Wolf GR484CG, GR486G, GR488, GR364C, GR606DGLP Installation

...

GAS RANGE

INSTALLATION GUIDE

SPECIFICATIONS, INSTALLATION, AND MORE

GAS RANGE

Contents

3 Safety Precautions

4 Specications

7 Installation

10 Troubleshooting

Features and specications are subject to change at any time without notice. Visit wolfappliance.com/specs for the most up-to-date information.

Important Note

To ensure this product is installed and operated as safely and efciently as possible, take note of the following types of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or product

damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specied.

IMPORTANT NOTE: Save these instructions for the local

electrical inspector.

2 | Wolf Customer Care 800.222.7820

SAFETY PRECAUTIONS

Product Information

Important product information including the model and serial number are listed on the product rating plate. The rating plate is located on the bottom of the control panel, at the far right, just above the oven door. Refer to the illustration below.

If service is necessary, contact Wolf Factory Certied Service with the model and serial number. For the name of the nearest Wolf Factory Certied Service or for questions regarding the installation, visit the contact & support section of our website, wolfappliance.com or call Wolf customer care at 800-222-7820.

RATING PLATE

IMPORTANT INSTRUCTIONS

WARNING

A child or adult can tip this appliance and be killed.

Verify the anti-tip device has been properly installed and engaged. Ensure the anti-tip device is re-engaged when this appliance is moved. Refer to the illustrations below for how to verify correct installation.

To reduce the risk of burns, do not move this appliance while hot.

Do not operate this appliance without the antitip device in place and engaged. Failure to do so can result in death or serious burns to children or adults.

Rating plate location

ANTI-TIP

DEVICE

Anti-tip device location

Anti-tip device engaged

ANTI-TIP

DEVICE

ENGAGED

• This appliance is equipped with casters on two

or more legs and must be installed on 1/8" (3) thick commercial grade vinyl composition oor nishing materials or equivalent.

• This appliance is not approved for downward air-

ow ventilation or air curtain equivalent.

• A minimum 20" (508) riser is required when installing

against a combustible surface.

wolfappliance.com | 3

SPECIFICATIONS

Electrical

Installation must comply with all applicable electrical codes.

Locate the electrical supply ush with the wall or oor and within the shaded area shown in the illustration on page 6. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

ELECTRICAL REQUIREMENTS

Electrical Supply grounded, 110/120 VAC, 60 Hz Service 15 amp dedicated circuit Receptacle 3-prong grounding-type Power Cord 6'

(1.8 m)

4 | Wolf Customer Care 800.222.7820

SPECIFICATIONS

Gas Supply

Installation must comply with local codes or, in the absence of local codes, with the National Fuel Gas Code.

Locate the gas supply within the shaded area shown in the illustration on the following page.

The range is equipped for use with natural or liquid propane (LP) gas. It is design certied by the Canadian Standards Association (CSA) for natural or LP gases. The product rating plate has information on the type of gas that should be used. For rating plate location, refer to the illustration below. If this information does not agree with the type of gas available, check with the local gas supplier. The gas pressure regulator is built into the unit.

GAS REQUIREMENTS

NATURAL GAS WC

Supply Pressure 5" (12.5 mb) Min Line Pressure 7" (17.5 mb) Max Regulator Pressure 14" (34.9 mb), .5 psi (3.5 kPa)

LP GAS WC

Supply Pressure 10" (25 mb) Min Line Pressure 11" (27.4 mb) Max Regulator Pressure 14" (34.9 mb), .5 psi (3.5 kPa)

The range must be connected to a regulated gas supply. The supply line must be equipped with an approved external gas shut-off valve located near the range in an accessible location. Do not block access to the shut-off valve. Refer to the illustration below.

A gas supply of range. If local codes permit, a certied, 3'

/4" (19) ID exible metal appliance connector is recom-

or mended to connect the units

/4" (19) ID line must be provided to the

(.9 m) long,

/2" NPT female inlet to the

/2" (13)

gas supply line. Pipe joint compounds, suitable for use with natural or LP gas should be used.

The appliance and its shut-off valve must be disconnected from the gas supply piping system during any pressure testing of the system at test pressures in excess of .5 psi

(3.5 kPa)

. The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the system at test pressures equal to or less than .5 psi

Wolf natural gas ranges will function up to 8,600'

(3.5 kPa).

(2621 m) in

altitude without adjustment. If the installation exceeds this elevation, contact an authorized Wolf dealer for a high altitude conversion kit. LP models do not require conversion.

RATING PLATE

Rating plate location

SHUT-OFF VALVE

OPEN POSITION

GAS SUPPLYTO APPLIANCE

Gas shut-off valve

wolfappliance.com | 5

SPECIFICATIONS

Gas Range

INSTALLATION

13"

(330)

LOCATION OF GAS AND ELECTRICAL EXTENDS

ON FLOOR

37" (940)

TO COOKING

SURFACE

18"

(457)

(152)

OPENING WIDTH

53/4"

(146)

73/4" (197)

30" (762) TO 36" (914)

TO BOTTOM OF

VENTILATION HOOD

12"

(305)

10" (254)

2" (51)

(76)

*Without ventilation hood, 42" (1067) minimum clearance countertop to combustible materials, charbroiler and GR488 require non-combustible materials.

NOTE: Shaded area above countertop indicates minimum clearance to combustible surfaces, combustible materials cannot be located within this area. For island installation, 12"

(305) minimum clearance back of range to combustible rear wall above countertop.

OPENING WIDTH

FRONT VIEWSIDE VIEW

12"

(305) GAS5"(127)

30" Model 30" (762) 36" Model 36" (914) 48" Model 48" (1219) 60" Model 601/4" (1530)

6 | Wolf Customer Care 800.222.7820

INSTALLATION

SPRING HINGES

SPRING HINGE

Preparation

Before moving the range, protect any nished ooring and secure oven door(s) closed to prevent damage.

To lighten the load or to t through a door way, the oven door(s) can be removed. Only remove if necessary. Do not remove the griddle or any other component. Door removal should only be done by a certied installer or service technician.

For removal, a hinge pin will be inserted into the appropriate hinge shown in the illustrations below. The pin(s) are located inside the oven door. For single oven ranges, the hinge pin must be inserted in the right hinge. For double oven ranges, the pins must be placed in the outer two hinges.

CAUTION

Failure to insert the hinge pin in the appropriate hinge arm will cause damage to the range.

OVEN DOOR REMOVAL

1 Insert the hinge pin into the appropriate hinge.

2 Remove the lower kickplate assembly to access the

lower hinge retainer mounting screws.

3 Open the oven door and remove both upper and lower

hinge retainer mounting screws. The oven gasket may have to be moved slightly to access the bottom screws.

4 Move the hinge retainer plate forward slightly. The hinge

retainer plate will remain on the door hinge after the mounting screws have been removed.

5 Carefully close the oven door to approximately 60°, then

lift the door up and out. A slight rocking motion may be required for removal.

UPPER

MOUNTING

SCREW

HINGE

RETAINER

PLATE

HINGE

Single oven ranges

SPRING HINGES

Double oven ranges

KICKPLATE

Oven door removal

wolfappliance.com | 7

INSTALLATION

Placement

Do not lift or carry the oven door by the door handle. The range has rear casters which allow for easy movement by lifting the front of the unit.

Use an appliance dolly to move the range near the opening. Remove and recycle packing materials. Do not discard the anti-tip bracket supplied with the range.

If a riser has been specied, refer to the installation instructions packaged with the riser. The riser must be installed before the range is installed.

Leveling

Raise the range to its desired height by adjusting the front legs and rear casters. The front legs can be adjusted by rotating the hex agonal leg clockwise to raise and counterclockwise to lower. The rear casters can be adjusted by rotating the wheel assembly.

8 | Wolf Customer Care 800.222.7820

INSTALLATION

7/8" (22) MAX

ANTI-TIP

BOLT

Anti-Tip Bracket

To prevent the range from tipping forward, the anti-tip bracket must be installed. To ensure the anti-tip bolt engages the bracket, position the bracket 3"

(76) from the

left side of the opening. Refer to the illustration below.

INSTALL BRACKET

Drywall application: After properly positioning the anti-tip

bracket, mark holes, then use a Phillips screwdriver or a low rpm power drill to drive the wall anchor into the surface of the wallboard until ush. Pre-drill holes if needed. For hard

wallboard or double-board construction, use a

For solid plaster, use a

/16" drill bit. Refer to the illustration

/4" drill bit.

below. Use #8 screws and at washers to fasten the bracket to the wall.

Wood oor application: After properly positioning the anti-

tip bracket, drill

/16" (5) pilot holes through the oor. Use #12 screws and at washers to secure the bracket to the oor.

Concrete oor application: After properly positioning the

anti-tip bracket drill

imum of 1

/2" (38) deep. Use 3/8" wedge anchors to secure

/8" (10) holes into the concrete a min-

the bracket to the oor.

ANTI-TIP BOLT ADJUSTMENT

Once the bracket is secure, adjust the anti-tip bolt so the

top of the washer is

/8" (22) maximum from the oor. Slide the range into the opening and verify the anti-tip bolt is engaged. Refer to the illustrations below.

ANTI-TIP

DEVICE

ENGAGED

Anti-tip bolt adjustment

Anti-tip bolt engaged

ANTI-TIP

BRACKET

3" (76)

Anti-tip bracket location

WALL

ANCHOR

ANTI-TIP

BRACKET

Wall anchor installation

wolfappliance.com | 9

INSTALLATION

Gas Supply Connection

All connections to the gas piping must be wrench-tightened. Do not overtighten or allow pipes to turn when tightening.

If a exible metal connector is being used, verify it is not kinked, then attach the gas supply line to the regulator on the range. Open the valve and check for leaks by placing a liquid detergent solution onto all gas connections. Bubbles around connections indicate a gas leak. If a leak appears, close the shut-off valve and adjust connections.

Troubleshooting

IMPORTANT NOTE: If the range does not operate properly,

follow these troubleshooting steps:

• Verify electrical power is supplied to the range.

• Verify the gas supply shut-off valve is in the open

position.

• If the range does not operate properly, contact Wolf

Factory Certied Service. Do not attempt to repair the range. Wolf is not responsible for service required to correct a faulty installation.

10 | Wolf Customer Care 800.222.7820

+ 22 hidden pages