Page 1
273 Branchport Avenue
Long Branch, NJ 07740
(800) 631-2148 Thank you for using our products.
www.wheelockinc.com
Use this product according to this instruction manual. Please keep this instruction manual for future reference.
GENERAL:
Wheelock's SAFEPATH
Telephone (TEL) input.
The unit is attractively packaged for wall mounting. The SP-COA requires connection to a 24VDC filtered and regulated power
supply, which supplies power to the unit and talk battery for the unused C.O. Port. Two wires are connected from the unused C.O.
Port to the telephone input (TEL INPUT) terminals on the SP-COA. The telephone output (TEL OUTPUT) is then connected to the
telephone input (TEL) connections on the SP40/2 motherboard. See Figure 2.
NOTE: All CAUTIONS and WARNINGS are identified by the symbol . All warnings are printed in bold capital letters.
WARNING: PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT. FAILURE
TO COMPLY WITH ANY OF THE FOLLOWING INSTRUCTIONS, CAUTIONS AND WARNINGS COULD RESULT IN
IMPROPER APPLICATION, INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN AN EMERGENCY
SITUATION, WHICH COULD RESULT IN PROPERTY DAMAGE AND SERIOUS INJURY OR DEATH TO YOU
AND/OR OTHERS.
INSTALLATION INFORMATION:
WARNING: DO NOT CONNECT AC POWER OR BATTERY BACKUP POWER UNTIL SYSTEM WIRING HAS
BEEN CONNECTED OR THE SP-COA HAS BEEN MOUNTED, AND FIELD WIRING HAS BEEN INSPECTED.
Connect the SP-COA TEL INPUT to the unused C.O. Port or a stand-alone telephone. Connect the SP-COA TEL OUTPUT to the
TEL terminals on TB5 on the SP40/2. Connect the SP-COA POWER terminals to a 24VDC filtered and regulated power supply
(Wheelock’s part number RPS-2406 is recommended). See Figure 1 for details.
INSTALLATION INSTRUCTIONS
SAFEPATH
®
4 C.O. Port Adapter (SP-COA) is used when connecting between an unused C.O. Port and the SP40/2
®
4 C.O. Port Adapter
SP-COA
Figure 1:
-
UNUSED CO
PORT OR
STAND ALONE
TELEPHONE
+
-
Copyright 2002 Wheelock, Inc. All rights reserved.
+
RPS-2406
+
24V INPUT
-
+
TEL
-
INPUT
SP-COA
TEL
OUTPUT
+
-
SP40/2
TEL
+
INPUT
-
P84341 A
Sheet 1 of 4
Page 2
MOUNTING INFORMATION:
Hang the C.O. Port Adapter vertically on the two mounting screws supplied. Space the screws vertically on 2" centers per Figure 3.
Connect all wiring as per Figure 1. The SP-COA terminals accept #16 through #24 AWG. Strip insulation to expose 3/8" of bare
wire. Press in the orange tab above the appropriate terminals with a small screwdriver and insert the bare wire into the wire hole.
Release the tab to securely clamp the wire.
Plug in AC power cord for the 24VDC power supply. Check page activation by operating the page system.
SPECIFICATIONS:
Table 1:
Input Specifications Output Specifications
Input Voltage 24VDC
Input Current Standby .002 Amps
Telephone Output Level
500mVrms
Input Current Page .049 Amps
Telephone Input Level 500mVrms
Figure 2: Wire Connections
+
24VDC
-
TEL INPUT
+
-
+
TEL OUTPUT
-
Figure 3: Mounting Template
(Not To Scale)
P84341 A
Sheet 2 of 4
Page 3
TROUBLE SHOOTING GUIDE:
Condition Check
1) SP-COA cannot be accessed Check presence and polarity of voltage on + & - 24 VDC terminals
and that power is filtered and regulated.
Verify SP-COA has released from last page.
Check the SP40/2 is not in a trouble condition.
Verify that “Tel Input” and “Tel Output” wires are not switched.
2) No sound or low page volume Check for presence of audio on the “Tel Input” terminals.
Increase the “Tel” volume control on the SP40/2 (see SP40/2 manual
for information and location of the “Tel” volume control).
Check the SP40/2 is not in a trouble condition.
P84341 A
Sheet 3 of 4
Page 4
ANY MATERIAL EXTRAPOLATED FROM THIS DOCUMENT OR FROM WHEELOCK MANUALS OR OTHER
DOCUMENTS DESCRIBING THE PRODUCT FOR USE IN PROMOTIONAL OR ADVERTISING CLAIMS, OR FOR
ANY OTHER USE, INCLUDING DESCRIPTION OF THE PRODUCT'S APPLICATION, OPERATION, INSTALLATION
AND TESTING IS USED AT THE SOLE RISK OF THE USER AND WHEELOCK WILL NOT HAVE ANY LIABILITY
FOR SUCH USE.
Limited Warranty
Wheelock products must be used within their published specifications and must be PROPERLY specified, applied, installed, operated,
maintained and operationally tested in accordance with these instructions at the time of installation and at least twice a year or more
often and in accordance with local, state and federal codes, regulations and laws. Specification, application, installation, operation,
maintenance and testing must be performed by qualified personnel for proper operation in accordance with all of the latest National
Electrical Code (NEC), Occupational Safety and Health Administration (OSHA), local, state, county, province, district, federal and
other applicable building standards, guidelines, regulations, laws and codes. Wheelock products when properly specified, applied,
installed, operated, maintained and operationally tested as provided above are warranted against mechanical and electrical defects for
a period of three years from date of manufacture (as determined by date code). Correction of defects by repair or replacement shall be
at Wheelock's sole discretion and shall constitute fulfillment of all obligations under this warranty. THE FOREGOING LIMITED
WARRANTY SHALL IMMEDIATELY TERMINATE IN THE EVENT ANY PART NOT FURNISHED BY WHEELOCK IS
INSTALLED IN THE PRODUCT. THE FOREGOING LIMITED WARRANTY SPECIFICALLY EXCLUDES ANY SOFTWARE
REQUIRED FOR THE OPERATION OF OR INCLUDED IN A PRODUCT. WHEELOCK MAKES NO REPRESENTATION OR
WARRANTY OF ANY OTHER KIND, EXPRESS, IMPLIED OR STATUTORY WHETHER AS TO MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER MATTER.
USERS ARE SOLELY RESPONSIBLE FOR DETERMINING WHETHER A PRODUCT IS SUITABLE FOR THE USER'S
PURPOSES, OR WHETHER IT WILL ACHIEVE THE USER'S INTENDED RESULTS. THERE IS NO WARRANTY AGAINST
DAMAGE RESULTING FROM MISAPPLICATION, IMPROPER SPECIFICATION, ABUSE, ACCIDENT OR OTHER
OPERATING CONDITIONS BEYOND WHEELOCK'S CONTROL.
SOME WHEELOCK PRODUCTS CONTAIN SOFTWARE. WITH RESPECT TO THOSE PRODUCTS, WHEELOCK DOES
NOT WARRANTY THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE OR THAT
THE SOFTWARE WILL MEET ANY OTHER STANDARD OF PERFORMANCE, OR THAT THE FUNCTIONS OR
PERFORMANCE OF THE SOFTWARE WILL MEET THE USER'S REQUIREMENTS. WHEELOCK SHALL NOT BE LIABLE
FOR ANY DELAYS, BREAKDOWNS, INTERRUPTIONS, LOSS, DESTRUCTION, ALTERATION, OR OTHER PROBLEMS IN
THE USE OF A PRODUCT ARISING OUT OF OR CAUSED BY THE SOFTWARE.
THE LIABILITY OF WHEELOCK ARISING OUT OF THE SUPPLYING OF A PRODUCT, OR ITS USE, WHETHER ON
WARRANTIES, NEGLIGENCE, OR OTHERWISE, SHALL NOT IN ANY CASE EXCEED THE COST OF CORRECTING
DEFECTS AS STATED IN THE LIMITED WARRANTY AND UPON EXPIRATION OF THE WARRANTY PERIOD ALL
SUCH LIABILITY SHALL TERMINATE. WHEELOCK IS NOT LIABLE FOR LABOR COSTS INCURRED IN REMOVAL,
REINSTALLATION OR REPAIR OF THE PRODUCT BY ANYONE OTHER THAN WHEELOCK OR FOR DAMAGE OF ANY
TYPE WHATSOEVER, INCLUDING BUT NOT LIMITED TO LOSS OF PROFIT OR INCIDENTAL OR CONSEQUENTIAL
DAMAGES. THE FOREGOING SHALL CONSTITUTE THE SOLE REMEDY OF THE PURCHASER AND THE EXCLUSIVE
LIABILITY OF WHEELOCK.
IN NO CASE WILL WHEELOCK'S LIABILITY EXCEED THE PURCHASE PRICE PAID FOR A PRODUCT.
Limitation of Liability
WHEELOCK'S LIABILITY ON ANY CLAIM OF ANY KIND, INCLUDING NEGLIGENCE AND BREACH OF WARRANTY,
FOR ANY LOSS OR DAMAGE RESULTING FROM, ARISING OUT OF, OR CONNECTED WITH THIS CONTRACT, OR
FROM THE MANUFACTURE, SALE, DELIVERY, RESALE, REPAIR OR USE OF ANY PRODUCT COVERED BY THIS
ORDER SHALL BE LIMITED TO THE PRICE APPLICABLE TO THE PRODUCT OR PART THEREOF WHICH GIVES RISE
TO THE CLAIM. WHEELOCK'S LIABILITY ON ANY CLAIM OF ANY KIND SHALL CEASE IMMEDIATELY UPON THE
INSTALLATION IN THE PRODUCT OF ANY PART NOT FURNISHED BY WHEELOCK. IN NO EVENT SHALL
WHEELOCK BE LIABLE FOR ANY CLAIM OF ANY KIND UNLESS IT IS PROVEN THAT OUR PRODUCT WAS A DIRECT
CAUSE OF SUCH CLAIM. FURTHER, IN NO EVENT, INCLUDING IN THE CASE OF A CLAIM OF NEGLIGENCE, SHALL
WHEELOCK BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE PRECEDING LIMITATION
MAY NOT APPLY TO ALL PURCHASERS.
/02
P84341 A
Sheet 4 of 4
Loading...