Whirlpool FL 1289 INSTRUCTION FOR USE

GB PROGRAMME CHART
A. “Door open” indication This washing machine is equipped with
automatic safety functions which detect and diagnose faults at an early stage and react appropriately, e.g.:
B. “Service” indication C. “Water tap closed” indication
C D
H
}
E. Programme selector F. “Start” button
A
G. Spin speed selector
B
H. Programme sequence indicator
I
D. “Clean pump” indication
Programme
Cotton
40 - 60 - 95 °C
Synthetics
30 - 40 - 60 °C
Delicates
30 - 40 °C
Daily load
40 °C
Quick wash
30 °C
Wool
Cold - 40 °C
Handwash
30 - 40 °C
Coton
40 - 60 - 95 °C
Synthétiques
30 - 40 - 60 °C
Délicat
30 - 40 °C
Rapide 30min.
Laine
Froid - 40 °C
Lavage main
30 - 40 °C
40 °C
30 °C
Care
Max. Load
- For temperature selection, respect the manufacturer’s recommendations on the care label
kg
Normally to heavily soiled bed linen, table linen and underwear, towels,
8.0
shirts etc. made of cotton and linen. Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen,
3.0
Trevira), polyamide (Perlon, Nylon) or blends with cotton.
With heavily soiled laundry the “Prewash” option can be additionally selected.
Curtains and delicate clothing, dresses skirts, shirts and blouses.
1.5
With heavily soiled laundry the “Prewash” option can be additionally selected.
4.0 Slightly to normally soiled textiles made of cotton and/or synthetics. Yes
Shortly worn outer clothing made of cotton, polyester, polyamide and
4.0
blends with cotton. Only woollens, labelled with the Woolmark and identified as machine
1.0
washable.
If you select “Rinse Hold” do not leave items to soak for too long.
Textiles made of linen, silk, wool and viscose marked as “handwashable”.
1.0
If you select “Rinse Hold” do not leave items to soak for too long. A very gentle spin is used in this programme.
Type of wash/Notes
Detergents and additives Special options
Pre-
Main
wash
Wash
—Yes
—Yes
—Yes
FGE
Softener Start
Yes
❉❉❉❉❉❉❉
Yes
❉❉❉❉❉❉❉
Yes
❉❉—❉
❉❉
❉❉
❉❉
❉❉
I. “Reset” button
delay
Eco
Eco
lavage
——
—— —
—— —
—— —
Pre-
wash
Pré-
Intensive
rinse
Rinçage intensif
❉❉❉
Rinse
Variable
hold
spin
Arrêt
Essorage
cuve
variable
pleine
❉❉
❉❉
❉❉
❉❉
Max.
Spin
Speed
rpm
max.
max.
1000
max.
max.
1000
400
1)
1)
2)
Rinse & Spin Rinçage & Essorage 8.0 Same as the last rinse and the final spin in the “Cotton” programme. ——
Spin Essorage 8.0
Gentle Spin Essorage court 1.0
Drain Vidange
❉: = optional / Yes = dosing required.
1)
For improved garment care, spin speed is restricted to 1000 rpm in this programme.
2)
For improved garment care, spin speed is restricted to 400 rpm in this programme.
In this programme spinning is intensive. Same as the spin cycle in the “Cotton” programme.
In this programme spinning is gentle. Same as the spin cycle in the “Wool” programme.
Drain only - no spinning. Alternative method of terminating programme after “Rinse Hold”.
———
———
———
❉❉
——
—— — —
—— — —
—— — — —
❉❉❉
max.
max.
1000
1)
5019 601 05058
CONSUMPTION DATA
Programme
Cotton 95 8.0 82* 2.40 2:10 Cotton** 60 8.0 59 1.36 3:30
Cotton 40 8.0 77 0.75 2:05 Synthetics 60 3.0 46* 0.80 1:35 Synthetics 40 3.0 42 0.40 1:20
Delicates 30 1.5 60 0.50 0:45
Daily load 40 4.0 48 0.50 1:00
Quick wash 30 4.0 48 0.25 0:30
Wool 40 1.0 60 0.55 0:45
Handwash 40 1.0 45 0.55 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out. ** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE PROGRAMME
Add detergent as indicated on the front page and as described in the chapter “Detergent and Additives” in your Instructions for Use.
• Turn the programme selector to the desired programme and
• The indication lamp next to the “Start” button blinks.
•The indication lamp of the predefined spin speed lights up.
Handwash 30 1.0 45 0.45 0:36
temperature.
Temperature
(°C)
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the respective indication lights up.
When the combination of programme and additional option(s) is not possible, the indication lights switch off automatically. Unsuitable combinations of options are deselected automatically.
“Eco” button
• With a modified temperature profile and a prolonged programme duration, the optimum combination of good washin g result and lower energy consumption is achieved.
“Prewash” button
• Only for heavily soiled loads (for example sand, granular dirt) sensible. Increases the cycle time by approximately 15 min.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very soft water, washing baby linen and helping people with allergies.
Load
(kg)
Water
Energy
(l)
“Rinse hold” button
• The laundry remains in the last rinse water without progressing
• This option is particularly recommended for the programmes
• It is particularly useful if you want to postpone spinning to a later
Terminate the “Rinse hold” option:
• Press the “Start” button ; the programme will
• If you do not wish to spin the clothes, tur n the progr amm e
“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is cancelled but
(kWh)
to the final spin cycle to avoid creasing and prevent colours from changing.
“Synthetics”, “Daily load” and “Delicates”.
time, or if you want to drain only.
Note: The programme stops to “Rinse hold” at the time the “Rinse hold” light in the programme sequence indication is on. The indication lamp next to the “Start” button blinks.
terminate automatically with the final spin cycle for the present wash programme.
selector to the “Drain” programme and press the “Start” button
.
intermediate spin peaks remain during rinse. The water is drained out only.
Approx. Programme Duration
(hours : minutes)
START DELAY
The “Start delay” allows to run the machine at the consumer’s convenience, for example at night when electricity is cheaper.
• Select programme, temperature and options.
• Press the “Start delay” button to select the delay time by 1, 3, 6, 9 or 12 hours.
•Press the “Start” button . The indication light next to the “Start delay” button lights up and the countdown of the delay time begins.
• The time delay indication disappears when the programme starts and it is replaced by the remaining programme time.
• Once having pressed the “Start” button , the number of hours preselected can be reduced by pressing again the “Start delay” button.
To cancel the “Start delay”
...before you press the “Start” button :
• Turn the programme selector to another position or press the
“Reset” button.
...after having pressed the “Start” button :
•Press the “Reset” button for at least 3 seconds - the start delay time disappears from the time display.
PROGRAMME START
Open the tap and press the “Start” button . The in dication lamp next to the “Start” button lights up. The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Spin/Drain.
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp lights to show that the door can be opened. As long as a wash programme is running, the door remains locked and must on no account be forced open. In case you have an urgent need to open it during a running programme, refer to “Cancel (Reset) a running programme before the end”.
RED INDICATIONS
“Service”
Lighting up of the “Service” indication can be caused by a fault in an electrical component. Refer to the “ Troublesh ooting Gu ide” in your Instructions for Use; if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open the water tap; if the indication still lights up, refer to the “Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain hose is kinked or the filter must be cleaned; in the latter case refer to the Instructions for Use (“Removing the Filter”).
PROGRAMME END
• All the lights of the programme sequence indicator are off, and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START
1. Press the “Start” button to pause the programme. The light blinks.
2. Select the new programme and, if you want, another spin speed and any options.
3. Press th e “Start” button again. The new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this progra mm e.
CANCEL (RESET) A RUNNING PROGRAMME BEFORE THE END
The “Reset” button cancels a programme before the end.
• Press the “Reset” button for at least 3 seconds. Any existing water is drained out before the door can be opened.
5019 601 05058
Loading...