Whirlpool UXT2030AA, UXT2036AA User Manual
Range Hood - 30" (76.2 cm) and 36" (91.4 cm)
PRODUCT MODEL NUMBERS
PRODUCT DIMENSIONS
UXT2030AA UXT2036AA
Electrical:
●
A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical
circuit is required.
●
If the house has aluminum wiring, follow the
procedure below:
1. Connect a section of solid copper wire to the pigtail
leads.
2. Connect the aluminum wiring to the added section
of copper wire using special connectors and/or tools
designed and UL listed for joining copper to
aluminum.
●
Follow the electrical connector manufacturer's
recommended procedure. Aluminum/copper
connection must conform with local codes and
industry accepted wiring practices.
●
Wire sizes and connections must conform with the
rating of the appliance as specified on the model/serial
rating plate. The model/serial plate is located behind
the filter on the rear wall of the range hood.
●
Wire sizes must conform to the requirements of the
National Electrical Code, ANSI/NFPA 70 (latest edition),
or CSA Standards C22. 1-94, Canadian Electrical Code,
Part 1 and C22.2 No. 0-M91 (latest edition) and all
local codes and ordinances.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10133060
03-26-10
CABINET DIMENSIONS
Rear of hood
Centerline
Centerline
Wiring knockouts
12"
6"
17 ⁵⁄₈"
³/₄"
7¹⁄₂"
5 ³⁄₄"
7" (17.8 cm)
Round vent
(30.5 cm)
(14.6 cm)
(15.2 cm)
(19.1 cm)
2"
(5.1 cm)
(19.1 cm)
(44.8 cm)
29
⁷⁄₈"
(75.9 cm)
35
⁷⁄₈"
(91.1 cm)
VENTING REQUIREMENTS
D
Vent system can terminate either through the roof or wall. Use a 7" (17.8 cm) round vent
with a maximum length of 26 ft (7.9 m) for vent system.
LOCATION REQUIREMENTS
IMPORTANT: Observe all governing codes and ordinances.
●
It is the installer's responsibility to comply with installation clearances specified on the
model/serial rating plate. The model/serial rating plate is located inside the range hood
on the rear wall.
●
Range hood location should be away from strong draft areas, such as windows, doors
and strong heating vents.
●
Cabinet opening dimensions that are shown must be used. Given dimensions provide
minimum clearance. Consult the cooktop/range manufacturer installation instructions
before making any cutouts.
●
Grounded electrical outlet is required. See “Electrical Requirements” section.
●
The range hood is factory set for venting through the roof or wall.
●
All openings in ceiling and wall where range hood will be installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the Manufactured Home Construction
Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable,
the standard for Manufactured Home Installation 1982 (Manufactured Home Sites,
Communities and Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local codes.
Page 1 of 2
30" (76.2 cm)
36" (91.4 cm)
cabinet opening width
18" (45.7 cm) min.
24" (61.0 cm)
suggested max.
bottom of range hood
to cooking surface
13" (33 cm)
cabinet depth
18" (45.7 cm)
min. clearance
upper cabinet
to countertop
36" (91.4 cm)
base cabinet
height
Vertical Roof Venting Horizontal Wall Venting
A
B
D
A
B
C
C
A. 7" (17.8 cm) round through roof
B. Round vent: Use 7" (17.8 cm)
round damper.
C. 18" (45.7 cm) to 24" (61.0 cm)
above cooking surface
D. Roof cap
A. 7" (17.8 cm) round through
the wall
B. Round vent: Use 7" (17.8 cm)
round damper.
C. 18" (45.7 cm) to 24" (61.0 cm)
above cooking surface
D. Wall cap
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10133060
03-26-10
Page 2 of 2
Calculating Vent System Length
To calculate the length of the system you need, add the equivalent feet
(meters) for each vent piece used in the system.
7" (17.8 cm) Vent System
Vent Piece 7" (17.8 cm) Round
45° elbow 2.5 ft
(0.8 m)
90° elbow 5.0 ft
(1.5 m)
7" (17.8 cm) 0.0 ft
wall cap (0.0 m)
3¹⁄₄" x 10" (8.3 cm x 25.4 cm) 4.5 ft
to 7" (17.8 cm) (1.4 m)
3¹⁄₄" x 10" (8.3 cm x 25.4 cm) 5.0 ft
to 7" (17.8 cm) 90° elbow (1.5 m)
7" (17.8 cm) to 3¹⁄₄" x 10" 9.0 ft
(8.3 cm x 25.4 cm) 90° elbow (2.7 m)
Example vent system
Maximum Length = 26 ft (7.9 m)
1 - 90° elbow = 5.0 ft (1.5 m)
1 - wall cap = 0.0 ft (0.0 m)
8 ft (2.4 m) straight = 8.0 ft (2.4 m)
Length of 7" (17.8 cm) system = 13.0 ft (3.9 m)
90˚ elbow
2 ft (0.6 m)
6 ft (1.8 m)
Wall cap
Loading...