Quick reference guide |
Chart |
PROGRAM |
START BUTTON |
AND DELAY |
The indicator lights up during operation, flashes when a fault occurs, and goes off at the end of the program. |
SELECTOR |
START BUTTON RESET FUNCTION: |
KNOB |
Press this button for at least 2 seconds; the selected program and options will be cancelled. Main failure |
(see at right for |
displays (repeated flashing of the START indicator lamp) can be cancelled by RESETTING. Detailed |
options description |
instructions are given in chapter “What to do if...”. |
and “Table of |
|
programs” below). |
|
BEFORE USING THE APPLIANCE FOR THE
FIRST TIME CAREFULLY READ THIS QUICK
REFERENCE GUIDE AND THE ASSEMBLY
INSTRUCTIONS! THE GUARANTEE IS NOT
APPLICABLE IF FAULTS ARE CAUSED BY
INCORRECT USE OF THE APPLIANCE.
Options and display description
program settings |
|
Start delay and |
ON/OFF without start delay |
|
program settings |
BUTTON |
|
|
1 |
Switch on the appliance |
1 |
|
- press the ON/OFF button. |
|
|
OK/Start lamp flashes. |
|
|
Table of programs |
Deter- |
Consumption |
|||||
|
|
|
|
|
|
|
|
|
P |
programs |
|
Available |
Loading instructions |
gent |
Litres |
kWh |
Minutes 1) |
|
options |
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
Pre-Wash |
cold |
Delay |
Crockery to be washed later. |
— |
4.0 |
0.03 |
14 |
|
|
|
|
|
|
|
|
|
2 |
Quickwash |
45°C |
|
Lightly soiled crockery, with no |
|
|
|
|
Delay |
dried-on food. * Use of tablets |
X * |
11.0 |
0.80 |
30 |
|||
|
|
|
|
not recommended. |
|
|
|
|
|
|
|
|
|
|
|
|
|
3 |
Eco 2) |
50°C |
Delay |
Normally soiled crockery. Energy- |
X |
12.0 |
1.05 |
170 |
saving program. |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
Normally or heavily soiled crockery, |
|
|
|
|
4 |
Antibacterial 3) |
Delay |
with additional antibacterial wash. |
X |
13.0 |
1.50 |
115 |
|
program interruption (e.g. due to |
||||||||
|
|
|
|
door opening) can compromise |
|
|
|
|
|
|
|
|
elimination of germs. |
|
|
|
|
|
|
|
|
|
|
|
|
|
5 |
Intensive |
70°C |
Delay |
Recommended program for |
X |
14.0 |
1.55 |
155 |
heavily soiled crockery, especially |
||||||||
|
|
|
|
suitable for pots and pans. |
|
|
|
|
|
|
|
|
|
|
|
|
|
1)Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.
2)Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3)The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
2
3
Set the desired start delay (3-6-9h). The |
2 |
|
|
|
|
selected start delay lamp (3-6-9h) |
|
|
|
|
|
flashes. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Press the OK/Start button for |
|
3 |
|
|
|
|
|
|
|
||
|
|
|
|
||
confirmation. After that the OK/Start |
|
|
|
|
|
lamp switches off and the selected start |
|
|
|
|
|
|
|
|
|
|
|
delay lamp lights up. |
|
|
|
|
|
If you wish another time setting, press |
|
|
|
|
|
OK/Start button again. |
|
|
|
|
|
Turn the program knob to your desired |
4 |
|
|
|
|
program position. |
|
|
|
|
|
The OK/Start lamp flashes. |
|
|
|
|
|
Press the OK/Start button for |
5 |
|
|
|
|
confirmation. |
|
|
|
|
|
After that the OK/Start lamp lights up. The dishwasher starts immediately or after the start delay selected.
For a Reset, press the OK/Start button at a minimum of 2 seconds.
All settings are cancelled. Indication: In the selection mode, all described settings have to be selected within 30 seconds, otherwise no settings will be saved.
ADG 674 5019 396 01906
GB -1-
How to set detergent type: powder/gel/tablet (if option is available) |
First time use |
In order to always ensure the best cleaning results, you NEED to set:
DETERGENT type and WATER HARDNESS.
1. Select 3rd program (see |
2. Press START button |
3a. Check your |
3b....and set it on your dishwasher |
4. Remember to use salt and rinse |
5. Switch off and switch on |
Table of programs - page 1) |
for 7 seconds |
detergent type... |
using the START button |
aid when needed (as indicated |
again to save setting |
|
|
|
(as per table below) |
below) |
|
Dishwasher models
Detergent |
model without |
|
|
|
|
types |
model with display |
|
|
||
|
display |
|
|
||
|
|
|
|
||
Powder or gel |
3h 6h 9h |
no symbol |
add salt |
add rinse aid |
|
(factory setting) |
|||||
|
|
|
|
||
Tablet 2 in 1 |
|
|
add salt |
rinse aid |
|
Tablet 3 in 1 |
|
|
|
|
|
|
|
|
salt |
rinse aid |
|
Tablet All in 1 |
|
|
|
|
For models without “detergent type” option, the salt and rinse aid indicators will be lit when tablets are used.
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10spray arms
How to set water hardness
* only before the first wash or if the water hardness has been changed
Switch on the appliance
-Select the 2nd program “P2” - consult the table of programs.
-Press the START button for at least 5 seconds until the START indicator lamp flashes.
-The water hardness setting is shown on the display (if present) or the START button flashes.
-With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again.
-The appliance must be switched off to memorise the new setting.
Water hardness level is factory set for medium hard water (a number “4” is shown on the display or the START indicator lamp flashes 4 times).
Even if you use tablets which include salt functionality, you must still add salt since such detergents are not effective enough at softening hard water.
At first time use, the salt reservoir has to be filled independently from water hardness level (see description in step 1 “Daily check”).
1. Ask your water supply company what the water hardness is... |
2. ...enter this value on your |
Suggestions for detergent use |
||||||||
|
|
|
|
|
|
dishwasher |
|
|
|
|
|
|
|
|
|
|
Dishwasher |
Dishwasher |
|
|
|
|
|
|
|
|
|
without |
Gel or Powder |
|
||
German |
French |
English |
Water |
with display: |
|
|||||
display: count |
(rinse aid and |
Tablets |
||||||||
degrees °dH |
degrees °fH |
degrees °eH |
hardness |
insert value in |
||||||
START button |
salt) |
|
||||||||
|
|
|
|
|
|
the display |
|
|||
|
|
|
|
|
|
led flashes |
|
|
||
|
|
|
|
|
|
|
|
|
||
0 |
- 5 |
0 |
- 9 |
0 - 6.3 |
Soft |
1 |
1x |
|
|
|
|
|
|
|
|
|
|
|
|
||
6 - 10 |
10 |
- 18 |
7 - 12.6 |
Medium |
2 |
2x |
|
|
||
|
|
|
|
|
|
|
|
|
if extra salt is |
|
11 |
- 15 |
19 |
- 27 |
13.3 - 18.9 |
Average |
3 |
3x |
|
||
|
|
|
|
|
|
|
|
go to step 1 |
needed go to |
|
16 |
- 21 |
28 |
- 37 |
19.6 - 25.9 |
Medium-hard |
4 |
4x |
|||
(see “Daily |
step 1 |
|||||||||
22 |
- 28 |
38 |
- 50 |
26.6 - 35 |
Hard |
5 |
5x |
check”) |
(see “Daily |
|
|
|
|
|
|
|
|
|
|
check”) |
|
29 |
- 35 |
51 |
- 63 |
35.7 - 44.1 |
Very hard |
6 |
6x |
|
||
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
36 |
- 50 |
64 |
- 90 |
44.8 - 62.4 |
Extremely |
7 |
7x |
|
|
|
hard |
|
|
||||||||
|
|
|
|
|
|
|
|
|
GB -2-
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)
Daily check
1 |
Visual indicator |
Fill the salt reservoir |
|
(depending |
with water before the |
|
on model). |
first wash only. |
|
Unscrew cap. |
|
Add salt
(never add detergent!). min. 0.8 kg
max. 1 kg
Screw on the cap. Salt residual around the cap need to be removed. Some salt reservoir have a level indicator integrated in the cap (see below how to check).
(depending on the model) |
|
Salt indicator on the control panel |
Salt indicator on the salt reservoir cap |
The salt level indicator lamp may remain lit for the duration of several wash cycles. If the water hardness level falls within category (soft), no salt is required.
The indicator lamp lights up when SALT NEEDS TO BE ADDED. |
green: OK. |
clear: NEEDS TO BE ADDED |
Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator
2 |
Visual |
|
|
|
indicator |
If required, open the cover B (press the dedicated button).
Add rinse aid to the max. line ~150 ml
The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.
|
(depending on the model) |
|
|
|
|
|
Check the rinse aid indicator to check the level into the |
Rinse aid indicator on the control panel |
Rinse aid indicator on the dispenser |
|
|
||
|
|
|
|
|
|
|
dispenser. |
The indicator lamp lights up when RINSE AID NEEDS TO BE ADDED. |
|
|
dark: OK. |
|
clear: NEEDS TO BE ADDED |
|
|
|
|
|||
|
|
|
|
|
|
|
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation. Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.
Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Insert detergent: Tablet / powder / liquid into the big chamber
3 |
Open the cover A |
Only fill the |
|
(press the dedicated |
detergent dispenser |
|
button). |
prior to starting a |
|
|
wash program. |
Use only one tablet per one cycle, only placed in detergent dispenser.
All types of tablets can be used, but for 2 in 1 type adding of salt is mandatory.
Daily use
Shut the cover by pressing dedicated ribs.
GB -3-