Whirlpool 8TWFW5620HW0, 8TWFW6620HW0, 8TMHW6630HW0 Installation Guide
WASHER
洗衣機安裝說明
目錄
洗衣機安裝 ......................................................................1
安裝要求 .........................................................................2
工具與零件 ........................................................................2
地點要求 ............................................................................ 3
排水系統 ............................................................................ 4
電氣要求 ............................................................................ 5
安裝說明 .........................................................................5
連接排水管 ........................................................................6
連接進水管 ........................................................................7
放平洗衣機 ........................................................................8
完成安裝檢核清單 ..............................................................9
安裝備註
INSTALLATION
INSTRUCTIONS
Table of Contents
WASHER SAFETY .......................................................10
INSTALLATION REQUIREMENTS ..............................10
Tools and Parts ..............................................................10
Location Requirements ................................................11
Drain System .................................................................12
Electrical Requirements ...............................................13
INSTALLATION INSTRUCTIONS ................................13
Connect Drain Hose ...................................................... 14
Connect Inlet Hoses ......................................................15
Level Washer .................................................................16
Complete Installation Checklist ................................... 17
INSTALLATION NOTES
購買日期： ______________________________________
安裝日期： ______________________________________
安裝人員： ______________________________________
型號： __________________________________________
序號： __________________________________________
洗衣機安裝
㛔℔⎠⛐忁ấㇳℲ冯暣☐ᶲ㍸ὃ姙⣂慵天䘬⬱ℐ㍸䣢ᾉ〗炻婳⊁⽭ᶨᶨ教嬨思⬰ˤ
忁㗗⬱ℐ嬎⏲䫎嘇ˤ
㬌䫎嘇堐䣢⬀⛐⎗傥⮶农ぐㆾṾṢ ṉ䘬㼃⛐⌙晒ˤ
㚱⬱ℐ㍸䣢ᾉ〗䘬⇵悥㚱⬱ℐ㍸䣢䫎嘇ẍ⍲ˬ⌙晒˭ㆾˬ嬎⏲˭⫿㧋ˤ↮⇍ẋ堐烉
危險
警告
Date of purchase: _________________________________
Date of installation: _______________________________
Installer: ________________________________________
Model number: ___________________________________
Serial number: ___________________________________
㚱⬱ℐ㍸䣢ᾉ〗悥㚫⏲姜ぐ㚱⒒ṃ㼃⛐⌙晒ˣ⤪ỽ旵Ỷ⍿ 㨇䌯炻ẍ⍲ᶵ思⬰㊯䣢㚫㚱⒒ṃ⼴㝄ˤ
W11316319B
WASHER SAFETY
INSTALLATION REQUIREMENTS
TOOLS AND PARTS
Gather required tools and parts before starting installation.
Tools needed:
Adjustable or open-end
wrenches 1/2" (13 mm),
5/8" (16 mm) and 9/16" (14 mm)
Ruler or measuring tape
Optional tools:
Flashlight Bucket
Parts supplied:
Level
Pliers that open to
9
1
⁄16" (39.5 mm)
Parts supplied continued:
NOTE: All parts supplied for installation are in the
washer basket.
Cable tie Drain hose with clamp
and form (may be shipped
unassembled)
Transport Bolt Covers
Available accessories:
An optional matching pedestal is available for your washer.
Please contact your retailer for ordering information, or see
the “Assistance or Service” page on the back of your Use
and Care Guide.
Alternate parts (not supplied with washer):
Your installation may require additional parts. To order, please
refer to toll-free numbers on the back page of your Use and
Care Guide.
If you have: You will need:
Overhead sewer Standard 20 gal. (76 L) 39" (990 mm)
tall drain tub or utility sink, sump pump
and connectors (available from local
plumbing suppliers)
Water inlet hoses (2)
Alternate inlet hoses (may be required for some
installations, not supplied with washer)
n
8212656RP
n
8212641RP
n
8212546RP
n
8212545RP
10 ft. (3.0 m) Inlet hose, Black EPDM (2 pack)
5 ft. (1.5 m) Inlet hose, Black EPDM (2 pack)
4 ft. (1.2 m) Inlet hose, Black EPDM (2 pack)
5 ft. (1.5 m) Inlet hose, Red and Blue EPDM
(2 pack)
n
8212487RP
n
8212638RP
5 ft. (1.5 m) Nylon braided inlet hose (2 pack)
6 ft. (1.8 m) Nylon braided inlet hose,
space-saving 90° elbow, hypro-blue steel
couplings (2 pack)
:
LOCATION REQUIREMENTS
Proper installation is your responsibility.
You will need:
n
A water heater set to 120°F (49°C).
n
A grounded electrical outlet located within 6 ft (1.8 m)
of power cord on back of washer.
n
Hot and cold water faucets located within 4 ft (1.2 m) of hot
and cold water ll valves on washer, and water pressure
of 20–100 psi (137.9–689.6 kPa).
n
A level oor with maximum slope of 1" (25 mm) under entire
washer. Installing on carpet or surfaces with foam backing
is not recommended.
n
Floor must support washer’s total weight (with water and load)
of 315 lbs (143 kgs).
IMPORTANT: Do not install, store, or operate washer where it
will be exposed to weather or in temperatures below 32°F (0°C).
Water remaining in washer after use may cause damage in low
temperatures. See “Washer Care” in your Use and Care Guide
for winterizing information.
547/8"
(1393 mm)
319/16"
(802 mm)
385/8"
(981.5 mm)
27"
(686 mm)
* For additional details (or information) specic to your model,
refer to the 'Dimensions' listed for your model at
www.whirlpool.com.tw.
Maytag Models
15
/16"
52
(1345 mm)
3215/16"
(837 mm)
27"
(686 mm)
Whirlpool Models*
1
56
/2"
(1435 mm)
331/4"
(844 mm)
385/8"
(981.5 mm)
27"
(686 mm)
385/8"
(981.5 mm)
5
/16"
51
(1303 mm)
315/16"
(795 mm)
385/8"
(981.5 mm)
27"
(686 mm)
All dimensions show minimum spacing allowed.
For each arrangement, consider allowing more space for ease of
installation and servicing, and spacing for companion appliances
and clearances for walls, doors, and oor moldings.
Space must be large enough to allow door to fully open.
Add spacing of 1" (25 mm) on all sides of washer to reduce
noise transfer. If a closet door or louvered door is installed,
top and bottom air openings in door are required.
Recessed area or closet installation
(stacked washer and dryer):
Custom cabinet installation:
3"
(76 mm)
2
48 in.
(310 cm2)
2
24 in.
(155 cm2)
3"
(76 mm)
0.25"
(5 mm)
Custom under-counter installation:
(1943 mm)
(127 mm)
39" min.
(990 mm)
6"
6"
(152 mm)
(152 mm)
761/2"
5"
1"
(25 mm)
0.25"
(5 mm)
1"
(25 mm)
1"
(25 mm)1"(25 mm)
DRAIN SYSTEM
The drain system can be installed using a oor drain, wall
standpipe, oor standpipe, or laundry tub. Select the method
you need.
IMPORTANT: To avoid siphoning, only 4.5" (114 mm) of drain
hose should be inside standpipe. Always secure drain hose with
cable tie.
Floor standpipe drain system
1"
(25 mm)
27"
(686 mm)
1"
(25 mm)
Recessed area or closet installation:
3"
(76 mm)
2
48 in.
(310 cm2)
2
24 in.
(155 cm2)
3"
(76 mm)
0.25"
(5 mm)
1"
(25 mm)
1"
(25 mm)
(25 mm)1"(25 mm)
4.5"
(114 mm)
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. A 1/4" (6 mm)
diameter to 1" (25 mm) diameter Standpipe Adapter Kit is
available (Part Number 3363920). Top of standpipe must be at
least 39" (990 mm) high; install no higher than 96" (2.44 m) from
bottom of washer. If you have an overhead sewer and need to
pump higher than 96" (2.44 m), a sump pump and associated
hardware are needed. See “Alternate parts.”
Wall standpipe drain system
4.5"
(114 mm)
1"
See requirements for oor standpipe drain system.
Loading...