Whirlpool 4GWTW4950YW2 Installation Guide

WASHER INSTALLATION INSTRUCTIONS

INSTRUCTIONS POUR UINSTALLATION DU LAVE-LINGE

INSTRUCCIONES DE INSTALACION DE LA LAVADORA

Table of Contents

WASHER SAFETY ...................................................................... 2

iNSTALLATiON REQUIREMENTS ............................................. 2

Tools and Parts ................................................................... 2

Location Requirements ..................................................... 3

Drain System ...................................................................... 3

Electrical Requirements .................................................... 4

Table des mati_res

SLeCURIT# DU LAVE-LINGE .................................................... 10

EXIGENCES D'INSTALLATION ............................................... 10

Outillage et pi_ces ........................................................... 10

Exigences d'emplacement .............................................. 11

Syst_me de vidange ......................................................... 11

Sp6cifications _lectriques ............................................... 12

iNSTALLATiON iNSTRUCTiONS ............................................... 5

Connect Drain Hose ........................................................... 6

Connect inlet Hoses ........................................................... 6

Level Washer ...................................................................... 8

Power Cord InstaJlation ..................................................... 9

Complete Installation Checklist ........................................ 9

iNSTRUCTiONS D'INSTALLATION ......................................... 13

Raccordement du tuyau de vidange ............................... 14

Raccordement des tuyau× d'arriv_e d'eau .................... 15

Etablissement de I'aplomb du lave=linge ....................... 16

installation du cordon d'alimentation ............................. 17

Liste de v_rification pour I'ach_vement

de I'installation ................................................................. 18

SEGURIDAD DE LA LAVADORA ............................................. 19

REQUISITOS DE INSTALACION ............................................. 19

Herramientas y piezas ..................................................... 19

Requisitos de ubicaci6n .................................................. 20

Sistema de desagiJe ......................................................... 20

Requisitos el6ctricos ....................................................... 21

W10549313A

INSTRUCCIONES DE INSTALACION ..................................... 22

Cone×i6n de la manguera de desagQe ........................... 23

Conexi6n de las mangueras de entrada ........................ 24

Nivelaci6n de la lavadora ................................................ 25

Instalaci6n del cable el_ctrico ........................................ 26

Lista de control de la instalaci6n terminada ................. 27

4GWTW4740

4GWTW4800 4GMVWCl00 4GMVWC300

4GWTW5550

4GWTW4950

4GMVWX500 4GMVWC400

4GNTW4400 4GNTW4600

4GATW4900

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

INSTALLATION REQUIREMENTS

Tools and Parts Gather required tools and parts before starting installation.

Tools needed:

Parts supplied: NOTE: All parts supplied for installation are in cardboard

insert in the top of the washer.

Adjustable or open end wrench 9/16" (14 mm)

4" rain

(102 mm)_

Wood block

Pliers that open to 13A'' (44.5 mm)

Optional tools:

Level Cable tie

Ruler or measuring tape

Net hoses with flat washers

£1 c0

Plugs and cord lock cover

Drain hose with clamp

"Y" connector

Flashlight

Bucket

Alternate parts: (Not supplied with washer) Your installation may require additional parts. To order, please

contact the dealer from whom you purchased your washer or an authorized service company.

If you have: Overhead sewer

You will need:

Standard 20 gal. (76 L) 39" (990 mm) tall drain tub or utility sink, sump pump and connectors (available from local plumbing suppliers)

1" (25 mm) standpipe

2" (51 mm) diameter to 1" (25 mm) diameter Standpipe Adapter

Part Number 3363920 Connector Kit Part Number 285835

Drain hose too short Extension Drain Hose Part

Number 285863 Connector Kit Part Number 285835

Lint clogged drain

Drain Protector Part Number 367031 Connector Kit Part Number 285835

LOCATIONREQUIREMENTS

Select proper location for your washer to improve performance and minimize noise and possible "washer walk". Install your washer in a basement, laundry room, closet, or recessed area.

42"

(1067mm)

Recessed area or closet installation

(76 ram)

14 =.max. i

(356 ram) .... j__.

117"

(432 ram)

48 in.2

(310 cm2)

¢3

,L,,:,i

24 in.2

5H _ n_ll

(126 m , ,,,,

\ \t iq

\%q

Jlq

(155 cm2)

(25 ram)

(76 ram)

Dimensions show recommended spacing allowed, except for closet door ventilation openings which are minimum required. This washer has been tested for installation with spacing of 0" (0 mm) clearance on the sides. Consider allowing more space for ease of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and floor moldings. Add spacing of 1" (25 mm) on all sides of washer to reduce

noise transfer. If a closet door or Iouvered door is installed, top and bottom air openings in door are required.

DRAIN SYSTEM

You will need:

[] A water heater set to 120 ° F (49° C). [] A grounded electrical outlet located within 4 ft (1.2 m) of

power cord on back of washer.

[] Hot and cold water faucets located within 3 ft (0.9 m) of hot

and cold water fill valves on washer, and water pressure of 20-100 psi (138-690 kPa).

[] A level floor with maximum slope of 1" (25 mm) under entire

washer. Installing on carpet is not recommended.

[] Floor must support washer's total weight (with water and load)

of 315 Ibs (143 kgs).

IMPORTANT: Do not install, store, or operate washer where it will be exposed to weather or in temperatures below 32° F (0° C). Water remaining in washer after use may cause damage in low temperatures. See "Washer Care" in your Use and Care Guide for winterizing information.

Proper installation is your responsibility.

Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need.

Floor standpipe drain system

Minimum diameter for a standpipe drain: 2" (51 mm). Minimum carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe must be at least 39" (990 mm) high; install no higher than 48" (1.22 m) from bottom of washer. If you must install higher than 48" (1.22 m), you will need a sump pump system.

Wall standpipe drain system

See requirements for floor standpipe drain system. Floor drain system

(

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Floor drain system requires a Siphon Break Kit (Part Number

285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be purchased separately. To order, please contact the dealer from whom you purchased your washer or an authorized service company. Minimum siphon break: 28" (710 mm) from bottom of washer. (Additional hoses may be needed.)

Laundry tub drain system

Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at least 39" (990 mm) above floor; install no higher than 48" (1.22 m)

from bottom of washer.

iMPORTANT: To avoid siphoning, no more than 4.5" (114 mm) of drain hose should be inside standpipe or below the top of

wash tub. Secure drain hose with cable tie.

[] A 220-240 volt, 60 Hz., AC only, 10-amp, fused electrical supply

is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit breaker serving only this

appliance be provided.

[] This washer is equipped with a power supply cord having

a 3 prong grounding plug.

[] To minimize possible shock hazard, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet

is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed

by a qualified electrician.

[] If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the ground path is adequate.

[] Do not ground to a gas pipe. [] Check with a qualified electrician ifyou are not sure the

washer is properly grounded.

[] Do not have a fuse in the neutral or ground circuit.

GROUNDING INSTRUCTIONS

For a grounded, cord=connected washer:

This washer must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical

shock by providing a path of least resistance for electric current. This washer is equipped with a cord having an equipment=grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local codes and ordinances.

WARNING: improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman ifyou are

in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance - if it will

not fit the outlet, have a proper outlet installed by a qualified

electrician.

For a permanently connected washer: This washer must be connected to a grounded metal, permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead

on the appliance.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard Use two or more people to move and install washer. Failure to do so can result in back or other injury.

Before you start: remove shipping materials It is necessary to remove all shipping materials for proper

operation and to avoid excessive noise from washer.

1. Move washer

Remove packing tray from tub

Remove tape from washer lid, open lid and remove cardboard packing tray from tub. Be sure to remove all parts from tray.

NOTE: Keep tray in case you need to move washer later.

f4. Free power cord

Move washer to within 4 ft (1.2 m) of its final location; it must be in a fully upright position.

NOTE: To avoid floor damage, set washer onto cardboard before moving it and make sure lid is taped shut.

2. Remove shipping base

To avoid damaging floor, place cardboard supports from shipping carton on floor behind washer. Tip washer back and place on cardboard supports. Remove shipping base. Set washer upright.

IMPORTANT: Removing shipping base is necessary for proper operation. If your washer includes a sound shield, please refer

to the instructions included with the sound shield to install it at this time.

Firmly grasp power cord plug and pull to free from rear panel. Gently place power cord over console to allow free access

to back of washer.

CONNECT DRAIN HOSE

Attach drain hose to drain port

Remove drain hose form (floor drain installations only}

Remove the red plastic plug from the black drain port on the back of the washer.

If clamp is not already in place on elbow end of drain hose, slide it over end as shown. Squeeze clamp with pliers and slide black elbow end of drain hose onto black drain port and secure with clamp.

For a laundry tub or standpipe drain, go to step 6. For a floor drain, remove the preinstalled drain hose form as

shown in Step 7. You may need additional parts with separate directions. See "Tools and Parts".

F6, Place drain hose in standpipe

Drain

For floor drain installations, you will need to remove the drain hose form from the end of the drain hose. You may need additional parts with separate directions. See "Tools and Parts".

CONNECT INLET HOSES

Washer must be connected to water faucets with new inlet hoses with flat washers (provided). Do not use old hoses.

NOTE: Both hoses must be attached and have water flowing to inlet valves. If you are only connecting to a cold water faucet, you must use a Y-adapter (provided).

Connect inlet hoses to water

Place hose into standpipe (shown in picture) or over side of laundry tub.

IMPORTANT: 4.5" (114 mm) of drain hose should be inside standpipe; do not force excess hose into standpipe or lay on

bottom of laundry tub. Drain hose form must be used.

Attach hose to hot water faucet. Screw on coupling by hand until it is seated on washer. Use pliers to tighten couplings an

additional two-thirds turn. Repeat this step with second hose for cold water faucet.

IMPORTANT: Do not overtighten or use tape or sealants on valve when attaching to faucets or washer. Damage can result.

Attach the brass female end of the "Y" connector to the cold water faucet. Use pliers

to tighten couplings an additional two-thirds turn. One end of the long hose has a wire mesh strainer inside the coupling.

Attach this end to the "Y" connector. Attach washer cold inlet hose to other side of "Y" connector. Screw on coupling by

hand until it is seated on connector. Using pliers, tighten the couplings an additional two-thirds turn.

IMPORTANT: Do not overtighten or use tape or sealants on valve when attaching to faucets or washer. Damage

can result.

9. Clear water lines

flO. Connect inlet hoses to washer

#0@_' ¢@Li#

Attach hot water hose to hot water inlet valve marked with a red ring. Screw coupling by hand until it is snug. Use pliers to

tighten couplings an additional two-thirds turn. Repeat with cold water inlet valve.

IMPORTANT: To reduce risk of hose failure, replace the hoses every 5 years. Record hose installation or replacement dates

for future reference. [] Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

11. Check for leaks

Run water for a few seconds through hoses into a laundry tub, drainpipe, or bucket to avoid clogs. Water should run until clear.

Make note of which hose is connected to hot water to help in attaching hoses to washer correctly.

Turn on water faucets to check for leaks. A small amount of water may enter washer. It will drain later.

Standpipe

Secure drain hose to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with cable tie.

LEVEL WASHER

IMPORTANT: Level washer properly to reduce excess noise and vibration.

3. Check levelness of washer

4. Adjust leveling feet

Place level here Place level here

Move the washer to its final location. Place a level on top edges of washer. Use side seam as a guide to check levelness of sides. Check levelness of front using lid, as shown. Rock

washer back and forth to make sure all four feet make solid contact with floor. If washer is level, skip to step 15, (on

models with metal feet) or step 16 (on models with plastic feet).

Not Level LEVEL Not Level

Models with

metal feet

Jam nut

Models with

plastic feet

if washer is not level:

On models with metal feet, use a 9/16" or 14 mm open-end or adjustable wrench to turn jam nuts clockwise on feet until they are about 1/2" (13 mm) from the washer cabinet. Then turn the leveling foot clockwise to lower the washer or counterclockwise

to raise the washer. On models with plastic feet, use adjustable pliers to turn the

plastic leveling foot counterclockwise to lower the washer or clockwise to raise the washer. On all models, recheck levelness

of washer and repeat as needed. HELPFUL TIP: You may want to prop up front of washer

about 4" (102 mm) with a wood block or similar object that will support weight of washer.

15. Tighten leveling feet

Jam nut

On models with metal feet, when washer is level, use a 9/16" or 14 mm open-end or adjustable wrench to turn jam nuts counterclockwise on leveling feet tightly against washer

cabinet. HELPFUL TIP: You may want to prop washer with

wooden block.

POWER CORD INSTALLATION

"a,

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Plug power supply cord into an grounded outlet. Turn power supply on.

Select plug

Select the plug that fits with the electric receptacle.

18, Secure power cord

Secure the power cord by seating the connection on the cord lock. Place the cord lock cover and push until it snaps. Make sure the power cord connection is seated on the cord lock and that the cord lock clamps correctly.

COMPLETE INSTALLATION CHECKLIST

[_ Check electrical requirements. Be sure you have correct

electrical supply and recommended grounding method.

[_ Check that all parts are now installed. If there is an extra

part, go back through steps to see what was skipped.

[_ Check that you have all of your tools. [_ Check that shipping materials were completely

removed from washer. Check that water faucets are on.

Check for leaks around faucets and inlet hoses.

C3 C3

Remove film from console and any tape remaining on washer.

Check that washer is plugged into a grounded outlet.

Dispose of/recycle all packaging materials.

Read "Washer Care" in your Use and Care Guide.

Totest and clean your washer, measure 1/2 of normal recommended amount of powdered or liquid detergent and pour it into washer basket or detergent dispenser (on some models). Close lid. Select any cycle. Start washer and allow to complete full cycle.

Assemble the plug into the end of the power cord.

+ 18 hidden pages