Whirlpool PVWN600 Series, PVWC600 Series, PVWM600 Series, PVWS600 Series, PVBN600 Series Installation Instructions Manual

Tip Over Hazard

Do not use clothes vitalizer until
completely installed.
Install lag bolts securely into wall

studs.
Use two or more people to move

and install clothes vitalizer.
Failure to follow these

instructions can result in death or

serious injury.

Paff No, 8527279

IMPORTANT:

Read and save

these instructions.

IMPORTANT:
Installer: Leave Installation Instructions

with the owner.

Owner: Keep Installation instructions for

future reference.

Save: Installation Instructions for local

electrical inspector's use.

TM

www.personalvalet.com Trademark of Whirlpool, U.S.A.

Before you start...

Your safety and the safety of

others are very important.

Ne have provided many important
safety messages in this manual
and on your appliance. Always

read and obey all safety messages.

This is the safety alert

symbol.
This symbol alerts you to

potential hazards that can kill or
hurt you and others.

All safety messages will follow the

safety alert symbol and either the
word "DANGER" or "WARNING".

These words mean:

You can be killed or seriously

injured if you don't immediately

follow instructions.

You can be killed or seriously

injured If you don't follow
instructions.

All safety messages will tell you
what the potential hazard is, tell you
how 1oreduce the chance of injury,

and tell you what can happen if the
instructions are not followed.

It isyour ..

responsibdRyto:

Observe all governing codes and
ordinances.

Check code requirements: Some

codes limit or do not permit

installation of this product in garages,

closets, mobile homes or sleeping

quarters. Contact your local building

inspector.
Comply with the installation

specifications and dimensions.
Consider spacing requirements for

companion appliances.

Make sure you have everything

necessary for proper installation.
Properly install appliance.

Contact a qualified installer to insure
that the electrical installation meets
all national and local codes and

ordinances.

PAGE 2

Electrical

requirements

Electrical Shock Hazard

Plug into a grounded 3-prong
outlet.

Do not remove ground prong.
Do not use an adapter.

Do not use an extension cord.
Failure to follow these

instructions can result in death,
fire, or electrical shock.

4

Important: Observe all governing
codes and ordinances.

A 120-volt, 60-Hz, AC-only, 15- or
20-ampere fused electrical supply is

required. A Time-delay fuse or circuit
breaker is recommended,

It is recommended that a separate
circuit serving only this appliance be

provided.

If codes permit and a separate
ground wire is used, it is

recommended that a qualified
electrician determine that the

ground path is adequate.

3-prong ground-type outlet must

be located within 5 feet of lower
right corner of appliance.

Recommended

ground method

The clothes vitalizer, when installed,

must be electrically grounded in

accordance with local codes, or in

the absence of local codes, with
National Electrical Code, ANSI/
NFPA 70".

GROUNDING INSTRUCTIONS: This
clothes vitalizer must be grounded. In

the event of malfunction or

breakdown, grounding will reduce the

dsk of electdc shock by providing a
path of least resistance for electric

current.

The power supply cord plug must be

plugged into an appropriate outlet

that is properly installed and
grounded in accordance with all local

codes and ordinances.
WARNING - Improper connection

of the equipment-grounding
conductor can result in a risk of

electric shock. Check with a
qualified electrician or serviceman

if you are in doubt as to whether
the appliance is properly
grounded. Do not modify the plug

provided with the appliance - if it

will not fit the outlet, have a proper

outlet installed by a qualified
electrician.

3-prong goutlet

ground ^ A

plug __

r / ground

/ prong

power

suppty

cord

Tools needed for

installation:

• stud finder (optional)

• drill (electric recommended)

• 5/32" drillbit (pilot hole for lag bolt)

• tape measure

• pencil

• carpenter's level

• 7/16" wrench (ratchet

recommended) for lag bolts

if installing on a concrete or concrete

block wall

• concrete ddll bit for wall anchors

(refer to wall anchor for drill bit size)

• hammer

Parts supplied for
installabon:

(inside accessory box)

• 2, 1/4" x 2" lag bolts (for wood studs)

• 2, 1/4-20" nuts

• 1 mounting bracket cover (can be
painted or covered with wallpaper)

• separate metal mounting bracket
assembly

• 6, 1/8=thick adhesive backed cabinet
spacers

Copies of the standards listed above may be
obtained from:

• National Fire Protection AasodalJon

One Batterymardn Park
Quincy, Massachusetts 02269