XPiQ inc JPP130PT09, JPP130PT07, JPP130PT06, JPP130PT05, JPP130PT04 Datasheet
...
•
•
High Power Density
•
Small Footprint
•
Up to Five DC Outputs
•
Wide Adjustment on 2 Outputs
•
Short Circuit Protection
•
Power Fail Detect Signal
•
Active PFC - Meets EN61000-3-2, -3
Input
AC Input Voltage • 90-264 VAC (120-370 VDC)
Input Frequency • 47-63 Hz
Power Factor • 0.98 typical
Inrush Current • 35 A at 115 VAC, 70 A at 230 VAC
Input Current • 2.1 A max at 115 VAC,
1.1 A max at 230 VAC
Output
Output Voltage • See Table
Output Voltage • User adjustable, See Note 3
Adjustment
Output Power • 130 Watts
Minimum Load • 0.8 A for V1 output to regulate V5
Line Regulation • ±0.5% max
Total Regulation • ±3% for V2, ±2% for all other outputs
Ripple & Noise • 65 mV for V1, 1% peak-peak on all
other outputs
Transient Response • 4% max deviation, 500 µs recovery
time for a 25% load change
Temperature • 0.04%/°C
Coefficient
Hold Up Time • >15 ms min
Remote Sense • On 3.3 V output only, compensates
for up to 0.5 V drop
Overvoltage • On V1 & V5 only
Protection 112% to 132% of nominal
Overcurrent • On V1 and V5 only.
Protection Re-cycle input to reset
General
Efficiency • 75% typical
Power Density • 7.2 W/in3
MTBF • 200,000 hrs min
Isolation Voltage • 3000 VAC Input to Output
1500 VAC Input to Ground
500 VAC Output to Ground
Signals • PFD = TTL low gives warning of
at least 10 ms before V1 output drops
below 95% of nominal. This signal also
provides a minimum of 100 ms delay
after V1 is within regulation.
Size • 3.0” x 5.0” x 1.2”
Weight • 320 g (0.71 lbs) approx.
Environmental
Operating • -10 °C to +60° C with derating
Temperature Derate linearly from 100% load at
+40 °C to 50% load at +60 °C
Cooling • 10 CFM from two 40mm diameter
fans required.
Humidity • 5 to 95% RH, non-condensing
Storage • -40 °C to +85 °C
Temperature
EMC & Safety
Safety Approvals • UL60950, CSA C22.2 No 60950,
EN60950, CE Mark LVD
EMC • Meets EN61000-3-2, -3
EN61000-4-2, -3, -4, -5, -6, -8, -11
EN55022 FCC Part 15 &
VCCI Class B conducted,
Class A radiated
130 Watts
JPP130 Series
AC/DC Open Frame
Specification
•
Intelligent Design Quality Product
XPiQ inc.
PH: 508 429.9883
FAX: 800 226.2100
Email: sales@xpiq.com
Holliston, MA 01746 USA
www.XPiQ.com
Mechanical Details
OUTPUT VOLTAGE & CURRENT RATINGS JPP130
Output Output Output
(4)
Output
(4)
Output Model
V1 V2 V3 V4 V5
(2)
Number
+5.1 V/12.0 A +12 V/6.0 A JPP130PD02
+5.1 V/12.0 A +15 V/4.8 A JPP130PD03
+5.1 V/12.0 A +24 V/3.0 A JPP130PD04
+5.1 V/12.0 A +12 V/6.0 A 3.3 V/12.0 A JPP130PT01
+5.1 V/12.0 A +15 V/4.8 A 3.3 V/12.0 A JPP130PT02
+5.1 V/12.0 A +24 V/3.0 A 3.3 V/12.0 A JPP130PT03
+5.1 V/12.0 A +12 V/6.0 A +5 to +24 V/1.0 A JPP130PT04
+5.1 V/12.0 A +15 V/4.8 A +5 to +24 V/1.0 A JPP130PT05
+5.1 V/12.0 A +24 V/3.0 A +5 to +24 V/1.0 A JPP130PT06
+5.1 V/12.0 A +12 V/6.0 A -5 to -24 V/1.0 A JPP130PT07
+5.1 V/12.0 A +15 V/4.8 A -5 to -24 V/1.0 A JPP130PT08
+5.1 V/12.0 A +24 V/3.0 A -5 to -24 V/1.0 A JPP130PT09
+5.1 V/12.0 A +12 V/6.0 A +5 to +24 V/1.0 A 3.3 V/12.0 A JPP130PQ01
+5.1 V/12.0 A +15 V/4.8 A +5 to +24 V/1.0 A 3.3 V/12.0 A JPP130PQ02
+5.1 V/12.0 A +24 V/3.0 A +5 to +24 V/1.0 A 3.3 V/12.0 A JPP130PQ03
+5.1 V/12.0 A +12 V/6.0 A -5 to -24 V/1.0 A 3.3 V/12.0 A JPP130PQ04
+5.1 V/12.0 A +15 V/4.8 A -5 to -24 V/1.0 A 3.3 V/12.0 A JPP130PQ05
+5.1 V/12.0 A +24 V/3.0 A -5 to -24 V/1.0 A 3.3 V/12.0 A JPP130PQ06
+5.1 V/12.0 A +12 V/6.0 A +5 to +24 V/1.0 A -5 to -24 V/1.0 A JPP130PQ07
+5.1 V/12.0 A +15 V/4.8 A +5 to +24 V/1.0 A -5 to -24 V/1.0 A JPP130PQ08
+5.1 V/12.0 A +24 V/3.0 A +5 to +24 V/1.0 A -5 to -24 V/1.0 A JPP130PQ09
+5.1 V/12.0 A +12 V/6.0 A +5 to +24 V/1.0 A -5 to -24 V/1.0 A 3.3 V/12.0 A JPP130PM01
+5.1 V/12.0 A +15 V/4.8 A +5 to +24 V/1.0 A -5 to -24 V/1.0 A 3.3 V/12.0 A JPP130PM02
+5.1 V/12.0 A +24 V/3.0 A +5 to +24 V/1.0 A -5 to -24 V/1.0 A 3.3 V/12.0 A JPP130PM03
P3 CONNECTIONS
Pin Function
1 - Sense (V0)
2 + Sense (V0)
3 PFD Signal
4 Com
1. Minimum 10 CFM required for 130 W operation.
2. V1 & V5 combined output power not to exceed 65 W, V2 & V3 & V4 combined output power not to exceed 65 W, V3 & V4 combined output
power not to exceed 30 W.
3. Adjustment range: V1 & V5 are adjustable ±10%, V3 & V4 are trimmable 5-24 VDC and are factory set to 12 VDC nominal.
Accessible trim pots are assigned as VR1 for V1, VR2 for V5, VR3 for V3, VR4 for V4 and V2 is fixed.
VR3 & VR4 trim pots are SMD types and are located underneath PCB.
4. Zener diodes on underside of PCB run hot during operation. Supply should be mounted on 8mm/0.32” standoffs or greater and 20% of the
10 CFM airflow should be directed below the supply.
5. Part numbers in bold are standard stock models, others are build to order.
Notes
•
P4 CONNECTIONS
Pin Function
1V5
2 Com
NOTE: P4 only applies to
models which have an
Output 5 shown in the
Output Voltage & Current
Ratings table above.
P2 CONNECTIONS
Pin Function
1V1
2 Com
3 Com
4 V3 or N/C
5 V4 or N/C
6 V2 or N/C
P1 CONNECTIONS
Pin Function
1 Live
2 Neutral
Connectors
P1 Mating Connector : Molex 09-50-3031 and 2878 series crimp terminal or equivalent.
P2 & P4 Connectors can accept 18-12 AWG electric wires.
P3 Mating Connector : Molex 22-01-1043 and 40445 series crimp terminals or equivalent.
Dimensions in inches (mm).
Tolerance ±0.02 (±0.5) max.
Direction
of airflow
PH: 508 429.9883
FAX: 800 226.2100
Email: sales@xpiq.com
Holliston, MA 01746 USA
www.XPiQ.com
Derating Chart
Loading...