Whirlpool ADP 2645 WH INSTRUCTION FOR USE
GB
ADP 2645
Further indications are given in the pages to follow and in the user instructions.
Programme selector
Start button
Indicator lamp lit while the dishwasher is operating.
Flashes when a fault occurs.
Switches off at the end of the programme.
Quick Reference Guide
Option
Rinse aid level indicator
Add rinse aid.
Salt level indicator
Add regeneration salt; only add
regeneration salt immediately before
starting a wash programme.
Programme Symbol
and Temperature
Pre-wash
Rapid 40° C
Bio Eco 50° C
Universal 65° C
Normal 65° C
Intensive 70° C
1) Values may vary in relation to usage, e.g.: different loads, water
temperatures - above or below 15° C - as well as water hardness and power supply voltage, etc.
2) Programme recommended when using detergents of type B (enzyme-based detergents).
Reference programme for energy label.
3) Programme recommended when using detergents of type A (non enzyme-based detergents).
Crockery to be washed later.
Lightly soiled crockery with no dried-on food.
2)
Normally or heavily soiled crockery with dried-on food.
Normally soiled crockery.
3)
Normally or heavily soiled crockery.
Heavily soiled pans and saucepans.
Programme selection and
recommended load type
Place the detergent in the:
small large
compartment compartment
- - 5.0 0.02 9
- X 13.0 0.85 30
X X 16.0 1.26 133
- X 14.0 1.50 73
X X 16.0 1.60 86
X X 22.5 1.75 93
Water
(Litres)
Consumption
Normal load
Energy
(kWh)
5019 100 91274
(We reserve the right to make technical modifications)
1)
Time
(Min.)
A
C
D
How to use the dishwasher
1. After loading the dishwasher, close the
door properly and open the water
supply tap.
2. The dishwasher switches on
automatically as soon as the
programme selector knob is turned.
One of the programme indicator
lamps will switch on.
3. Turn the selector knob to select the
desired programme.
indicator lamp lights up.
select options (if supplied).
4. Press the Start button to start the
selected programme.
corresponding indicator lamp
switches on.
programmed data cannot be altered by
turning the programme selector knob.
once the Start button has been
Note:
pressed, the dishwasher memorises the
last programme selected. This
information remains in the memory even
during interruption of the power supply.
To change the selected
programme, press the Start button
for about 5 seconds
Start indicator lamp switches
Select a new programme and
off.
press the Start button.
if the dishwasher is switched off
Note:
during a wash programme, when
switched on again it will resume the
wash cycle from where it was
interrupted.
Only open the dishwasher door if
strictly necessary during a wash
cycle and exercise maximum
caution. Danger of scalding from
5. To indicate the end of the programme,
steam.
the Start indicator lamp switches off
and
the End indicator lamp (if fitted)
lights up
(for about 30 min.)
The corresponding
If required,
The
Once set, the
, until the
.
6. Once the Start indicator lamp has
switched off, turn the programme
selector knob to the initial position to
switch off the dishwasher.
indicator lamps switch off.
7. Open the door (warning: beware of hot
steam). Unload the lower rack before
the upper one. Close the water tap.
All the
Upper rack
Rack height adjustment:
(The dishwasher is delivered with the upper
rack in the top position).
The rack height can also be changed
when loaded.
• To lower: pull out the
handles and gently lower the rack.
two
side
Upper and lower rack
• To raise: pull up the
handles until the rack clicks into
place.
• The rack must be level on both
sides.
Crockery holders:
• Down: cups and long-stemmed
glasses.
•
Up: plates.
Glass holder:
two
side
Lower rack
A
A
C
Plate holders:
•(A) May be lowered to increase
available space.
Cutlery basket:
• The cutlery basket can be removed
to increase (C) available space.
• Some models are provided with
a grid (D) that can be fitted onto
the cutlery basket.
Please read the user instructions carefully.
Loading...