Page 1
Installing the hard drive
Static Electricity Precautions
Leave the printer plugged into its power outlet; this preserves a
■
ground path for static discharges.
T ouch the printer’s bare metal frame often to discharge static electricity
■
from your body.
Handle the circuit board by the edges only.
■
Do not lay the board on a metal surface.
■
Make the least possible movements to avoid generating static eletricity.
■
Avoid wearing wool, nylon, or polyester clothing; they generate static
■
eletricity.
Tools required
■
Phillips
Installing the hard drive
Turn off the printer. Disconnect the rear panel cables if they obstruct
1.
your work.
®
screwdriver
Z840-3-02
Installing the hard drive
3
Page 2
4
03
2.
If your printer has a network card, remove it and the metal plate above
it. Otherwise, remove both metal plates on the back of the printer.
Z840-3-
Remove the hard disk from its packaging.
3.
Phaser 840 Color Printer
Z840-3-04
4.
Slide the hard drive into the upper card slot and and firmly push it into
place.
Z840-3-05
Page 3
5.
Secure the hard disk in place with the mounting screws and make sur e
that the screws are tight.
Insert the network card, or attach the lower cover plate and secure with
6.
the mounting screws.
,
7.
Reconnect any cables that were disconnected, and turn on the printer.
Z840-3-08
Installing the hard drive
5
Page 4
6
Page Count:
Serial Number:
Adode® PostScript®:
Firmware:
Feature set:
Installed RAM:
ROM Fonts Available:
IDE Disk:
SCSI Disk:
Print Quality:
TekColor® Correction:
Parallel Port:
Ethernet®:
504
Ip3-63
OS 1.14 / PS 8.23 / Eng 8
Full
128 MBytes
164 Fonts
2067 MB total, 2
Not Connected
Enhanced
Automatic
Language:Postscript®
Protocol:Binary
Handshake: Bi-directional
PhaserShare® Series B B
8.
From the printer’s front panel, print a Startup Page and check it to
make sure that the hard drive is present.
Phaser® 840 Color Printer
Startup
Phaser Swift
Printer Name:
504
Page Count:
Ip3-63
Serial Number:
Adode® PostScript®:
OS 1.14 / PS 8.23 / Eng 8.51 / Net 5.55
Firmware:
Full
Feature set:
128 MBytes
Installed RAM:
164 Fonts
ROM Fonts Available:
2067 MB total, 2001 MB free
IDE Disk:
Not Connected
SCSI Disk:
Enhanced
Print Quality:
Automatic
TekColor® Correction:
Language:Postscript®
Parallel Port:
Protocol:Binary
Handshake: Bi-directional
PhaserShare® Series B Built-In Ethernet® Interface
Ethernet®:
10BASE-T, 08:00:11:08:59:53
LaserWriter@WV 60/61, Node ID: 5000.200
EtherTalk®:
Operating Mode: Print Server (TEK085953)
NetWare®:
Connection Mode:NDS (No Preferred DS Tree)
Networks: 0(802.2), 98 (802.3), 0 (Ethernet ll), 0 (SNAP)
Status Message: Can't find NDS tree, will retry in 60 sec
Address: 134:62:91:178
TCP/IP:
Network Mask: 255.255.255.0
Gateway: 134:62:91:1
Broadcast: 134:62.91.255
IPAddress Source: Front Panel
Adobe Systems Incorporated which may be
ANTONE® and PANTONE CALIBRATED are trademarks of Pantone, Inc.
Z840-3-10
9.
At your computer, reconfigure the printer driver. Refer to
"Configuring the driver" in the Phaser 840 Color Printer Setup Guide.
Z840-3-09
Phaser 840 Color Printer
Loading...