wheelock SPRM INSTALLATION INSTRUCTIONS

273 Branchport Avenue
Long Branch, NJ 07740
[phone] Thank you for using our products.
www.cooperwheelock.com

INSTALLATION INSTRUCTIONS

SPRM REMOTE MICROPHONE FOR USE WITH SP40S

Use this product according to this instruction manual. Please keep this instruction manual for future reference.

MODEL NUMBER:

SPRM 108996
SPRM-B 109932

GENERAL:

The Remote Microphone is UL Listed under Standard 864, Control Units for Fire-Protective Signaling Systems. They are Listed for
indoor use only. The Remote Microphone is designed to be used with Wheelock’s SP40S SAFEPATH4 Panel. It provides a means

for making emergency voice announcements from an auxiliary location. Only 1 Remote Microphone can be connected to the SP40S
Panel. The hand held push-to-talk microphone is supervised to ensure proper connection. It is not repairable. If it is detached from
the unit, the unit must be returned for repair.

NOTE: All CAUTIONS and WARNINGS are identified by the symbol . All warnings are printed in bold capital letters.

WARNING: PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT. FAILURE TO COMPLY
WITH ANY OF THE FOLLOWING INSTRUCTIONS, CAUTIONS AND WARNINGS COULD RESULT IN IMPROPER
APPLICATION, INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN AN EMERGENCY SITUATION, WHICH
COULD RESULT IN PROPERTY DAMAGE AND SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS.

SPECIFICATIONS:

Power Input Voltage: 24VDC
Audio Output Level: 1.05V RMS
Output Impedance: 600 Ohms
Min. Ground Fault: 20k Ohms
Input Current: Standby: 23mA
Alarm: 30mA

WIRING DIAGRAM:

Figure 1 shows the proper wiring connections for connecting the SPRM to the SP40S.

SP40S PANEL

TB6

+

AUX IN

-

+

CC/NAC

­+

24V OUT

-

*

*

REMOTE MICROPHONE

+

24VDC

-

RM AUDIO

+

-

54321

+

6

-

STATUS (CC)

Figure 1:

* This wiring is power limited.

NOTE: All wiring is supervised unless otherwise noted.

WIRING SPECIFICATIONS:

Cable Size: 14-18 American Wire Gauge (AWG) Shielded. The shield must be connected only at the SP40S Panel.
Maximum Length: 2000 Feet
Maximum Capacitance: 0.1uF/Total Run (50pF/foot for 1000 FT.)

Copyright 2006 Cooper Wheelock, Inc. All rights reserved.

P84207 Rev. E

Sheet 1 of 4

MOUNTING INSTRUCTIONS:

(A)

SAFEPATH4 REMOTE MICROPHONE STATION

SYSTEM STATUS

NORMAL

ALARM

TROUBLE

4 GANG BACKBOX

OFF

ON

MOUNTING SCREW (A)

MOUNTING
SCREWS

OPERATING INSTRUCTIO N S :

1. Turn key to ON position

2. Press microphone button
and speak into microphone

USER KEY

Figure 2:

Figure 2 shows the proper mounting requirements for the SPRM.

1. Install a 4” gang backbox (either flush or surface) to the desired location. Be sure that the mounting box is level.

2. Attach the 6 wires as shown in the wiring diagram (Figure 1). Be sure to use the specified wire.

3. Attach the mounting plate to the box with the 4 screws as shown in Figure 2.

OPERATING INSTRUCTIONS:

JP4

AUX IN L E D

JP4

R92

R93

R94

R100

SW6 NAC/CC
J4

Figure 3:

Figure 3 shows the locations of the switches and LED’s on the SP40S that require operation during operation and troubleshooting.

1. Set switch SW6 (NAC/CC) to the CC position.

2. Set the jumper on J4 to the 1V position.

3. Remove the jumper on JP4.

4. Insert key and turned to the ON position for the controls to function. (The key is removable only in the OFF position.)

WARNING: IF JP4 JUMPER IS NOT REMOVED THE SP40S WILL NOT BE ABLE TO DETECT ANY REMOTE

MIC TROUBLE.

P84207 Rev. E

Sheet 2 of 4

SAFEPATH4 REMOTE MICROPHONE STATION

SYSTEM STATUS

NORMAL

OPERATING INSTRUCTIONS:

1. Turn key to ON position

2. Press microphone button
and speak into microphone

TROUBLE

ALARM

ON

Figure 4:

Figure 4 shows the SPRM front panel and the location of the LED’s.

NOTE: The green and yellow LED's reflect the system’s condition regardless of the key position. The green LED indicates there
are no faults in the SPRM. The yellow LED indicates a trouble condition has occurred in the SPRM. The red LED indicates the
SPRM is ready to transmit the live voice of the operator.

1. With the mouth one to two inches from the microphone, press the microphone push-to-talk button and speak into the microphone
and deliver the live audible announcement.

TROUBLE SHOOTING:

The yellow “TROUBLE” LED illuminates when there is a problem with the wiring between the SP40S.

The wiring problems that can occur can be improper wiring (reversed) on the Audio connections and/or CC connections. This will
also provide a trouble condition on the SP40S panel with the system TROUBLE LED illuminated and the “AUX IN” (Auxiliary
Input) LED ON. (The SP40S internal sounder will also sound.) If checking and/or correcting problems do not correct the trouble,
then the SPRM should be replaced.

ANY MATERIAL EXTRAPOLATED FROM THIS DOCUMENT OR FROM COOPER WHEELOCK MANUALS OR
OTHER DOCUMENTS DESCRIBING THE PRODUCT FOR USE IN PROMOTIONAL OR ADVERTISING CLAIMS, OR
FOR ANY OTHER USE, INCLUDING DESCRIPTION OF THE PRODUCT'S APPLICATION, OPERATION,
INSTALLATION AND TESTING IS USED AT THE SOLE RISK OF THE USER AND COOPER WHEELOCK WILL
NOT HAVE ANY LIABILITY FOR SUCH USE.

P84207 Rev. E

Sheet 3 of 4

Limited Warranty

Cooper Wheelock, Inc. products must be used within their published specifications and must be PROPERLY specified, applied,
installed, operated, maintained, and operationally tested in accordance with these instructions at the time of installation and at least
twice a year or more often in accordance with local, state and federal codes, regulations and laws. Specification, application,
installation, operation, maintenance, and testing must be performed by qualified personnel for proper operation in accordance with all
of the latest National Fire Protection Association (NFPA), Underwriters' Laboratories (UL), Underwriters’ Laboratories of Canada
(ULC), National Electrical Code (NEC), Occupational Safety and Health Administration (OSHA), local, state, county, province,
district, federal and other applicable building and fire standards, guidelines, regulations, laws and codes including, but not limited to,
all appendices and amendments and the requirements of the local authority having jurisdiction (AHJ). Cooper Wheelock, Inc.
products when properly specified, applied, installed, operated, maintained, and operationally tested as provided above are warranted
against mechanical and electrical defects for a period of three years from date of manufacture (as determined by date code).
Correction of defects by Cooper Wheelock, Inc providing repairs or a replacement shall be at Cooper Wheelock, Inc.'s sole discretion
and shall constitute fulfillment of all warranty obligations. The foregoing limited warranty shall immediately terminate in the event
any part not furnished by Cooper Wheelock, Inc. is installed in the product. The foregoing limited warranty specifically excludes any
software required for the operation of or included in a product. COOPER WHEELOCK, INC. MAKES NO REPRESENTATION

OR WARRANTY OF ANY OTHER KIND, EXPRESS, IMPLIED OR STATUTORY WHETHER AS TO
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER MATTER.

Users are solely responsible for determining whether a product is suitable for the user's purposes, or whether it will achieve the user's
intended results. There is no warranty against damage resulting from misapplication, improper specification, abuse, accident, or other
operating conditions beyond Cooper Wheelock, Inc.'s control.

Some Cooper Wheelock, Inc. products contain software. With respect to those products, Cooper Wheelock, Inc. does not warranty
that the operation of the software will be uninterrupted or error-free or that the software will meet any other standard of performance,
or that the functions or performance of the software will meet the user's requirements. Cooper Wheelock, Inc. shall not be liable for
any delays, breakdowns, interruptions, loss, destruction, alteration, or other problems in the use of a product arising out of or caused
by the software.

The liability of Cooper Wheelock, Inc. arising out of the supplying of a product, or its use, whether based on warranty, negligence, or
otherwise, shall not in any case exceed the cost of correcting defects as stated in the limited warranty and upon expiration of the
warranty period all such liability shall terminate. Cooper Wheelock, Inc. is not liable for labor costs incurred in removal,
reinstallation, or for damage of any type whatsoever, including but not limited to, loss of profit or incidental or consequential
damages. The foregoing shall constitute the sole remedy of the purchaser and the exclusive liability of Cooper Wheelock, Inc.

In no case will Cooper Wheelock, Inc.'s liability exceed the purchase price paid for a product.

Limitation of Liability

Cooper Wheelock, Inc.'s liability on any claim of any kind, including negligence, breach of warranty, or otherwise, for any loss or
damage resulting from, arising out of, or connected with any contract, or from the manufacture, sale, delivery, resale, repair or use of
any product shall be limited to the price applicable to the product or part thereof which gives rise to the claim. Cooper Wheelock,
Inc.'s liability on any claim of any kind shall cease immediately upon the installation in the product of any part not furnishe

d by

Cooper Wheelock, Inc. In no event shall Cooper Wheelock, Inc. be liable for any claim of any kind unless it is proven that our
product was a direct cause of such claim. FURTHER, IN NO EVENT, INCLUDING IN THE CASE OF A CLAIM OF

NEGLIGENCE, SHALL COOPER WHEELOCK, INC. BE LIABLE FOR INCIDENTAL, INDIRECT, SPECIAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages, so

the preceding limitation may not apply to all purchasers.

8/06

P84207 Rev. E

Sheet 4 of 4