Xerox DocuPrint 100 EPS, DocuPrint 115, DocuPrint 115 EPS, DocuPrint 135 EPS, DocuPrint 155 EPS Reference Manual
...
Duty cycle
Targeted impressions per month on the Xerox
DocuPrint 100/115/135/155/180 EPS:
Note: Usage outside these ranges may vary the
service frequency.
Performance
Reliability performance of the Xerox DocuPrint 100/
115/135/155/180 EPS for the targeted impressions per
month:
Note: Variables other than monthly print volume affect
the average number of service calls. Please contact
your local Xerox representative for more information.
Resolution
DP 155 and 180: 600 by 2400 dots per inch (dpi)
DP 100, 115, and 135: 600 by 600 dots per inch (dpi)
Speed
The speed at which data can be printed on the Xerox
DocuPrint 100/115/135/155/180 EPS:
Note: Throughput rates can vary depending upon job
complexity and system configuration.
* Requires optional 7 by 10 inch enablement kit.
Paper handling
• Paper weights: 16 lbs. / 65 gsm bond to 110 lbs. /
200 gsm index cut-shee t weights
• Paper sizes:
– 8 x 10 in. / 203 x 254 mm to
14.33 x 17 in. / 364 by 432 mm, including A4 and A3
– 7 x 10 in. / 178 x 254 mm with optional 7 x 10 in.
enablement kit
Input
• Main tray (Tray 1): 1100 sheet capacity of 20 lbs. /
80 gsm bond paper
• Auxiliary tray (Tray 2): 600 sheet capacity of 20
lbs. / 80 gsm bond paper
The Xerox DocuPrint 100/115/135/155/180 EPS may
have up to six input trays: two processor trays and two,
three, or four high-capacity feeder trays.
Output
• Output bin: Each output bin has a capacity of 2500
sheets of 20 lbs. / 80 gsm bond with offset
capability.
Two output bins are standard, with up to two
additional bins available as options.
• Sample tray: 100 sheets of 20 lbs. / 80 gsm bond
Refer to Helpful Facts About Paper to help in selection
of preprinted forms, perforated stock and labels.
Controller components
• Processor (system unit):
– One or two UltraSPARC central processing unit
(CPU) modules
– 1 or 2 GB of memory (one or two 1-GB Dual In-line
Memory Modules, or DIMMs)
– 36 or 73 GB hard disk drive
– High-density, read-only DVD-ROM drive
– Diskette drive: uses 3.5 inch, 1.44 MB, double-sided,
high-density diskettes
–Ethernet
– 1 or 2 Printer Controller Interface (PCI) boards
– PGx64 or XVR-100 video graphics board
• Universal Serial Bus (USB) keyboard and mouse
• 17-inch flat panel mo nitor
Note: This configuration may change due to the Xerox
policy of staying up to date with current technology.
Supported client workstations
Xerox DP 100/115/135/155/180 EPS supports the
following types of networked client workstations and
operating systems:
• Sun Workstation running Solaris 2.3 or higher
• PC running MS-DOS 5.0 or higher, using Ethernet
with TCP/IP or Novell NetWare, and Windows 95/
98, NT, Millennium, 2000, or XP
• PC running MS-DOS 5.0 or higher, with one or more
of the following TCP/IP packages:
– PC/TCP Network Softw are by FTP Software, Inc.
– Pathway Access by Wollongong Group, Inc.
– PC-NFS by Sun Select
• Apple Macintosh, System 7 or higher, using
AppleTalk through EtherTalk
• Any system that supports RFC -1179 lpr/lpd
PDL compatibility
The system interprets the following data formats:
• PostScript levels 2 and 3
• PCL5e and PCL6
• LCDS
• ASCII
• PDF
• TI FF
• VIPP
• IPDS (currently not available)
Interface requirements
One or more of the fo llowing network comm unications
systems may be used to transport documents from a
client or host to the printing system.
• Ethernet LAN runni ng TCP/IP, AppleTalk, or Novell
NetWare network protoc ol software
• Online – Bus and tag supporting IBM 3211/4245
interface*
• Token ring LAN running TCP/IP, Novell 3.x, or
AppleTalk network protocol softw are*
* Requires additional equipment .
Installation considerations
• Data cable: The controller can be separated up to
the length of the data interface cables that connects
them.
– 20 foot / 6.1 meters, or
– Optional 50 foot / 15.2 meters
• Power cable lengths are as follows:
• Cable length loss must be factored in if equipment is
installed in a raised -floor environme nt. Part of the
cable length is routed inside the equipment to
connect with interior power receptacles.
• All power cords attach to the back of the printer.
Listed below are t he distances of the pri nter power
cord attachments from the left end of the printer as
you face it:
– Cord #1: 36 inches / 914 mm
– Cord #2: 23 inches / 584 mm (DP 155 & 180)
Special considerations
• Transference of the bl ack toner to poly-vin yl
surfaces is a common occurrence.
• When printing edge to edge, there is a 3 to 4.8 mm
border around the sheet where degraded image
quality may occur.
• Edge marking should be no closer than 4.8 mm from
the edge of the sheet.
• Xerox carbonless paper is approved for Xerox
DocuPrint 100/115/135/155/180 EPS. Refer to the
Xerox Supplies Catalog for the reorder numbers.
• Appearance of very sma ll spots is a common
occurrence on al l xerographic prin ters. Consult you r
Xerox service representative for details on
acceptable spot occurrence specifications.
Printing system Minimum Maximum
DP100 800 thousand 3 million
DP115 1 million 3.5 million
DP135 1.2 million 4 million
DP155 1.4 million 4.5 million
DP180 1.8 million 6 million
Average
monthly
print
volume
Average
service
calls per
month
DP100
Average
service
calls per
month
DP115
Average
service
calls per
month
DP135
Average
service
calls per
month
DP155
Average
service
calls per
month
DP180
1
million
2.7 2.6 2.5 2.6 2.4
2
million
5.4 5.2 5.0 5.2 4.8
3
million
8.1 7.8 7.5 7.8 7.2
4
million
-- -- 10.0 10.4 9.6
5
million
-- -- -- -- 12
6
million
-- -- -- -- 14.4
Printing system
Pages per minute
(standard)
Pages per minute
(using 7 x 10 in. /
178 x 254 mm
paper) *
DP100 100 100
DP115 115 115
DP135 135 154
DP155 155 155
DP180 180 206
Controller: 8 feet / 2.4 m
Printer: 15 feet / 4.6 m
Environmental requirements
Supplies
Notes:
• Expected dry ink yield is based on a 7 percent area
coverage, 8.5 by 11 inch or A4 paper, and varies
depending on area coverage of the application, as
well as the darkness settings of the printer.
• Contact your local Xerox representative for supplies
ordering information.
Recommended Minimum Maximum
Operating
temperature
72o +/- 4o F
22
o
+/- 2o C
50
o
F
10
o
C
85
o
F
29
o
C
Humidity 45% +/- 10% RH 30% RH 65 % RH
Normal Maximum
Altitude Up to 6,000 feet /
1,830 m above
sea level
9,000 feet /
2,743 m above
sea level
Heat dissipation Standby Running
Printer 4,454 BTU/hr.
(Fuser on)
2,700 BTU/hr.
(Energy saver)
155/180: 32,770
BTU/hr
100/115/135:
28,140 BTU/hr.
Processor and
monitor (Sun
Blade
TM
)
SB 1000/2000: 1,10 0 BTU/hr.
SB 2500: 1,570 BTU /hr.
Reorder number
Expected yield
(Prints/carton)
Dry ink US: 6R206
Europe: 6R90100
180,000
Dry ink waste
bottle
US: 93K460
Europe: 93K450
N/A
Developer US: 5R161
Europe: 5R90095
1,000,000
Fuser agent US: 8R2955
Europe: 8R90163
250,000
(1 bottle)
MICR dry ink US: 6R819 180,000
MICR
developer
US: 5R573 600,000
• In the U.S., call 1.800.822.2200 to order Xerox
supplies, including paper and other stocks.
Space requirements
Notes:
• All the dimensions are taken from the system frame
to the nearest wall or obstruction, shown in inches
and centimeters, and are absolute minimums.
• There should be a minimum of 78 inches / 198 cm
clearance from the floor to the nearest overhead
obstruction, throughout the entire area.
Depth Width Height
Controller
The following data is accurate for the Sun Blade
TM
1000/2000 and 2500 workstations, and is presented
as an example of typical space requirements for
workstations.
Stand 35.5 in.
90.2 cm
30 in.
76.2 cm
38.25 in.
97.2 cm
Processor: Sun
BladeTM 1000/2000
19.3 in.
49 cm
8.2 in.
21 cm
17.75 in.
45.1 cm
Processor: Sun
BladeTM 2500
25 in.
63.5 cm
10 in.
25.4 cm
19 in.
46.3 cm
Monitor 10 in.
25.4 cm
17 in.
43.2 cm
18.5 in.
47 cm
Printer
Space requirements (physical hardware and required
service area) for each of the printer configurations:
With inverter feeder/
stacker and 1 feeder/
stacker
114 in.
290 cm
223 in.
567 cm
With inverter feeder/
stacker and 2 feeder/
stackers
114 in.
290 cm
257 in.
652.8 cm
With inverter feeder/
stacker and 3 feeder/
stackers
114 in.
290 cm
288 in.
731 cm
With inverter feeder/
stacker, feeder/
stacker, and bypass
transport module
114 in.
290 cm
242 in.
615 cm
With inverter feeder/
stacker and 2 feeder/
stackers, and bypass
transport
114 in.
290 cm
276 in.
701 cm
• The printing system must be installed in a fixed
location with minimum clearance space of 36 inches
/ 91.4 cm around all sides of each piece of
equipment for acce ss by service personn el.
• 50 inches / 127 cm clearance space is required in
front of the printer.
• The controller must be positioned within the line of
sight of the printer for safety purposes while the
equipment is being serviced.
• Customer must use t he Xerox-supplied s tand for all
controller components. Space requirements for the
controller stand are 36 by 36 inches / 91 by 91 cm.
• For proper operation, the printer must be perfectly
level. On floors le ss than two degrees out of level, a
leveling kit must be used to level the equipment.
The printer will no t function proper ly on floors more
than two degrees out of level.
For additional s pace/configuration options, r efer to the
Xerox DocuPrint 100/115/135/155/180 EPS
Installation Planning Guide.
Electrical requirements
Notes:
• Dedicated service is required for each component.
Each power cord must have a separate circuit.
• Power requiremen ts of the bypass transpor t are
satisfied by the printer module.
Controller
(47-63 Hz)
Printer
(60 Hz)
Cord #1
155/180
printer
(60 Hz)
Cord #2
Printer
(50 Hz)
Voltage 100-240
VAC
(1 phase)
120/208
VAC; or
120/240
VAC
(2 phase)
120/208
VAC; or
120/240
VAC
(2 phase)
380, 400,
415 VAC
(3 phase)
Receptacle
NEMA part
number
5-15R 14-50R 14-30R --
Power
consumption (KVA)
Operating
mode
0.4 7.3 +
.75 per
middle
module
stacker
7.3+
.75 per
middle
module
stacker
Consult
your local
service
represent
ative
2004 by Xerox Corporation. All rights reserved.
Xerox DocuPrint
100/115/135/155/180 EPS
Customer Information
Quick Reference Card
Version 4.1
September 2004
701P42238
Loading...