Whirlpool 7MWET3300EQ0, YMET3800XW1, MET3800XW1, YWET4027EW0, YWET3300XQ2 Installation Guide

...

27" (69 CM) ELECTRIC WASHER/DRYER

INSTALLATION INSTRUCTIONS

INSTRUCTIONS POUR UINSTALLATION DE LA LAVEUSE/

SI CHEUSE I LECTRIQUE DE 27" (69 CM)

Table of Contents Table des mati_res

WASHER/DRYER SAFETY .......................................................... 1

iNSTALLATiON REQUIREMENTS ............................................... 3

Tools and Parts ..................................................................... 3

LOCATION REQUIREMENTS ...................................................... 5

DIMENSIONS/CLEARANCES ..................................................... 6

DRAIN SYSTEM ........................................................................... 7

ELECTRICAL REQUIREMENTS - U.S.A ..................................... 8

ELECTRICAL REQUIREMENTS - CANADA ............................... 9

REMOVE SHiPPiNG STRAP ...................................................... 10

iNSTALL LEVELING LEGS ......................................................... 10

ELECTRICAL CONNECTION (U.S.A. ONLY) ............................ 11

VENTING ..................................................................................... 17

Venting Requirements ........................................................ 17

Plan Vent System ................................................................ 18

Install Vent System ............................................................. 19

CONNECT DRAIN HOSE ........................................................... 20

CONNECT iNLET HOSES .......................................................... 21

CONNECT VENT ........................................................................ 22

LEVEL WASHER/DRYER ........................................................... 23

COMPLETE iNSTALLATiON CHECKLIST ................................ 24

iNSTALLATiON NOTES

Date of purchase: Date of installation:

installer:

Model number: Serial number:

SLeCURITle DE LA LAVEUSE/SECHEUSE ................................ 25

EXIGENCES D'INSTALLATION ................................................. 27

Outillage et pi_ces ............................................................. 27

EXIGENCES D'EMPLACEMENT .............................................. 29

DIMENSIONS/DISTANCES DE DleGAGEMENT ....................... 30

SYSTEME DE VIDANGE ............................................................ 31

SPleClFICATIONS leLECTRIQUES - CANADA ......................... 32

ENLEVER LA SANGLE D'EXPleDITION .................................... 33

iNSTALLATiON DES PIEDS DE NIVELLEMENT ...................... 33

i_VACUATION ............................................................................. 34

Exigences concernant I'_vacuation ................................. 34

Planification du syst_me d'_vacuation ............................ 35

installation du conduit d'_vacuation ................................ 36

RACCORDEMENT DU TUYAU DE VIDANGE ........................... 37

RACCORDEMENT DES TUYAUX D'ARRIVleE D'EAU ............. 38

RACCORDEMENT DU CONDUIT DqeVACUATION ................. 39

leTABLISSEMENT DE L'APLOMB DE

LA LAVEUSE/SI_CHEUSE .......................................................... 40

LISTE DE VERIFICATION POUR L'ACH_:VEMENT

DE L'INSTALLATION .................................................................. 41

NOTES CONCERNANT L'INSTALLATION Date d'achat :

Date d'installation : Installateur :

Num_ro de module : Num_ro de s_rie :

WASHER/DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be kiUed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

W10356098C

WASHER/DRYER SAFETY

WARNING - ofFifo..

- Clothes dryer installation must be performed by a qualified installer, = Install the clothes dryer according to the manufacturer's instructions and local codes.

= Do not install a clothes dryer with flexible plastic venting materials or flexible metal

(foil type) duct. if flexible metal duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will

obstruct clothes dryer airflow and increase the risk of fire,

= To reduce the risk of severe injury or death, follow all installation instructions. = Save these instructions.

iMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer/dryer, follow basic

precautions, including the following:

[] Read all instructions before using the washer/dryer. [] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

[] Do not wash or dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water. These substances give off vapors that could ignite or

explode.

[] Do not allow children to play on or in the washer/dryer.

Close supervision of children is necessary when the

washer/dryer is used near children.

[] Before the washer/dryer is removed from service or

discarded, remove the doors to the washer/dryer compartments.

[] Do not reach into the washer/dryer if the tub, agitator or

drum is moving.

[] Do not install or store the washer/dryer where it will be

exposed to the weather.

[] Do not tamper with controls.

[] Clean dryer lint screen before or after each load.

SAVE THESE INSTRUCTIONS

[] Under certain conditions, hydrogen gas may be produced

in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS iS EXPLOSIVE. ff the hot water

system has not been used for such a period, before using the washing machine, turn on all hot water faucets and let

the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during this time.

[] Do not repair or replace any part of the washer/dryer or

attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair

instructions that you understand and have the skills to carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust, and dirt.

[] The interior of the machine and dryer exhaust vent should

be cleaned periodically by qualified service personnel

[] See "Electrical Requirements" section of the Installation

Instructions booklet for grounding instructions.

INSTALLATION REQUIREMENTS

TOOLS AND PARTS Gather required tools and parts before starting installation.

Tools needed:

Flat-blade screwdriver

Adjustable or open-end wrench 9/16" (14 mm)

4 ='miR

(102 mm)_

Wood block

#2 Phillips screwdriver

Level

Ruler or measuring tape

Optional tools:

Flashlight Parts supplied:

NOTE: Remove parts package from the washer basket. Check that all parts were included.

Front leveling feet with nuts (2) Shipping strap (Not in parts bag.

Bucket

See "Remove Shipping Strap.")

Tin snips (new vent

installations)

1/4" nut driver Wire stripper (recommended)

Caulking gun and compound

(new vent installations)

Adjustable wrench that opens to 1" (25 mm) or

hex-head socket wrench

Utility knife

Drain hose

Silver double-wire hose clamp

INSTALLATION REQUIREMENTS

TOOLS AND PARTS

Parts needed: (Not supplied with washer/dryer)

[] Vent clamps [] Vent elbows and ductwork

Inlet hoses with flat washers

Check local codes, electrical supply and venting, and read "Electrical Requirements" and "Venting Requirements" before purchasing parts. Mobile home installations require metal exhaust system hardware available for purchase from the dealer from whom you purchased your washer/dryer. For further information, please reference the "Assistance or Service" section of the Washer/Dryer Use and Care Guide.

Optional equipment: (Not supplied with washer/dryer) Refer to your Use and Care Guide for information about

accessories available for your washer/dryer.

Alternate parts: (Not supplied with washer/dryer) Your installation may require additional parts. To order, please

refer to toll-free numbers on back page of your Use and Care Guide.

If you have: Overhead sewer

Floor drain

1" (25 mm) standpipe 2" (51 mm) diameter to 1" (25 mm)

Laundry tub or standpipe taller than 96" (2.4 m)

Drain hose too short

Lint clogged drain

Water faucets beyond reach

of fill hoses

You will need:

Standard 20 gal. (76 L) 39" (990 mm) tall Drain Tub or Utility Sink, Sump Pump and Connectors (available from local plumbing suppliers)

Siphon Break Part Number 285320, Additional Drain Hose Part Number

285702, and Connector Kit Part Number 285442

diameter Standpipe Adapter Part Number 3363920, Connector Kit Part Number 285835

Sump pump system (if not already available)

Extension Drain Hose Part Number 285863,

Connector Kit Part Number 285835 Drain Protector Part Number 367031,

Connector Kit Part Number 285835 2 longer water fill hoses:

6 ft (1.8 m) Part Number 76314, 10 ft (3.0 m) Part Number 350008

LOCATION REQUIREMENTS

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer. Do not install in a garage.

Failure to do so can result in death, explosion, or fire.

Select proper location for your washer to improve performance and minimize noise and possible "washer walk." Install your washer in a basement, laundry room, closet, or recessed area.

You will need:

[] A location that allows for proper exhaust installation.

See "Venting Requirements." [] A separate 30-amp circuit. [] If you are using a power supply cord, a grounded electrical

outlet located within 2 ft (610 mm) of either side of the washer/

dryer. See "Electrical Requirements." [] A sturdy floor to support the washer/dryer weight (washer/

dryer, water, and load) of 500 Ibs (226.8 kg). [] A level floor with a maximum slope of 1" (25 mm) under entire

washer/dryer. Clothes may not tumble properly and automatic

sensor cycles may not operate correctly if washer/dryer is not

level. Installing on carpet is not recommended. [] A water heater set to deliver 120°F (49°C) water to the washer. [] Hot and cold water faucets located within 4 ft (1.2 m) of the

hot and cold water fill valves, and water pressure of 5-100 psi

(34.5-689.6 kPa). The washer/dryer must not be installed or stored in an area where

it will be exposed to water and/or weather. Do not operate your washer in temperatures at or below 32°F

(0°C). Some water can remain in the washer and can cause damage in low temperatures. See "Washer/Dryer Care" in the Washer/Dryer Use and Care Guide for winterizing information.

Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times.

Check code requirements. Some codes limit, or do not permit, installation of the washer/dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.

Recessed area or closet installation

48 in.2

(310 cm2)

Front View

Closet

door

(76mr

24 in?

(155 cm2)

The spacing dimensions above are recommended for this washer/dryer. This washer/dryer has been tested for spacing of 0" (0 mm) clearance on the sides. Recommended spacing should be considered for the following reasons:

[] Additional spacing should be considered for ease of

installation and servicing.

[] Additional clearances might be required for wall, door, and

floor moldings.

[] Additional spacing on all sides of the washer/dryer is

recommended to reduce noise transfer.

[] For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

Mobile Home = Additional Installation Requirements This washer/dryer is suitable for mobile home installations.

The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or the Canadian Manufactured Home Standard, CAN/CSA-Z240 MH.

Mobile home installations require: [] Metal exhaust system hardware, which is available for

purchase from your dealer.

[] Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.

DIMENSIONS/CLEARANCES

Dimensions

Front View

Side View

713/4,""

(182'; mm]

1 "

(25 ram)

p 73/4"

2!3 ram) _ 26"

(692 ram)

OooooO

(660 ram) I

Clearances

Side Clearances (recommended/minimum)

/_, _ /h

\/ 0 0 r_ 0 \j

]

1"/0"_ ___ _ 1"/O"

(25 rara/O rara) (25 rara/O ram)

Front/Back/Top Clearances

(305 ram)

12"

88s/4"

(1670 ram)

Back View

41 t/4"

32V8"

(8!6 ram)

(279 ram)

[_32" -_

(8!3 ram)

27V4"-_.

(892 ram)

34"

(884 mm)

1 H

(25 ram)

713/,4""

(1822 ram)

(25 turn) (127 ram)

(Closet)

(1,04 i rara)

DRAIN SYSTEM

Drain system can be installed using a floor drain, wall standpipe,

floor standpipe, or laundry tub. Select method you need.

Floor standpipe drain system Minimum diameter for a standpipe drain: 2" (51 mm). Minimum

carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe must be at least 39" (990 mm) high; install no higher than 96" (2.4 m) from bottom of washer/dryer. If you must install higher than 96" (2.4 m), you will need a sump pump system.

Wall standpipe drain system See requirements for floor standpipe drain system.

Floor drain system Floor drain system requires a Siphon Break Kit (Part Number

285834), 2 Connector Kits (Part Number 285385), and an Extension Drain Hose (Part Number 285863) that may be

purchased separately. To order, please see toll-free phone numbers in your Use and Care Guide. Minimum siphon break:

28" (710 mm) from bottom of washer/dryer. (Additional hoses may be needed.)

Laundry tub drain system Minimum capacity: 20 gal. (76 L). Top of laundry tub must be

at least 39" (990 mm) above floor; install no higher than 96" (2.4 m) from bottom of washer/dryer.

IMPORTANT: To avoid siphoning, no more than 4.5" (114 mm) of drain hose should be inside standpipe or below the top of wash tub. Secure drain hose with shipping strap.

ELECTRICAL REQUIREMENTS - U.S.A.

Electrical Shock Hazard

Plug into a grounded 3 or 4 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

[] It is recommended that a separate circuit breaker serving only this

appliance be provided. [] To minimize possible shock hazard, the cord must be plugged

into a mating, 3- or 4-prong, grounding-type outlet, grounded

in accordance with local codes and ordinances. If a mating

outlet is not available, it is the personal responsibility and

obligation of the customer to have the properly grounded

outlet installed by a qualified electrician. [] If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that

the ground path is adequate. [] Check with a qualified electrician if you are not sure the

washer is properly grounded. [] Do not have a fuse in the neutral or ground circuit.

it is your responsibility: [] To contact a qualified electrical installer. [] To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSVNFPA

70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269. [] To supply the required 3 or 4 wire, single phase, 120/240 volt,

60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt

electrical supply, if specified on the serial/rating plate) on a

separate 30-amp circuit, fused on both sides of the line. A

time-delay fuse or circuit breaker is recommended. Connect

to an individual branch circuit. [] Do not use an extension cord.

Electrical Connection To properly install your washer/dryer, you must determine the

type of electrical connection you will be using and follow the instructions provided for it here.

[] This washer/dryer is manufactured ready to install with a

3-wire electrical supply connection. The neutral ground wire is permanently connected to the neutral conductor (white wire)

within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground wire must be removed

from the internal ground connector (green screw), and secured under the neutral terminal (center or white wire) of the

terminal block. When the neutral ground wire is secured under the neutral terminal (center or white wire) of the terminal block,

the dryer cabinet is isolated from the neutral conductor.

[] If local codes do not permit the connection of a neutral ground

wire to the neutral wire, see "Optional 3-wire connection" in the "Electrical Connection" section.

[] A 4-wire power supply connection must be used when the

appliance is installed in a location where grounding through the neutral conductor is prohibited. Grounding through the

neutral is prohibited for (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas

where local codes prohibit grounding through the neutral conductors.

if using a power supply cord: Use a UL listed power supply cord kit marked for use with

clothes dryers. The kit should contain: [] A UL listed 30-amp power supply cord, rated 120/240 volt

minimum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned

ends.

[] A UL-listed strain relief.

if your outlet

4-wire

receptacle

(14-30R)

if your outlet

3-wire

receptacle

(10-30R)

if connecting by direct wire: Power supply cable must match power supply (4-wire or 3-wire)

and be: [] Flexible armored cable or nonmetallic sheathed copper

cable (with ground wire), covered with flexible metallic

conduit. All current-carrying wires must be insulated. [] 10-gauge solid copper wire (do not use aluminum). [] At least 5 ft (1.52 m) long.

looks like this:

Then choose a 4-wire power supply cord with ring or spade terminals and UL-listed strain relief. The 4-wire power supply cord, at least 4 ft (1.22 m)

long, must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground conductor) may be either green or bare. The neutral conductor must be

identified by a white cover.

looks like this:

Then choose a 3-wire power supply cord with ring or spade terminals and UL-listed strain relief. The 3-wire power supply cord, at least 4 ft (1.22 m) long, must have three 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 10-30R.

ELECTRICAL REQUIREMENTS - U.S.A.

GROUNDING iNSTRUCTiONS

For a grounded, cord-connected washer/dryer:

This washer/dryer must be grounded, in the event of a

malfunction or breakdown, grounding will reduce the risk of electrical shock by providing a path of least resistance for electric current. This washer/dryer is equipped with a cord

having an equipment=grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet

that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman ifyou are

in doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance - if it will

not fit the outlet, have a proper outlet installed by a qualified electrician.

For a permanently connected washer/dryer: This washer/dryer must be connected to a grounded metal, permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead

on the appliance.

SAVE THESE INSTRUCTIONS

ELECTRICAL REQUIREMENTS - CANADA

Electrical Shock Hazard

Plug into a grounded 4 prong outlet, Failure to do so can result in death or electrical shock.

it is your responsibility:

[] To contact a qualified electrical installer. [] To be sure that the electrical connection is adequate and in

conformance with Canadian Electrical Code, C22.1 - latest edition and all local codes. A copy of above codes standard may be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

[] To supply the required 4-wire, single-phase, 120/240 volt,

60 Hz, AC-only electrical supply on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit

breaker is recommended. Connect to an individual branch circuit.

[]

This dryer is equipped with a CSA International Certified Power Cord

intended to be plugged into a standard 14-30R wall receptacle. The cord is 5 ft. (1.52 m) long. Be sure wall receptacle is within reach of dryer's final location. 4-wire receptacle

(14-30R)

If using a replacement power supply cord, it is recommended that you use Power Supply Cord Replacement Part Number 9831317.

For further information, please reference service numbers located in "Assistance or Service" section of your Use and Care Guide.

GROUNDING iNSTRUCTiONS

[] For a grounded, cord-connected washer/dryer: This washer/dryer must be grounded. In the event of

malfunction or breakdown, grounding will reduce the risk of

electric shock by providing a path of least resistance for electric current. This washer/dryer is equipped with a cord

having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with

all local codes and ordinances.

WARNING" Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the washer/dryer is properly grounded. Do not modify the plug provided with the washer/dryer: if it will not fit the outlet,

have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

REMOVE SHIPPING STRAP

INSTALL LEVELING LEGS

Excessive Weight Hazard

Use two or more people to move and install washer/dryer. Failure to do so can result in back or other injury.

To avoid floor damage, set washer/dryer onto cardboard before moving across floor. Move washer/dryer close to its final location.

Remove strap, hang tag, and pin

Do not cut yellow strap. Pull yellow strap firmly, until completely removed from washer/dryer. There should be 2 cotter pins on the end of the shipping strap. Remove the hang tag and pin from the vent pipe.

Excessive Weight Hazard

Use two or more people to move and install washer/dryer. Failure to do so can result in back or other injury.

"1, Prepare to install leveling feet

Prop up the front of the washer/dryer about 4" (102 mm) with a wood block or similar object that will support the weight of the washer/dryer. Then screw the Iocknut onto each foot to within 1" (25 mm) of the foot base.

Check rear leveling legs

Tilt the washer/dryer forward. Move each of the 2 rear legs in an up-down motion to check the self-adjusting leveling legs for free movement. This is required for proper leveling. Gently lower the washer/dryer to the floor.

Cut shipping strap

2, Install front leveling feet

Screw the feet into the threaded holes at the front corners of the washer/dryer until

the jam nuts touch the washer. NOTE: Do not tighten the nuts until the washer/dryer is level.

Tilt the washer/dryer back and remove the wood block. Gently lower the washer/dryer to the floor.

Cut the shipping strap about 16" (406 mm) from the plug end. Look for the words "CUT HERE." Discard end with cotter pins. You will use the remaining piece of shipping strap to secure

the drain hose.

ELECTRICAL CONNECTION (U.S.A. ONLY)

Power Supply Cord

Fire Hazard

Use a new UL listed 30 amp power supply cord. Use a UL listed strain relief.

Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal.

Ground wire (green or bare wire) must be connected to green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold). Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electrical shock.

Direct Wire

Fire Hazard

Use 10 gauge copper wire. Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal.

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electrical shock.

Electrical Connection Options

=1, Choose electrical connection type

Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to "4-wire Power Supply Cord Connection" section. Then, go to "Venting Requirements."

Power supply cord 3-wire receptacle (NEMA Type 10-30R): Go to "3-wire Power Supply Cord Connection" section. Then go to "Venting Requirements."

4-wire direct connection: Go to "4-wire Direct Wire Connection" section. Then go

to "Venting Requirements."

3-wire direct connection: Go to "3-wire

Direct Wire Connection" section. Then go to "Venting Requirements."

NOTE: If local codes do not permit connection of a

cabinet-ground conductor to neutral wire, go to "Optional

3-wire Connection" section. This connection may be

used with either a power supply cord or a direct wire connection.

2, Remove terminal block cover

B C DA

............. I.,_==i.._

r ...... "L"_E

Before you start, disconnect power. Remove hold-down screw (D) and terminal block cover (A).

A. Terminal block cover

B. External ground conductor screw

C. Center terminal block screw

D. Hold-down screw E. Neutral ground wire

R Hole below terminal block cover

Power Supply Cord Connection

Power Supply Cord Strain Relief

"1, Attach power supply cord strain

relief

Remove the screws from a 3/4" (19 mm) UL-listed strain relief (UL marking on strain relief). Put the tabs of the two clamp

sections (C) into the hole below the terminal block opening (B) so that one tab is pointing up (A) and the other is pointing

down (D), and hold in place. Tighten strain relief screws just enough to hold the two clamp sections (C) together.

_, Attach power supply cord

to strain relief

4-Wire Power Supply Cord Connection

iMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire

connections.

4-wire receptacle (NEMA type 14-30R)

Spade terminals with upturned ends

4-prong plug

Ring terminals

Prepare to connect neutral ground wire and neutral wire.

Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this point.

if your outlet looks like this:

Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to "4-Wire Power Supply Cord Connection" on this page.

Power supply cord 3-wire receptacle (NEMA Type 10-30R): Go to "3-Wire Power Supply Cord Connection" on page 13.

Remove center terminal block screw (B). Remove neutral ground wire (E)from external ground conductor screw (A).

Connect neutral ground wire and neutral wire

Connect neutral ground wire (E) and neutral wire (white or

center) (C) of power supply cord under center terminal block screw (B). Tighten screw.

J---__jiS

\ \

Connect ground wire (F)(green or bare) of power supply cord to external ground conductor screw (A).Tighten screw.

Connect remaining wires to outer terminal block screws. Tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to "Venting Requirements."

Remove center terminal block screw (B).

2, Connect neutral wire

Connect neutral wire (white or center) (C) of power supply cord to center terminal block screw (B). Tighten screw.

3. Connect remaining wires

3=Wire Power Supply Cord Connection

iMPORTANT: Use where local codes permit connecting

cabinet-ground conductor to neutral wire.

3-wire receptacle (NEMA type 10-30R)

Spade terminals with upturned ends

3-prong plug

Ring terminals

Connect remaining wires to outer terminal block screws. Tighten screws. Finally, reinsert tab of terminal block cover

into slot of dryer rear panel. Secure cover with hold-down

screw. Now, go to "Venting Requirements."

Direct Wire Connection

Direct Wire Strain Relief

"1, Attach direct wire strain relief

Unscrew the removable conduit connector (A) and any screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief (C) through the hole below the terminal block opening (B). Reaching inside the terminal block opening, screw the removable conduit connector (A) onto the strain relief threads.

2, Attach direct wire cable to strain relief

4-Wire Direct Wire Connection

iMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit 3-wire

connections.

"1, Prepare your 4-wire cable for direct

connection

(127

Direct wire cable must have 5 ft. (1.52 m) of extra length so washer/dryer may be moved if needed.

Strip 5" (127 mm) of outer covering from end of cable,

leaving bare ground wire at 5" (127 mm). Cut 11/2" (38 mm) from remaining 3 wires. Strip insulation back 1" (25 mm). Shape ends of wires into hooks.

Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the

direct wire cable.

if your wiring looks like this:

4-wire direct connection:

Go to "4-Wire Direct Connection" on

this page.

3-wire direct connection:

Go to "3-Wire Direct Connection" page 15.

Remove center terminal block screw (B). Remove neutral ground wire (E) from external ground conductor screw (A).

+ 30 hidden pages