World Dryer ABC-300HSR Installation Manual

Diaper Changing Station

ABC-300HSR Horizontal Recess Mounting Stainless Steel

Clad Stainless Steel Changing Station Installation Instructions (Recessed Mount)

 Instructions d’installation de la station à langer plaquée d’acier inoxydable (Installation encastrée)

 Instrucciones para instalar la estación para cambiar pañales con revestimiento de acero inoxidable

(empotrado)

WARNING

• Failure to follow these warnings and the
installation instructions could result in
serious injury or death.

• Read all instructions before installing
diaper changing station. Keep these
instructions. DO NOT discard.

AVERTISSEMENT

• Le non respect de ces avertissements
et instructions d’installation peut
entraîner des blessures graves ou la mort.

• Lisez attentivement toutes les instructions
avant d’installer la station à langer.
Conservez ces instructions. NE les jetez PAS.

World Dryer Corporation

5700 McDermott Drive
Berkeley, IL 60163 U.S.A.
800-323-0701
www.worlddryer.com

• El no seguir estas advertencias y las
instrucciones para la instalación podría
causar lesiones graves o la muerte.

• Lea todas las instrucciones antes de
instalar la estación para cambiar pañales.
Guarde estas instrucciones. NO las deseche.

ADVERTENCIA

68-10344 rev01

INSTALLATION INSTRUCTIONS

ADULT INSTALLATION REQUIRED.

A

B

TOOLS REQUIRED:

Level (A)
Measuring tape (B)

C

D

Power drill with 3/16” masonry bit (C)
Power screwdriver with bull nose phillips bit (D)
Truss head spanner bit (E)

E

• READ ALL INSTRUCTIONS BEFORE ASSEMBLY OF DIAPER CHANGING STATION.

• Unpack carton and identify all parts.

WARNING

This changer has six (6) recess mounting holes.

•

The diaper changing station is no stronger than the anchors or walls to which they are attached and, therefore,

•

MUST be firmly secured in order to support the weight they are intended to support. Contact an architect or building
contractor if any questions.

PARTS LIST

Parts Description Quantity

Hardware for recessed installation:

3” x 1/4” Wood Screws 6

Door / Wall Plate 1

21-3/8”

542 mm

3” x 1/4” Wood Screws

34-3/4”

(883 mm)

(Door)

Door / wall plate to be

mounted on outside of

A.D.A. Compliance:

13-1/8”

(333 mm)

www.worlddryer.com

restroom door.

4.4.1 Maximum Protruding Objects

4.2.5 Forward Reach

4.2.6 Parallel Approach

4.27.4 Operation
Compliant when properly installed.

1

INSTALLATION

F
Compliance

Recommended Blocking:

Wood double stud blocking is necessary. Contact an architect and
building official to make sure the blocking is adequate and complies
with building codes (Fig. a.).

For A. D. A. compliance, top of lower double stud should be 30“
(76 cm) from the floor.

1. Slide changer into blocking area and mark mounting hole location
on blocking studs.

HINT:This may require 2 additional people to help hold changer

in position while you are marking the locations.

2. Useapower drill witha3/16” bit and drill six (6) pilot holes in
the blocking studs.

3. Shim changer forasnug fit.

NOTE: If lower holes are inaccessible, remove plastic unit from steel
back by removing the 4 Truss Head Spanner Screws (fig. c). Once
steel back is attached to blocking, reconnect plastic wall to steel
back using the same spanner screws.

4. Align holes in changer with drilled holes and secure
using the wood screws. Wood screws have been
provided and are for wood only (Fig. b).

NOTE: It is installers responsibility to provide correct
fastereners for other substrates.

Recess

Mounting

Holes

or A. D. A.

30”

(76 cm)

Recess

Mounting

Holes

1"

(25.4 mm)

A. F. F

Double Stud

35 5/8" (905 mm)

Double Stud

18"

(457 mm)

Double Stud

Recess

Mounting

Holes

35 5/8"

(905 mm)

Rough-in

Fig. a

3 7/8"

(98.4 mm)

19 5/8"
(499 mm)
Rough-in

Double Stud

5. Ensure al

OPERATION:

l six (6) screws are tight.

Fig. b

Rotate base downward. Place infant on top of the changing surface. Use restraint
system as described below. After child has been changed, remove restraint system
and rotate base back up against the wall.

USE OF RESTRAINT SYSTEM:

Place child so restraint strap is located at abdomen. Rotate top of buckle upward and insert strap
in buckle. Pull strap through buckle until snug against infant. Rotate top of buckle downward to lock
the strap into place. Slide red locking tab over top of buckle (Fig. d). Reverse steps to loosen strap.

MAINTENANCE AND CLEANING:

Check all hardware and components monthly or as required to ensure hardware is tight and there
are no missing or damaged components. Take unit out of service if any component is missing or
damaged and contact customer service to order replacement parts. Do not substitute parts.
For replacement parts, contact customer service at 1-800-323-0701.

Clean by using a damp cloth with mild soap or mild multi-purpose cleaner. Do not use any strong
chemical cleaners or cleaning agents that may be hazardous to children.

WARNING

Truss Head

Spanner Screws

Top Of
Buckle

Fig. c

Locking

Tab

Fig. d

This product is intended for children up to a maximum weight of 15 kg (33 lbs.).

•

DO NOT leave the child unattended.

•

• DO NOT add a changing pad to this product.

DO NOT use this product when any part is broken, torn or missing.

•

Be aware of the risk of open fires and other sources of strong heat, such as electric bar fires, gas fires, etc. in the

•

near vicinity of the changing unit.
Avoid serious injury from falling or sliding out. Always use restraint system.

•

Adding excessive weight such as parcels, packages, or accessories to the unit or to the bag hooks that exceed the total

•

weight limit of 50 pounds (22.7 kg) may cause the unit to be unstable or may causeahazardous unstable condition to
exist.

2