Page 1
7+('2&80(17&203$1<
DC230LP NetWare® 4.x NDS Quick Install
Installation Requirements:
If this is a Token Ring installation, the Token
Ring card must be installed by your Xerox
service representative and configured before
performing this procedure. Refer to the
Ring Quick Install
If running NLSP, be sure that RIP/SAP
compatibility is configured on the same segment
as the DC230LP.
Note: For a Bindery installation, refer to the
card.
NetWare 3.1x/4.1x Bindery Quick Install
Token
card.
Before Installation:
• Perform the network installation for the
printer using the appropriate NetWare utility
(PCONSOLE or NWADMIN).
Note: Define the printer as
or
Elsewhere
• Record the following information for use
during setup at the DC230LP:
Print Server name:_______ ___ ___ ____ ___ ___
Print Server Password:___ ___ ___ ___ ___ ____ _
NDS Tree:______________________________
Remote/Other
Defined
.
NDS Name Context:_____________________
Frame Type:____________________________
Poll Interval:____________________________
This installation procedure assumes that you
know how to navigate through the menu system
on the DC230LP Control Panel. Refer to the
quick reference card,
(701P96834) for assistance.
Using the Menu System
1. Connect the DC230LP to your network
outlet or cable.
2. Access the System Administration menus:
a)
Press [Online] to take the printer off
Printer Off Line
line. displays.
b)
Press [Menu].
displays.
c)
Press [], then press [] or [] until
System
Administration
d)
Press []. displays.
e)
Use the [] and [] keys to enter
[2222].
Main Menu
>
displays.
Enter Password
>
>
Note: 2222 is the factory default password and
may be changed to suit your needs. Refer to
DC230LP System Administration Guide,
the
Network Installation and Troubleshooting
f)
Press [Enter].
displays.
System Admin
.
>
3. Access the NetWare menus:
a)
Press []. displays.
b)
Press [] until
displays.
c)
Press []. displays .
d)
Press [] until
displays.
Port Setup
Network Setup
TCP/IP
Netware
>
>
>
>
4. Enable NetWare:
a)
Press []. displays.
b)
Press []. displays.
c)
Press []. displays.
Enablement
Disabled
Enablement =
Disabled *
Enablement
Enabled
>
For assistance, contact your local Xerox Customer Support Center:
USA: 1-800-821-2797 Canada: 1-800-939-3769
Page 1 of 4
Over
Page 2
d)
Enablement
Enabled
>
Interface
Ethernet
>
Interface =
Token Ring
Interface
Token Ring
>
Enet Frame Type
Ethernet II
>
Press [Enter ]. **SAVED** displays
momentarily, followed by
.
7+('2&80(17&203$1<
DC230LP NetWare® 4.x NDS Quick Install
b)
Press [], then press [] until the
required Frame Type displays
Enet Frame Type =
(required setting)
.
f)
Press [Enter]. **SAVED** displays
momentarily, followed by
Pserver Name
(your entry)
>
.
5. Select the appropriate Interface for your
network:
Note: Token Ring will not be available as a
selection unless it has been installed and
configured.
a)
Press [] until
displays. If Ethernet is the desired
interface, go to step 6.
b)
If Token Ring is the required interface,
press [], then press [] until
displays.
c)
Press [Ente r]. **SAVED** displays
momentarily, followed by
.
6. Select the Frame Type for your network:
a)
Press [] until
displays. If Ethernet II is the desired
Frame Type, go to step 7.
c)
Press [Enter]. **SAVED** displays
momentarily, followed by
Enet Frame Type
(your entry)
IMPORTANT: During the next two steps, be
sure that the
Password
entered in PCONSOLE or NWADMIN.
Print Server Name
are exactly the same as the values
>
.
and
Print Server
7. Enter the Print Server Name:
a)
Press [] until
displays.
b)
Press []. displays.
c)
Press [] repeatedly until the cursor
reaches the end of the entry. A tone
sounds indicating when the last
character has been reached.
d)
Press [] repeatedly to delete the
current entry.
e)
Use the [] and [] keys to enter
the Print Server name.
Pserver Name
(current entry)
Pserver Name =
(current entry) *
>
8. Enter the Print Server Password:
a)
Press [] until
displays.
b)
Press []. displays.
c)
Use the [] to move to the last
character of the current entry. A tone
sounds when the last characte r has
been reached.
d)
Press [] repeatedly to delete each
character.
e)
Use the [] or [] key to enter the
first character of the password.
f)
Press [] to move to the next charac-
ter. Repeat this procedure to enter the
entire password.
g)
Press [Enter]. **SAVED** displays
momentarily, followed by your entry
Pserver Pswrd
****************
Pserver Pswrd
****************
Pserver Pswrd =
**************** *
>
.
>
9. Enter a dash [–] as the File Server name:
Page 2 of 4
Page 3
7+('2&80(17&203$1<
File Server 1
(current entry)
>
File Server 1 =
(current entry)
File Server 1
–
>
Poll Interval
(current entry)
>
Poll Interval =
(current entry) *
DC230LP NetWare® 4.x NDS Quick Install
a)
Press [] until
displays.
b)
Press []. displays.
c)
Press [] repeatedly until the cursor
reaches the end of the current entry . A
tone sounds indicating when the last
character has been reached.
d)
Press [] repeatedly to delete each
character.
e)
Use the [] and [] keys to select
the [–] (dash).
f)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
10.E nte r the Poll Interval :
a)
Press [] until
displays.
b)
Press [].
displays.
c)
Press [ ] or [] to increase or
decrease the setting to the desired
number.
d)
Press [Enter]. **SAVED** displays
momentarily, followed by
Poll Interval
(your entry)
>
11. Enter the NDS Tree name:
a)
Press [] until
displays.
b)
Press []. displays.
c)
Press [] repeatedly until the cursor
reaches the end of the entry. A tone
sounds when the last character is
reached.
d)
Press [] repeatedly to delete the
current entry.
e)
Use the [] or [] key to enter the
first character in the NDS Tree name.
f)
Press [] to move to the next charac-
ter and repeat this procedure to enter
the entire name.
g)
Press [Enter]. **SAVED** displays
momentarily, followed by
NDS Tree
(your entry)
NDS Tree
(current ent r y)
NDS Tree =
(current entry) *
>
.
12.Enter the NDS Context:
a)
Press [] until
displays.
b)
Press []. displays.
c)
>
EXAMPLE A: NDS Name Context for a Tree
with a country:
EXAMPLE B: NDS Name Context for a Tree
without a country:
Press [] repeatedly until the cursor
reaches the end of the entry. A tone
sounds indicating when the last
character has been reached.
d)
Press [] repeatedly to delete the
current entry.
e)
Use the [] or [] key to enter the
first character in the NDS Context
name.
f)
Press [] to move to the next
character and repeat this procedure to
enter the entire name. The fully
qualified name should be used for
NDS Trees with a country code.
Notice in the examples below that
there are no leading or trailing dots
OU=SALES.O=MYCOMPANY.C=US
SALES.MYCOMPANY
NDS Context
(current entry)
NDS Context =
(current entry) *
>
.
Page 3 of 4
Page 4
g)
NDS Context
(your entry)
>
Reset Required
Press ENTER key
Warming Up
Please Wait . . .
>
Press [Enter]. **SAVED** displays
momentarily, followed by
.
13.Save all the settings:
a)
Press [Online].
displays.
b)
Press [Enter].
displays. The DC230LP will reboot,
save the settings entered, and print a
Configuration Report in approximately
3 minutes.
14.Check the settings on the Configuration
Report against those entered to be sure
they are correct. The Pserver Password
does not appear on the Configuration
Report.
7+('2&80(17&203$1<
DC230LP NetWare® 4.x NDS Quick Install
15.At the client, install print drivers and map
the printer in the usual manner. Refer to
the CentreWare
with Print and Fax Services,
information.
Additional information on the NetWare setup can
be found in the
Guide, Network Installation and Troubleshoot-
.
ing
DC230LP System Administration
®
manual,
Getting Started
for additional
Page 4 of 4
©1998 Xerox Corporation
701P98457 Version 1.0, 5-98
Loading...