Whirlpool 1CWTW4840YW1, 2DWTW4740YQ1, 1CWTW4800YQ1, 1CWTW4740YQ1, 2DWTW4800YQ1 Installation Guide

WASHER INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACION DE LA LAVADORA

Table of Contents

WASHER SAFETY .............................................................. 1

iNSTALLATiON REQUIREMENTS ..................................... 2

Tools and Parts ..................................................................... 2

Location Requirements ....................................................... 2

Drain System ........................................................................ 3

Electrical Requirements ...................................................... 4

iNSTALLATiON iNSTRUCTiONS ....................................... 4

Before you start: remove shipping materials .................... 4

Connect Drain Hose ............................................................. 5

Connect Inlet Hoses ............................................................. 6

Level Washer ........................................................................ 7

Complete Installation Checklist .......................................... 8

iNSTALLATiON NOTES

Date of purchase: Date of installation:

Installer: Model number:

Serial number:

P •

In&ce

SEGURIDAD DE LA LAVADORA ................................. 9

REQUISITOS DE INSTALACION ................................. 9

Herramientas y piezas ................................................... 9

Requisitos de ubicaciSn ............................................... 10

Sistema de desag_e ...................................................... 11

Requisitos el_ctricos .................................................... 11

INSTRUCCIONES DE INSTALACION ........................ 12

Antes de comenzar: quite los materiales

de transporte ................................................................. 12

Cone×iSn de la manguera de desag_e ........................ 13

Cone×iSn de las mangueras de entrada ..................... 14

NivelaciSn de la lavadora ............................................. 15

Complete la instalaciSn ........................... Contraportado

NOTAS SOBRE LA INSTALACION

Fecha de compra: Fecha de instalaciSn:

Instalador:

N_mero de modelo: N_mero de serie:

WASHER S_ETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

W10449043A

INSTALLATION REQU[REMENW$

Tools and Parts Gather required tools and parts before starting installation.

Tools needed:

Adjustable or open end wrench 9/16"(14 mm)

4 =.n3in

(102 mm}_

Level

Wood block

Ruler or measuring tape

Alternate parts: (Not supplied with washer) Your installation may require additional parts. To order, please

contact the dealer from whom you purchased your washer or an authorized service company.

If you have: Overhead sewer

1" (25 mm) standpipe

Drain hose too short Extension Drain Hose Part

Lint clogged drain

You will need:

Standard 20 gal. (76 L) 39" (990 mm) tall drain tub or utility sink, sump pump and connectors (available from local plumbing suppliers)

2" (51 mm) diameter to 1" (25 mm) diameter Standpipe Adapter

Part Number 3363920 Connector Kit Part Number 285835

Number 285863 Connector Kit Part Number 285835

Drain Protector Part Number 367031 Connector Kit Part Number 285835

LOCATION REQU[REMENWS

Select proper location for your washer to improve performance and minimize noise and possible "washer walk". Install your washer in a basement, laundry room, closet, or recessed area.

Pliers that open to 1%6" (39.5 mm)

Optional tools:

Flashlight Bucket Parts supplied:

NOTE: All parts supplied for installation are in cardboard insert in the top of the washer.

Drain hose with clamp, U-form, and cable tie

"Y" connector

]

42"

(1067mm)

You will need:

[] A water heater set to 120 ° F (49° C). [] A grounded electrical outlet located within 4 ft (1.2 m) of

power cord on back of washer.

[] Hot and cold water faucets located within 3 ft (0.9 m) of hot

and cold water fill valves on washer, and water pressure of 5-116 psi (35-800 kPa).

[] A level floor with maximum slope of 1" (25 mm) under entire

washer. Installing on carpet is not recommended.

[] Floor must support washer's total weight (with water and load)

of 315 Ibs (143 kgs).

IMPORTANT: Do not install, store, or operate washer where it will be exposed to weather or in temperatures below 32° F (0° C). Water remaining in washer after use may cause damage in low temperatures. See "Washer Care" in your Use and Care Guide for winterizing information.

Proper installation is your responsibility.

Net hoses Rubber washer

Recessed area or closet installation

Wall standpipe drain system

3 II

(76 ram)

14" max. i

1356 ram) .... j_ _

,, I'4

E _ _q

* tq

511 i tll

(126 m , ,,,,

• \t ih \%q

f 17"'

(432 ram)

i,ii

iiii

48 in.2

(310 cm2)

24 in.2

(155cm_1

t/22111

%1"

(25 ram)

Dimensions show recommended spacing allowed, except for closet door ventilation openings which are minimum required. This washer has been tested for installation with spacing of 0" (0 mm) clearance on the sides. Consider allowing more space for ease of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and floor moldings. Add spacing of 1" (25 mm) on all sides of washer to reduce

noise transfer. If a closet door or Iouvered door is installed, top and bottom air openings in door are required.

D IN SYSTEM

(76 ram)

See requirements for floor standpipe drain system. Floor drain system

Floor drain system requires a Siphon Break Kit (Part Number

285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be purchased separately. Toorder, please contact the dealer from whom you purchased your washer or an authorized service company. Minimum siphon break: 28" (710 mm) from bottom of washer. (Additional hoses may be needed.)

Laundry tub drain system

Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need.

Floor standpipe drain system

Minimum diameter for a standpipe drain: 2" (51 mm). Minimum carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe must be at least 39" (990 mm) high. For models with 1C prefix, install no higher than 96" (2.44 m) from bottom of washer. For models with 2D prefix, install no higher than 48" (1.22 m). if you must install higher than the recommended height for your model, you will need a sump pump system.

Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at

least 39" (990 mm) above floor. For models with 1C prefix, install no higher than 96" (2.44 m) from bottom of washer. For models with 2D prefix, install no higher than 48" (1.22 m).

IMPORTANT: To avoid siphoning, no more than 4.5" (114 mm) of drain hose should be inside standpipe or below the top of

wash tub. Secure drain hose with cable tie.

ELEC%RIC, REQU[REMENT$

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install washer. Failure to do so can result in back or other injury.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

[] Models beginning with 1C use 120 volt, 60 Hz and models

beginning with 2D, use 120 volt, 50 Hz., both are AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse

or circuit breaker is recommended. It is recommended that a separate circuit breaker serving only this appliance be provided.

[] This washer is equipped with a power supply cord having

a 3 prong grounding plug.

[] To minimize possible shock hazard, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet

is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed

by a qualified electrician.

[] If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that

the ground path is adequate. [] Do not ground to a gas pipe. [] Check with a qualified electrician if you are not sure the

washer is properly grounded. [] Do not have a fuse in the neutral or ground circuit.

Before you start: remove shipping materials It is necessary to remove all shipping materials for proper

operation and to avoid excessive noise from washer.

1. Move washer

Move washer to within 4 ft (1.2 m) of its final location; it must be in a fully upright position.

NOTE: To avoid floor damage, set washer onto cardboard before moving it and make sure lid is taped shut.

f2. Remove shipping base

GROUNDING INSTRUCTIONS

For a grounded, cord-connected washer:

This washer must be grounded, in the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by providing a path of least resistance for electric current. This washer is equipped with a cord having an

equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local

codes and ordinances.

WARNING: Improper connection of the equipment=

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in

doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance - if it will

not fit the outlet, have a proper outlet installed by a qualified

electrician.

For a permanenUy connected washer: This washer must be connected to a grounded metal, permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and connected to the equipment=grounding terminal or lead on

the appliance.

To avoid damaging floor, place cardboard supports from shipping carton on floor behind washer. Tip washer back and place on cardboard supports. Remove shipping base. Set washer upright.

IMPORTANT: Removing shipping base is necessary for proper operation. If your washer includes a sound shield, please refer

to the instructions included with the sound shield to install it at this time.

Remove packing tray from tub

Remove tape from washer lid, open lid and remove cardboard packing tray from tub. Be sure to remove all parts from tray.

NOTE: Keep tray in case you need to move washer later.

(f4. Free power cord

_"6. Place drain hose in standpipe

Drain

Place hose into standpipe (shown in picture) or over side of laundry tub.

iMPORTANT: 4.5" (114 mm) of drain hose should be inside standpipe; do not force excess hose into standpipe or lay on bottom of laundry tub. Drain hose form must be used.

7. Remove drain hose form

(floor drain installations only)

Firmly grasp power cord plug and pull to free from rear panel. Gently place power cord over console to allow free access

to back of washer.

CON_CT DRAIN HOSE

Attach drain hose to drain port

Remove the red plastic plug from the black drain port on the back of the washer.

If clamp is not already in place on elbow end of drain hose, slide it over end as shown. Squeeze clamp with pliers and

slide black elbow end of drain hose onto black drain port and secure with clamp.

For a laundry tub or standpipe drain, go to step 6. For a floor drain, remove the preinstalled drain hose form as

shown in Step 7. You may need additional parts with separate directions. See "Tools and Parts".

For floor drain installations, you will need to remove the drain hose form from the end of the drain hose. You may need additional parts with separate directions. See "Tools and Parts".

+ 11 hidden pages