing back from the
USB device, or when the USB indicator blinks.
Pausing playback
USBAudio CD Data Disc
Press e.
To resume playback, press e again (or press h).
Press POWER again.
If you turn off the power when disc mode is selected, the
next time you turn the power on, playback starts
automatically of the disc on the tray. If you turn off the
power when USB mode is selected, playback will start
automatically of the USB device connected.
Playing back a desired track
Audio CD
Select a desired track by using the numeric
buttons.
Example: To select track number 12
Press “1”, and then press “2”.
+
Following information is displayed.
The selected track number
Playback starts in 2 seconds.
Note
This operation is not available for Data Disc and USB.
y
You can also select and playback a desired track during playback.
Stopping playback
USBAudio CD Data Disc
Press s.
If you press h again, playback starts from the first track.
10 En
To improve audio quality (PURE DIRECT mode)
USBAudio CD Data Disc
Press PURE DIRECT.
This unit is set to PURE DIRECT mode.
• The PURE DIRECT indicator lights up.
• The digital output is turned off.
• The front panel display is turned off and only the minimum
required indicators and messages are displayed during
playback.
Note
Connect using the ANALOG OUT terminals when you use
PURE DIRECT mode (refer to page 7).
y
• Press PURE DIRECT again to turn off PURE DIRECT mode.
• This setting is retained even if you turn off this unit.
BASIC OPERATION
Advancing or reversing playback rapidly
Skipping to the beginning of a desired track
USBAudio CD Data Disc
To play back from the beginning of the next
track, press once.
To play back from the beginning of the current
track, press once.
To play back from the beginning of the previous
track, press twice.
y
• These operations can also be performed for Data Disc/USB.
• These operations can also be performed when the unit is
paused.
• These operations can also be performed using b/w and
f/a on the front panel.
USBAudio CD Data Disc
To advance rapidly, press once during
playback.
To reverse rapidly, press once during
playback.
To resume playback, press at the desired
point.
y
• These operations can also be performed for Data Disc/USB.
• The sound can be heard (although slightly garbled) during these
operation in either direction. This is convenient for locating a
precise position within a track, or for reviewing the contents
quickly. Sound may not be heard depending on the MP3/WMA
file.
• Each time you press or , the search speed increases
by 2 levels.
• These operations can also be performed pressing and holding
b/w or f/a on the front panel for more than 2
seconds.
OPERATION
11 En
English
BASIC OPERATION
Changing front panel display
■ When playing back an Audio CD
Audio CD
You can select the following front panel displays (1 - 3) by pressing DISPLAY.
1 Elapsed time of the current track (Default)
2 Remaining time of the current track
3 Remaining time of the disc
■ When playing back a Data Disc or USB device
USBData Disc
You can temporarily display the filename by pressing DISPLAY.
These front panel display examples are for an MP3 file.
1 Elapsed time of the current track
Returns to the normal display after displaying
2 Filename*
* 28 characters maximum
Note
This unit can only show alphanumeric characters.
a filename.
Changing the brightness of the front panel display
Press DIMMER to change the brightness level for
the front panel display.
Each time you press DIMMER, the brightness level
changes in the following order:
Max (brightest) J Level1 (default) J Level2 J Level3
(darkest) J Max
Notes
• Brightness is slightly decreased during playback, except when
the level is set to maximum.
• Brightness may temporarily be decreased for some operations,
except when the level is set to maximum.
• This setting is retained even if you turn off this unit.
12 En
RANDOM-SEQUENCE PLAY
USBAudio CD Data Disc
You can play back the tracks in random sequence.
To perform random-sequence play
Press , and then, RANDOM.
+
To cancel random-sequence play
Press .
REPEAT PLAY
Repeating a selected item
Note
These operations can also be performed for Data Disc/USB.
OPERATION
USBAudio CD Data Disc
You can play back a single track or all tracks repeatedly
by pressing REPEAT during playback. The repeat
playback mode changes each time you press REPEAT.
(Single repeat)
(Full repeat)
(off)
S (Single repeat)
A single track is played back repeatedly.
ALL (Full repeat)
All tracks (the entire disc) are played back repeatedly.
Note
These operations can also be performed for Data Disc/USB.
y
Repeat play also works for program play and random-sequence
play.
English
13 En
REPEAT PLAY
Repeat A-B
Audio CD
You can repeat a specified section of a track by pressing
A/B during playback to set two points (start and end
points).
1 Press A/B to select the start point of repeat
play.
“A-” lights up.
2 Press A/B to select the end point of repeat
play.
“A-B” lights up.
The selected section is played back repeatedly.
To cancel repeat A-B
Press A/B again to make “A-B” disappear from the front
panel display.
Notes
• You cannot set repeat A-B from one track to another track.
• This operation is not available for Data Disc and USB.
• If you stop playback by pressing , repeat A-B is canceled.
• You cannot use repeat A-B when this unit is in PURE DIRECT
mode.
14 En
PROGRAM PLAY
Audio CD
You can customize the playback order of up to 50 tracks
stored on an Audio CD. This operation is not available for
Data Disc and USB.
1 Press s to stop playback.
Following information is displayed.
When you press “6”:
The selected track number
When you press ENTER:
Total number of tracks
currently programmed
Total time of the tracks
currently programmed
Repeat this operation to program more tracks.
You can select the same track again.
Note
Pressing PROGRAM in program input mode exits to normal
playback mode, though programmed tracks are stored.
4 Press h to start program play.
OPERATION
2 Press PROGRAM.
• In this mode, the front panel
display shows as normally, even
when this unit is in PURE
DIRECT mode.
This unit is set to program input mode.
3 Program a desired track by pressing the
corresponding numeric button and ENTER.
+
Following information is displayed.
Current track
Elapsed time of the
current track
English
15 En
PROGRAM PLAY
Stopping program playback
Press s.
To restart program play, press h after pressing
PROGRAM.
Playback starts from the first programmed track number.
Clearing programmed track
There are several methods, as described below.
■ Clearing the last programmed track
Press CLEAR during program input mode.
Following information is displayed.
Total number of the
tracks currently
programmed
The last programmed track is cleared.
Total time of the
tracks currently
programmed
■ Clearing all programmed tracks
Press CLEAR after exiting program input
mode.
Following information is displayed.
All programmed tracks are cleared.
The display is turned off after 2 seconds.
Note
Switching to USB mode, opening the disc tray or switching off
the POWER clears all programmed tracks.
16 En
ADDITIONAL INFORMATION
NOTES ABOUT DISCS/MP3, WMA FILES
■ Discs playable with this unit
Audio CD Data Disc
This player is designed for playing back compact discs
bearing the marks shown below. Never attempt to load
any other type of disc into the unit. The unit can also play
back 8-cm (3-inch) compact discs.
....
Compact discs (digital audio)
The most popular discs for commercially
available audio CDs.
....
CD-R,CD-RW digital audio discs
Music CDs made by copying onto a CD-R
or CD-RW (including MP3 or WMA
format files).
Notes
• Be sure to use a CD-R or CD-RW disc made
by a reliable manufacture.
• Be sure to use a CD-R or CD-RW disc which
has at least one of the following phrases on
the disc or disc case.
FOR CONSUMER
FOR CONSUMER USE
FOR MUSIC USE ONLY
• Be sure to use a finalized CD-R or CD-RW
disc.
....
CD-TEXT discs
The discs recorded with text data such as
album titles, track titles and artist names.
Though these discs can be played back
with ordinary CD players, the text data is
not displayed.
MP3
MP3 is a standard technology and format for compressing
an audio sequence into a small-sized file. However, the
original level of sound quality is preserved during
playback.
The playable formats are:
• MPEG-1 Audio Layer-3
Bitrate*: 32-320 kbps
Sampling frequency: 44.1/48/32 kHz
• MPEG-2 Audio Layer-3, 2
Bitrate*: 8-160 kbps
Sampling frequency: 24/22.05/16 kHz
• MPEG-2.5 Audio Layer-2
Bitrate*: 8-160 kbps
Sampling frequency: 12/11.025/8 kHz
* Variable bitrate is supported.
WMA
“WMA (Windows Media Audio)” is a Microsoft file
format for encoding digital audio files similar to MP3
though can compress files at a higher rate than MP3.
The playable formats are:
•Version 8
• Version 9 (Standard and variable bitrates are
supported. Professional and Lossless are not
supported.)
• High Profile
Bitrate*: 32-320 kbps
Sampling frequency: 48/44.1/32 kHz
• Mid Profile
Bitrate: 16-32 kbps
Sampling frequency: 22.05/16 kHz
* Both constant and variable bitrates are supported.
INFORMATION
ADDITIONAL
Note
This compact disc player may not be able to play back some
CD-RW discs or discs on which recording was not made
correctly.
To prevent a malfunction of this unit:
• Do not use any nonstandard
shaped disc (heart, etc.) available
on the market because it might
damage the unit.
• Do not use a disc with tape, stickers, or paste on it. If
you use such a disc, the disc may get stuck in the
unit, or damage to the unit may result.
■ About MP3 and WMA files
Data Disc USB
You can play back MP3 and WMA files recorded on a
CD-R/CD-RW and those stored on a USB device.
Notes
• Playback for Data Disc starts in alphanumeric order.
• Playback for USB starts in order by date and time of creation.
• Copyright-protected WMA (DRM) files cannot be played back
by this unit.
• The disc must be ISO9660 compatible.
• The maximum file and folder numbers are as follows.
Data Disc USB
Maximum file number
Maximum folder number
Maximum file number per
folder
512 999
255 255
511 255
(continued on the next page)
17 En
English
NOTES ABOUT DISCS/MP3, WMA FILES
■ Notes about handling compact discs
• Always handle a disc with care so that its surface is not
scratched.
• Compact discs are not subjected to wear during
playback, but damage to the disc surface when the disc
is being handled can adversely affect the disc playback.
• Be sure to use a felt-tip pen or similar writing tool
when writing on the label side of the disc. Do not use a
ballpoint pen, pencil, or other hard-tipped writing tool,
as these may damage the disc and may adversely affect
the disc playback.
• Do not warp discs.
• When a disc is not being used, remove it from the unit
and store in an appropriate case.
• When removing or storing a disc, be careful not to
scratch the playing surface.
• Compact discs are not affected by small particles of
dust or fingerprints on their playing surface, but even
so they should be kept clean. Wipe by using a clean,
dry cloth.
Do not wipe with a circular motion; wipe straight
outward from the center.
To play back an 8-cm (3-inch) CD
Place it in the inner recessed area of the disc tray. Do not
put a normal (12-cm) CD on top of an 8-cm (3-inch) CD.
• Do not try to clean the disc’s surface by using any type
of disc cleaner, record spray, anti-static spray or liquid,
or any other chemical-based liquid because such
substances might irreparably damage the disc’s
surface.
• Do not expose discs to direct sunlight, high
temperature or high humidity for a long period of time,
as these might warp or otherwise damage the disc.
No!
18 En
TROUBLESHOOTING
If the unit fails to operate normally, check the following points to determine whether the problem can be corrected by the
simple measures suggested. If it cannot be corrected, or if the problem is not listed in the Problems column, disconnect
the power cable and contact your authorized Yamaha dealer or service center for help.
Problems Possible Causes Solutions
This unit fails to turn
on.
The disc tray does
not close completely.
Disc playback does
not start.
USB playback does
not start.
Playback is delayed,
or begins at the
wrong place.
No sound. Improper output cable connections. Connect the cables properly. If the problem
Sound of a
component
connected to the
DIGITAL OUT jacks
is not played.
Sound “skips”. This unit is being subjected to vibrations or
Sound “hums”. Improper cable connections. Securely connect the audio cables. If the
Noise from a nearby
tuner.
Noise from inside of
the disc tray.
The power cable is not connected to the AC IN
inlet on the rear panel or not plugged in the wall
outlet.
A foreign object is obstructing the tray. Carefully check the disc tray and remove the
The disc is damaged. Check the disc carefully; replace it if necessary. —
There is moisture on the laser pickup. Wait 20 to 30 minutes after switching on the
The disc is loaded upside down. Reload the disc with the label side up. 9
The disc is dirty. Clean the disc. 18
The format of the MP3 or WMA file is not
compatible with this unit.
The CD-RW (ReWritable) disc is not recorded
correctly.
The disc is a non-standard disc not playable with
this unit.
This unit is in USB mode. Switch to disc mode by pressing CD/USB.5, 9
Improper USB device connections. Connect the USB device again. 8
The format of the MP3 or WMA file is not
compatible with this unit.
This unit is in disc mode. Switch to USB mode by pressing CD/USB.5, 9
The disc may be scratched or damaged. Check the disc carefully; replace it if necessary.
Improper amplifier operation. Set the amplifier controls to the correct input
PURE DIRECT is turned on. Turn PURE DIRECT off. Or make an analog
impacts.
The disc is dirty. Clean the disc. 18
The tuner is too close to this unit. Move the tuner and this unit farther apart.
The disc may be warped. Replace the disc.
Connect the power cable firmly.
foreign object.
unit ON before trying to play back a disc.
Replace the disc with a correctly recorded disc
playable with this unit.
Replace the disc with a correctly recorded disc
playable with this unit.
Replace the disc with a correctly recorded disc
playable with this unit.
Replace the file with a correctly recorded file
playable with this unit.
persists, the cables may be defective.
selection.
connection.
Relocate this unit.
problem persists, the cables may be defective.
Refer to
page
8
—
—
17
17
17
17
18
7
—
10
—
7
—
—
INFORMATION
English
ADDITIONAL
19 En
Loading...