Whirlpool ACM 879 IX, ACM921 WH, ACM 924 WH, ACM 924 IX, ACM 879 WH INSTALLATION INSTRUCTIONS

INSTRUCTIONS FOR USE

INSTALLATION INSTRUCTIONS BEFORE USING THE APPLIANCE PRECAUTIONS AND GENERAL ADVICE ENERGY SAVING TIPS OVEN ACCESSORIES CLEANING AND MAINTENANCE TROUBLESHOOTING GUIDE AFTER-SALES SERVICE

For best use of the oven, carefully read the operating instructions and keep them for future consultation.

INSTALLATION INSTRUCTIONS

Electrical connection

Before connecting the appliance, make sure:

the mains voltage in your home matches that specified on the appliance dataplate;

the electrical system adequate for appliance max. power absorption specified on the dataplate;

the house electrical system is suitably earthed.

• Connect the appliance to the power supply by means of a suitable disconnecting switch with min. contact opening distance allowing complete disconnection in category III overvoltage conditions, in compliance with the installation regulations.

After installation, the electrical components must only be accessible with the use of a special tool.

Notes:

The power cable must be H05VV-F type and electric connections must be in compliance with below electric information.

3 x 2.5 mm² 220 V ~ 50 Hz 5 x 1.5 mm² 380 V~, 3N 50 Hz 3 x 2.5 mm² 230 V ~ 50 Hz 5 x 1.5 mm² 400 V~, 3N 50 Hz 3 x 2.5 mm² 240 V ~ 50 Hz 5 x 1.5 mm² 415 V~, 3N 50 Hz

Instructions for the installer

Warning

• Disconnect the appliance from the power supply before carrying out any repairs or operation.

• Installation must be carried out by a qualified technician, in compliance with the current safety regulations.

• The appliance must be earthed.

The Manufacturer declines any liability for injury or damage to people or property due to non-compliance with the above-mentioned regulations. The appliance dataplate is located at the bottom right of frame of the oven cavity and visible with the door open. Adjustment conditions are given on a label on the packing. Do not use the oven door for handling operations, or for removing the appliance from the packing.

ELECTRICAL CONNECTION AND SAFETY

For the electrical connection, make sure to follow the instructions given below:

The earth wire must be connected to the earth terminal ( ). If there is no approved earthed

•

electrical outlet in the place where the appliance is to be installed, immediately contact to our Authorised Service.

The earthed electrical outlet must be close to the appliance. Do not use extension cords.

•

The power cable must not touch hot parts of the product.

•

If the power cable is damaged, contact a Qualified Service Centre. The cable must be replaced by the

•

Authorised Service. An incorrect electrical connection could damage your appliance. Such damage is not covered by the

•

warranty. The appliance is arranged for a 230 Volt power supply. If the power supply voltage is different,

•

immediately contact to our authorised service.

The power cable must not touch hot parts of appliance, otherwise it may become damaged. This situation could cause short circuiting. The manufacturer declines any liability for damage and loss due to failure to comply with the following

safety regulations.

Min. 50 cm (depending on the model)

Min. 65 cm

Fig. 1

Installation Important

: The covering of the cabinets must be in heat resistant (min. 90°C) material. If the appliance is installed next to kitchen cabinets, ensure the minimum clearances indicated in the following figure. There are certain points to pay attention to when positioning the cooker. Make sure to take into consideration the following recommendations, in order to prevent any problems and hazardous situations that may occur! The cooker can be positioned near other cabinets provided their height does not exceed the hob level. In selecting a position for the cooker, make sure the appliance is not placed next to a refrigerator and that there are no flammable or combustible materials in the vicinity, such as curtains, etc. which can quickly catch fire. A minimum space of 20 mm between the metal rear cover of the cooker and the wall is required to ensure air circulation.

If the counter tops are higher than hob level, they should be at least 110 mm from the sides of the cooker. To fit them, tilt the appliance and screw the 4 feet in the special threads located in the corners (see Fig. 2).

Connecting the appliance to the power supply

Open the terminal board (see Fig. 3), unscrew the cable clamp screw.

Strip approx. 70 mm. of the cable sheath from the power

•

supply cable Strip approx. 10 mm. of sheath from the conductors

•

Insert the cable into the cable clamp and connect the

•

conductors to the terminal block as indicated in the diagram printed on the label close to the main box Secure the power cable by means of the cable clamp

•

Close and refit the main box plastic cover

•

the yellow-green earth wire must be connected to the

NOTE:

srew with symbol .

Max. adjustment 15 mm

Fig. 2

Fig. 3

+ 6 hidden pages