Whirlpool WFC8090GX0 Owner’s Manual

Use and Care Guide and Installation Instructions

Guide d’utilisation et d’entretien et Instructions d’installation

Smart All-In-One Washer and Dryer

Laveuse et sécheuse intelligente combinées

Para obtener acceso al Manual de uso y

cuidado en español, o para obtener información adicional acerca de su producto, visite: www.whirlpool.com

If you have any problems or questions, visit us at www.whirlpool.com. Pour tout problème ou toute question, consulter www.whirlpool.ca.

Connect your Smart All-In-One Washer and Dryer with your mobile device at www.whirlpool.com/connect (in Canada, www.whirlpool.ca/en_ca.html)

Connecter votre laveuse et sécheuse intelligente combinées avec votre appareil mobile à www.whirlpool.ca/fr_ca.html)

Designed to use only HE High Efficiency detergents.

Conçue pour l’utilisation

d’un détergent haute W11114293A efficacité seulement.

W11132621A–SP

Table of Contents
ALL-IN-ONE WASHER/DRYER SAFETY...............................		2
ACCESSORIES.......................................................................		4
OPERATING INSTRUCTIONS................................................		5
Control Panel and Features.............................................		5
Cycle Guides....................................................................		6
Choosing the Right Detergent..........................................		9
Using the Load & Go™ Bulk Dispenser.............................		9
Using the All-In-One Washer/Dryer.................................		10
All-In-One Washer/Dryer Maintenance...........................		15
INSTALLATION INSTRUCTIONS.........................................		19
Installation Requirements...............................................		19
Location Requirements..................................................		20
Drain System..................................................................		22
Unpacking Washer/Dryer................................................		23
Electrical Requirements – U.S.A Only.............................		24
Electrical Requirements – Canada Only..........................		25
Electrical Installation – U.S.A. Only.................................		25
Route Drain Hose............................................................		29
Connect Inlet Hose.........................................................		29
Level Washer/Dryer.........................................................		30
Plug in Washer/Dryer......................................................		31
Complete Installation Checklist......................................		32
Internet Connectivity Guide............................................		32
TROUBLESHOOTING............................................................		33
Manually Unlocking the Door..........................................		44
CONNECTED APPLIANCE REGULATORY NOTICES.........		45
WARRANTY...........................................................................		47
ASSISTANCE OR SERVICE...................................	Back Cover

Table des matières
SÉCURITÉ DE LA LAVEUSE/SÉCHEUSE...........................		48
ACCESSOIRES.....................................................................		50
INSTRUCTIONS D'UTILISATION.........................................		51
Tableau de commande et caractéristiques....................		51
Guide des programmes.................................................		52
Choix du détergent approprié.........................................		55
Utilisation du distributeur Load & Go™............................		55
Utilisation de la laveuse/sécheuse combinée.................		56
Entretien de la laveuse/sécheuse combinée...................		61
INSTRUCTIONS D’INSTALLATION......................................		65
Exigences d’installation.................................................		65
Exigences d’emplacement.............................................		66
Système de vidange......................................................		68
Déballage de la laveuse/sécheuse.................................		69
Spécifications électriques...............................................		70
Acheminer le tuyau de vidange.......................................		71
Raccorder le tuyau d’arrivée...........................................		71
Réglage de l’aplomb de la laveuse/sécheuse................		72
Brancher la laveuse/sécheuse........................................		73
Liste de vérification pour installation terminée...............		74
Guide de connexion Internet...........................................		74
DÉPANNAGE..........................................................................		75
Déverrouillage manuel de la porte..................................		87
AVIS D’APPLICATION DE LA RÉGLEMENTATION
DE LA CONNEXION DES ÉLECTROMÉNAGERS...............		88
GARANTIE..............................................................................		90
ASSISTANCE OU SERVICE......................	Couverture arrière

ALL-IN-ONE WASHER/DRYER SAFETY

2

3

ACCESSORIES

INSTALLATION & MAINTENANCE

ACCESSORIES

FACTORY CERTIFIED PARTS – these three words represent quality parts and accessories designed specifically for your appliance.

Time tested engineering that meets our strict quality specifications.

FACTORY CERTIFIED PARTS

Accessories designed for your appliance:

Customize your new washer/dryer with the following genuine Whirlpool accessory. For more information on options and ordering, call 1-866-698-2538 or visit us at: www.whirlpool.com. In Canada, call 1-800-688-2002 or visit us at www.whirlpool.ca.

12" Pedestal

Color-matched pedestal raises the washer/dryer to a more comfortable working height.

4

OPERATING INSTRUCTIONS

Control Panel and Features

2

5

4:28

3:15

What to Wash How to Wash

REGULAR NORMAL

Temperature		Spin Speed		Auto Dry
WARM		EXTRA FAST		Dry

1	3			6	7
		4

1POWER BUTTON

Touch to power up the washer/dryer.

2HOME BUTTON

Touch this button and the LCD screen will show the home screen, where you can select your cycle, settings, and options.

3FAVORITES BUTTON

Stores and accesses your favorite cycles.

4LCD SCREEN

Use this screen to select cycle, settings, options, etc.

5REMOTE ENABLE BUTTON

Touch this button to be able to use the Whirlpool™ app

to control the washer/dryer. Download the Whirlpool™ app and follow the instructions to connect your washer/dryer to your home Wi-Fi network. You may also visit www.whirlpool.com/connect. In Canada, visit www.whirlpool.ca/en_ca.html and click on the Whirlpool® Connected Appliances link.

6TOOLS BUTTON

Touch this button to access the tools screen. For more information, see page 13.

7START/PAUSE BUTTON

Touch to start, or touch to pause a cycle. When you start a cycle, the door will lock, the washer/dryer will sense the load size, and the wash or dry cycle will begin.

Load & Go™ Bulk Dispenser

The Load & Go™ bulk dispenser holds up to 33.8 oz. (1000 mL) of liquid HE detergent (Dispenser 1) and 16.9 oz. (500 mL) of liquid fabric softener or liquid HE detergent (Dispenser 2), enough for multiple loads of laundry. It adds the appropriate quantity of HE detergent and liquid fabric softener to the wash load at the proper time. See “Using the Load & Go™ Bulk Dispenser” for information on using the dispenser.

B

A

ADispenser 1

This dispenser holds 33.8 oz (1000 mL) of liquid HE detergent for your main wash cycle, and automatically dispenses liquid detergent at the optimum time in the cycle.

BDispenser 2

This dispenser holds 16.9 oz (500 mL) of liquid fabric softener. It automatically dispenses liquid fabric softener at the optimum time in the cycle. This dispenser may

instead be used as a second liquid HE detergent dispenser. See Step 11 on page 13 for information.

IMPORTANT: Do not use chlorine bleach in this washer/dryer, and do not use powdered detergent in the Load & Go™ bulk dispenser. Powdered detergent must be added to the drum prior to adding laundry. See “Using the All-In-One Washer/Dryer.”

5

Cycle Guides

You can use this washer/dryer to wash only, dry only, or wash and dry. This washer/dryer has a unique user interface to help you select the best wash cycle for your load. The “What to Wash/How to Wash” layout guides you to the optimal cycle in two easy steps:

First determine what items are in the load that you are trying to wash. Use that to guide your “What to Wash” selection. Then determine how you want the washer to wash them and select the appropriate “How to Wash” selection. Selecting “What to Wash” will automatically select a default “How to Wash selection,” so selecting a “How to Wash” is optional. See chart below for more details.

	“What to Wash”
What Items Do You Want to Wash?	Cycle Selection:
Cottons, linens, and mixed garment loads	Regular
Bright or darkly colored cottons, linens, and mixed loads	Colors
No-iron fabrics, dress shirts/pants, synthetics, sheer/lacy garments	Delicates
White fabrics/garments	Whites
Sturdy towels and washcloths	Towels
Large items such as small comforters, sleeping bags, jackets, and washable rugs	Bulky Items
	“How to Wash”
How Do You Want to Wash Them?	Cycle Selection:
Regular/normal	Normal
Fast	Quick
Gentle cleaning with cold water	Cold Wash
Powerful cleaning	Heavy Duty
Kill 99% of three common household bacteria	Sanitize

Settings and options shown in bold are default settings for that wash cycle. For best fabric care, choose the cycle, options, and settings that best fit the load being washed. Always read and follow fabric care labels and laundry product instructions. Avoid tightly packing the washer/dryer. The washer/dryer will not rinse well or spin correctly if tightly packed. Loading the drum half full or less will improve washing and drying performance and cycle time. Not all settings are available with each cycle, and some options cannot be used together.

What	How	Basic Settings					Additional Options
		Temperature	Spin Speed	Dry Mode	Set Soil Level	Rinses		Pre-Soak	Tumble Fresh™	Wrinkle Shield™
Regular	Normal	Extra Hot	Extra Fast	Auto	Light	2		X	X	X
		Hot	Fast	Timed	Normal	3
		Warm	Medium		Heavy	4
		Cool				5
		Cold
	Quick	Extra Hot	Extra Fast	Auto	Light	2		X	X	X
		Hot	Fast	Timed	Normal	3
		Warm	Medium		Heavy
		Cool	Slow
		Cold	Off
	Cold Wash	Cool	Extra Fast	Auto	Light	2		X	X	X
		Cold	Fast	Timed	Normal	3
			Medium		Heavy	4
			Slow			5
			Off
	Heavy Duty	Extra Hot	Extra Fast	Auto	Light	2		X	X	X
		Hot	Fast	Timed	Normal	3
		Warm	Medium		Heavy	4
		Cool	Slow			5
		Cold	Off
	Sanitize	Extra Hot	Extra Fast	Auto	Light	2			X	X
			Fast	Timed	Normal	3
			Medium		Heavy	4
						5

6

What	How	Basic Settings					Additional Options
		Temperature	Spin Speed	Dry Mode	Set Soil Level	Rinses		Pre-Soak	Tumble Fresh™	Wrinkle Shield™
Colors	Normal	Warm	Extra Fast	Auto	Light	2		X	X	X
		Cool	Fast	Timed	Normal	3
		Cold	Medium		Heavy	4
			Slow			5
			Off
	Quick	Warm	Extra Fast	Auto	Light	2		X	X	X
		Cool	Fast	Timed	Normal	3
		Cold	Medium		Heavy
			Slow
			Off
	Cold Wash	Cool	Extra Fast	Auto	Light	2		X	X	X
		Cold	Fast	Timed	Normal	3
			Medium		Heavy	4
			Slow			5
			Off
Delicates	Normal	Warm	Medium	Auto	Light	2		X	X	X
		Cool	Slow	Timed	Normal	3
		Cold	Off		Heavy	4
						5
	Quick	Warm	Medium	Auto	Light	2		X	X	X
		Cool	Slow	Timed	Normal	3
		Cold	Off		Heavy
	Cold Wash	Cool	Medium	Auto	Light	2		X	X	X
		Cold	Slow	Timed	Normal	3
			Off		Heavy	4
						5
Whites	Normal	Extra Hot	Extra Fast	Auto	Light	2		X	X	X
		Hot	Fast	Timed	Normal	3
		Warm	Medium		Heavy	4
		Cool	Slow			5
		Cold	Off
	Quick	Extra Hot	Extra Fast	Auto	Light	2		X	X	X
		Hot	Fast	Timed	Normal	3
		Warm	Medium		Heavy
		Cool	Slow
		Cold	Off
	Heavy Duty	Extra Hot	Extra Fast	Auto	Light	2		X	X	X
		Hot	Fast	Timed	Normal	3
		Warm	Medium		Heavy	4
		Cool	Slow			5
		Cold	Off
	Sanitize	Extra Hot	Extra Fast	Auto	Light	2			X	X
			Fast	Timed	Normal	3
			Medium		Heavy	4
						5
Towels	Normal	Extra Hot	Extra Fast	Auto	Light	2		X	X	X
		Hot	Fast	Timed	Normal	3
		Warm	Medium		Heavy	4
		Cool	Slow			5
		Cold	Off
	Quick	Extra Hot	Extra Fast	Auto	Light	2		X	X	X
		Hot	Fast	Timed	Normal	3
		Warm	Medium		Heavy
		Cool	Slow
		Cold	Off
	Heavy Duty	Extra Hot	Extra Fast	Auto	Light	2		X	X	X
		Hot	Fast	Timed	Normal	3
		Warm	Medium		Heavy	4
		Cool	Slow			5
		Cold	Off
	Sanitize	Extra Hot	Extra Fast	Auto	Light	2			X	X
			Fast	Timed	Normal	3
			Medium		Heavy	4
						5

7

What	How	Basic Settings					Additional Options
		Temperature	Spin Speed	Dry Mode	Set Soil Level	Rinses		Pre-Soak	Tumble Fresh™	Wrinkle Shield™
Bulky Items	Normal	Extra Hot	Medium	Auto	Light	2		X	X	X
		Hot	Slow	Timed	Normal	3
		Warm	Off		Heavy	4
		Cool				5
		Cold
	Quick	Extra Hot	Medium	Auto	Light	2		X	X	X
		Hot	Slow	Timed	Normal	3
		Warm	Off		Heavy
		Cool
		Cold
	Heavy Duty	Extra Hot	Medium	Auto	Light	2		X	X	X
		Hot	Slow	Timed	Normal	3
		Warm	Off		Heavy	4
		Cool				5
		Cold

Government energy certifications for this model were based on the REGULAR (WHAT TO WASH), NORMAL (HOW TO WASH), DRYING MODE – AUTO DRYING OFF, TIMED DRYING 4 HOURS, DRYING ONLY ON CYCLE WITH THE MAXIMUM DRYING TEMPERATURE SETTING. The as-shipped defaults of REGULAR (WHAT TO WASH), NORMAL (HOW TO WASH), WARM TEMP, SPIN SPEED EXTRA FAST, DRYING MODE – AUTO DRYING OFF, TIMED DRYING OFF, DRYING ONLY OFF were not used.

8

Choosing the Right Detergent

Use only High Efficiency detergents. The package will be marked “HE” or “High Efficiency.” Low-water washing creates excessive sudsing with a non-HE detergent. Using non-HE detergent

will likely result in longer cycle times and reduced rinsing performance. It may also result in component malfunction and, over time, buildup of mold or mildew. HE detergents should be low-sudsing and quick-dispersing to produce the right amount of suds for the best performance. They should hold soil in suspension so it is not redeposited onto clean clothes. Not all detergents labeled as High Efficiency are identical in formulation and their ability to reduce suds. For example, natural, organic, or homemade HE detergents may generate a high level of suds. Always follow the detergent manufacturer’s instructions to determine the amount of detergent to use.

Use only High Efficiency (HE) detergent.

About Detergent Concentration

Today’s liquid HE detergents are concentrated. Most brands of concentrated HE detergent will show the level of concentration on the bottle.

However, if the detergent bottle does not give the concentration, it can be easily calculated. Just divide the package size in fluid ounces by the number of loads. Then refer to the chart below to find the concentration.

Set the concentration level setting on the washer by using the Tools button (see Step 11 on page 13). If you do not get your desired cleaning results, set the concentration level to a lower concentration number. If you have excess suds, set the concentration level to a higher concentration number.

Concentration	Number of ounces ÷ number of loads
2X	1.5–2.49 (44.4 ml–73.6 ml)
3X	0.9–1.49 (26.6 ml–44.1 ml)
4X	0.7–0.89 (20.7 ml–26.3 ml)
5X	0.5–0.69 (14.8 ml–20.4 ml)
6X	0.3–0.49 (8.9 ml–14.5 ml)

Using the Load & Go™ Bulk Dispenser

Follow the steps below to fill the Load & Go™ bulk dispenser when using the washer for the first time, or when the low detergent icon or low fabric softener icon on the display indicate that the detergent or fabric softener level is running low.

1. Open the bulk container lid on the top of the washer/dryer.

2.Lift the fill door on the Liquid Detergent dispenser (Dispenser 1). Add liquid HE detergent up to the “MAX”

line. Do not overfill. Close the fill door. It will click into place. NOTE: If Dispenser 1 is empty, you may choose to add only enough liquid HE detergent for one load.

3.Lift the fill door on the Liquid Fabric Softener dispenser (Dispenser 2). Add liquid fabric softener up to the “MAX” line. Do not overfill. Close the fill door. It will click into place. NOTE: If Dispenser 2 is empty, you may choose to add only enough liquid fabric softener for one load.

4.Slowly close the bulk container lid. Make sure it is completely closed.

5.Make sure that the bulk dispenser is active. Use

the Tools button to make sure that both Dispenser 1 and Dispenser 2 are active and that the detergent concentration is correct. See Step 11 on page 13.

NOTES:

Use only High Efficiency (HE) detergent.

nDispenser 2 may be used as a second Liquid HE Detergent dispenser. Use the Tools button (go to “Load & Go™ Dispenser 2”) to change the content in Dispenser 2 and set the detergent concentration. Make sure that the other dispenser is disabled.

nThe entire Load & Go™ bulk container can be easily removed for ease of cleaning.

nThoroughly clean the Liquid Detergent dispenser (Dispenser 1) before switching to a different brand of detergent.

nThoroughly clean the Liquid Fabric Softener dispenser (Dispenser 2) before switching from liquid fabric softener to liquid detergent, before switching back from liquid detergent to liquid fabric softener, or before switching to a different brand of detergent.

	IMPORTANT:
	n Do not use chlorine bleach in this	Chlorine
	washer/dryer. Chlorine bleach will	Bleach
	damage it.

nDo not add a single-dose laundry packet to the bulk dispenser.

nDo not use powdered HE detergent in the bulk dispenser.

9

Using the All-In-One Washer/Dryer

First wash cycle without laundry

Before washing clothes for the first time, set up the Load & Go™ bulk dispenser (see page 9). Choose the Regular (What to Wash) and Quick (How to Wash) cycle and run it without clothes. Use only HE detergent. This initial cycle serves to ensure the interior is clean and the bulk dispenser is primed and ready for use before washing clothes.

If using liquid HE detergent in both Dispenser 1 and Dispenser 2, you will need to run a second cycle without laundry as indicated above to prime Dispenser 2 and clean the interior. Using the Tools button, make sure that Dispenser 1 is disabled when priming Dispenser 2 for detergent.

1. Sort and prepare your laundry

Sort items by recommended cycle, water temperature,

and colorfastness. Separate heavily soiled items from lightly soiled. Separate delicate items from sturdy fabrics. Treat stains promptly and check for colorfastness by testing stain remover products on an inside seam.

IMPORTANT:

nEmpty pockets. Loose change, buttons, or any small object can plug pumps and may require a service call.

nClose zippers, fasten hooks, tie strings and sashes, and remove non-washable trim and ornaments.

nMend rips and tears to avoid further damage to items during washing.

nTurn knits inside out to prevent pilling. Separate lint-takers from lint-givers. Synthetics, knits, and corduroy fabrics will pick up lint from towels, rugs, and chenille fabrics.

nDo not dry garments if stains remain after washing, because heat can set stains into fabric.

nAlways read and follow fabric care labels and laundry product instructions. Improper usage may cause damage to your garments.

2. If desired, instead of liquid detergent, add powdered HE detergent and/or laundry products

Powdered HE detergent, single-dose laundry packets, Oxi-type boosters, or scented crystals can be added to the drum prior to adding laundry. Make sure that the Load & Go™ bulk dispenser is disabled or off (see Step 11 on page 13), and skip Step 4 when using powdered HE detergent or single-dose laundry packets.

NOTES:

nAlways follow manufacturer’s instructions.

nDo not use chlorine bleach.

3.Load laundry into washer/dryer

Place a load of sorted items loosely in the washer/dryer. Items need to move freely for best cleaning and to reduce wrinkling and tangling. If using the drying option, loading the drum half full or less and not interrupting the drying cycle by opening the door will improve drying performance and cycle time. Close the washer/dryer door by pushing it firmly until the latch clicks.

nMix large and small items and avoid washing single items. Load evenly.

nWash small items in mesh garment bags. For multiple items, use more than one bag and fill bags equally.

10

4. Add liquid HE detergent to Load & Go™ bulk dispenser (if bulk dispenser is not already loaded or if low detergent icon on display is lit), if desired

6. Touch POWER button to turn on washer/dryer

See page 9 for instructions on how to fill the liquid detergent bulk dispenser (Dispenser 1). Press the TOOLS button and make sure that the bulk dispenser is active. See Step 11 on page 13.

NOTE: Do not add powdered HE detergent, single-dose laundry packets, Oxi-type boosters, or scented crystals to the bulk dispenser. They will not dispense correctly.

5. Add liquid fabric softener to Load & Go™ bulk dispenser (if bulk dispenser is not already loaded or if low fabric softener icon on display is lit), if desired

See page 9 for instructions on how to fill the fabric softener bulk dispenser (Dispenser 2). Press the TOOLS button and make sure that the bulk dispenser is active. See Step 11 on page 13.

IMPORTANT:

nDo not overfill or dilute fabric softener.

nDo not spill or drip any fabric softener onto the clothes.

nDo not use scented crystals in the bulk dispenser. They will not dispense correctly.

nDo not mix fabric softener and detergent in Dispenser 2 at the same time.

Touch until the indicators turn on.

7. Select wash program/cycle

4:28

3:15

What to Wash How to Wash

REGULAR NORMAL

Temperature	Spin Speed	Auto Dry
WARM	EXTRA FAST	Dry

From the home screen, touch the “What to Wash” area of the screen to select the program that best matches the items you want to wash. You may need to scroll down with your finger to see all of the selections. Touch the desired program to return to the home screen.

Touch the “How to Wash” area of the screen to select the program that best matches the method that you would like to wash those items. You may need to scroll down with your finger to see all of the selections. Touch the desired program to return to the home screen.

11

8. Select temperature and spin speed†

4:28

3:15

What to Wash How to Wash

REGULAR NORMAL

	Temperature		Spin Speed			Auto Dry
	WARM		EXTRA FAST			Dry

From the home screen, touch the “Temperature” area of the screen to show the Temperature settings available for the cycle/program chosen in Step 7. Touch the desired setting and touch OKAY to confirm that setting.

The recommended wash temperature is preset for each cycle. Some preset temperatures can be changed. You may select a different wash temperature based on the level of soil and

type of fabric being washed. For best results, use the warmest wash water safe for your fabric, following the garment label instructions. All wash temperatures feature a cold rinse.

Touch the “Spin Speed” area of the screen to show the Spin Speed settings available for the cycle/program chosen in Step 7. Touch the desired setting and touch OKAY to confirm that setting.

The recommended spin speed is preset for each cycle. Some preset speeds can be changed.

nFaster spin speeds mean shorter dry times, but may increase wrinkling in your load.

nSlower spin speeds reduce wrinkling, but will leave your load more damp.

Drying Function (Step 9)

9. Select drying function, if desired†

4:28

3:15

What to Wash How to Wash

REGULAR NORMAL

Temperature		Spin Speed		Auto Dry
WARM		EXTRA FAST		Dry

From the home screen, touch the “Drying Mode” area of the screen to show the available Drying Mode settings.

From the Drying Mode screen, choose between Auto-Drying and Timed-Drying. For Auto-Drying, touch Auto-Drying and then touch the screen to choose between Damp Dry, Dry, and Extra Dry. For Timed-Drying, touch Timed-Drying and then touch the screen to choose between :30 HR, 1:00 HR, 1:30 HR, 2:00 HR, 3:00 HR, and 4:00 HR. Expect longer drying times than with traditional vented dryers.

To run a dry cycle only:

Load the drum half full or less for optimal drying performance and cycle time. From the home screen, touch the “Drying Mode” area of the screen to show the available Drying Mode settings, and from the Drying Mode screen, after making the Auto-Drying or Timed-Drying choices as mentioned above, touch “DRYING ONLY ON.” Do not open the door during the drying cycle.

NOTE: If items to dry are highly saturated, run a high speed Spin cycle prior to running the Dry cycle.

IMPORTANT:

nDo not use dryer sheets.

nDo not dry comforters or large blankets.

†Not all options and settings are available with all programs/cycles. See “Cycle Guides” for available options and settings.

12

10. Select options, if desired†

From the home screen, touch the Options icon (at upper right of screen) and the Options screen will show Soil Level, Extra Rinses, Pre-Soak, Tumble Fresh,™ and Wrinkle Shield™ selections. Previously selected “What to Wash” and “How to Wash” options will be shown on the screen. Touch the screen for each option to change its setting.

Soil Level Option

The Soil Level option allows you to select a Light, Normal, or Heavy soil level setting. The recommended soil level is preset for each cycle. Some preset soil levels can be changed. For heavily soiled and sturdy fabrics, select the Heavy soil level setting. For lightly soiled and delicate fabrics, select the Light soil level setting. Lower soil level settings will help reduce tangling and wrinkling.

Extra Rinses Option

The Extra Rinses option provides one or more additional rinses to the selected cycle. The extra rinses can be canceled at any time by touching the “X” on the touch screen to the right of the estimated time remaining.

Pre-Soak Option

The Pre-Soak option can be set either on or off. Pre-Soak may be ended at any time by touching the “X” on the touch screen to the right of the estimated time remaining.

Tumble Fresh™ Option

The Tumble Fresh™ option will periodically tumble the load after the end of the cycle for up to 12 hours. Touch TUMBLE FRESH to activate this option. This option is not available when a drying mode is selected. Tumble Fresh™ may be ended at any time by touching the “X” on the touch screen to the right of the estimated time remaining.

Wrinkle Shield™ Option

The Wrinkle Shield™ option is only available when a drying mode is selected, and will periodically tumble the load after the end of the cycle for up to 12 hours. Wrinkle Shield™ may be ended at any time by touching the “X” on the touch screen to the right of the estimated time remaining.

†Not all options and settings are available with all programs/cycles. See “Cycle Guides” for available options and settings.

11. Use Tools button to change other settings, if desired

The Tools button gives access to many other settings, utility cycles, preferences, and information. Touch the TOOLS button to access the Tools screen, which contains the following

(you will need to scroll down with your finger to access all of the selections).

Load & Go™ Dispenser 1

Press this icon to access:

Load & Go™ Status Dispenser 1 and choose between:

nActive

nDisabled (1 Cycle)

nOff (Permanently)

Detergent Concentration Dispenser 1 and choose between:

n2X

n4X

n6X

n8X

Load & Go™ Dispenser 2

Press this icon to access:

Load & Go™ Status Dispenser 2 and choose between:

nActive

nDisabled (1 Cycle)

nOff (Permanently)

Load & Go™ Content Dispenser 2 and choose between:

nSoftener

nDetergent

Once set at Detergent:

Set Concentration Dispenser 2 and choose between:

n2X

n4X

n6X

n8X

Control Lock

Press this icon to lock the controls. Swipe up to unlock.

Mute

Press this icon to mute or unmute sounds.

Utility Cycles

Press this icon to access the following utility cycles: Spin, Drain, Rinse & Spin, and Clean Washer with affresh® cycle. Touch the utility cycle you wish to use and follow the screen prompts.

Preferences

Press to access Times and Dates, Sound Volume, Display Settings, and Regional. Follow the screen prompts.

WiFi

Press to access Connect to Network, SAID (Smart Appliance ID) Codes, Mac Address, and WiFi. Follow the screen prompts.

Info

Press to access Service & Support, Store Demo Mode, Restore Factory, WiFi Terms and Conditions, and Software Terms and Conditions. Follow the screen prompts.

13

12. Touch START/PAUSE button to begin cycle

Touch the START/PAUSE button to start the cycle.

To pause a cycle in progress, touch the START/PAUSE button once, then touch again to continue the cycle. To cancel a cycle, touch the “X” on the touch screen to the right of the estimated time remaining.

Once you touch the START/PAUSE button, you will hear the door lock. The washer/dryer door will remain locked during a wash cycle.

13. Touch POWER button to turn off washer/dryer after cycle ends

Touch the POWER button to turn off the washer/dryer at the end of a cycle. The Power button is also used to turn on the washer/dryer before use.

14. Remove garments promptly after cycle is finished

After a wash-only cycle, promptly remove

garments after cycle has completed to avoid odor and rusting of metal objects on

garments. When unloading garments, pull back the door seal and check for small items between the tub and the washer/dryer drum.

If you will be unable to remove the load promptly after a washonly cycle, use the Tumble Fresh™ option (see Step 10, page 13).

After a wash and dry cycle or a dry-only cycle, promptly remove garments after cycle has completed to reduce wrinkling. If you will be unable to remove a load promptly, use the Wrinkle Shield™ option (see Step 10, page 13).

NOTES:

nThe door will remain locked while the Tumble Fresh™ option is active after a wash-only cycle. To cancel the Tumble Fresh™ option and unlock the door, touch the “X” on the touch screen to the right of the estimated time remaining.

nThis washer/dryer has a tight seal to avoid water leaks.

To avoid odors, leave the door open to allow the washer/dryer to dry between uses.

nIf a dry cycle is interrupted and the load removed before the cool-down period at the end of the cycle, the load will be very hot.

Setting a delayed start

4:28

3:15

What to Wash How to Wash

REGULAR NORMAL

Temperature		Spin Speed		Auto Dry
WARM		EXTRA FAST		Dry

Touch POWER until the indicators turn on. From the home screen, make sure the washer/dryer is set to the correct time and date (if it is not, see Step 11 on page 13 for instructions on how to set the time and date).

Touch the clock icon on the far right portion of the touch screen. The “Select a start time” screen will show on the display. Scroll horizontally to select a preferred start time for your wash or dry cycle. The times will display in 15-minute increments. Press OKAY to set the start time. The display will return to the home screen and the clock icon will turn brown.

To delete or modify the delayed start, press the clock icon again and follow the screen prompts.

14

All-In-One Washer/Dryer Maintenance

CLEANING THE WASHER/DRYER LOCATION

Keep washer/dryer area clear and free from items that would block the airflow for proper dryer operation. This includes clearing piles of laundry in front of the washer/dryer.

WASHER/DRYER CARE

Recommendations to Help Keep Your Washer/Dryer Clean and Performing at its Best

1.Always use High Efficiency (HE) detergents and follow the HE detergent manufacturer’s instructions regarding the amount of HE detergent to use. Never use more than the recommended amount because that may increase the rate at which detergent and soil residue accumulate inside your washer, which in turn may result in undesirable odor.

2.Use warm or hot water washes sometimes (not exclusively cold water washes), because they do a better job of controlling the rate at which soils and detergent accumulate.

3.Always leave the washer/dryer door slightly ajar between uses to help dry out the washer/dryer and avoid the buildup of odor-causing residue.

4.Periodically clean residue from all interior surfaces of the glass window. For better care, wipe the entire inside of the glass door with a damp cloth.

Cleaning Your Front-Loading Washer/Dryer

Read these instructions completely before beginning the routine cleaning processes recommended below. This Washer Maintenance Procedure should be performed, at a minimum, once per month or every 30 wash cycles, whichever occurs sooner, to control the rate at which soils and detergent may otherwise accumulate in your washer/dryer.

Cleaning the Door Seal

1.Open the washer/dryer door and remove any clothing or items from the washer/dryer.

2.Inspect the seal between the door opening and the drum for stained areas or soil buildup. Pull back the seal to inspect all areas under the seal and to check for foreign objects.

3.If stained areas or soil buildup are found, wipe down these areas of the seal using the following procedure:

When the cycle is complete, gently pull back the rubber door seal and clean the entire surface with the textured side of an affresh® Machine Cleaning Wipe.

WASHER/DRYER CARE (cont.)

Cleaning the Inside of the Washer/Dryer

This washer/dryer has a special cycle that uses higher water volumes in combination with affresh® Washer Cleaner to thoroughly clean the inside of the washer/dryer.

NOTE: Read these instructions completely before beginning the cleaning process.

Begin procedure

Clean Washer with affresh® Cycle Procedure (Recommended for Best Performance):

a.Open the washer/dryer door and remove any clothing or items.

b.Use an affresh® Machine Cleaning Wipe or a soft, damp cloth or sponge to clean the inside door glass.

c.Add an affresh® Washer Cleaner tablet to the washer drum.

d.Do not add the affresh® Washer Cleaner tablet to the bulk dispenser.

e.Do not add any detergent or other chemical to the washer/dryer when following this procedure.

f.Close the washer/dryer door.

g.Select the Clean Washer with affresh® cycle.

h.Select the Tumble Fresh™ option to help dry the washer/dryer interior after the cycle is complete. NOTE: The washer/dryer remembers your last option selection and will use it for future wash cycles until you deselect that option.

i.Touch the START/PAUSE button to begin the cycle. The Clean Washer with affresh® cycle operation is described below.

Description of Clean Washer with affresh® Cycle Operation:

1.Do not run this cycle with a load. Doing so could damage the items.

2.After the cycle is complete, leave the door open slightly to allow for better ventilation and drying of the washer/ dryer interior.

Cleaning the Load & Go™ Bulk Dispenser

After a period of using your washer/dryer, you may find some residue buildup in the Load & Go™ bulk dispenser. To remove residue from the dispensers, lift the handle on the dispenser container housing to remove it from the washer/ dryer cabinet, then rinse the two dispensers thoroughly with running water. Wipe the outside dispenser container surfaces with an affresh® Machine Cleaning Wipe or a damp cloth and towel dry. Use an all-purpose surface cleaner, if needed. Replace the dispenser container in the washer/dryer cabinet and make sure that it is seated.

IMPORTANT: Load & Go™ bulk dispenser container is not dishwasher-safe.

Cleaning the Outside of the Washer/Dryer

Use an affresh® Machine Cleaning Wipe or a soft, damp cloth or sponge to wipe up any spills. Occasionally wipe the outside of your washer/dryer to help keep it looking new. Use an affresh® Machine Cleaning Wipe or mild soap and water.

IMPORTANT: To avoid damaging the washer/dryer finish, do not use abrasive products.

15