Yamaha 001PO-03C0, IPA8200 User Manual

1

EnglishDeutschFrançaisEspañolItaliano

IPA8200 Owner’s Manual

EN

DE

FR

ES

IT

RU

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The above warning is located on the top of the unit.

IMPORTANT SAFETY INSTRUCTIONS

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol
within an equilateral triangle is intended to alert
the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the product.

1 Read these instructions.
2Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table specified
by the manufacturer, or sold with
the apparatus. When a cart is
used, use caution when moving
the cart/apparatus combination to
avoid injury from tip-over.

13 Unplug this apparatus during

lightning storms or when unused for long periods of
time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.

(UL60065_03)

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT:

supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authori­zation to use this product in the USA.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (oscillator)

In Finland: Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.
In Norway: Apparatet må tilkoples jordet stikkontakt.
In Sweden: Apparaten skall anslutas till jordat uttag.

IPA8200 Owner’s Manual

2

When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s

(class1_hokuo)

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

Power supply/Power cord

• Only use the voltage specified as correct for the device. The required voltage is
printed on the name plate of the device.

• Use only the included power cord.
If you intend to use the device in an area other than in the one you purchased,
the included power cord may not be compatible. Please check with your Yamaha
dealer.

• Do not place the power cord near heat sources such as heaters or radiators, and
do not excessively bend or otherwise damage the cord, place heavy objects on
it, or place it in a position where anyone could walk on, trip over, or roll anything
over it.

• Be sure to connect to an appropriate outlet with a protective grounding
connection. Improper grounding can result in electrical shock.

Do not open

• Do not open the device or attempt to disassemble the internal parts or modify
them in any way. The device contains no user-serviceable parts. If it should
appear to be malfunctioning, discontinue use immediately and have it inspected
by qualified Yamaha service personnel.

CAUTION

Water warning

• Do not expose the device to rain, use it near water or in damp or wet conditions,
or place containers on it containing liquids which might spill into any openings.
If any liquid such as water seeps into the device, turn off the power immediately
and unplug the power cord from the AC outlet. Then have the device inspected
by qualified Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

If you notice any abnormality

• If the power cord or plug becomes frayed or damaged, or if there is a sudden
loss of sound during use of the device, or if any unusual smells or smoke
should appear to be caused by it, immediately turn off the power switch,
disconnect the electric plug from the outlet, and have the device inspected by
qualified Yamaha service personnel.

• If this device should be dropped or damaged, immediately turn off the power
switch, disconnect the electric plug from the outlet, and have the device
inspected by qualified Yamaha service personnel.

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the device or other property. These precautions include, but are not limited to, the following:

Power supply/Power cord

• Remove the electric plug from the outlet when the device is not to be used for
extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always hold the
plug itself and not the cord. Pulling by the cord can damage it.

Location

• Before moving the device, remove all connected cables.

• When setting up the device, make sure that the AC outlet you are using is easily
accessible. If some trouble or malfunction occurs, immediately turn off the
power switch and disconnect the plug from the outlet. Even when the power
switch is turned off, electricity is still flowing to the product at the minimum
level. When you are not using the product for a long time, make sure to unplug
the power cord from the wall AC outlet.

• If the device is mounted in an EIA standard rack, carefully read the section
“Precautions when rack-mounting the unit” on page 5. Inadequate ventilation
can result in overheating, possibly causing damage to the device(s),
malfunction, or even fire.

• Do not use the device in a confined, poorly-ventilated location. Make sure that
there is adequate space between the device and surrounding walls or other
devices: at least 5cm at the sides, 10cm behind and 10cm above. Inadequate
ventilation can result in overheating, possibly causing damage to the device(s),
or even fire.

• Do not expose the device to excessive dust or vibrations, or extreme cold or heat
(such as in direct sunlight, near a heater, or in a car during the day) to prevent
the possibility of panel disfiguration or damage to the internal components.

• Do not place the device in an unstable position where it might accidentally fall
over.

• Do not block the vents. This device has ventilation holes at the front and rear to
prevent the internal temperature from becoming too high. In particular, do not
place the device on its side or upside down. Inadequate ventilation can result in
overheating, possibly causing damage to the device(s), or even fire.

• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile
phone, or other electric devices. Doing so may result in noise, both in the device
itself and in the TV or radio next to it.

• Do not place the device in a location where it may come into contact with
corrosive gases or salt air. Doing so may result in malfunction.

(5)-6

1/2

IPA8200 Owner’s Manual

3

Connections

• Before connecting the device to other devices, turn off the power for all devices.
Before turning the power on or off for all devices, set all volume levels to
minimum.

•Turn off the power before connecting speakers, and use only the speaker cables
for connecting speakers to the speaker jacks.
Failure to do so can result in fire or electrical shock.

Handling caution

• When turning on the AC power in your audio system, always turn on the device
LAST, to avoid speaker damage. When turning the power off, the device should
be turned off FIRST for the same reason.

• Condensation can occur in the device due to rapid, drastic changes in ambient
temperature – when the device is moved from one location to another, or
airconditioning is turned on or off, for example. Using the device while
condensation is present can cause damage. If there is reason to believe that

condensation might have occurred, leave the device for several hours without
turning on the power until the condensation has completely dried out.

• Do not insert your fingers or hands in any gaps or openings on the device
(vents).

•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any
gaps or openings on the device (vents) If this happens, turn off the power
immediately and unplug the power cord from the AC outlet. Then have the
device inspected by qualified Yamaha service personnel.

• Do not use speakers for a long period of time at a high or uncomfortable volume
level, since this can cause permanent hearing loss. If you experience any
hearing loss or ringing in the ears, consult a physician.

• Do not rest your weight on the device or place heavy objects on it, and avoid use
excessive force on the buttons, switches or connectors.

• Do not use this device for any purpose other than driving loudspeakers.

Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualified Yamaha service
personnel about replacing defective components.

European models
Purchaser/User Information specified in EN55103-1 and EN55103-2.
Inrush Current: 26A
Conforms to Environments: E1, E2, E3 and E4

* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications

at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in accordance with the following code:

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in
your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the
safety earth symbol or colored GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

• This applies only to products distributed by Yamaha Music U.K. Ltd. (3 wires)

GREEN-AND-YELLOW : EARTH
BLUE : NEUTRAL
BROWN : LIVE

IPA8200 Owner’s Manual

4

(5)-6

2/2

Thank you for purchasing the Yamaha IPA8200 power amplifier.
In order to take full advantage of the IPA8200’s functionality and to ensure trou­ble-free operation, please read this owner’s manual carefully before use.
After you have read the manual, keep it in a safe place for reference when needed.

Features

Space-saving high-efficiency multi-channel 200W@4 Ω x 8 power amplifier

■

■

■

■

■

Introduction

Switchable between STEREO/PARALLEL/BRIDGE modes as needed for
your application

Euroblock input jacks and barrier strip output jacks for easy installation

High-pass filter with switchable cutoff frequency (20 Hz / 55 Hz)

Input sensitivity / gain select switch switchable between three positions
(+4 dBu, 26 dB, 32 dB)

Precautions when rack-mounting the unit

Operation of this device is guaranteed for an environmental temperature range of 0 – 40°C. If you are mounting
only this device in an EIA standard rack, you may mount multiple units without leaving a space between them. If
you are mounting this device along with other types of device in an EIA standard rack, the ambient temperature
inside the rack may rise due to heat produced from the other devices, preventing this device from performing as
designed. To ensure that heat does not build up inside this device, you must observe the following conditions when
mounting it in a rack.

• If you mount this device in a rack together with heat-generating devices such as power amps made by other com­panies, you must leave 1U or more space between this device and other devices. You should also install a ventila­tion panel in this space or leave it open to ensure adequate ventilation.

• Leave the back of the rack open, and allow 10 cm or more distance between the rack and the wall or ceiling to
ensure adequate ventilation. If you are unable to leave the back of the rack open, you must install a commercially
available fan kit or other forced air circulating system to the rack. If you have installed a fan kit, there may be
cases in which closing the back of the rack will provide better cooling. For details, refer to the instructions that
came with the rack system or fan kit.

IPA8200 Owner’s Manual

5

Contents

Introduction............................................................................................................. 5

Features ..............................................................................................................5

Precautions when rack-mounting the unit ...........................................................5

Controls and Functions .........................................................................................7

Front Panel.......................................................................................................... 7

Rear Panel........................................................................................................... 8

Mode settings ......................................................................................................... 9

STEREO mode....................................................................................................9

PARALLEL mode ................................................................................................9

BRIDGE mode.....................................................................................................9

Connections.......................................................................................................... 10

Input jack connections (Euroblock).................................................................... 10

Speaker connections (barrier strip) ...................................................................10

Troubleshooting ...................................................................................................11

Specifications .......................................................................................................57

General Specifications....................................................................................... 57

Block Diagram ...................................................................................................58

Dimensions........................................................................................................58

Current Draw .....................................................................................................59

Accessories (Please make sure the following items are

included in the package.)

•IPA8200 Owner’s Manual (this document)

•Power cable (2.5 m) x 1

• Security cover x 1

• Allen wrench x 1

• Security cover attachment screws x 2

• Euroblock plug (3P) x 8

IPA8200 Owner’s Manual

6

q

w

e

Ω

r

Controls and Functions

Front Panel

Security cover

Ω

Ω

t

∞

y

u

i

o

!0

!1

POWER switch and indicator

Turns power to the unit on or off. The indicator lights green
when the power is on.

PROTECT indicator

When the protection system is active, the indicator lights
red. When this is lit, the amplifier or power supply is auto­matically shut down, and no sound will be output from the
speakers.

CLIP indicator

This indicator will light red when the output power exceeds
100 W for an 8
lit, the limiter will automatically operate.

SIGNAL indicator

This indicator will light green when the output level exceeds
2 Vrms. (This will light at 0.5 W or greater for an 8
1W or greater for a 4

Attenuator

These are detented knobs that attenuate the input signal of
each channel (A–H) over 41 steps in a range of 0 dB – –
dB.

NOTE

•To operate these knobs, use a slotted screwdriver with
a blade no wider than 5.5 mm.

load or 200 W for a 4 Ω load. When this is

load,

load.)

MUTE indicator

This will light red when mute is activated.

MUTE switch

This turns muting on/off for each channel. Use a thin rod to
turn muting on/off.

PARALLEL indicator

This will light orange when the rear panel MODE switch is
set to PARALLEL.

BRIDGE indicator

This will light orange when the rear panel MODE switch is
set to BRIDGE.

Screw holes for security cover

If desired, you can use these two screw holes for attaching
the included security cover to prevent the attenuator setting
from being changed. Use the included Allen wrench and
screws to attach the cover.

Air intakes

The amplifier uses forced-air cooling. The variable speed
cooling fan draws air in from the front and exhausts it
through the rear. The cooling fan operates at low speed when
the heat sink temperature is below 65 °C (149 °F), or at high
speed when the temperature exceeds 65 °C (140 °F). Please
be sure that you do not block the air intakes or exhaust vents.

IPA8200 Owner’s Manual

7

Controls and Functions

Rear Panel

q

w

e

r

t

y

u

q

INPUT connectors

These are balanced input connectors. The included Eurob­lock connectors can be used to make connections here.

SPEAKERS connectors

These are barrier strip type speaker output connectors.

NOTE

• If using BRIDGE mode, connect the speakers to the “+”
pin of channels A/C/E/G and the “–” pin of channels B/
D/F/H.

• Do not connect the pin marked NC located in the center
of the bottom row of the barrier strip connectors.

rwe

t

uy

GAIN switch

This switches the input sensitivity / gain for all channels
together.

• +4 dBu: Sets the input sensitivity to +4 dBu.

• 26 dB: Sets the gain to 26 dB.

• 32 dB: Sets the gain to 32 dB.

HPF switch

Turns the high pass filter (20 Hz or 55 Hz) on/off. If this is
set to 20 Hz or 55 Hz, the frequency components below that
frequency will be cut by a 12 dB/oct. filter.

MODE switches

These specify the amplifier’s operation mode for each two
channels.

• STEREO mode

Each channel (A–H) will operate independently.

• BRIDGE mode

The amplifiers will be bridged for pairs of adjacent chan­nels (A-B, C-D, E-F, G-H), obtaining a high-power out­put.

•PARALLEL mode

The input signals will be input to the adjacent channels
(A-B, C-D, E-F, G-H) as well.

Ground screw

Hum and interference may be reduced in some cases by con­necting the screw to an ground or to the chassis of the mixer,
preamp, or other device in your system.

AC inlet

Connect this to the socket end of the included AC power
cable . Connect the plug end of the AC power cable to an AC
outlet of the correct voltage.

• If this device is to be rack mounted and transported
frequently, be sure to support the rear end of the unit

CAUTION

with mounting hardware that matches the size of the
rack used.

IPA8200 Owner’s Manual

8

Mode settings

NOTE

Speakers can be connected to the IPA8200 using the following three mode settings. The total load impedance of
the speakers that can be connected will depend on the mode setting. Do not use a setup that has a lower impedance
than the minimum values shown below.

STEREO mode

If the rear panel MODE switch is set to STEREO, each chan­nel will operate independently. You can use the front panel
attenuators to adjust the attenuation for each channel inde­pendently.

Source:

Channel B

NOTE

•Total speaker impedance must be 4–8 Ω .

Source:

Channel A

Total speaker
impedance: 4–8Ω

BRIDGE mode

If the rear panel MODE switch is set to BRIDGE, the ampli­fiers will be bridged between adjacent pairs of channels (A­B, C-D, E-F, G-H), and the IPA8200 will operate as a high­power amplifier. Either of adjacent two channels can be used
as an input connector. Use the front panel channel A/C/E/G
attenuators to adjust the attenuation.

• If using BRIDGE mode, connect the speakers to the “+”
pin of channels A/C/E/G and the “–” pin of channels B/
D/F/H.

•Total speaker impedance must be 8–16 Ω.

PARALLEL mode

If the rear panel MODE switch is set to PARALLEL, the
input signals will be input to the adjacent channels (A-B, C­D, E-F, G-H) as well. Either of adjacent two channels can be
used as an input connector. You can use the front panel atten­uators to adjust the attenuation for each channel indepen­dently.

Total speaker

Source:

Channel A

NOTE

•Total speaker impedance must be 4–8 Ω .

Source:

Channel A

impedance: 4–8Ω

Source:

Channel A

Total speaker
impedance: 8–16Ω

IPA8200 Owner’s Manual

9

Connections

NOTE

Input jack connections (Euroblock)

Please be sure to use the supplied Euroblock connectors.
If you lose them, contact your nearest Yamaha dealer.

● Cable preparation

•To prepare the cable for attachment to a Euroblock con­nector, strip the wire as shown in the illustration, and use
stranded wire to make connections. With a Euroblock
connection, the stranded wire may be prone to breakage
because of metal fatigue due to the weight of the cable or
due to vibration. When rack-mounting your equipment,
use a lacing bar when possible to bundle and fasten the
cables.

approx.

7 mm

• If cables will be frequently connected and disconnected,
as in the case of a portable installation, we recommend
that you use ferrules with insulation sleeves. Use a ferrule
whose conductor portion has an external diameter of 1.6
mm or less, and a length of approximately 7 mm (such as
the AI0, 5-6WH made by the Phoenix Contact corpora­tion).

1.6 mm
or less

approx.

7 mm

Speaker connections (barrier strip)

If using a spade lug

From below, insert the spade lug all the way, and tighten the
screw.

If using a bare conductor

Wrap the conductor around the barrier strip terminal as
shown below, and tighten the screw. Be sure that the bare
wire does not touch the chassis.

• If you use stranded wire, do not tin (plate
with solder) the exposed end.

CAUTION

1. If the wire insertion ports are closed, turn the screws on

top of the connector counterclockwise to open the
ports.

2. Insert the wires into the appropriate ports, following

the indication of the pole on the input terminal, and
turn the screws on top of the connector clockwise to
fasten the wires.

3. Connect the Euroblock connector to the IPA8200’s

input jack.

Use a slotted screwdriver
to fix the wires.

Wires

15mm*

Wire should
not touch

* Actual size

• Do not connect the pin marked NC located in the center
of the bottom row of the barrier strip connectors.

• If using BRIDGE mode, connect the speakers to the “+”
pin of channels A/C/E/G and the “–” pin of channels B/
D/F/H.

Speaker
cable

the chassis.

IPA8200 Owner’s Manual

10

Euroblock connector

G

–

+

Troubleshooting

Indicator(s) Possible cause Remedy Protection circuit

CLIP indicator is
lit.

PROTECT indi­cator is lit.

Output exceeds 100 W
(8Ω) or 200 W (4Ω).

Speaker output connec­tor is shorted.

The power amp section’s
heat sink temperature has
exceeded 95°C or the
power supply section’s
heat sink temperature has
exceeded 85°C.

A DC offset voltage is
being output to the
speaker output connector.

Lower the input level. Limiter circuit will operate

to protect the power amp
and power supply.

Check whether the speaker output con­nector or speaker cable could be shorted,
and then power-cycle the IPA8200.
If the PROTECT indicator is still lit, con­tact your Yamaha dealer.

Check whether there might be blockage
at the air intake or a ventilation problem
inside the rack, and verify that the load
impedance of the connected speakers is
not below the rated value (4Ω or 8Ω/
BRIDGE).
Then wait until the unit’s temperature has
dropped, and power-cycle the unit.
If the PROTECT indicator is still lit, con­tact your Yamaha dealer.

Consult your Yamaha dealer. The protection circuit will

The protection circuit will
operate to project the
power amp and power
supply.

The protection circuit will
operate to protect the
power amp.

operate to protect the
speakers.

IPA8200 Owner’s Manual

11

Specifications

General Specifications

Output Power 4Ω per channel 200W x 8

8Ω per channel 100W x 8

1kHz, THD+N=1% 8Ω / BRIDGE 400W x 4

4Ω per channel 180W x 8
8Ω per channel 90W x 8

20Hz-20kHz, THD+N=1%

1kHz, 20ms Burst
Maximum Input Level +24dBu
Input Impedance 20kΩ(balanced), 10kΩ(unbalanced)
Input Sensitivity (dBu) Switch Position +4dBu 26dB 32dB

8Ω, Att. max Input sensitivity +4dBu +5.2dBu –0.8dBu
Voltage Gain Switch Position +4dBu 26dB 32dB

Att. Max Voltage Gain 27.2dB 26dB 32dB
S/N Ratio A-weighted ≥100dB
THD+N 1kHz, half power, 4Ω≤0.5%
Frequency Response 1W, 8Ω 20Hz-20kHz, +0dB, –1.5dB
Channel Separation 1kHz, half power, 8Ω

Controls Front Panel POWER switch (rocker)

Connectors Input Euroblock (balanced)/ch

Indicators POWER x 1 (Green), PROTECT x 8 (Red),

Load Protection POWER switch on/off Output mute

Amplifier Protection Thermal Output mute (heatsink temp ≥95˚C)

Power Supply Protection Thermal Power supply shutdown (heatsink temp ≥85˚C)
Limiter Circuit Clip limiting Limiting level ≥100W@8Ω or 200W@4Ω
Cooling High/Low two speed fan x 2
AC Power Requirement U.S./Canada: 120V, 60Hz

Power Consumption 400W
Dimensions (W x H x D) 480 x 88 x 406.5mm (18-7/8 x 3-7/16 x 16 inch)

Weight 10.5kg (23.2 lbs)
Included Accessories AC power cord (2.5m) x 1, Security cover x 1,

• Half power = 3dB below rated power

• 0dBu = 0.775Vrms

8Ω / BRIDGE 360W x 4
4Ω per channel 200W x 8
8Ω per channel 100W x 8
8Ω / BRIDGE 400W x 4

Att. max, input 600Ω shunt

MUTE switch (push ON/push OFF) x 8

Attenuator (41positon) x 8

Rear Panel MODE switch (STEREO/BRIDGE/PARALLEL) x 4

GAIN switch (+4dBu/26dB/32dB) x 1

HPF switch (OFF/20Hz/55Hz) x 1

Output Barrier strip/ch
PowerAC inlet x 1

CLIP x 8 (Red), SIGNAL x 8 (Green), MUTE x 8 (Red),

PARALLEL x 4 (Orange), BRIDGE x 4 (Orange)

DC-fault Power supply shutdown

Over current Power supply shutdown

Other: 220V-240V, 50/60Hz

(The depth is measured from the front panel surface to the

rear mounting hardware.)

Allen wrench x 1, Security cover attachment screw x 2,

3-pin Euroblock connector x 8, Owner’s manual

≥60dB

Korea: 220V, 60Hz
China: 220V, 50Hz

IPA8200 Owner’s Manual

57

Specifications

Block Diagram

+
–

G

CH A, C, E, G

+
–

G

CH B, D, F, H

STEREO

BRIDGE

PARALLEL
STEREO

BRIDGE

PARALLEL

MODE

Dimensions

ATTENUATOR

HA

ATTENUATOR

HA

MUTE

MUTE

GAIN

GAIN

HPF

Fc=20Hz

HPF

Fc=55Hz

HPF

Fc=20Hz

HPF

Fc=55Hz

HPF

HPF

STEREO

BRIDGE

PARALLEL

MODE

Comp.

Comp.

Clip Level

BA

Detect

Level

BA Inv

Detect

P.A m p

P.A m p

Signal Level

Detect

Signal Level

Detect

Output

Filter

SPEAKERS

–
+
–
+

A, C, E, G

B, D, F, H

480 (18-7/8")

377.7 (14-7/8")

406.5 (16")

88 (3-7/16")

Unit: mm (inch)

IPA8200 Owner’s Manual

58

Current Draw

Line Current (A) Power (W) Thermal Dissipation

100/120V 230/240V In Out Dissipated Btu/h kcal/h

Idle 0.8 0.4 69 0 69 235 59

1/8 power

1/3 power

1/8 power is typical of program material with occasional clipping. Refer to these figures for most applications.
1/3 power represents program material with extremely heavy clipping.
Test signal: Pink Noise, bandwidth limited from 22Hz to 22kHz
1W = 0.860kcal/h, 1BTU = 0.252kcal
Note that Line Voltage [V] x Line Current [A] = [VA], not equals to [W].

Inrush current: 11A (100V), 13A (120V), 26A (240V)

8Ω/ch 1.9 1.0 189 100 89 304 77
4Ω/ch 3.3 1.5 327 200 127 433 109
8Ω/ch 3.9 1.8 389 267 122 417 105
4Ω/ch 7.7 3.3 774 533 241 821 207

Specifications

IPA8200 Owner’s Manual

59

MEMO

IPA8200 Owner’s Manual

60

EN

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products
should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance
with your national legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on
human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste disposal
service or the point of sale where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or
dealer and ask for the correct method of disposal.

DE

FR

Verbraucherinformation zur Sammlung und Entsorgung alter Elektrogeräte

Befindet sich dieses Symbol auf den Produkten, der Verpackung und/oder beiliegenden Unterlagen, so sollten benutzte elektri­sche Geräte nicht mit dem normalen Haushaltsabfall entsorgt werden.
In Übereinstimmung mit Ihren nationalen Bestimmungen und den Richtlinien 2002/96/EC, bringen Sie alte Geräte bitte zur
fachgerechten Entsorgung, Wiederaufbereitung und Wiederverwendung zu den entsprechenden Sammelstellen.

Durch die fachgerechte Entsorgung der Elektrogeräte helfen Sie, wertvolle Ressourcen zu schützen und verhindern mögliche
negative Auswirkungen auf die menschliche Gesundheit und die Umwelt, die andernfalls durch unsachgerechte Müllentsor­gung auftreten könnten.

Für weitere Informationen zum Sammeln und Wiederaufbereiten alter Elektrogeräte, kontaktieren Sie bitte Ihre örtliche Stadt­oder Gemeindeverwaltung, Ihren Abfallentsorgungsdienst oder die Verkaufsstelle der Artikel.

[Information für geschäftliche Anwender in der Europäischen Union]

Wenn Sie Elektrogeräte ausrangieren möchten, kontaktieren Sie bitte Ihren Händler oder Zulieferer für weitere Informationen.

[Entsorgungsinformation für Länder außerhalb der Europäischen Union]

Dieses Symbol gilt nur innerhalb der Europäischen Union. Wenn Sie solche Artikel ausrangieren möchten, kontaktieren Sie
bitte Ihre örtlichen Behörden oder Ihren Händler und fragen Sie nach der sachgerechten Entsorgungsmethode.

Information concernant la Collecte et le Traitement des déchets d’équipements

électriques et électroniques

Le symbole sur les produits, l’emballage et/ou les documents joints signifie que les produits électriques ou électroniques usa­gés ne doivent pas être mélangés avec les déchets domestiques habituels.
Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et électroniques,
veuillez les déposer aux points de collecte prévus à cet effet, conformément à la réglementation nationale et aux Directives
2002/96/EC.

En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous contribuerez à la sauve­garde de précieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui pourraient advenir lors
d’un traitement inapproprié des déchets.

Pour plus d’informations à propos de la collecte et du recyclage des déchets d’équipements électriques et électroniques,
veuillez contacter votre municipalité, votre service de traitement des déchets ou le point de vente où vous avez acheté les pro­duits.

[Pour les professionnels dans l’Union Européenne]

Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques veuillez contacter votre vendeur
ou fournisseur pour plus d’informations.

[Information sur le traitement dans d’autres pays en dehors de l’Union Européenne]

Ce symbole est seulement valables dans l’Union Européenne. Si vous souhaitez vous débarrasser de déchets d’équipements
électriques et électroniques, veuillez contacter les autorités locales ou votre fournisseur et demander la méthode de traitement
appropriée.

IPA8200 Owner’s Manual

61

ES

Información para Usuarios sobre Recolección

Este símbolo en los productos, embalaje, y/o documentación que se acompañe significa que los productos electrónicos y eléc­tricos usados no deben ser mezclados con desechos hogareños corrientes.
Para el tratamiento, recuperación y reciclado apropiado de los productos viejos, por favor llévelos a puntos de recolección apli­cables, de acuerdo a su legislación nacional y las directivas 2002/96/EC.

Al disponer de estos productos correctamente, ayudará a ahorrar recursos valiosos y a prevenir cualquier potencial efecto
negativo sobre la salud humana y el medio ambiente, el cual podría surgir de un inapropiado manejo de los desechos.

Para mayor información sobre recolección y reciclado de productos viejos, por favor contacte a su municipio local, su servicio
de gestión de residuos o el punto de venta en el cual usted adquirió los artículos.

y Disposición de Equipamiento Viejo

[Para usuarios de negocios en la Unión Europea]

Si usted desea deshacerse de equipamiento eléctrico y electrónico, por favor contacte a su vendedor o proveedor para mayor
información.

[Información sobre la Disposición en otros países fuera de la Unión Europea]

Este símbolo sólo es válidos en la Unión Europea. Si desea deshacerse de estos artículos, por favor contacte a sus autorida­des locales y pregunte por el método correcto de disposición.

IT

Informazioni per gli utenti sulla raccolta e lo smaltimento di vecchia attrezzatura

Questo simbolo sui prodotti, sull’imballaggio, e/o sui documenti che li accompagnano significa che i prodotti elettriche e elettro­niche non dovrebbero essere mischiati con i rifiuti domestici generici.
Per il trattamento, recupero e riciclaggio appropriati di vecchi prodotti, li porti, prego, ai punti di raccolta appropriati, in accordo
con la Sua legislazione nazionale e le direttive 2002/96/CE.

Smaltendo correttamente questi prodotti, Lei aiuterà a salvare risorse preziose e a prevenire alcuni potenziali effetti negativi
sulla salute umana e l’ambiente, che altrimenti potrebbero sorgere dal trattamento improprio dei rifiuti.

Per ulteriori informazioni sulla raccolta e il riciclaggio di vecchi prodotti, prego contatti la Sua amministrazione comunale locale,
il Suo servizio di smaltimento dei rifiuti o il punto vendita dove Lei ha acquistato gli articoli.

[Per utenti imprenditori dell’Unione europea]

Se Lei desidera disfarsi di attrezzatura elettrica ed elettronica, prego contatti il Suo rivenditore o fornitore per ulteriori informa­zioni.

[Informazioni sullo smaltimento negli altri Paesi al di fuori dell’Unione europea]

Questo simbolo è validi solamente nell’Unione europea. Se Lei desidera disfarsi di questi articoli, prego contatti le Sue autorità
locali o il rivenditore e richieda la corretta modalità di smaltimento.

IPA8200 Owner’s Manual

62

For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou
au distributeur le plus proche de vous figurant dans la liste suivante.

Para detalles sobre productos, contacte su tienda Yamaha más cercana
o el distribuidor autorizado que se lista debajo.

Per ulteriori dettagli sui prodotti, rivolgersi al più vicino rappresentante
Yamaha oppure a uno dei distributori autorizzati elencati di seguito.

NORTH AMERICA

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,
M1S 3R1, Canada
Tel: [phone]

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620,
U.S.A.
Tel: [phone]

CENTRAL & SOUTH AMERICA

MEXICO

Yamaha de México S.A. de C.V.

Calz. Javier Rojo Gómez #1149,
Col. Guadalupe del Moral
C.P. 09300, México, D.F., México
Tel: [phone]

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,
CEP 04534-013 Sao Paulo, SP. BRAZIL
Tel: [phone]

ARGENTINA

Yamaha Music Latin America, S.A.
Sucursal de Argentina

Olga Cossettini 1553, Piso 4 Norte
Madero Este-C1107CEK
Buenos Aires, Argentina
Tel: [phone]

PAN AMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, Panamá
Tel: [phone]

EUROPE

THE UNITED KINGDOM

Yamaha Music U.K. Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, England
Tel: [phone]

GERMANY

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: [phone]

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH
Branch Switzerland in Zürich

Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: [phone]

AUSTRIA

Yamaha Music Europe GmbH Branch Austria

Schleiergasse 20, A-1100 Wien, Austria
Tel: [phone]

CZECH REPUBLIC/SLOVAKIA/
HUNGARY/SLOVENIA

Yamaha Music Europe GmbH Branch Austria

Schleiergasse 20, A-1100 Wien, Austria
Tel: [phone]

POLAND

Yamaha Music Europe GmbH
Branch Sp.z o.o. Oddzial w Polsce

ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland
Tel: [phone]

THE NETHERLANDS/
BELGIUM/LUXEMBOURG

Yamaha Music Europe Branch Benelux

Clarissenhof 5-b, 4133 AB Vianen, The Netherlands
Tel: [phone]

FRANCE

Yamaha Musique France

BP 70-77312 Marne-la-Vallée Cedex 2, France
Tel: [phone]

ITALY

Yamaha Musica Italia S.P.A.
Combo Division

Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: [phone]

SPAIN/PORTUGAL

Yamaha Música Ibérica, S.A.

Ctra. de la Coruna km. 17, 200, 28230
Las Rozas (Madrid), Spain
Tel: [phone]

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1, Box 30053
S-400 43 Göteborg, Sweden
Tel: [phone]

DENMARK

YS Copenhagen Liaison Office

Generatorvej 6A, DK-2730 Herlev, Denmark
Tel: [phone]

NORWAY

Norsk filial av Yamaha Scandinavia AB

Grini Næringspark 1, N-1345 Østerås, Norway
Tel: [phone]

RUSSIA

Yamaha Music (Russia)

Office 4015, entrance 2, 21/5 Kuznetskii
Most street, Moscow, 107996, Russia
Tel: [phone]

OTHER EUROPEAN COUNTRIES

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: [phone]

AFRICA

Yamaha Corporation,
Asia-Pacific Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: [phone]

MIDDLE EAST

TURKEY/CYPRUS

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: [phone]

OTHER COUNTRIES

Yamaha Music Gulf FZE

LOB 16-513, P.O.Box 17328, Jubel Ali,
Dubai, United Arab Emirates
Tel: [phone]

ASIA

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
Tel: [phone]

INDIA

Yamaha Music India Pvt. Ltd.

5F Ambience Corporate Tower Ambience Mall Complex
Ambience Island, NH-8, Gurgaon-122001, Haryana, India

Tel: [phone]

INDONESIA

PT. Yamaha Music Indonesia (Distributor)
PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: [phone]

KOREA

Yamaha Music Korea Ltd.

8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
Tel: [phone]

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Petaling Jaya, Selangor, Malaysia
Tel: [phone]

SINGAPORE

Yamaha Music Asia Pte., Ltd.

#03-11 A-Z Building
140 Paya Lebor Road, Singapore 409015
Tel: [phone]

TAIWAN

Yamaha KHS Music Co., Ltd.

3F, #6, Sec.2, Nan Jing E. Rd. Taipei.
Taiwan 104, R.O.C.
Tel: [phone]

THAILAND

Siam Music Yamaha Co., Ltd.

4, 6, 15 and 16
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: [phone]

th

floor, Siam Motors Building,

OTHER ASIAN COUNTRIES

Yamaha Corporation,
Asia-Pacific Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: [phone]

OCEANIA

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: [phone]

COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,
Asia-Pacific Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: [phone]

PA24

HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division

Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
Tel: [phone]

IPA8200 Owner’s Manual

63

Yamaha Pro Audio global web site:

http://www.yamahaproaudio.com/

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

© 2009 Yamaha Corporation

001PO-03C0