Whirlpool W10882520 Installation manual

Installation Instructions Instrucciones de instalación Instructions d’installation
Stack Kit Juego para lavadora y secadora Enemble superposé
Kit Number W10882520 Número de juego W10882520 Ensemble numéro W10882520
For use only with front-load washers and dryers Para uso sólo con lavadoras y secadoras de carga frontal Pour utilisation avec laveuses et sécheuses à chargement
par l’avant seulement
If you have any problems or questions, visit us at www.whirlpool.com
Si tiene cualquier problema o duda, visítenos en www.whirlpool.com
Pour tout problème ou toute question, consulter www.whirlpool.ca
W10882518A
Table of Contents
STACK KIT SAFETY ............................ 2
INSTALLATION REQUIREMENTS ..... 2
Tools and Parts ............................. 2
Location Requirements ................. 3
Uninstall Washer and Dryer .......... 4
If Your Washer or Dryer
is Still in Its Packaging .................. 4
INSTALLATION INSTRUCTIONS ....... 4
To Use Stacking Shelf
and Hanging Rack ........................ 6
STACK KIT SAFETY
Índice
SEGURIDAD DEL JUEGO PARA LAVADORA Y
SECADORA SUPERPUESTAS ........... 7
REQUISITOS DE INSTALACIÓN ....... 7
Herramientas y piezas .................. 7
Requisitos de ubicación ............... 8
Como desinstalar la lavadora
y la secadora ................................ 9
Si su lavadora o secadora
está aún en su empaque .............. 9
INSTRUCCIONES
DE INSTALACIÓN .............................. 9
Uso del estante para apilar
y el colgador ............................... 11
Table des matières
SÉCURITÉ DE L’ENSEMBLE
SUPERPOSÉ ..................................... 12
EXIGENCES D’INSTALLATION ....... 12
Outillage et pièces ...................... 12
Exigences d’emplacement ......... 13
Désinstallation de la laveuse
et de la sécheuse ........................ 14
Si la laveuse ou la sécheuse est encore dans son emballage .. 14
INSTRUCTIONS
D’INSTALLATION ............................. 14
Pour utiliser la tablette d’empilage et la tringle
de suspension ............................. 16
INSTALLATION REQUIREMENTS
TOOLS AND PARTS
Gather the required tools and parts before starting installation.
Tools needed:
Phillips screwdriver Adjustable wrench that
Level
opens to 1" (25 mm)
Bucket
2
Pliers or slip-joint pliers (for drain and inlet hoses)
Tape measure
Parts supplied:
Stacking platform (1)
Lower brackets for 24" (620 mm) deep models (Marked A) (2)
LOCATION REQUIREMENTS Recessed Area and Closet Installation Instructions
IMPORTANT: The stacked washer/dryer can be installed in
an enclosure. Check the locations of the water supply faucets and grounded electrical outlets. Depending on your application, washer ll hoses longer than those supplied with the washer/dryer may be needed.
0"/1"
(0 mm/25 mm)
3"
683⁄4" Min.
(1746 mm)
653/4"
691⁄2" Max.
(1670 mm)
(1765 mm)
(76 mm)
2
48 in.
(310 cm2)
Lower brackets for 22" (550 mm) deep models
Upper brackets (Marked C) (2)
(Marked B) (2)
Plastic pads (2)
Plastic pads (2)
Rubber pads (2) Rubber pads (2)
2
0"/1"
(0 mm/25 mm)
0"/1"
(0 mm/25 mm)
(76 mm)
0"/1"
(0 mm/25 mm)
3"
24 in.
(155 cm2)
If the water supply faucets, electrical outlets, or power cord need modication, have a qualied plumber or electrician make the changes.
Pan-head screws (4)
3
UNINSTALL WASHER AND DRYER IMPORTANT: If your washer and dryer are already installed,
they must be uninstalled. If you need to uninstall your washer or dryer, see the Installation
Instructions that came with your model for tools required.
Uninstalling Your Washer
1. Turn off the water faucet(s).
2. Unplug the power supply cord.
3. Slowly loosen the fill hose(s) at the faucet(s) to relieve the
water pressure. Use a sponge or towel to absorb the released water.
4. Remove the fill hose(s) from the back of the washer. Drain
water in the hose(s) into a bucket.
5. Remove the drain hose from the wall/floor drain pipe or utility
sink and drain any water in the hose into a bucket.
Uninstalling Your Dryer
1. Disconnect the power supply.
2. Remove the drain hose from the floor drain pipe or utility sink
and drain any water in the hose into a bucket.
IF YOUR WASHER OR DRYER IS STILL IN ITS PACKAGING
INSTALLATION INSTRUCTIONS
1. Move washer
48"
(1.2 m)
It is necessary to remove all shipping materials for proper operation and to avoid excessive noise from washer.
Move washer to within 48" (1.2 m) of its nal location. It must be in a fully upright position.
IMPORTANT: Keep the feet on the washer even in a stacked installation.
Position the packaged washer or dryer close to its nal position. Cut the packaging as follows:
n
Washer: Cut plastic lm along dotted cut line around the
base. Remove the packaging. Do not remove the shipping bolts.
n
Dryer: Cut around top and down corners along dotted cut
lines. Discard carton top, corner posts and sides. Leave carton bottom underneath dryer.
2. Ensure washer is level in its nal
location
Place level here.
Place a level on top edges of washer, checking each side and front. If not level, tip washer and adjust feet up or down as shown in Installation Instructions, repeating as necessary.
Not Level LEVEL Not Level
4
3. Install pads on stacking platform
Bottom side up
Turn the platform upside down. Install front and rear plastic pads in positions shown. Make sure they are also oriented as indicated. Then install the rubber pads over the plastic pads as shown.
5. Remove screws from top rear
of washer
6. Flip over stacking platform and place
on top of washer
Top side up
4. Install brackets
A
C
Bottom side up
Rear
Slide lower brackets (A) into tracks as shown. Fasten them in place using upper brackets (C) and screws provided.
Make sure lower bracket holes are aligned with screw holes on top rear of washer.
7. Fasten stacking platform to top
of washer
Use screws removed in Step 5 to fasten platform to washer.
5
Loading...
+ 11 hidden pages