Whirlpool ADG9999 User Manual

Quick reference guide

Chart

FAULT INDICATION AND WASH TIME DISPLAY

In normal operation it indicates the remaining time (h:mm), whereas with “Delayed start” selected it indicates the time remaining until programme start (hh).

BUTTON

If “F..” appears on the display, see chapter “What to do if...”.

OFF

PROGRAMME SELECTION BUTTON

Press button “P” (repeatedly) until the required programme number appears on the display (see “Table of programmes” below).

RESET BUTTON For programme change or indication of faults.

Press this button to cancel a started programme and selected extra options. Press this button to cancel the main fault indicators “F..” also refer to the chapter “What to do if...”. The programme can then be selected and started.

Table of programmes

50°C

Available

options

Multizone

Power Clean

Multizone

Power Clean

Multizone

Power Clean

Multizone

Loading instructions

Normally or heavily soiled crockery,

Delay

including pots and pans. Thanks to ste am action, soaking or hand pretreatment is no longer needed. In addition hygiene is ensured due to the high temperature steam.

Delay

Crockery to be washed later. — 4.0 0.03 14

Delay

Light soiling, for example glasses and cups. X 10.0 0.85 100

Lightly soiled crockery, with no dried-on

Delay

food.

Not recommended tablets use.

Delay

Normally soiled crockery. Energy-saving programme.

Normally or heavily soiled crockery, with

Delay

additional antibacterial wash. Programme interruption (e.g. due to door o pening) can compromise elimination of germs.

Normally soiled crockery, gentle and q uiet

Delay

thanks to the lower spray pressure (39dbA).

4 5

1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of the appliance’s automatic calibration system.

2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.

Programmes

Aqua Steam 40-70°C

Pre-Wash cold

Glasses 40°C

Quickwash 45°C

Eco

Antibacterial

Overnight 55°C

START BUTTON

The indicator lights up during operation, flashes when a fault occurs and goes off at the end of the programme.

(see at right for options description)

Consumption

Deter-

gent

Litres Kwh

X 7-15 0.99-1.75 65-205

11.0 0.80 30

X 11.0 0.98 170

X 13.0 1.50 115

X 13.0 1.20 290

Minutes

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS! THE GUARANTEE IS NOT APPLICABLE IF FAULTS ARE CAUSED BY INCORRECT USE OF THE APPLIANCE.

Options and display description

SALT INDICATOR

When lit, the salt reservoir needs to be refilled.

SET THE DETERGENT

Press this button (repeatedly) to set the type of detergent used.

Powder, gel (standard)

Detergent with rinse aid

Detergent with salt + rinse aid

RINSE AID INDICATOR

When lit, the rinse aid dispenser needs to be refilled.

HALF LOAD/ MULTIZONE

Allows you to choose the washing zones. Press this button (repeatedly) to select the wash zones:

both racks

only upper rack

only lower rack

POWER CLEAN

Thanks to the additional power jets this option provides a more intensive and powerful wash in the lower rack, in the specific area. This option is recommended for washing pots and

(see

casseroles

page 4)

. Press this button to activate Power Clean (the indicator lights up).

5019 396 01808ADG 9999

DELAYED START BUTTON

Press the button (repeatedly) to delay the start of the programme. Adjustable from 1 to 24 hours. With each press of the button, the delayed start indicator increases by one hour and after 24 resets from 00. Then press the START button. The dishwasher will start after the set time.

-1-

How to set water hardness in order to always assure the best cleaning results

before the first wash

only

Switch on the appliance

- Select the 2nd programme “P2” - consult the table of programmes.

- Press the START button fo r at least 5 seconds until the START indicator lamp flashes.

- The water hardness setting is shown on the display (if present) or the START button flashes.

- With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again.

- The appliance must be switched off to memorise the new setting.

water hardness has been changed

or if the

First time use

1- salt reservoir 2- rinse aid dispenser 3- detergent dispenser 4- racks system 5,6,7,8- available functions on the panel 9- filters 10- spray arms

Ask your water supply company what the

hardness

is...

German

degrees °dH

0 - 5 0 - 9 0 - 6.3 Soft 1 1x

6 - 10 10 - 18 7 - 12.6 Medium 2 2x 11 - 15 19 - 27 13.3 - 18.9 Average 3 3x 16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4 4x 22 - 28 38 - 50 26.6 - 35 Hard 5 5x 29 - 35 51 - 63 35.7 - 44.1 Very hard 6 6x

36 - 60 64 - 107 44.8 - 74.9

French

degrees °fH

degrees °eH

Filling the salt reservoir -

Visual indicator (depending

English

water

hardness

Extremely

Water

hard

...enter this value on your dishwasher

Dishwasher

with display:

insert value in

the display

7 7x

Dissolve limescale (not necessary if water hardness level is set to “soft”!)

on model). Unscrew cap.

Fill the salt reservoir with water before the first wash only .

The salt level indicator lamp may remain lit for the duration of several wash cycles. If the water hardness level falls within category (soft), no salt is required.

Salt indicator (depending on the model)

Suggestions for detergent use

Dishwasher

without

display: count

START button

led flashes

Gel or Powder

(rinse aid and

salt)

go to step 1

(see “Daily

check”)

Tablets

if extra salt is needed go to

step 1

(see “Daily

check”)

Add salt

(never add detergent!). min. 1.5 kg max. 2 kg

The indicator lamp on the control panel lights up when SALT NEEDS TO BE ADDED.

Water hardness level is factory set for medium hard water (a number “4” is shown on the display or the START indicator lamp flashes 4 times).

Even if you use tablets which include salt, you must still add salt since such detergents are not effective enough at softening hard water.

Daily check

Visual indicator (depending on model). Screw on the cap. Salt residues around cap need to be removed.

orange: OK.

clear: NEEDS TO BE ADDED

-2-

Adding rinse aid

(not necessary when you use tablets). How to adjust the rinse aid dosage regulator

Daily check

Rinse aid indicator (depending on model)

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.

If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programmes. In the case of shorter programmes, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.

Adding detergent -

Visual indicator

If required, open the cover B (press right button).

The indicator lamp on the control panel lights up when RINSE AID NEEDS TO BE ADDED.

Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations

Open the cover A (press left button).

Only fill the detergent dispenser prior to starting a wash programme.

Add rinse aid to the max. line ~150 ml

Tablet / gel / powder

Use only one tablet per one cycle, only placed in detergent dispenser.

All types of tablets can be used, but for 2 in 1 type adding of salt is mandatory.

The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.

dark: OK. clear: NEEDS TO BE ADDED

Daily use

By pressing dedicated ribs shut the cover.

-3-

+ 5 hidden pages