Whirlpool W11355369A, W11355370A-SP User Manual

FRONT LOAD WASHER OWNER'S MANUAL

MANUEL DE L’UTILISATEUR DE LA LAVEUSE À

CHARGEMENT FRONTAL

Table of Contents

Washer Safety

Internet Connectivity Guide Choosing the Right Detergent

Choosing the Right Detergent Adding Laundry Products

Washer Maintenance and Care.............................. . 5

Cleaning the Washer Location

Water Inlet Hoses............................................... 5

Washer Care...................................... ................5

Clean Washer Cycle Reminder Removing the Dispenser Cleaning Load & Go™ Containers (on some models)

Nonuse and Vacation Care .................................7

Winter Storage Care

Transporting Your Washer................................... 8

Reinstalling/Using Washer Again Cleaning the Drain Pump/Draining Residual Water (on some models)

Additional Cleaning ............................................9

Installation Instructions

Requirements............................................. ............9

Tools and Parts ..................................................9

Location Requirements Drain System

Electrical Requirements .................................... 12

Installation .................... ....................................... 12

Unpacking

Connect Drain Hose ................ ......................... 13

Connect Inlet Hoses ......................................... 14

Level Washer Complete Installation Checklist

........................................................ 2

...................................................2

....................................3

................................4

............................. 4

....................................4

............................. 5

........................... 6

..................................... 6

....................................................7

........................................... 7

......................... 8

.......................8

..........................................9

..................................... 10

................................................... 11

....................................................... 12

................................................... 15

.......................... 16

Table des matières

Sécurité de la laveuse .......................................... 17

Sécurité de la laveuse

Guide de connexion Internet

Choix du détergent approprié............................... 19

Choix du Détergent Approprié ........................... 19

Ajouter les produits de lessive ........................... 19

Entretien et réparation de la laveuse

Nettoyage de l'emplacement de la laveuse......... 20

Tuyaux d’arrivée d’eau Entretien de la laveuse Rappel de lancement du programme Clean Washer (nettoyage de la laveuse)

Retrait du distributeur ....................................... 22

Récipients Load & Go™ (sur certains modèles) Non utilisation et entretien avant les vacances Entretien pour entreposage hivernal Transport de la laveuse Réinstallation/réutilisation de la laveuse Nettoyage du filtre de la pompe de vidange / Vidange de l'eau résiduelle (sur certains modèles) Nettoyage supplémentaire

Instructions d’installation

Spécifications ...................................................... 25

Outils et pièces ................................................ 25

Exigences d’emplacement (laveuse) ................. 25

Système de vidange ......................................... 26

Spécifications électriques ................................. 27

L’installation............................................. ............ 28

Déballage ........................................................ 28

Raccordement du tuyau de vidange................... 29

Raccordement des tuyaux d’alimentation

Établissement de l’aplomb de la laveuse ............ 31

Liste de vérification pour installation terminée

....................................................... .. 23

....................................................... .. 24

......................................................... . 32

...................................... 17

................................ 18

.................... 20

...................................... 20

..................................... 20

..................... 22

.................. 23

..................................... 23

............. 23

................................ 24

..................................... 25

........... 29

W11355369A W11355370A-SP

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These

words mean:

You can be killed or seriously injured if you don't

DANGER

immediately follow instructions.

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

You can be killed or seriously injured if you don’t follow instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions,

including the following:

n Read all instructions before using the appliance. n Do not wash articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.

n Do not add gasoline, dry-cleaning solvents, or other

flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

n Under certain conditions, hydrogen gas may be produced

in a hot-water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot-water system has not been used for such a period, before using a washing machine, turn on all hot-water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

n Do not allow children to play on or in the appliance. Close

supervision of children is necessary when the appliance is used near children.

n Before the appliance is removed from service or discarded,

remove the door.

n Do not reach into the appliance if the tub or agitator is

moving.

n Do not install or store this appliance where it will be

exposed to the weather.

n Do not tamper with controls. n Do not repair or replace any part of the appliance or attempt

any servicing unless specifically recommended in the usermaintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.

n Do not use replacement parts that have not been

recommended by the manufacturer (e.g. parts made at home using a 3D printer).

n See the Installation Instructions for grounding requirements

and installation.

SAVE THESE INSTRUCTIONS

WARNING

Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel – Do not contact the thermostat bracket while the appliance is energized.

Internet Connectivity Guide for Connected Appliances Only

IMPORTANT: Proper installation of your appliance prior to use is your responsibility. Be sure to read and follow the installation

instructions that came with your appliance. Connectivity requires Wi-Fi and account creation. App features and functionality are subject to change. Data rates may apply. Once

installed, launch the app. You will be guided through the steps to set up a user account and to connect your appliance.

You Will Need:

n A home wireless router supporting Wi-Fi, 2.4Ghz with WPA2 security. If you are unsure of your router’s capabilities, refer to the router

manufacturer’s instructions.

n The router to be on and have a live internet connection. n The 10–character SAID code for your appliance. The SAID code is either printed on a label on the appliance or found on the LCD

screen.

Federal Communications Commission (FCC) Compliance Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Industry Canada (IC) Compliance Notice

This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

To comply with FCC and Industry Canada RF radiation exposure limits for general population, antenna(s) used for this transmitter must be installed such that a minimum separation distance of 20 cm is maintained between the radiator (antenna) and all persons at all times and must not be co-located or operating in conjunction with any other antenna or transmitter.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

n Reorient or relocate the receiving antenna. n Increase the separation between the equipment and receiver. n Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. n Consult the dealer or an experienced radio/TV technician for help.

CHOOSING THE RIGHT DETERGENT

Use only High Efficiency detergents. The package will be marked “HE” or “High Efficiency.” Low-water washing creates excessive sudsing with a non-HE detergent. Using non-HE detergent will likely result in longer cycle times and reduced rinsing performance. It may also result in component failure and, over time, buildup of mold or mildew. HE detergents should be lowsudsing and quick-dispersing to produce the right amount of suds for the best performance. They should hold soil in suspension so it is not redeposited onto clean clothes. Not all detergents labeled as High Efficiency are identical in formulation and their ability to reduce suds. For example, natural, organic, or homemade HE detergents may generate a high level of suds. If you use one of these and see an “Sd” or “Sud” error code appear in the display, consider using a different HE detergent. Always follow the detergent manufacturer’s instructions to determine the amount of detergent to use. Do not go over the Max line on the dispenser.

Adding Laundry Products

Adding HE detergent to basket:

Single-dose laundry packets, Oxitype boosters, color-safe bleach, or scented crystals can be added to the drum prior to adding laundry. When using single-dose laundry packets, make sure that the bulk dispenser is disabled (on some models) or off.

NOTE: Follow the manufacturer’s instructions to determine the amount of laundry products to use.

Adding liquid chlorine bleach to single-load dispenser:

Add liquid chlorine bleach to the bleach compartment. Do not overfill, dilute, or use more than 2⁄3 cup (165 mL). Do not use color-safe bleach or Oxi in the same cycle with liquid chlorine bleach.

IMPORTANT:

n Always measure liquid chlorine bleach. Use a measuring cup

with a pour spout; do not guess.

n Do not fill beyond the “MAX” line. Overfilling could cause

garment damage.

n Do not use thickened, easy-pour, or no-splash bleach when

running the Clean Washer with affresh may occur.

n On some models: Do not add liquid chlorine bleach to the bulk

dispenser.

n Slowly close dispenser drawers. Make sure the drawers are

closed completely (on some models).

Adding liquid fabric softener to single-load dispenser:

Pour a measured amount of liquid fabric softener into liquid fabric softener compartment. Always follow manufacturer’s directions for correct amount of fabric softener, based on your load size. Disable the 1-Liter Load & Go not used to dispense detergent (on some models).

Fabric softener is always dispensed in the last rinse, even if Extra Rinse is selected.

™ dispenser if

cycle, as excess suds

IMPORTANT: Do not overfill, dilute, or use more than the manufacturer-recommended quantity of fabric softener. Do not fill past the “MAX” line. Overfilling dispenser will cause fabric softener to immediately dispense into washer.

n Do not spill or drip any fabric softener onto the clothes. n Do not use liquid fabric softener dispenser balls in this washer.

They will not dispense correctly.

n Do not use fabric softener sheets, as they can stain the load.

Adding HE detergent to Optimal Dispense Drawer (on some models):

This compartment holds up to

14.3 oz. (424 ml) of liquid HE detergent allowing you to avoid having to refill detergent for each load. Also, this will use just the right amount of detergent required for a particular load/cycle.

NOTE: Do not add single-dose laundry packets, Oxi-type boosters, color-safe bleach, or fabric softener crystals to dispensers. They will not dispense correctly.

Adding HE detergent to Load & Go models):

Use only High Efficiency (HE) liquid detergents. The bulk dispensers will hold about 67.6 oz. (2 L) or 33.8 oz. (1 L) of liquid HE detergent, depending on dispenser, or enough for many loads of laundry.

To fill bulk dispensers (on some models):

Open the dispenser drawer by pulling on the handle at the base of the washer. If desired, the drawer can be completely removed from the washer.

Locate the Load & Go pull up on the tab located on the bulk dispenser lid to lift the fill door.

Fill to the “MAX” line (see illustrations at right) with HE liquid detergent or liquid fabric softener (1-liter dispenser only). Close fill door. It will click into place. Make sure the concentration setting is correct (see the online “Cycle Guide”).

It is recommended that you rinse out the Load & Go

™ containers when refilling, when changing

detergent types or concentrations, or when the washer will not be used for an extended period. For instructions on cleaning the dispenser cartridge, see “Washer Care” in the “Washer Maintenance and Care” section of your Owner’s Manual.

Adding HE detergent to single-load dispenser:

Pour a measured amount of HE detergent into detergent compartment. For powdered detergent, lift the selector to the high position. For liquid detergent, push down the selector to the low position.

Do not overfill; adding too much detergent may cause detergent to be dispensed into the washer too early.

™ bulk dispenser. Gently

™ dispenser (on some

IMPORTANT:

n Disable the Load & Go

(on some models).

n Do not add single-dose laundry packet to dispenser drawer.

Powdered detergent:

Lift the selector to the high

position. Add directly to the

compartment.

™ option before starting a single load

Liquid detergent:

Push down the selector to the

low position. Add directly to the

compartment.

WASHER MAINTENANCE AND CARE

Cleaning the Washer Location

Keep washer area clear and free from items that would block airflow. This includes clearing piles of laundry in front of the washer.

Water Inlet Hoses

Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses: n Mark the date of replacement on the label with a permanent

marker.

n Check that the old washers are not stuck on the washer inlet

valves.

n Use new washers in the new inlet hoses to ensure a proper

seal.

Washer Care

Recommendations to Help Keep Your Washer Clean and Performing at Its Best

1. Always use High Efficiency (HE) detergents and follow the HE

detergent manufacturer’s instructions regarding the amount of HE detergent to use. Never use more than the recommended amount because that may increase the rate at which detergent and soil residue accumulate inside your washer, which, in turn, may result in undesirable odor.

2. Use warm or hot water washes sometimes (not exclusively

cold water washes), because they do a better job of controlling the rate at which soils and detergent accumulate.

3. Always leave the washer lid open between uses to help dry

out the washer and prevent the buildup of odor-causing residue.

4. Periodically clean residue from all interior surfaces of the

window. For better care, wipe the entire inside of the door with a damp cloth.

Cleaning Your Front-Loading Washer

Read these instructions completely before beginning the routine cleaning processes recommended below. This Washer Maintenance Procedure should be performed, at a minimum, once per month or every 30 wash cycles, whichever occurs sooner, to control the rate at which soils and detergent may otherwise accumulate in your washer.

Cleaning the Door Seal

1. Open the washer door and remove any clothing or items from

the washer.

2. Inspect the gray-colored seal between the door opening and

the drum for stained areas, soil buildup, or lint. Pull back the seal to inspect all areas under the seal and to check for foreign objects or lint.

3. If stained areas, soil buildup, or lint are found, wipe down

these areas of the seal using either of the following two procedures:

a. affresh

b. Dilute Liquid Chlorine Bleach Procedure:

IMPORTANT:

n Wear rubber gloves when cleaning with bleach. n Refer to the bleach manufacturer’s instructions for proper

use.

Machine Cleaning Wipes Procedure:

i. When the cycle is complete, gently pull back the

rubber door seal and clean the entire surface with the textured side of an affresh

i. Mix a dilute bleach solution, using 3/4 cup (177 mL)

of liquid chlorine bleach and 1 gallon (3.8 L) of warm tap water.

ii. Wipe the seal area with the dilute solution, using a

damp cloth.

iii. Let stand 5 minutes. iv. Wipe down area thoroughly with a dry cloth and let

washer interior air dry with door open.

Machine Cleaning Wipe.

Cleaning the Inside of the Washer

This washer has a special cycle that uses higher water volumes in combination with affresh chlorine bleach to thoroughly clean the inside of the washer. Steam washer models also utilize steam to enhance cleaning in this special cycle.

IMPORTANT: Do not use thickened, easy-pour, or no-splash bleach when running the Clean Washer with affresh excess suds may occur.

NOTE: Read these instructions completely before beginning the cleaning process.

Washer Cleaner or regular liquid

cycle as

Begin Procedure

1. Clean Washer with affresh®Cycle Procedure (Recommended for best performance):

a. Open the washer door and remove any clothing or items. b. Use an affresh

cloth or sponge to clean the inside door window.

c. Add an affresh

drum.

d. Do not add the affresh

dispenser drawer.

e. Do not add any detergent or other chemical to the washer

when following this procedure. f. Close the washer door. g. Select the Clean Washer with affresh h. On some models: Select the FanFresh

Fresh Spin

the cycle is complete. NOTE: The washer remembers your last option selection and

will use it for future wash cycles until you deselect that option. i. Touch and hold Start/Pause to begin the cycle. See the

“Description of Clean Washer with affresh

Operation” section.

Machine Cleaning Wipe or a soft, damp

Washer Cleaner tablet to the washer

Washer Cleaner tablet to the

cycle.

™ option to help dry the washer interior after

/Fresh Hold®/

Cycle

2. Chlorine Bleach Procedure:

a. Open the washer door and remove any clothing or items. b. Open the dispenser drawer and add liquid chlorine bleach

to the Max level in both the bleach compartment and the fabric softener compartment. Either traditional or HE chlorine bleach can be used.

IMPORTANT: Do not use thickened, easy-pour, or no-splash bleach as excess suds may occur.

NOTE: Use of more liquid chlorine bleach than is recommended above could cause washer damage over time.

c. Close the washer door and the dispenser drawer. d. Do not add any detergent or other chemicals to the

washer when following this procedure.

e. Select the Clean Washer with affresh f. On some models: Select the FanFresh

Fresh Spin

™ option to help dry the washer interior after

cycle.

/Fresh Hold®/

the cycle is complete.

NOTE: The washer remembers your last option selection and will use it for future wash cycles until you deselect that option.

g. Touch and hold Start/Pause to begin the cycle. See the

“Description of Clean Washer with affresh

Cycle

Operation” section.

NOTE: For best results, do not interrupt cycle.

Description of Clean Washer with affresh®Cycle Operation

1. The Clean Washer with affresh®cycle will determine whether

clothing or other items are in the washer.

2. If no items are detected in the washer, it will proceed with the

cycle. a. If any items are detected in the washer, “rL” (remove

load) will be displayed. The door will unlock. Open

washer and remove any garments from the washer drum. b. Touch Power to clear the “rL” code. c. Touch and hold Start/Pause to restart the cycle.

3. Steam models only: During the first 20 minutes of the cycle,

it will activate the steamer but the drum will not spin or fill with water. You may see condensation on the door window during this initial phase. If you are using an affresh

Washer Cleaner tablet, it will not dissolve completely during the steam phase. This is normal.

After the cycle is complete, leave the door open slightly to allow for better ventilation and drying of the washer interior.

Cleaning the Dispensers

After a period of using your washer, you may find some residue buildup in the washer’s dispensers.

For the Single-Load or Optimal dispenser: Remove the drawer and wipe the surfaces with an affresh a damp cloth, and towel dry either before or after you run the Clean Washer with affresh

cycle. Use an all-purpose surface

cleaner, if needed.

For the Load & Go

™ dispenser: Lift the handle on the dispenser

housing and pull to remove it from the washer cabinet; then rinse the dispenser thoroughly with running water. Wipe the outside dispenser surface with an affresh damp cloth, and towel dry. Use an all-purpose surface cleaner, if needed.

Replace the dispenser in the washer cabinet and make sure that it is correctly seated.

IMPORTANT: Dispensers are not dishwasher-safe.

Machine Cleaning Wipe or

Machine Cleaning Wipe or a

Cleaning the Outside of the Washer

IMPORTANT: To avoid damaging the washer’s finish, do not use

abrasive products. Use an affresh

sponge to wipe up any spills. Occasionally wipe the outside of your washer to help keep it looking new. Use an affresh

Machine Cleaning Wipe or a soft, damp cloth or

Machine

Cleaning Wipe or mild soap and water.

Clean Washer Cycle Reminder

NOTE: Not all models have the Clean Washer with affresh®cycle

reminder light. The Clean Washer with affresh

wash cycle when the washer has run 30 wash cycles. This is a reminder to run the Clean Washer with affresh

If the Clean Washer with affresh

message will flash at the end of a

cycle.

cycle is not run, the message will stop flashing at the end of a wash cycle after running three more regular wash cycles. After 30 more wash cycles are completed, the Clean Washer with affresh

message will again

flash at the end of a wash cycle as a reminder.

Removing the Dispenser

Optimal Dispenser Drawer (on some models)

To remove:

1. Pull dispenser drawer out until it stops.

2. Press down on the release tab and pull straight out to remove

the dispenser.

3. Lift off cover panel by pulling straight up.

To replace:

1. Slide cover panel back onto posts on dispenser.

2. Align edges of dispenser with guides in washer; then slide

dispenser back into slot.

Single-Load Dispenser Drawer (on some models)

To remove:

1. Pull dispenser drawer out until it stops.

2. Press down on the release tab and pull straight out to remove

the dispenser.

Cleaning Load & Go™ Containers (on some models)

IMPORTANT: Containers are not dishwasher-safe.

It is recommended that you rinse out the Load & Go when refilling, when changing detergent types or concentrations, or when the washer will not be used for an extended period.

1. Pull the dispenser drawer out until it stops.

2. Lift out the Load & Go

3. Lift the fill lid and flush interior thoroughly with warm water.

4. Allow to air dry.

™ containers.

™ containers

Nonuse and Vacation Care

Operate your washer only when you are home. If moving, or not using your washer for a period of time, follow these steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer to avoid flooding due to water

pressure surges. HELPFUL TIP: Attach a reminder note to the washer to turn

the water back on before washer's next use.

3. Clean the dispensers. See “Cleaning the Dispensers.”

3. Lift off cover panel by pulling straight up.

To replace:

1. Position cover panel back onto posts on dispenser. Apply

slight pressure on cover panel to seat it.

2. Align edges of dispenser with guides in washer; then slide

dispenser back into slot.

Winter Storage Care

IMPORTANT: To avoid damage, install and store washer where it

will not freeze. Because some water may stay in hoses, freezing can damage washer. If storing or moving during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water inlet

hoses. HELPFUL TIP: Attach a reminder note to the washer to turn

the water back on before washer’s next use.

2. Remove drain pump filter.

3. Put 1 qt. (1 L) of R.V.-type antifreeze in drum and run washer

on Normal cycle for about 2 minutes to mix antifreeze and remaining water.

4. Unplug washer or disconnect power.

Transporting Your Washer

1. Shut off both water faucets. Disconnect and drain water inlet

hoses.

2. If washer will be moved during freezing weather, follow

“Winter Storage Care” directions before moving.

3. Disconnect drain hose from drain system and from back of

washer.

4. Unplug power cord.

5. Place inlet hoses and drain hose inside drum.

6. Bundle power cord with a rubber band or cable tie to keep it

from hanging to the ground.

IMPORTANT: Call for service to install new transport bolts. Do not reuse transport bolts. Washer must be transported in the upright position. To avoid structural damage to your washer, it must be properly set up for relocation by a certified technician.

Reinstalling/Using Washer Again

Cleaning the Drain Pump/Draining Residual Water (on some models)

IMPORTANT: Make sure the washer is off before cleaning the

drain pump filter.

NOTE: Perform the following procedure occasionally.

1. Open the dispenser drawer by pulling on the handle at the

base of the washer. This will reveal the drain pump filter. Remove the drawer by releasing the tab on each side.

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

To reinstall washer after nonuse, vacation, winter storage, or moving:

1. Refer to Installation Instructions to locate, level, and connect

washer.

2. Before using again, run washer through the following

recommended procedure:

To use washer again:

1. Flush water pipes and hoses.

2. Reconnect water-inlet hoses.

3. Turn on both water faucets.

4. Plug into a grounded 3-prong outlet or reconnect power.

5. Run washer through Heavy Duty/Power Wash cycle to clean

washer and remove antifreeze, if used. Use only HE detergent. Use half the manufacturer’s recommended amount for a medium-size load.

With your finger, push down on tab on right side of drawer, and up on tab on left side of drawer.

2. Place a broad, flat container beneath the drain pump filter to

collect the drain water. Release the black hose from the hose clip, remove the plug, and drain the hose into the container. Empty the container. Repeat this procedure if necessary until all the water has drained. Make sure that the black hose is completely dry, replace the plug, and secure the hose in the clip.

NOTE: If water does not drain well, push in hose slightly to remove any possible kinks.

3. Lay a cotton cloth beneath the drain pump filter to absorb any

water still in it. Then remove the drain pump filter by turning it counterclockwise.

4. Remove large clumps of lint by hand from the filter and place

lint in a suitable waste container. Remove remaining residue from the filter by rinsing with water.

INSTALLATION INSTRUCTIONS REQUIREMENTS

Tools and Parts

Gather required tools and parts before starting installation.

Tools Needed:

5. Reinsert the drain pump filter by turning it clockwise. Make

sure to turn it in as far as it will go, with the filter handle remaining as close as possible to the vertical position.

6. Replace and close the dispenser drawer. Make sure to insert

both rails simultaneously when replacing the drawer. You will hear a clicking sound that indicates the rails have engaged. To ensure proper placement of the drawer, pull out fully. The drawer should be fully engaged and the rails locked in place. Make sure the drain hose is secured in the hose clip and tucked underneath the cutout.

Adjustable or open end wrenches 1/2″ (13 mm), 5/8″ (16 mm), and 9/16″ (14.3 mm)

Wood block Ruler or measuring tape

Adjustable pliers that open to 1 9/16″ (39.7 mm)

Level

Flashlight

Additional Cleaning

Gently pull back the rubber door seal and clean any stained areas, soil buildup, or lint with the textured side of an affresh Cleaning Wipe.

Machine

Bucket

Parts Supplied:

NOTE: All parts supplied for installations are in the washer.

Drain hose with clamp, U-form, and cable tie

Parts Needed: (if not supplied with washer)

NOTE: Various inlet hose

options are available; check your Quick Start Guide for ordering information.

Inlet hoses with flat washers

Available Accessories

An optional matching pedestal is available for your washer. Please contact your retailer for ordering information, or see your Quick Start Guide.

Alternate Parts (not supplied with washer)

Your installation may require additional parts. To order, please refer to contact information on your Quick Start Guide.

If you have: You will need:

Recessed area or closet installation (stacked washer and dryer)

Overhead sewer Standard 20 gal. (76 L) 39" (990 mm)

tall drain tub or utility sink, sump pump, and connectors (available from local plumbing suppliers)

Location Requirements

IMPORTANT: Do not install, store, or operate washer where it will

be exposed to weather or in temperatures below 32°F (0°C). Water remaining in washer after use may cause damage in low temperatures. See “Washer Maintenance and Care” for winterizing information.

Select proper location for your washer to improve performance and minimize noise and possible “washer walk.” Install your washer in a basement, laundry room, closet or recessed area.

Proper installation is your responsibility.

You will need

n A water heater set to 120°F (49°C). n A grounded electrical outlet located within 6 ft. (1.8 m) of

power cord on back of washer.

n Hot and cold water faucets located within 4 ft. (1.2 m) of hot

and cold water fill valves on washer, and water pressure of 20– 100 psi (137.9–689.6 kPa).

n A level floor with maximum slope of 1" (25 mm) under entire

washer. Installing on carpet or surfaces with foam backing is not recommended.

n Floor must support washer’s total weight (with water and load)

of 315 lbs. (143 kg).

All dimensions show minimum spacing allowed. For each arrangement, consider allowing more space for ease of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and floor moldings. Space must be large enough to allow door to fully open. Add spacing of 1" (25 mm) on all sides of washer to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings in door are required.

NOTE: For additional details (or information) specific to your model, refer to your Quick Start Guide.

Custom under counter installation

Recessed area or closet installation (washer only)

+ 22 hidden pages