Xantrex XPD120-4.5 Data Sheet

Sorensen XPD Series

500–540 W

Compact 500 Watt Quarter-Rack DC Power Supply

• Analog programming

• Universal input

• Zero voltage “soft switching”

• Power factor correction (PFC)

• Front and rear connectors

• Ten-turn front panel knobs

• Remote sense with 5V line loss compensation

• LabVIEW® and LabWindows® drivers

The Sorensen XPD Series features the smallest
500-watt programmable power supply available.
The XPD Series is ideal for benchtop, ATE and
OEM applications where a wide range of output
voltage or current is needed in a compact unit.

The XPD can be combined in a mix-and-match
conguration with the quarter-rack 300-watt
HPD series and 60-watt XT series. Each unit
features zero voltage “soft switching” to virtually
eliminate switching transients. This switching
technology contributes to high efciency, low
noise, and high reliability. The XPD series also
features power factor correction (PFC) technology
to enable low current draw and to greatly reduce
generation of input current harmonics.

7.5–120 V

4.5–67 A

115 230

858.458.0223

[e-mail]

AMETEK
Programmable Power

9250 Brown Deer Road
San Diego, CA 92121-2267
USA

10252013

113

XPD Series : Product Specications

1

Output : Voltage and Current

Models 7.5-67 18-30 33-16 60-9 120-4.5

Output Ratings

Output Voltage

Output Current

2

3

Output Power 502.5 W 540 W 528 W 540 W 540 W

Line Regulation

4

Voltage 2.8 mV 3.8 mV 5.3 mV 8 mV 14 mV

Current 7.7 mA 4 mA 2.6 mA 2 mA 2 mA

Load Regulation

5

Voltage 2.8 mV 3.8 mV 5.3 mV 8 mV 14 mV

Current 11.7 mA 8 mA 6.6 mA 5.9 mA 5.5 mA

Meter Accuracy

Voltage (1% of Vmax + 1 count) 0.2 V 0.3 V 0.5 V 0.7 V 2.2 V

Current (1% of Imax + 1 count) 0.8 A 0.4 A 0.3 A 0.2 A 0.2 A

Output Noise (90-20 MHz)

Voltage (p-p) 50 mV 50 mV 75 mV 125 mV 180 mV

Output Ripple

Voltage 5 mV 5 mV 7.5 mV 10 mV 20 mV

6

Current

Drift (60 minutes)

7

Voltage (0.15% of Vmax) 11.3 mV 27 mV 49.5 mV 90 mV 180 mV

Current (0.3% of Imax) 201 mA 90 mA 48 mA 27 mA 13.5 mA

Drift (8 hours)

8

Voltage (0.03% of Vmax) 2.3 mV 5.4 mV 9.9 mV 18 mV 36 mV

Current (0.05% of Imax) 34 mA 15 mA 8 mA 4.5 mA 2.3 mA

Temperature Coefcient

9

Voltage (0.015% of Vmax/°C) 1.2 mV 2.7 mV 5 mV 9 mV 18 mV

Current (0.02% of Imax/°C) 13.4 mA 6 mA 3.2 mA 1.8 mA 0.9 mA

OVP Adjustment Range

(5% to 110% of Vmax) 0.4-8.3 V 0.9-19.8 V 1.7-36.3 V 3-66 V 6-132 V

10

Efciency

0-7.5 V 0-18 V 0-33 V 0-60 V 0-120 V

0-67 A 0-30 A 0-16 A 0-9 A 0-4.5 A

250 mA 250 mA 150 mA 150 mA 75 mA

81% 83% 85% 85% 84%

114

Specications subject to change without notice.

1. All electrical specications are represented at the full operating temperature range for all models, unless otherwise stated.

2. Minimum output voltage is < 0.15% of rated voltage at zero output setting.

3. Minimum output current is < 0.2% of rated current at zero setting when measured with rated load resistance. Front output current limited to 30 A maximum.

4. For input voltage variation over the AC input voltage range, with constant rated load.

5. For 0-100% load variation, with constant nominal line voltage.

6. Current mode noise is measured from 10% to 100% of rated output voltage, full current.

7. Maximum drift over 60 minutes with constant line, load, and temperature, after power up.

8. Maximum drift over 8 hours with constant line, load, and temperature, after 60 minute warm-up.

9. Change in output per °C change in ambient temperature, with constant line and load.

10. Typical efciency at 120 V and full output power.

11. Interface specications at 25°C ± 5°C, nominal line input of 120 Vac. Apply accuracy specications according to the following voltage program accuracy
example: Set a model 18-30 power supply to 10 V. The expected result will be within the range of 10 V ± 75 mV ± 0.12% of the set voltage of 10 V.

www.ProgrammablePower.com

XPD Series : Product Specications

1

500–540 W

XPD 500 W Internal Interface Specications with RS-232 or GPIB Interface Installed

Models 7.5-67 18-30 33-16 60-9 120-4.5

Program Accuracy

Voltage (mV) 10 +0.12% 75 +0.12% 75 +0.12% 150 +0.3% 180 +0.25%

Current (mA) 250 +0.1% 140 +0.1% 115 +0.15% 80 +0.15% 80 +0.1%

OVP (mV) 80 200 330 600 1200

Readback Accuracy

Voltage (mV) 30 (±0.12%) 75 (±0.12%) 75 (±0.2%) 150 (±0.3%) 180 (±0.25%)

Current (mA) 250 (±0.1%) 140 (±0.1%) 115 (±0.15%) 80 (±0.15%) 80 (±0.1%)

11

Input

Operational AC Input Voltage 85-264 Vac, 47-63 Hz; power factor corrected. Derate maximum output power to 450 W for AC input less than 95 V.

Maximum Input Current 7 A maximum at 100 Vac, 6 A maximum at 120 Vac, 3 A maximum at 220 Vac

General

Power Factor 0.98 minimum for full load at nominal voltage

Input Harmonic Distortion Current harmonics meet IEC 1000-3-2

Switching Frequency 125 kHz (250 kHz output ripple)

Time Delay 3 sec maximum, from power on to output stable

Voltage Mode Transient Response Time 1 ms for output voltage to recover within 0.5% of its previous level after a step change in load current of up to 50% of rated output

Maximum Voltage Differential ±300 Vdc from output to safety ground

Remote On/Off and Interlock 5-15 V signal or TTL-compatible input, selectable logic. TTL input impedance: 2 k (in series with one diode drop)

Remote Analog Programming
(Full Scale Input)

Remote Programming &
Monitoring Accuracy

Front Panel Voltage and Current Control 10-turn voltage and current potentiometers

Front Panel Voltage Control Resolution 0.02% of maximum voltage

AC Input Connector Type IEC 320 connector, appropriate power cord provided for destination country

Main Output Connector Front panel: ve-way binding posts. Maximum current limit 30 A; Rear Panel: 7.5-18 V models: Bus bars;

Approvals CE-marked units meet: EN61010-1, EN61000-6-2 and EN61000-6-4; CSA C/US certied to UL3111-1 and CSA C22.2 No 1010.1;

Voltage and current programming inputs (source must be oating): 0-10 V voltage sources. Input impedance (V and I): 20 k

1% of full scale output for the default range

33-120 V models: wire clamp connectors.

Meets USA EMC standard: FCC, part 15B, Class A; Meets Canadian EMC standard: ICES-001, Class A.

Environmental

Operating Temperature 0 to 50°C

Storage Temperature -40°C to 85°C

Humidity Range Up to 95% RH, non-condensing

Physical

Dimensions Width: 4.2” (109.2 mm)

Weight 9.0 lb (4.1 kg)

Height: 5.2” (134.7 mm)
Depth: 13” (330 mm)

Protection Features

Over voltage protection per output

Switchable remote or local sense

858.458.0223

[e-mail]

115

XPD 7.5

Series

Voltage

67

Current

(XXX)

Options

XPD Series

Model Number Description

Options and Accessories

MGA * GPIB / IEEE 488.1

MRA * RS-232 interface card

RM-XPDG-3 19-inch Rack Mount Kit

M13 Locking bushings

M13A Locking knobs

* Options cannot be combined

116

© 2009 AMETEK Programmable Power All rights reserved. AMETEK Programmable Power is the trademark of AMETEK Inc., registered in the U.S. and other countries.
Elgar, Sorensen, California Instruments, and Power Ten are trademarks of AMETEK Inc., registered in the U.S.

www.ProgrammablePower.com