INTERIOR VENTILATOR KITS
For use with hood models:
PW302418 PW362418 PW422418 PW482418 PW542418 PW602418 PW662418
PW302718 PW362718 PW422718 PW482718 PW542718 PW602718 PW662718
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If
you have questions, contact the manufacturer or your distributor.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the heating equipment manufacturer’s guidelines and safety standards such as those published
by the National Fire Protection Association (NFPA), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with an additional speed control device.
8. To reduce the risk of fire, use only steel ductwork.
9. This unit must be grounded.
WARNING
TO REDUCE THE RISK OF A COOKTOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
2. Always turn hood ON when cooking at high heat or when cooking flaming foods.
3. Clean ventilating fans frequently. Grease should not be allowed
to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the
size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A COOKTOP GREASE FIRE, OBSERVE THE FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out immediately, EVACUATE
AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you
already know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
CAUTION
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.
3. Your ventilator motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The motor will
restart when it cools down. If the motor continues to shut off and
restart, have the hood serviced.
4. Please read specification label on product for further information
and requirements.
DUAL BLOWER INSTALLATION
SINGLE BLOWER INSTALLATION
For blower models 814422 & 814423
PANEL, BACK
POWER
CORD
(8) 10-24 NUTS
1. Mount blowers to PANEL, BACK with (8) 10-24 NUTS
(provided).
2. Plug blower POWER CORD into the receptacle inside the
hood. Route wires away from the blower's moving parts. Bundle
wires with wire tie (provided).
For blower models 814419, 814420 & 814421
MOUNTING PLATE
CENTER
PIECE
(4) 10-24 NUTS
1. Mount blower to MOUNTING PLATE (provided with blower)
with (4) 10-24 NUTS (provided).
2. Remove CENTER PIECE of PANEL, BACK.
3. Mount blower / mounting plate assembly to PANEL, BACK
using (4) 10-24 NUTS (provided).
4. Plug blower POWER CORD into receptacle inside of hood.
Route wires away from the blower's moving parts. Bundle
wires with wire tie (provided).
(4) 10-24 NUTS
PANEL, BACK
POWER
CORD
99044553B
822076A