How it Works
show menu
Whirlpool
Loading...
W10200890B

Whirlpool W10200890B, W10200891B - SP, NTW4500, NTW4800, NTW4600 Installation Instructions Manual

...
0 (0)
WASHER INSTALLATION INSTRUCTIONS
INSTRUCTIONS POUR L’INSTALLATION DE LA LAVEUSE
Table of Contents Table des matières
WASHER SAFETY .........................................................1
INSTALLATION REQUIREMENTS ................................2
Tools and Parts ................................................................2
Location Requirements ..................................................2
Drain System ...................................................................3
Electrical Requirements .................................................4
INSTALLATION INSTRUCTIONS ..................................4
Before you start: remove shipping materials ...............4
Connect Drain Hose ........................................................5
Connect Inlet Hoses ........................................................6
Level Washer ...................................................................7
Complete Installation Checklist .....................................8
INSTALLATION NOTES
Date of purchase: _________________________________ Date of installation: _______________________________ Installer: ________________________________________ Model number: ___________________________________ Serial number: ___________________________________
SÉCURITÉ DE LA LAVEUSE ................................................9
EXIGENCES D’INSTALLATION ................................................. 9
Exigences d’emplacement .................................................... 10
Système d’évacuation ............................................................. 10
INSTRUCTIONS D’INSTALLATION ........................................ 12
Avant de commencer : retrait du matériel d’expédition ...... 13
Raccordement des tuyaux d’arrivée d’eau ........................... 15
Établissement de l’aplomb de la laveuse .............................. 15
NOTES CONCERNANT L’INSTALLATION
Date d’achat : ______________________________________ Date d’installation : _________________________________ Installateur : _______________________________________ Numéro de modéle : _________________________________ Numéro de série : ___________________________________
W10200890B W10200891B - SP
WASHER SAFETY
1
INSTALLATION REQUIREMENTS
27"
(686 mm)
42"
(1067 mm)
25
1
/2"
(648 mm)
4" min
(102 mm)
TOOLS AND PARTS
Gather required tools and parts before starting installation.
Tools needed:
Adjustable or open end wrench 9/16" (14 mm)
Wood block
Pliers that open to 19⁄16" (39.5 mm)
Optional tools:
Level
Ruler or measuring tape
Parts needed: (Not supplied with washer)
Inlet hoses with flat washers
To order, please refer to the phone number or website on back page of your Washer User Instructions.
n
8212656RP 10 ft. (3.0 m) Inlet hose, Black EPDM (2 pack)
n
8212641RP 5 ft. (1.5 m) Inlet hose, Black EPDM (2 pack)
n
8212646RP 4 ft. (1.2 m) Inlet hose, Black EPDM (2 pack)
n
8212545RP 5 ft. (1.5 m) Inlet hose, Red and Blue EPDM
(2 pack)
n
8212487RP 5 ft. (1.5 m) Nylon braided inlet hose (2 pack)
n
8212638RP 6 ft. (1.8 m) Nylon braided inlet hose, space
saving 90° elbow, hypro-blue steel couplings (2 pack)
n
8212637RP 6 ft. (1.8 m) Inlet hose, Black EPDM, space
saving 90° elbow, hypro-blue steel couplings (2 pack)
Alternate parts: (Not supplied with washer)
Your installation may require additional parts. To order, please refer to the phone number or website on the back page of your Washer User Instructions.
Flashlight
Bucket
Parts supplied:
NOTE: All parts supplied for installation are in
washer basket.
Beaded Tie Strap
Drain hose form
Front leveling feet with jam nuts (2)
If you have: You will need:
Overhead sewer Standard 20 gal. (76 L) 39" (991 mm) tall drain tub or utility sink, sump pump, and connectors (available from local suppliers)
Short drain hose Drain Extension Kit Part Number 49022 1" (25 mm) 2" (51 mm) diameter to 1" (25 mm) diameter
diameter standpipe Standpipe Adapter Kit, Part Number 40923 Connector Kit, Part Number 285835
Lint clogged drain Drain protector, Part Number 376031
Floor drain Siphon Break Kit, Part Number 280129A Drain Hose, Part Number 285702 Connector Kit, Part Number 285835
LOCATION REQUIREMENTS
Select proper location for your washer to improve performance and minimize noise and possible “washer walk”. Install your washer in a basement, laundry room, closet, or recessed area.
2
You will need:
3"
(76 mm)
3"
(76 mm)
24 in.
2
(155 cm2)
48 in.
2
(310 cm2)
19"
(483 mm)
1"
(25 mm)
0"
(0 mm)
4"
(102 mm)
14" max. (356 mm)
4.5"
(113 mm)
39"
(991 mm)
4.5"
(113 mm)
39"
(991 mm)
4.5"
(113 mm)
n
A water heater set to 120° F (49° C).
n
A grounded electrical outlet located within 4 ft. (0.9 m)
of power cord on back of washer.
n
Hot and cold water faucets located within 3 ft. (0.9 m)
of hot and cold water ll valves on washer, and water pressure of 5-100 psi (34.5-690 kPa).
n
A level oor with maximum slope of 1" (25 mm) under entire
washer. Installing on carpet is not recommended.
n
Floor must support washer’s total weight (with water
and load) of 315 lbs (143 kgs).
IMPORTANT: Do not install, store, or operate washer where it will be exposed to weather or in temperatures below 32° F (0° C). Water remaining in washer after use may cause damage in low temperatures. See “Washer Care” in Washer User Instructions for winterizing information.
Proper installation is your responsibility.
Recessed area or closet installation
DRAIN SYSTEM
Drain system can be installed using a oor drain, wall standpipe, oor standpipe, or laundry tub. Select method you need.
IMPORTANT: To avoid siphoning, no more than 4.5" (113 mm)
of drain hose should be inside standpipe or below the top of wash tub. Secure drain hose with beaded tie strap (A).
Floor standpipe drain system
A
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum carry-away capacity: 17 gal. (64 L) per minute. Some standpipes may require a Standpipe Adapter Kit and additional drain hose that may be purchased separately. See “Tools and Parts”. Top of standpipe must be at least 39" (991 mm) high; install no higher than 96" (2.4 m) from bottom of washer. Installations higher than 96" (2.4 m) require a sump pump system.
Wall standpipe drain system
Dimensions show recommended spacing allowed, except for closet door ventilation openings which are minimum required. Consider allowing more space for ease of installation and servicing, spacing for companion appliances and clearances for walls, doors, and oor moldings. Add spacing of 1" (25 mm) on all sides of washer to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings in door are required.
A
See requirements for oor standpipe drain system.
Floor drain system
Floor drain system requires a Siphon Break Kit and additional drain hose that may be purchased separately. See “Tools and Parts”. Minimum siphon break: 28" (711 mm) from bottom of washer. (Additional hoses might be needed.)
Laundry tub drain system
A
Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at least 39" (991 mm) above oor; install no higher than 96" (2.4 m) from bottom of washer.
3
36"
(914 mm)
ELECTRICAL REQUIREMENTS
GROUNDING INSTRUCTIONS
For a grounded, cord-connected washer:
This washer must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by providing a path of least resistance for electric current. This washer is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded.
Do not modify the plug provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
For a permanently connected washer:
This washer must be connected to a grounded metal, permanent wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.
n
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical
supply is required. A time-delay fuse or circuit breaker on a separate circuit serving only this washer is recommended.
n
This washer is equipped with a power supply cord having a
3 prong grounding plug.
n
To minimize possible shock hazard, the cord must be
plugged into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualied electrician.
n
If codes permit and a separate ground wire is used, it is
recommended that a qualied electrician determine that the ground path is adequate.
n
Check with a qualied electrician if you are not sure the
washer is properly grounded.
INSTALLATION INSTRUCTIONS
Before you start: remove shipping materials
It is necessary to remove all shipping materials for proper operation and to avoid excessive noise from washer.
1. Move washer
Move washer to within 3 ft (914 mm) of its nal location; it must be in a fully upright position.
NOTE: To avoid oor damage, set washer onto cardboard
before moving it.
2. Locate shipping materials
4
Straight power cord Looped power cord
Locate yellow shipping materials on back of washer, near bottom. If it is a straight power cord and cord restraint, follow steps 3 & 4 then continue to step 6; if power cord is looped, skip to step 5.
Remove straight power cord
3.
and cord restraint
C
D
6. Place power cord over console
A
Firmly grasp power cord (A) and pull to completely free power cord, cord restraint (B), and pin (C) from rear panel. Pull cord restraint strap (D) out of plug.
NOTE: Remove cotter pin if it did not come free with strap.
B
4. Remove restraint from power cord
tab
power cord
To remove restraint from power cord: push power cord in, press tab, and then pull power cord out.
restraint
5. Remove looped power cord
Gently place power cord over console to allow free access to back of washer.
CONNECT DRAIN HOSE
Remove drain hose from washer
7.
cabinet
Gently pull hose out of back of washer cabinet from top until end emerges.
IMPORTANT: Do not force excess drain hose back into rear
of washer.
A
B
Firmly grasp yellow shipping strap (A) and pull until both ends are completely removed from washer. Pull cord restraint strap (B) out of plug.
NOTE: Check that two (2) cotter pins (C) came off with strap.
C
8. Connect drain hose form
For a laundry tub or standpipe drain, follow steps 8 and 9. For a oor drain, do not install drain hose form. You may need alternate parts with separate directions. See “Tools and Parts” to determine what you may need.
Feed hose into one end of form. Bend hose and feed through other side, anchoring form on smooth sections of hose.
5
Loading...
+ 11 hidden pages
Privacy Policy Cookie Policy Terms of Use