Each of trad emarks herein is registere d. The name of this produc t and other trademark s mentioned in this manual are the registered
trademark of their respective company.
Restriction
Copyright of this document is reserved. Und er no circumstances, this document shall be repro duced, distributed or changed, par tially
or wholly, without formal authorization.
Disclaimer
Hanwha Techwin
guarantee shall b e provided. Use of this docum ent and the subsequent results shall be entirely o n the user’s own responsibility.
Hanwha Techwin
Design and specications are subject to change without prior notice.
Co., Ltd. All r ights reser ved.
makes the bes t to verify the integrit y and correctness of the contents in this document, but no fo rmal
reserves t he right to change the contents of this document without prior notice.
Page 3
overview
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents
as they may deform or cause damage to the product.)
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.
● OVERVIEW
English _3
Page 4
overview
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION
: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within
this unit.
This exclamation point symbol is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING
• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or
damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat
generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water
on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately
disconnect the power source and contact the service center. Continued use in such a condition may cause
fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this
product in any way. (Hanwha Techwin is not liable for problems caused by unauthorized modifications or
attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric
shock.
4_ overview
Page 5
CAUTION
1. Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to
excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature, low temperature, or high humidity. Doing so may
cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall
it.
4. Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may cause fire or
damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the
CMOS image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.
10. Do not expose the camera to radioactivity. Radioactivity exposure may damage the CMOS.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus
● OVERVIEW
English _5
Page 6
overview
CONTENTS
OVERVIEW
3
INSTALLATION
8
APPENDIX
11
3 Important Safety Instructions
4 Safety Precautions
6 Contents
7 Product Features
8 Part Names and Functions
9 Precautions
9 Installing the camera
10 Protection of Cable from Water
10 Connecting the DVR
Use the 4K-pixel CMOS, and provide high resolution equivalent to 1200TVL horizontal resolution.
• High sensitivity
The built-in high sensitive COLOR CMOS can produce a clear image. 0Lux (Auto IR LED On)
• D-WDR (Digit Wide Dynamic Range)
With the 4K-pixel CMOS sensor, this camera can provide a clear and quality image even under the
circumstance of backlight, by way of and accurate exposure for the dark area and reducing exposure for the
bright area: resulting in a clear, detailed and accurate image.
● OVERVIEW
English _7
Page 8
installation
PART NAMES AND FUNCTIONS
a
b
NameDescription
c
d
Lens
a
Illumination Sensor
b
Power Cable
c
BNC Cable
d
4mm focal length enables you to monitor at a wider field of view
Detects incoming light to control the IR LED.
Use to power the camera.
BNC terminal for video signal output.
8_ installation
Page 9
PRECAUTIONS
Ensure you read out the following instructions before installing the camera:
• Select an area (ceiling or wall) that can withstand 5 times the camera weight
• Stuck-in or peeled-off cables can cause damage to the product or a fire.
• For safety purposes, keep anyone else away from the installation site.
And put aside personal belongings from the site, just in case.
INSTALLING THE CAMERA
The camera can be installed on the wall, ceiling, shelf or a desired position using the provided mounting bracket.
1. Choose an installation site that can sufficiently support the weight of the camera to be installed.
2. Adhere the installation template onto the ceiling and use it as installation locating tool.
CAMERA FRONT
3. Attach the camera mount to the wall using the supplied screws.
4. Adjust the direction of the camera to the desired direction, and tighten the bracket.
5. Adjust camera angle as needed.
● INSTALLATION
6. Connect the camera cable to the camera.
Take caution when installing the camera outdoors because the cable connectors may be wet with
moisture or pile up with impurities.
Although the camera is IP66 rated, direct exposure to water or moisture may cause problem such as
condensation.
English _9
Page 10
installation
PROTECTION OF CABLE FROM WATER
If this product is mounted outdoor, water leakage may occur at gap between cables. As shown below, butyl rubber
(available on the market) shall be used to protect from water.
1. Connect power supply and BNC power source.
2. Cover black sheath of the cable (Zone A), and ensure half of butyl rubber can cover the cable joint.
` Poor water protection at the cable sheath may cause water leakage. Make sure to wrap tightly.
J
` The water-proof butyl rubber is made of rubber that expands to twice the original length.` If you do not use cable joint, it must be covered with water-proof tape.
CONNECTING THE DVR
Connect the BNC connector of the camera to the enclosed 60ft camera cable, and then connect the BNC
connector of the camera cable to the BNC Video Input port of the DVR.
12V
VGA
LAN
HDMI
CAUTION
RISK OF ELECTRI SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK
DO NOT OPEN COVERS. NO USER SERVICEABLE
VIDEO INPUT
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING : TO PREVENT FIRE OR SHOCK HAZARD. DO NOT
EXPOSE UNITS NOT SPECIFICALLY DESIGNED
FOR OUTDOOR USE TO RAIN OR MOISTURE.
-30°C ~ +50°C (-22°F ~ +122°F) / Less than 90% RH
Startup : -10°C ~ +50°C
12V x 0.14A = 1.68W (IR off)
12V x 0.29A = 3.48W (IR on)
● APPENDIX
English _11
Page 12
appendix
PRODUCT OVERVIEW
unit : mm(inch)
12_ appendix
Page 13
TROUBLESHOOTING
Please refer to the following table if you have problems during camera operation.
Please contact with the authorized technicians if your problem cannot be solved through the guidance.
ProblemTroubleshooting
There is no content displayed on
the screen.
The image on the screen is dim.
The image on the screen is dark.
The camera fails to work normally and the surface is
hot.
The color is incorrect.
The screen flickers constantly.
When the coaxial communication is not available
● APPENDIX
y Check whether the power cable and the cable between camera and
monitor are connected correctly.
y Check whether BNC cable is connected to the camera correctly.y Check if video system is the same as of DVR.
y Whether the lens is stained with dust. Clean the lens with soft and
clean cloth.
y Set suitable condition for the monitor or DVR.y If the camera is pointed to the strong light, please change the position
of camera.
y Adjust the contrast ratio of monitor or DVR.y If there is intermediate equipment, please set 75Ω/Hi-z correctly.
y Please check whether the camera is connected to suitable power
supply correctly.
y Please check the setting of white balance setting menu.
y Please ensure that the camera is not pointed to the sun.
y Please ensure that the camera and monitor are installed in the
recommended distance.
y If they exceed the recommended installation distance, please use
coaxial and equivalent video amplifier.
English _13
Page 14
Any changes or modifications in construction of this device which are not expressly approved by the
party responsible for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Hanwha Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide
customers with more environmentally friendly products.
The Eco mark represents Hanwha Techwin's devotion to creating environmentally friendly products, and indicates
that the product satisfies the EU RoHS Directive.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate
these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This
product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other
household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains
mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these
substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them
through your local, free battery return system.
Page 15
Head Oce
6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si,
Gyeonggi-do, 463-400 Rep. of KOREA
Tel : +82.1588.5772 Fax : +82.31.8018.3740
www.wisenetlife.com
Hanwha Techwin America
500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666
Tel +1.844 WISENET (844.947.3638)
E-mail : cs@wisenetlife.com
www.wisenetlife.com
Hanwha Techwin Europe
Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom
Tel : 00800.8010.8022 / +31.(0)13.5792.790
www.wisenetlife.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.