Whirlpool WOD51EC0HW, WOS51EC7HW, WOS51EC0HW, WOD51EC7HW Installation Manual

INSTALLATION INSTRUCTIONS 27" (68.6 CM)

AND 30" (76.2 CM) ELECTRIC SINGLE

AND DOUBLE BUILT-IN OVEN

INSTRUCTIONS D’INSTALLATION FOUR

ÉLECTRIQUE ENCASTRÉ 27" (68,6 CM)

ET 30" (76,2 CM) - SIMPLE ET DOUBLE

INSTRUCCIONES DE INSTALACIÓN DEL

HORNO EMPOTRADO ELÉCTRICO SIMPLE

Y DOBLE DE 27" (68,6 CM) Y 30" (76,2 CM)

Table of Contents/Table des matières/Índice

BUILT-IN OVEN SAFETY ......................... 2

INSTALLATION REQUIREMENTS

Tools and Parts Location Requirements Electrical Requirements

INSTALLATION INSTRUCTIONS

Prepare Built-In Oven Remove Oven Door(s) Replace Oven Door(s) Positioning Oven Feet for Multiple

Cabinet Cutout Heights ........................ 8

Make Electrical Connection Install Oven Install Warming Drawer Deﬂector Kit .. 16 Complete Installation

...................................... 2

......................... 3

........................ 6

............................ 7

........................... 7

........................... 8

.......................................... 14

.......................... 16

.......... 2

............ 7

................ 13

SÉCURITÉ DU FOUR ENCASTRÉ EXIGENCES D’INSTALLATION

Outillage et pièces Exigences d’emplacement Spéciﬁcations électriques

INSTRUCTIONS D’INSTALLATION

Préparation du four encastré Dépose de la/des porte(s) du four Réinstallation la porte(s) du four Positionnement des pieds du four

pour des ouvertures d’encastrement

de hauteur différente ........................... 24

Raccordement électrique Installation du four Installation de l’ensemble de

déﬂecteur du tiroir-réchaud ................31

Achever l’installation

............................... 17

.................... 28

............................... 30

........................... 32

....... 17

............ 17

.................. 18

................... 21

...... 22

.............. 22

...... 22

......... 23

SEGURIDAD DEL

HORNO INTEGRADO ............................ 33

REQUISITOS DE INSTALACIÓN

Herramientas y piezas Requisitos de ubicación Requisitos eléctricos

INSTRUCCIONES DE INSTALACIÓN

Prepare el horno integrado Retire la puerta del horno Vuelva a colocar la puerta del horno Ubicación de las patas del

horno para múltiples alturas

de corte del armario ............................ 39

Haga la conexión del

suministro eléctrico ............................. 44

Instale el horno Instale el kit de deﬂector

para cajón de calentamiento .............. 47

Finalización de la instalación

........................... 37

.................................... 45

.......... 33

......................... 33

...................... 34

.. 38

................. 38

.................... 38

.. 39

.............. 47

IMPORT

Save for local electrical inspector’s use.

IMPORTANT :

À conserver pour consultation par l’inspecteur local des installations électriques.

IMPORTANTE:

Guarde para tener a disposición del inspector de electricidad local.

W11129956

ANT:

BUILT-IN OVEN SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

follow instructions.

You

can be killed or seriously injured if you don't

instructions.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools Needed

■ Phillips screwdriver

■ Measuring tape

■ Hand or electric drill (for wall cabinet installations)

■ 1” (2.5 cm) drill bit (for wall cabinet installations)

■ Level

■ Flat-blade screwdriver

Parts Needed

■ UL Listed or CSA Approved conduit connector

■ UL Listed wire connectors

■ Warming Drawer Deﬂector Kit (for ovens installed above a

warming drawer):

Color Size Type Warming Drawer

Deﬂector Kit

White 27” Single / Double W10510613 White 30” Single / Double W10510614 Black 27” Single / Double W10531009 Black 30” Single / Double W10531010 SS 27” Single / Double W10536338 SS 30” Single / Double W10536339 BSS 27” Single / Double W10888988 BSS 30” Single / Double W10727416 Bronze 30” Single / Double W11123007

To order, see the “Assistance or Service” section of the Use and Care Guide.

■ Flush Installation Kit (for Single and Double installed at ﬂush

installation):

Color Size Type Flush Installation

Kit

White 27” Single / Double W11173681 White 30” Single / Double W11173683 Black 27” Single / Double W11173685 Black 30” Single / Double W11173691 SS 27” Single / Double W11173693 SS 30” Single / Double W11123003 BSS 27” Single / Double W11173700 BSS 30” Single / Double W11173703 Bronze 30” Single / Double W11123005

To order, see the “Assistance or Service” section of the Use and Care Guide.

Parts Supplied

■ #8-14 x 3/4” (19 mm) screws: single ovens (2), double ovens

(4)

■ #8-18 x 3/8” (9.5 mm) screws: bottom vent (2)

■ #8-18 x 1/4” (6.4 mm) screws: bottom vent trim (4)

■ #8-18 x 3/8” (9.5 mm) screws: double oven feet (4)

■ Bottom vent

■ Bottom vent trim

■ Rear feet: double oven (2)

■ Front feet: double oven (2)

Check local codes. Check existing electrical supply. See the “Electrical Requirements” section.

It is required that all electrical connections be made by a licensed, qualiﬁed electrical installer.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance with oven.

■ Recessed installation area must provide complete

enclosure around the recessed portion of the oven.

■ Grounded electrical supply is required. See the

“Electrical Requirements” section.

■ Electrical supply junction box should be located 3" (7.6 cm)

above the cutout or 3" (7.6 cm) maximum below the support surface when the oven is installed in a wall cabinet. A 1" (2.5 cm) minimum diameter hole should have been drilled in the right rear or left rear corner of the upper or lower support surface to pass the appliance cable through to the junction box.

NOTE: For undercounter installation, it is recommended that the junction box be located in the adjacent right or left cabinet. If you are installing the junction box on rear wall behind oven, it is recommended that the junction box be recessed and located in the upper center of the cabinet.

■ Oven support surface must be solid, level, and ﬂush

with bottom of cabinet cutout.

■ Floor must be able to support a single oven weight of 129 lbs

(59 kg) for 27" (68.6 cm) models or 154 lbs (70 kg) for 30" (76.2 cm) models.

■ Floor must be able to support a double oven weight of

251 lbs (114 kg) for 27" (68.6 cm) models or 288 lbs (131 kg) for 30" (76.2 cm) models.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate, or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).

Undercounter Installation (with Cooktop Installed Above):

Refer to the Cutout Dimensions for Ovens Installed Under Cooktop (separate sheet). See product website for list of cooktop models approved for use above select wall-oven models.

Product Dimensions — Single Ovens

27" (68.6 cm) models

A. 28

/4" (72.8 cm) max.

overall height

B. 25

/16" (64.6 cm) max.

recessed width

C. 26

/4" (67.9 cm)

recessed height

D. 23

/4" (59.1 cm) max.

recessed depth E. 27" (68.6 cm) overall width F. 12" (30.5 cm) from back

of control panel to start

of strain relief G. 48" (121.9 cm) ﬂexible

conduit length

30" (76.2 cm) models

A. 28

B. 28

C. 26

D. 23

E. 30" (76.2 cm) overall width F. 12" (30.5 cm) from back

G. 48" (121.9 cm) ﬂexible

/4" (72.8 cm) max.

overall height

/2" (72.4 cm) max.

recessed width

/4" (67.9 cm)

recessed height

/4" (59.1 cm) max.

recessed depth

of control panel to start of strain relief

conduit length

Cabinet Dimensions — Single Ovens

Single Oven Undercounter (Without Cooktop Installed Above)

Single Ovens Installed in Cabinet

27" (68.6 cm) models

A. 27" (68.6 cm) min.

cabinet width

B. 1

/2" (3.8 cm) min. top of cutout to underside of countertop

C. 5

/4" (13.3 cm) bottom of cutout to ﬂoor

D. 25

/2" (64.8 cm)

cutout width

E. 28" (71.2 cm) min.

cutout height

30" (76.2 cm) models

A. 30" (76.2 cm) min.

cabinet width

B. 1

/2" (3.8 cm) min. top of cutout to underside of countertop

C. 5

/4" (13.3 cm) bottom of cutout to ﬂoor

D. 28

/2" (72.4 cm)

cutout width

E. 28" (71.2 cm) min.

cutout height

27" (68.6 cm) models

A. 27" (68.6 cm) min.

cabinet width

B. 1" (2.5 cm) top of

cutout to bottom of upper cabinet door

C. 32" (81.3 cm) bottom

of cutout to ﬂoor

D. 25

/2" (64.8 cm)

cutout width

E. 1

/2" (3.8 cm) min. bottom of cutout to top of cabinet door

F. 28" (71.2 cm)*

recommended cutout height

G. 24" (60.7 cm) cutout

depth

30" (76.2 cm) models

A. 30" (76.2 cm) min.

cabinet width

B. 1" (2.5 cm) top of

cutout to bottom of upper cabinet door

C. 32" (81.3 cm) bottom of

cutout to ﬂoor

D. 28

/2" (72.4 cm)

cutout width

E. 1

/2" (3.8 cm) min. bottom of cutout to top of cabinet door

F. 28" (71.2 cm)*

recommended cutout height

G. 24" (60.7 cm) cutout

depth

*NOTE: The cutout height can be between 2615/16" and 297/16"

(68.4 cm and 74.8 cm) for single ovens.

Product Dimensions — Double Ovens Cabinet Dimensions — Double Ovens

Double Ovens Installed in Cabinet

27" (68.6 cm) models

A. 51

/16" (130.0 cm)

max. overall height

B. 25

/16" (64.6 cm)

max. recessed width

C. 48

/16" (124.0 cm)

recessed height

D. 23

/4" (59.1 cm) max.

recessed depth E. 27" (68.6 cm) overall width F. 12" (30.5 cm) from back

of control panel to start

of strain relief G. 66" (167.6 cm) ﬂexible

conduit length

30" (76.2 cm) models

A. 51

/16" (130.0 cm) max.

overall height

B. 28

/2" (72.4 cm) max.

recessed width

C. 48

/16" (124.0 cm)

recessed height

D. 23

/4" (59.1 cm) max.

recessed depth E. 30" (76.2 cm) overall width F. 12" (30.5 cm) from back

of control panel to start

of strain relief G. 66" (167.6 cm) ﬂexible

conduit length

27" (68.6 cm) models

A. 27" (68.6 cm) min.

cabinet width

B. 1" (2.5 cm) top of

cutout to bottom of upper cabinet door

C. 14

/4" (37.5 cm) bottom of cutout to ﬂoor is recommended. 4-143/4" (10.2-37.5 cm) bottom of cutout to ﬂoor is acceptable.

D. 25

/2" (64.8 cm) cutout width

E. 1

/2" (3.8 cm) min. bottom of cutout to top of cabinet door

F. 50

/4" (127.6 cm)*

recommended cutout height

G. 24" (60.7 cm) cutout depth

30" (76.2 cm) models

A. 30" (76.2 cm) min.

cabinet width

B. 1" (2.5 cm) top of

cutout to bottom of upper cabinet door

C. 14

/4" (37.5 cm) bottom of cutout to ﬂoor is recommended. 4-143/4" (10.2-37.5 cm) bottom of cutout to ﬂoor is acceptable.

D. 28

/2" (72.4 cm) cutout width

E. 1

/2" (3.8 cm) min. bottom of cutout to top of cabinet door

F. 50

/4" (127.6 cm)*

recommended cutout height

G. 24" (60.7 cm) cutout depth

*NOTE: The cutout height can be between 487/8" and 523/16"

(124.1 cm and 132.6 cm) for double ovens.

Electrical Requirements

A. Model/serial/rating plate

If codes permit and a separate ground wire is used, it is recommended that a qualiﬁed electrical installer determine that the ground path and the wire gauge are in accordance with local codes.

Check with a qualiﬁed electrical installer if you are not sure the oven is properly grounded.

This oven must be connected to a grounded metal, permanent wiring system.

Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70 — latest edition or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91 — latest edition, and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

Electrical Connection

To properly install your oven, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

■ Oven must be connected to the proper electrical voltage and

frequency as speciﬁed on the model/serial/rating plate. The model/serial/rating plate is located under the control panel on single ovens and under the control panel on the upper oven cavity on double ovens. See the following illustrations.

Single Oven

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

Double Oven

■ Models rated from 7.3 to 9.6 kW at 240 volts (6.3 to 8.3 kW

at 208 volts) require a separate 40-amp circuit. Models rated from 4.9 to 7.2 kW at 240 volts (4.3 to 6.2 kW at 208 volts) require a separate 30-amp circuit. Models rated at

4.8 kW and below at 240 volts (4.2 kW and below at 208 volts) require a separate 20-amp circuit.

■ A circuit breaker is recommended.

■ Connect directly to the circuit breaker box (or fused

disconnect) through ﬂexible, armored, or nonmetallic sheathed, copper cable (with grounding wire). See the “Make Electrical Connection” section.

■ Flexible conduit from the oven should be connected directly

to the junction box.

■ Fuse both sides of the line.

■ Do not cut the conduit. The length of conduit provided is for

serviceability of the oven.

■ A UL Listed or CSA Approved conduit connector must be

provided.

■ If the house has aluminum wiring, follow the procedure

below: Connect the aluminum wiring using special connectors

and/or tools designed and UL Listed for joining copper to aluminum.

Follow the electrical connector manufacturer’s recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

Series Voltage Frequency Rating

WOD97EC/ WODA7EC/ WOD77EC

WOS97EC/ WOSA2EC/ WOS72EC

120/240 V AC 60 Hz 8 kW 120/208 V AC 60 Hz 6 kW

120/240 V AC 60 Hz 4 kW 120/208 V AC 60 Hz 3 kW

WOD51EC 120/240 V AC 60 Hz 7.6 kW

120/208 V AC 60 Hz 5.7 kW

WOS51EC 120/240 V AC 60 Hz 3.9 kW

120/208 V AC 60 Hz 2.9 kW

INSTALLATION INSTRUCTIONS

Prepare Built-In Oven

1. Decide on the ﬁnal location for the oven. Avoid drilling

or cutting into house wiring during installation.

WARNING

Excessive Weight Hazard

Use two or more people to move and install oven.

Failure to do so can result in back or other injury.

2. To avoid ﬂoor damage, set the oven onto cardboard prior

to installation. Do not use handle or any portion of the front frame for lifting.

3. Remove the shipping materials and tape from the oven.

Remember to keep the corner posts and other materials that may be needed for installation.

4. Remove the hardware package from inside the bag

containing literature.

5. Remove and set aside racks and other parts from

inside the oven.

6. Move oven and cardboard close to the oven’s ﬁnal location.

Remove Oven Door(s)

IMPORTANT: Use two hands to remove oven door. For double ovens, repeat the process for each door.

1. Prior to removing the oven door, prepare a surface where

you will place it. This surface should be ﬂat and covered with a soft blanket, or use the corner posts from your packaging material.

2. Fully open the oven door.

4. Gently start to close the door. The door will stop at a partially

closed position.

5. Using two hands, grasp the edges of the oven door. Close

the oven door slightly past the stop position to take the weight off of the door hinges, and then pull the oven door up.

6. Pull the oven door toward you, and then remove. You may

need to gently shift the door from side to side as you pull.

Door hinges

3. Locate the oven door hinge locks in both corners of the

oven door, and rotate the hinge locks toward the oven door to the unlocked position. If the door hinge lock is not rotated fully (see illustration B), the door will not remove properly.

Locked position

Grip here to rotate.

A. Oven door hinge lock in

locked position

Unlocked position

Soft close hinge

arm on select models

B. Oven door hinge lock in

partially unlocked position

7. Set the oven door aside on the prepared covered work

surface with the oven door resting on its handle.

8. To continue with the oven installation, go to the

“Positioning Oven Feet for Multiple Cabinet Cutout Heights” section.

Replace Oven Door(s)

1. Using two hands, grasp side edges of door at the midpoint.

Face the oven cavity.

2. Locate the slots on each side of the oven front frame for

the door hinge locks.

A. Slot in the oven cavity for door hinge lock

3. Using two hands, grasp the edges of the oven door. At a 45°

angle, insert the hinges at the same time, and push the oven door into the oven cavity slot to replace. You may need to gently shift the door from side to side as you push.

5. Lower the oven door to the fully open position. If the oven

door does not open to a full 90°, repeat steps 1 through 3.

6. Locate the oven door hinge locks in the corners of the oven

door, and rotate the hinge locks toward the oven cavity to the locked position.

Unlocked position

7. After the door hinges have been locked, gently swing the

door upward to close. The door should not be forced closed.

8. When the hinges are properly installed and the door is

closed, there should be an even gap between the door and the control panel. If one side of the oven door is lower than the other, the hinge on that side is not properly installed.

See the “Remove Oven Door(s)” and “Replace Oven Door(s)” sections.

Locked position

Soft close hinge

arm on select models

Positioning Oven Feet for Multiple

Cabinet Cutout Heights

4. Make sure the door hinge notch is engaged on the bottom

of the oven cavity slot.

IMPORTANT: Do not close the door at this step or damage may occur to the door hinge.

Single Ovens

The positioning of the oven feet allow a single oven to be installed in a cutout height between 26 (68.4 cm and 74.8 cm). Refer to the following instructions to position the feet for the size of your cabinet cutout.

/16" and 297/16"

Cutout Height Is Between 275/8" and 285/8" (70.2 cm and 72.7 cm)

The oven feet do not need to be changed. They are positioned correctly as received.

Go to the “Make Electrical Connection” section.

Cutout Height Is Between 2615/16" and 2711/16" (68.4 cm and 70.3 cm)

1. Using two or more people, place the oven on its back

on a covered surface.

Cutout Height Is Between 2811/16" and 297/16" (72.8 cm and 74.8 cm)

1. Using two or more people, place the oven on its back

on a covered surface.

2. Remove the foot from the right front spacer by removing

the #8-18 x 3/8" (9.5 mm) screw. NOTE: Do not remove the spacer.

A. Spacer B. Foot C. #8-18 x 3/8" (9.5 mm) screw

3. In the same manner, remove the feet on the right rear,

left front, and left rear of the oven.

4. Using two or more people, place the oven in its upright

position.

2. Remove the foot from the right front spacer by removing

the #8-18 x 3/8" (9.5 mm) screw. NOTE: Do not remove the spacer.

A. Spacer B. Foot C. #8-18 x 3/8" (9.5 mm) screw

3. Rotate the foot 90°, so the short side of the foot

is positioned toward the top of the oven.

5. Go to the “Make Electrical Connection” section.

4. Reinstall the foot to the spacer using the #8-18 x 3/8"

(9.5 mm) screw previously removed.

5. In the same manner, remove, rotate, and reinstall the

feet on the right rear, left front, and left rear of the oven.

6. Using two or more people, place the oven in its upright

position.

7. Go to the “Make Electrical Connection” section.

Double Ovens

The positioning of the oven feet allow a double oven to be installed in a cutout height between 487/8" and 523/16" (124.1 cm and 132.6 cm). Refer to the following instructions to position the feet for the size of your cabinet cutout.

Cutout Height Is Between 487/8" and 507/16" (124.1 cm and 128.1 cm)

The oven feet do not need to be installed. The oven is conﬁgured correctly as received.

NOTE: Do not remove the spacers. Go to the “Make Electrical Connection” section.

A. Spacers

Cutout Height Is Between 501/2" and 511/8"

(128.2 cm and 129.9 cm)

1. Using two or more people, place the oven on its back

on a covered surface.

4. Install a front foot on the left front spacer using a #8-18 x

3/8" (9.5 mm) screw. NOTE: Position the foot so the long side of the foot is facing

toward the inside of the oven.

2. Install a foot on the left rear spacer using a #8-18 x 3/8"

(9.5 mm) screw. NOTE: Position the foot so the long side of the foot is facing

toward the top of the oven.

A. Spacer B. Foot C. #8-18 x 3/8" (9.5 mm) screw

3. In the same manner, install a foot on the right rear of the oven.

A. Front foot B. #8-18 x 3/8" (9.5 mm) screw C. Spacer

5. In the same manner, install a front foot on the right front

of the oven.

6. Using two or more people, place the oven in its upright

position.

7. Go to the “Make Electrical Connection” section.

Cutout Height Is Between 513/16" and 523/16"

(130 cm and 132.6 cm)

1. Using two or more people, place the oven on its back

on a covered surface.

2. Install a foot on the left rear spacer using a #8-18 x 3/8"

(9.5 mm) screw. NOTE: Position the foot so the short side of the foot is facing

toward the top of the oven.

4. Install a front foot on the left front using a #8-18 x 3/8"

(9.5 mm) screw. NOTE: Position the foot so the long side of the foot is facing

toward the top of the oven.

A. Front foot B. #8-18 x 3/8" (9.5 mm) screw C. Spacer

A. Spacer B. Foot C. #8-18 x 3/8" (9.5 mm) screw

3. In the same manner, install a foot on the right rear of the oven.

5. In the same manner, install a front foot on the right front

of the oven.

6. Using two or more people, place the oven in its upright

position.

7. Go to the “Make Electrical Connection” section.

Make Electrical Connection

(1.3 cm)

For Double Ovens For Single Ovens

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge copper wire.

Electrically ground oven.

Failure to follow these instructions can result in death, fire, or electrical shock.

This oven is manufactured with a neutral (white) power supply wire and a cabinet-connected green (or bare) ground wire twisted together.

1. Disconnect power.

2. Feed the ﬂexible conduit from the oven through

the opening in the cabinet.

3. Remove junction box cover if it is present.

4. Install a UL Listed or CSA Approved conduit connector

to the junction box.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use 12 gauge copper wire.

Electrically ground oven.

Failure to follow these instructions can result in death, fire, or electrical shock.

4-Wire Cable from Home Power Supply

IMPORTANT: Use the 4-wire cable from home power

supply in the U.S. where local codes do not allow grounding through neutral, New Branch circuit installations (1996 NEC), mobile homes and recreational vehicles, new construction, and in Canada.

A. UL Listed or CSA Approved conduit connector

5. Route the ﬂexible conduit from the oven to the junction box

through a UL Listed or CSA Approved conduit connector.

6. Tighten screws on conduit connector.

7. See the “Electrical Connection Options Chart” to complete

installation for your type of electrical connection.

Electrical Connection Options Chart

If your home has: Go to section:

4-wire 4-Wire Cable from Home

½"

3-wire 3-Wire Cable from Home

½"

Power Supply

A. Cable from home power supply B. Black wires C. Red wires D. 4-wire ﬂexible conduit

from oven

E. Junction box

1. Connect the two black wires (B) together using

a UL Listed wire connector.

2. Connect the two red wires (C) together using

a UL Listed wire connector.

3. Untwist white wire from green (or bare)

ground wire coming from the oven.

4. Connect the two white wires (F) together using

a UL Listed wire connector.

5. Connect the green (or bare) ground wire (H) from

the oven cable to the green (or bare) ground wire (in the junction box) using a UL Listed wire connector.

6. Install junction box cover.

F. White wires G. UL Listed wire connectors H. Green (or bare) ground wires I. UL Listed or CSA Approved

conduit connector

3-Wire Cable from Home Power Supply: U.S. Only

IMPORTANT: Use the 3-wire cable from home power supply where local codes permit a 3-wire connection.

2. Push against the seal area of the front frame to push

the oven into the cabinet until the back surface of the front frame touches the front wall of the cabinet.

A. Cable from home power supply B. Junction box C. Black wires D. White wires E. Green (or bare) ground

wire (from oven)

F. 4-wire ﬂexible conduit

from oven G. Red wires H. UL Listed wire connectors I. UL Listed or CSA Approved

conduit connector

1. Connect the two black wires (C) together using

a UL Listed wire connector.

2. Connect the two white wires (D) and the green (or bare)

ground wire (of the oven cable) using a UL Listed wire connector.

3. Connect the two red wires (G) together using

a UL Listed wire connector.

4. Install junction box cover.

Install Oven

1. Using two or more people, lift the oven partially into the

cabinet cutout. Use the oven opening as an area to grip. NOTE: Push against seal area of the oven front frame when

pushing the oven into the cabinet. Do not push against the outside edges.

3. Push oven completely into the cabinet and center

the oven into the cabinet cutout.

4. Remove the tape from the black front trim, and remove

the zip tie from the mounting spacer.

■ Securely fasten the oven to the cabinet using the

#8-14 x 1" (2.5 cm) screws provided.

■ Insert the screws through holes in black trim, aligning

with the holes in oven frame and mounting spacers already in place. Do not overtighten screws.

C D

A. Oven frame B. Mounting spacer C. Oven frame hole D. Black trim piece

5. The bottom vent and bottom vent trim (required when

the oven is installed with the feet in the tall position) are shipped in the foam packing at the top of the oven.

To install only the bottom vent, see the following instructions. To install both the bottom vent and the bottom vent trim for installations with the feet in the tall position, see the instructions in Step 6.

■ Align vent tab (B) with oven frame (A) as shown.

■ Using one #8-18 x 3/8" (9.5 mm) screw (D) on each side

of the vent tab (B), fasten the vent securely to the oven.

■ Align vent tab (B) with oven frame (A) as shown.

■ Using one #8-18 x 3/8" (9.5 mm) screw (E) on each side

of the vent tab (B), fasten the vent securely to the oven.

A. Oven frame B. Vent tab

C. Oven vent D. #8-18 x 3/8"

(9.5 mm) screws

6. On models with the feet installed in the tall position, the

bottom vent trim must also be installed. See the following instructions to install.

■ Flex the upper vent piece (C) away from the lower vent

piece (D) to slide the bottom vent trim (B) between them. Some force may be required to ﬂex the upper vent trim (C) away from the lower vent trim (D). Some force may also be required to ﬂex the bottom vent trim (B) and slide it into position. Make sure screw holes are properly aligned between the two pieces. See the following illustration.

■ Install the bottom vent trim (B) to the lower vent piece (D)

using two #8-18 x 1/4" (6.4 mm) screws on each side.

A. Oven frame B. Vent tab C. Oven vent

D. Bottom vent trim E. #8-18 x 3/8"

(9.5 mm) screw

7. Replace the oven racks.

8. Replace the oven door. See the “Replace Oven

Door(s)” section.

9. Check that the door is free to open and close. If it is not,

repeat the removal and installation procedures. See the “Prepare Built-In Oven” section.

10. Repeat for lower oven door.

11. Reconnect power.

12. The display panel will light brieﬂy, and “PF” should

appear in the display.

13. If the display panel does not light, reference the

“Warranty” section of the Use and Care Guide.

A. #8-18 x 1/4"

(6.4 mm) screw

B. Bottom vent trim

C. Upper vent piece D. Lower vent piece

+ 33 hidden pages