USER’S MANUAL
MANUAL DEL USUARIO
NB-14w2
Notebook Computer
i -1
Notice
The information in this user’s manual is subject to change without notice.
THE MANUFACTURER OR RESELLER SHALL NOT BE LIABLE FOR ERRORS
OR OMISSIONS CONTAINED IN THIS MANUAL AND SHALL NOT BE LIABLE
FOR ANY CONSEQUENTIAL DAMAGES, WHICH MAY RESULT FROM THE
PERFORMANCE OR USE OF THIS MANUAL.
The information in this user’s manual is protected by copyright laws. No part of this
manual may be photocopied or reproduced in any form without prior written
authorization from the copyright owners.
Copyright 6/2006
All rights reserved.
Microsoft and Windows are registered trademarks of Microsoft Corporation. DOS,
Windows 95/98/ME/2000/NT/XP are trademarks of Microsoft Corporation.
Product names mentioned herein may be trademarks and/or registered trademarks
of their respective owners/companies.
The software described in this manual is delivered under a license agreement. The
software may be used or copied only in accordance with the terms of the agreement.
This product incorporates copyright protection technology that is protected by U.S.
patents and other intellectual property rights. Use of this copyright protection
technology must be authorized by Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
.
i -2
TABLE OF CONTENTS
PREFACE
Symbols and Conventions
Protecting Your Computer - Avoid Abusive Handling and Adverse
Environment
Chapter Summaries
1. GETTING TO KNOW THE BASICS
Performance Features (1-2,3)
System at a Glance (1-4)
Top View (1-4,5)
Front View (1-6)
Side Views (1-7,8,9)
Bottom View (1-10,11)
AC Adapter (1-12)
LED Status Indicators (1-13)
OSD Status Indicators (1-14)
Keyboard Features (1-15)
Function (Quick) Keys (1-15)
Windows Keys (1-16)
Embedded Numeric Keypad (1-16)
Touch Pad (1-17)
Graphic Subsystem (1-18)
Adjusting the Display Brightness (1-18)
Extending the Life of the TFT Display Panel (1-18)
Opening and Closing the Display Panel (1-19)
Audio Subsystem (1-20)
Adjusting the Volume in Windows (1-20)
Voice Recording (1-20)
Modem and Modem Setting (1-21,22)
Ethernet Adapter (1-23)
2. BIOS SETUP AND SECURITY
Entering the BIOS Setup Screen (2-3)
Leaving the BIOS Setup Screen (2-3)
i -3
BIOS Action Keys (2-3)
Modifying the BIOS Settings (2-4)
Main Setup (2-4)
Info Setup (2-4)
Advance Setup (2-5)
Security Setup (2-5,6)
Power Setup (2-6)
Boot Setup (2-7)
Exit Setup (2-8)
3. BATTERY POWER & POWER MANAGEMENT
The Battery Pack (3-2)
Lithium-Ion Battery Technology (3-2)
Battery Low-Power Warning (3-3)
Installing and Removing the Battery Pack (3-4,5)
Charging the Battery and Charging Time (3-5)
Checking the Battery Level (3-6)
Prolonging the Battery’s Life and Usage Cycles (3-6)
Using Windows Power Options (3-7)
Windows’ Power Schemes (3-7,8)
Suspend Modes (3-9,10)
Power Button Action (3-11)
Low Battery Warning (3-12)
Power Manual Quick Access (3-13)
4. TROUBLESHOOTING
First Step (4-2,3)
Audio Problems (4-4)
Hard Disk Problems (4-5,6)
Optical Drive Problems (4-7)
Display Problems (4-8)
Keyboard and Mouse Problems (4-9)
CMOS Battery Problems (4-10)
Memory Problems (4-11)
Modem Problems (4-12)
Network Adapter / Ethernet Problems (4-13)
i -4
Performance Problems (4-14)
Firewire (IEEE1394) and USB2.0 Problems (4-15)
Additional Questions (4-16)
APPENDIX A Product Specification
APPENDIX B Agency Regulatory Notices
i -5
Preface
Using This Manual
This User’s Manual contains general information about the
hardware and software setup, troubleshooting, and technical
specifications of the notebook computer.
Symbols and Conventions
The following conventions and symbols are used in this manual:
When keys are to be pressed at the same time, a plus (+)
symbol is used. For instance, Fn+F7 means holding Fn and
F7 keys at the same time.
When a series of clicking actions is needed in Windows O/S, [ ]
and > symbols are used. For instance, [Start > Settings >
Control Panel > Display] means clicking the Start icon first,
then the Settings, then the Control Panel, then the Display
icon.
When you need to make a selection with the touch pad (or
mouse), you will be asked to ’select’ or ‘click’ or ‘double-click’,
‘right-click’ the item.
Note:
Text in this format and symbol means specific instructions, commentary ,
sidelights, or any additional information or notes that you should be aware of.
Warning:
given instructions or information could result in damage to your computer or could
cause bodily harm or loss of life.
Text in this format and symbol means that failures to comply with the
i -6
Protecting Your Computer - Avoid Abusive Handling and
Adverse Environment
Follow the advice below will help ensure that you get the most out
of your Investment.
Your computer will serve you well if you take good care of it.
Do not expose the computer to direct sunlight or place it near
sources of heat.
Do not subject it to temperatures below 0
o
35
C (95oF).
o
C (32oF) or above
Do not expose the computer to magnetic fields.
Do not expose the computer to moisture or rain.
Do not spill water or liquid on the computer.
Do not subject the computer to adverse shock and vibration.
Do not expose the computer to dust and dirt.
Do not place objects on top of the computer to avoid
damaging the computer .
Do not place the computer on rocky surfaces.
Here are some ways of taking care of your AC adapter.
Do not connect the adapter to any devices other than your
computer.
Do not let water get into the adapter .
Do not block the ventilation airway of the adapter.
Keep the adapter in a cool and ventilated place.
Do not step on the power cord or place heavy objects on top
of it.
Carefully tuck away the power cord and any cables away from
pedestrian traffic.
When unplugging the power cord, do not pull on the cord itself
but pull on the plug.
i -7
Keep the adapter away from children.
The total ampere ratings of the equipment plugged in should
not exceed the ampere rating of the cord if you are using an
extension cord.
The total current rating of all equipment plugged into a single
wall outlet should not exceed the fuse rating.
Do not connect other A C a dapter to your notebook. This
Notebook uses exclusively the AC adapter:
(65W), Lishin 0335C2065 (65W), Liteon PA-1650-01 (65W), Liteon
PA-1650-02 (65W), EPS F10653-A(65W)
Lishin 0335A2065
When cleaning the computer, observe these steps:
1. Power off the computer and remove the battery pack.
2. Disconnect the AC adapter.
3. Use a soft cloth dampened with water. Do not use liquid
or aerosol cleaners.
Contact your dealer or see your service technician if any of the
following occurs:
Computer has been dropped or the body has been damaged.
Liquid has been spilled into the product.
The computer does not operate normally.
Cleaning the Ventilation Grills:
It is suggested that you clean the ventilation grills regularly to
maintain optimal thermal regulation of the notebook. To do this, you
may use a soft brush or a vacuum cleaner (with appropriate head
adapter) to remove the dust buildup on the ventilation grills.
i -8
Chapter Summaries
The following is a summary of the available chapters and
appendices in this manual.
Chapter 1: Getting to Know the Basics
In this chapter, you will learn the basic operations and features of
your computer. It gives you a general understanding of the
components of your computer.
Chapter 2: BIOS Setup / Security
In this chapter, you will learn how to cha nge various firmware
settings and what the settings mean. Also, you will learn how to
take advantage of the built-in security feature provided by the
BIOS.
Chapter 3: Battery Power & Power Management
In this chapter, you will learn the fundamentals of power
management and how to use them to achieve longer battery life.
Chapter 4: Trouble sh ooting
In this chapter, you will learn how to solve comm on hardware and
software problems.
Appendix A: Product Specification
In this section, you will find a list of the computer’s system
specifications.
Appendix B: Agency Regulatory Notices
In this section, you will find the general electro-magnetic and safety
regulatory information.
i -9
■ Chapter 1 Getting To Know The Basics
CHAPTER▼ ONE
GETTING TO KNOW THE BASICS
This chapter introduces the features and
components of the computer.
1-1
■ Chapter 1 Getting To Know The Basics
Performance Features
High Performance Processor with ATI Radeon Xpress
200M Chipset
The notebook PC is equipped with a powerful Mobile Intel
Celeron M processor. Together with the ATI chipset and
integrated graphic technologies, the system offers very
advanced PC performances.
Wide-Screen LCD Display
The computer is equipped with a wide-screen 14.1-inch
TFT high-resolution display panel for the best cinematic
viewing experience.
ExpressCard Technology
ExpressCard (type I, 34mm) is the next-generation of the
PC Card standard. The bus interface is based on the two
standards: PCI Express for high-performance I/O and
USB2.0 for variety of devices.
Expandability
The system offers upgradeable hard disk drive and 2 DDRII
SDRAM sockets for expansion, allowing the user to easily
increase the storage and system capacities as the need
arises.
Built-in Multiple Card Reader
There is built-in 4-in-1 card reader to access many of the
portable media formats (SD Card, MS Card, MMC Card,
and MS-Pro Card).
Ethernet Port
The system provides built-in 10/100Mbps Ethernet network
adapter for high bandwidth network connection.
1-2
■ Chapter 1 Getting To Know The Basics
Firewire (IEEE1394 / 1394a) and USB2.0 ports
In addition to a full array of built-in I/O por
ts, the computer
offers IEEE1394 for ultra high-speed connection to high
bandwidth digital video devices and USB2.0 ports to
connect to any USB-based peripheral devices.
Wireless LAN
The internal Wireless LAN module allows your notebook to
connect wirelessly to other 802.11-enabled systems,
devices, or network.
1-3
■ Chapter 1 Getting To Know The Basics
System At A Glance
Top View
1. LCD Display
The panel is where the system content is displayed.
2. LED Status Indicator
The LED Status indicators reveal the status of the system
power state, battery-charging state, Instant-On/Suspend state,
and the WLAN switch enabling and disabling. See the LED
Status Indicator Section for details.
1-4
■ Chapter 1 Getting To Know The Basics
3. Keyboard
The keyboard is used to enter data. (See Keyboard Section for
details.)
4. Touch Pad
The touch pad is a built-in pointing device with functions similar
to a mouse.
5. Built-in Microphone
The built-in microphone records sound.
6. Silent Mode Button
When the system is in Windows, pressing the key enables the
system to lower its power usage; therefore the fan speed is
reduced to achieve lowest operating noise.
When Silent Mode is enabled, the
LED status indicator
shows steady green light.
7. Power / Suspend Button
The power/suspend button turns the notebook on and off and it
also acts as a system suspend key. Press momentarily to turn
on the system. Press and hold for at least 4 seconds to turn off
the system. How this key behaves can be defined in [Start >
Settings > Control Panel > Power Options > Advanced] menu.
Press the power / suspend button again to return from the
suspend mode. (See Chapter 3 for more details on system
suspend function.)
When the system is in Suspend Mode, the
LED status
indicator shows blinking green light.
1-5
■ Chapter 1 Getting To Know The Basics
Front View
Warning:
damage the display
Do not place any heavy objects on the top of notebook. This may
1. Wireless On/Off Switch
Use the Switch to disable or enable the Wireless function.
When Wireless LAN function is enabled, the
indicator shows steady blue light.
2. Ventilation Grill
The fan grill is where air is exchanged to dissipate the internal
heat. Do not block this airway completely.
1-6
LED status
■ Chapter 1 Getting To Know The Basics
Side Views
Warning:
damage the display
Do not place any heavy objects on the top of notebook. This may
1. Optical Drive and Disk Eject Button and Manual Eject Key
Hole
If your computer comes with the Combo drive, DVD-Dual, or
Super-Multi drive, you may save data onto a CD-R / CD-RW or
DVD RW disc. Press the eject button to eject the disk tray. The
manual eject keyhole allows you to manually eject a jammed
disk.
2. External VGA Port
The VGA video output port is for connecting the external LCD
monitor or projector.
3. Power Jack (DC-in)
The DC-out jack of the AC Adapter connects here and powers
the computer.
1-7
■ Chapter 1 Getting To Know The Basics
4. Modem Port
This is where you plug the phone jack (RJ-11) for fax/modem
functions.
5. Kensington Lock Key Hole
A Kensington-type security lock latches to this keyhole for
anti-theft purpose.
6. USB2.0 Port (x3)
The Universal Serial Bus (USB2.0-compliant) port allows you to
connect a wide variety of devices to your computer at a rate of
up to 480 Mbps. This port conforms to the latest USB2.0
plug-and-play standards.
7. Firewire / IEEE1394 / 1394a Port
This is a high-speed serial data port. You may connect any
Fire-wire-ready device to this port.
8. 4-in-1 Card Reader
The 4-in-1 Card Reader supports SD Card, MS Card, MMC
Card, and MS-Pro Card.
9. ExpressCard Slot
The slot is where Express Card (Type I, 34mm) is inserted.
ExpressCard integrates both the PCI-Express bus technology
and USB2.0 interface. Press the card into the slot to insert.
Press the card again to eject.
10. Stereo Headphone / SPDIF-out Jack
The stereo headphone jack (3.5-mm diameter) is where you
connect the headphones or external speakers. Alternatively,
you may connect the SPDIF output to an external DTS, AC3, or
PCM sound processor / decoder in your home stereo system.
11. Microphone/Audio Line-in Jack
The microphone/Audio Line-in jack (3.5-mm diameter) is where
you connect a microphone or an external audio input source
such as a CD player.
1-8
■ Chapter 1 Getting To Know The Basics
12. Ethernet / LAN Port
The port connects to a network hub via the RJ-45 cable and
also conforms to 10/100Base-TX transmission protocol.
13. Ventilation Grill
The fan grill is where air is exchanged to dissipate the internal
heat. Do not block this airway completely.
14. TV (S-Video) Port
The S-Video port permits you to redirect the screen output to a
television set or any analog video playback device. This TV
Port is copyright protected; when DVD movie is played, the
output is scrambled to prevent analog recording.
For certain configuration, this port does not exist or does not
function.
1-9
■ Chapter 1 Getting To Know The Basics
Bottom View
1. Battery Pack and Battery Latch
The battery pack is a built-in power source for the notebook.
Slide the battery latch to release the battery pack.
2. Ventilation Grill
The fan grill is where air is exchanged to dissipate the internal
heat. Do not block this airway completely.
1-10
■ Chapter 1 Getting To Know The Basics
Warning:
surface only. The bottom case may get very hot.
Do not block the Fan Grill outlet. Place the machine on hard
3. System Device Cover
The system’s processor with cooler assembly, Wireless LAN
module, HDD, and DDR memory module are located under the
case cover. Note: opening this door will void the warranty.
4. Built-in Stereo Speakers
The built-in speakers output the sound in stereo.
1-11
■ Chapter 1 Getting To Know The Basics
AC Adapter
1. DC-out Connector
The DC-out connector docks to the power jack (DC-in) on the
computer.
2. Adapter
The adapter converts alternating current into constant DC
voltage for the computer.
3. AC Plug
The AC plug connects to the AC wall outlet.
1-12
■ Chapter 1 Getting To Know The Basics
LED Status Indicator
The LED Status Indicator displays the operating status of your
notebook. When a certain function is enabled, an LED will light
up. The following section describes its indication.
System & Power Status Indicators
LED Graphic
Symbol
Indication
Blue light indicates the WLAN module is
active.
Persistent green light indicates the Silent
Mode is enabled.
Blinking green light indicates the
notebook is in the suspend mode.
Blinking orange light indicates the
battery is being charged.
Blinking green light indicates the battery
power is low when the system is turned
ON.
Persistent green light indicates the
system is turned ON.
1-13
■ Chapter 1 Getting To Know The Basics
OSD Status Indicator
The On-screen Status Display Indicator displays the operating
status of your notebook. When a certain function is enabled,
the symbol will show up on windows. The following section
describes its indication.
OSD Status Indicators
Action Graphic Symbol
Fn + F3: Audio Mute
Fn + F5: Audio
Volume U p
Fn + F6: Audio
Volume Down
Fn + F7: Display
Brightness Up
Fn+ F8: Display
Brightness Down
Fn + Num Lock:
Numeric Keypad is
Caps Lock:
Capitalization is On
Scroll Lock: Scroll
Lock is On
1-14
■ Chapter 1 Getting To Know The Basics
Keyboard Features
Function Keys (Quick Keys)
Graphic
Symbol
Action System Control
Fn + F1 Enters Suspend Mode.
Fn + F3 Turns of the battery warning
beep off or on.
Fn + F4 Changes Display Mode:
Fn + F5 Turns Speaker Volume up.
Fn + F6 Turns Speaker Volume down.
Fn + F7 Increases Display Brightness.
Fn + F8 Decreases Display Brightness.
Fn+Num Lk Enables the embedded keypad
Caps Lock When Caps lock is enabled, all
Fn + Scr Lk Press the Fn+Scr Lk key and
LCD-only, CRT-only and
LCD&CRT.
to work in numeric mode. The
keys act like numeric keypads
in a calculator. Use this mode
when you need to do a lot of
numeric data entry. An
alternative would be to connect
an external numeric keypad.
the characters you enter
become capitalized.
then press ↑or ↓to move one
line up or down.
1-15
■ Chapter 1 Getting To Know The Basics
Windows Keys
Your keyboard also has two Windows keys:
1. Start Key
This key allows you to pull up the Windows Start Menu at
the bottom of the taskbar.
2. Application Menu Key
This key brings up the popup menu for the application,
similar to a click of the right mouse button.
Embedded Numeric Keypad
Press Fn + Num Lk to enable the embedded numeric keypad.
The numbers are printed in upper right corner of a key, in a
color different from the alphabets. This key pad is complete
with arithmetic operators (+, -, * , /).
Press Fn+Num Lk to revert to normal character keys.
1-16
■ Chapter 1 Getting To Know The Basics
Touch Pad
The built-in touch pad, which is a PS/2-compatible pointing device,
senses movement on its surface. As you move your fingertip on the
surface of the pad, the cursor responds accordingly.
The following items teach you how to use the touch pad:
1. Move your finger across the touch pad to move the cursor.
2. Press buttons to select or execute functions. These two buttons
are similar to the left and right buttons on a mouse. Tapping on
the touch pad twice produces is similar to clicking the left button
of a mouse.
Function Left Button Right
Execution Click twice
quickly
Selection Click once Tap once
Drag Click and hold
Access
Context Menu
Move One
Page Up or
Down
to drag the
cursor
Click once
Button
Tap twice (at the same speed as
Tap twice quickly and on the
Tips on Using the Touch Pad:
1. The double-click speed is timed. If you double-click too slowly,
your notebook responds as if you single-clicked twice.
2. Keep your fingers dry and clean when using the touch pad.
Also keep the surface of touch pad clean and dry to prolong its
life.
3. The touch pad is sensitive to finger movements. Hence, the
lighter the touch, the better the response. Heavy touch does
not produce better response.
Equivalent Tapping Action
double-clicking
the mouse button)
second tap hold finger to the touch
pad to drag the cursor
1-17
■ Chapter 1 Getting To Know The Basics
Graphic Subsystem
Your computer uses a high performance 14.1-inch active matrix
TFT panel with high resolution and multi-million colors for
comfortable viewing. The ATI Radeon Xpress 200M integrated
video graphics accelerator, which is Microsoft DirectX 9 compatible,
performs graphic rendering at a lighting-fast speed.
Adjusting the Display Brightness
The notebook uses special key combinations, called hot keys,
to control brightness.
Press Fn+F7 to increase the brightness.
Press Fn+F8 to decrease the brightness.
Note: To maximize your battery operating time, set the brightness to the
lowest comfortable setting, so that the internal backlight uses less power.
Extending the Life of the TFT Display Device
Observe the following guidelines to maximize the life of the
backlight in the display.
1. Set the brightness to the lowest comfortable setting
(Fn+F8).
2. When working at your desk, connect your notebook to an
external monitor and disable the internal display Fn+ F4.
3. Do not disable the suspend time-outs.
4. If you are using AC power and have no external monitor
attached, change to suspend mode when not in use.
1-18
■ Chapter 1 Getting To Know The Basics
Opening and Closing the Display Panel
To open the display, lift up the lid. Then tilt it to a comfortable
viewing position. The LCD panel has a maximum opening of
135 degrees. Do not push it down forcibly.
To close the display cover, fold it down gently.
Warning:
place any object on top of the computer when the display is closed
To avoid damaging the display, do not slam it when closing. Do not
1-19
■ Chapter 1 Getting To Know The Basics
Audio Subsystem
Your computer’s audio subsystem is Sound Blaster Pro-compatible.
Adjusting the Volume Manually
To increase the volume, press Fn+F5.
To decrease the volume, press Fn+F6.
Adjusting the Audio Volume in Windows
1. Click the speaker symbol in the task tray in Windows.
2. Drag the volume control bar up or down to adjust the
volume.
3. To temporarily silence the speaker without changing the
volume setting, click Mute.
Voice Recording
A built-in microphone allows you to record sound. You will need
to use audio processing software to enable the built-in
microphone. For example, you may use Microsoft Sound
Recorder.
1-20
■ Chapter 1 Getting To Know The Basics
Modem
Your computer comes with a 56K V.92 internal fax/modem and a phone
jack (RJ-11), which is located on the left side of your computer.
Use a telephone cable to connect the computer to the telephone wall
outlet.
For certain configuration, there is no Modem Port or Function.
Note:
Connecting the Modem
1. Plug one end of the phone line into the modem port located on
the rear side of the computer. (For EMI compliance, you need
to clip the included EMI CORE to the phone line.)
2. Plug the other end of the line into the analog phone wall outlet.
Depending on where your computer is used, you may need to change
settings in the modem. Correct setting will allow you to maintain a stable
connection in a country where its telecommunication system may be
different to others.
To change the modem setting, do the following:
1. Go to [Start > Settings > Control Panel > Phone and
Modem Options]. Go to Dialing Rules and Edit My Location.
You will see a similar dialog box.
1-21
■ Chapter 1 Getting To Know The Basics
2. Click on the pull-down menu and select the country where it is
applicable. Click on OK to exit.
1-22
■ Chapter 1 Getting To Know The Basics
Ethernet
Your computer is equipped with a 10/100Base-TX Fast Ethernet
network adapter. Connect the active LAN cable to the RJ-45 LAN
port located on the left side of the computer. This allows you to
access and transmit data in the local area network.
Connecting to the Network
Use Unshielded Twisted Pair (UTP) Ethernet cable only.
1. Insert one end of the UTP cable into the network connector
until the connector snaps securely into the receptacle.
2. Either connect the other end of the cable to an RJ-45 jack
wall outlet or to an RJ-45 port on a UTP concentrator or
hub in the network.
Cabling Restriction for Networks
The following restrictions should be observed for
10/100BASE-TX networks:
The maximum cable run length is 100 meters(m) (328
feet[ft]).
Note:
Consult Windows manual and / or Novell Netware user’s guide for the
software installation, configuration, and operation of the network.
1-23
■ Chapter 2 Bios Setup and Security Feature
CHAPTER▼ TWO
BIOS SETUP AND SECURITY FEATURE
In this chapter, you will learn how to
enter the BIOS Setup Menu and
manipulate various hardware control
settings. You will also learn how to use
the built-in security features.
2-1
■ Chapter 2 Bios Setup and Security Feature
The Setup Utility is a hardware configuration program built into
your computer’s BIOS (Basic Input/Output System). It runs and
maintains a variety of hardware functions. It is a menu-driven
software, which allows you to easily configure and change the
settings.
The BIOS contains manufacture’s default settings for the
computer’s standard operations. However, there are occasions
when you may be required to modify the default settings in the
BIOS.
The BIOS allows you to set up passwords to limit access to users.
This is an important feature because a great deal of vital
information is carried within the computer nowadays. Unauthorized
access can be prevented. Later in this chapter, you will learn how to
use this security feature.
2-2
■ Chapter 2 Bios Setup and Security Feature
Entering the BIOS Setup Screen
First turn on the power. When the BIOS performs the POST
(Power-On Self Test), press F2 key quickly to activate the Pheonix
BIOS Setup Utility.
Note:
You may need to press F2 key fairly quickly. Once the system begins to load
Windows, you may have to retry by cycle-power on again
Leaving the BIOS Setup Screen
When you have finished modifying the BIOS settings, exit the BIOS.
It takes a few seconds to record changes in the CMOS.
BIOS Action Keys
Function Key Command Description
Leaves a sub-menu to return to the
ESC Exit
previous menu OR exits the BIOS setup
while saving changes.
Enter Go to Sub Screen Shows the Sub Menu
F1 General Help Shows the Help Screen
F9 Setup Defaults Load default values
F10 Save and Exit
<Tab> Select a field Selects the next field.
↑ Select an item Selects the next upper item.
↓ Select an item Selects the next lower item.
- Lower value Selects the next value within a field.
+ Higher value Selects the next value within a field.
Saves changes and reboots the
computer.
2-3
■ Chapter 2 Bios Setup and Security Feature
Modifying the BIOS Settings
The Phoenix BIOS setup main menu is subdivided into sub-menus.
Each menu item is described in this section.
Main Setup
Under this menu, you may change time/date and view basic
processor and system memory information.
Item Selections /
Sub-menu
System
Time
System
Date
N/A Type in the current date, in HH:MM:SS
N/A Type in the current date, in MM/DD/YY
Description
format.
format.
Info Setup
Item Description
BIOS Information:
BIOS Version: 1.00
KBC Version: 1.00
Processor:
CPU Type Genuine Intel® CPU
CPU Info Intel Celeron M inside
Display BIOS version and CPU
Information
2-4
■ Chapter 2 Bios Setup and Security Feature
Advanced Setup
Item Selections /
Sub-menu
Execute
Disable Bit
Quiet Boot Disabled
TouchPad
Support
Disabled
Enabled
Enabled
Enabled
Disabled
Description
When enabled, this unique feature
protects against certain type of virus that
creates Buffer Overflow problem in the
memory subsystem.
When Disabled, the system will display
OEM logo instead of the POST
messages.
When Enabled, the system will display
POST messages (i.e. devices
information.)
Enable or disable the built-in touchpad.
Security Setup
Item Selections /
Sub-menu
Set
Supervisor
Password
Set User
Password
Password
on Boot
N/A Install or Change the Password
N/A Install or Change the Password
Disabled
Enabled
Description
When enabled, the system will always
ask for User Password on boot.
Using Password Protection
Two Levels of Password Protection are available. The BIOS
2-5
■ Chapter 2 Bios Setup and Security Feature
provides both a Supervisor and a User password. If you try to
activate both passwords, the Supervisor password must be set first.
The passwords activate two different levels of protection:
1. System always asks for password every time it is powered on.
2. System asks for password only when you attempt to enter
BIOS utility.
The passwords are encrypted and stored in NVRAM. Make sure
you write them down or memorize them. If you lost the passwords,
the computer may need to be sent back to the factory or to an
authorized service dealer to reset the passwords.
Power Setup
Item Selections /
Sub-menu
LCD Panel
Power Saving
Long Battery
Life Mode
Enable
Disable
Enable
Disable
Description
When Enabled (system is powered by
battery), the system will automatically
adjust the LCD brightness to save
power.
When Enabled, maximum battery life
can be achieved. The processor
performance is lowered.
Note:
In Windows ME / 98SE / 2000 / XP, suspend mode and settings are
determined by settings in the Power Options Properties (Start > Control Panel >
Power Options).
2-6
■ Chapter 2 Bios Setup and Security Feature
Boot Setup
►Boot Settings Configuration
Item Selections /
Sub-menu
LAN
Remote
Disabled
Enabled
Boot
►Boot Device Priority
Item Selections /
Sub-menu
USB Key
USB FDC
USB CDROM
USB HDD
IDE CD
IDE HDD
PCI BEV
Realtek Boot
Agent
Description
When enabled, the system can support
remote wake-up or boot on LAN.
Description
Set the priority of bootable devices that
the BIOS attempts to boot from.
For example, if you wish to boot from an
external USB CDROM with a bootable
disc in it, you may want to put USB
CDROM to the top of the priority list.
Note:
IDE CD means the system’s built-in optical drive. IDE HDD means the
system’s built-in HDD. PCI BEV is the Realtek Boot Agent, which allows you to boot
from the Network.
Note: When the BIOS performs POST, you may also press Enter Key to enable the
Boot Device selection menu. You may choose CD/DVD, Hard Drive, or Realtek Boot
Agent as the first storage device to boot from. If you have already connected a USB
Floppy Disk Drive before powering up, it will appear as a USB FDC in the Boot
Device selection menu
2-7
■ Chapter 2 Bios Setup and Security Feature
Exit Setup
Item Selections /
Sub-menu
Saves
N/A After you have completed the BIOS
Changes and
Exit
Discard
N/A Discards changes done so far to any of
Changes and
Exit
Get Default
N/A Load Optimal Default value for all the
Values
Load Previous
N/A Load settings that you made during the
Values
Description
settings, select this item to save all
settings, exit BIOS Setup utility, and
reboot. New system settings will take
effect on next power-up. F10 key can be
used for this operation.
the setup questions and exit.
setup questions. F9 key can be used for
this operation.
previous BIOS Setup session.
2-8
■ Chapter 3 Battery Power & Power Management
CHAPTER▼ THREE
BATTERY POWER & POWER
MANAGEMENT
In this chapter, you will learn the
fundamentals of power management
and how to use it to achieve longer
battery life.
3-1
■ Chapter 3 Battery Power & Power Management
In this chapter, you will learn how to operate your notebook on
battery power, how to handle and maintain the battery pack, and
learn about the system’s power saving features.
TFT display, central processor, hard disk drive are the major
hardware subsystems that consume the most power. Power
management deals how these key components should behave to
conserve power . For example, you can have the system turn off its
display after 2 minutes of inactivity to save power. Efficient power
management can help you work longer sessions before having to
recharge the battery.
The Battery Pack
Lithium-Ion Battery
Your notebook uses a six-cell Lithium-Ion battery pack
that provides power when you don’t have access to an
AC outlet.
3-2
Note:
It is necessary that you charge the battery pack for at least 6
hours before using it for the first time.
Note: In the Standby Suspend mode, a fully charged battery loses its
power in roughly 1/2 day or less. When not being used, the battery’s
power will deplete in 1-2 month.
■ Chapter 3 Battery Power & Power Management
Battery Low-Power Warning
1. Low Battery Warning
Low battery condition occurs when battery power is
reduced to 6%. The green battery status LED
indicator blinks and the system beeps once every
16 seconds or so.
2. Very Low Battery Warning
Very Low battery condition occurs at 3 % power
remaining. The green battery status LED indicator
blinks and the system beeps at 4-second interval.
When the notebook warns you of its low battery
condition, you will have about 3-5 minutes to save
your current work.
Warning:
degree Celsius (32 degree F) or above 60 degree C (140F). This may
adversely affect the battery pack.
Do not expose battery packs to temperatures below 0
Note:
Press Fn+F3 to turn off the battery warning beep.
3-3
■ Chapter 3 Battery Power & Power Management
Installing and Removing the Battery Pack
To Remove the Battery Pack:
1. Place the notebook bottom-side up on a flat and
secured surface.
2. Push the latch and pull the battery’s hard case
away from the notebook.
3-4
■ Chapter 3 Battery Power & Power Management
To Install the Battery Pack:
1. Place the notebook bottom-side up on a flat and
secured surface.
2. Carefully insert the battery pack into the battery
compartment of the notebook.
Charging the Battery and Charging Time
To charge the battery, while the battery pack is in the noteboo k,
plug the AC adapter into the notebook and an electrical outlet.
The charging time is approximately 4-6 hours when the
notebook is turned off and approximately 6-10 hours when the
notebook is turned on.
When the battery is fully charged, the battery charge indicator
becomes green.
If system runs at heavy loading or in a high temperature environment,
Note:
the battery may not be fully charged. You need to continue to charge it with the
AC adapter plugged in until the charging LED turns green.
3-5
■ Chapter 3 Battery Power & Power Management
Checking the Battery Level
You can check the remaining battery power in the Windows
battery status indicator , which is lo cated at the lower right-ha nd
corner of the task bar . (If you do not see a battery or AC-in icon
on the task tray, go to Power Options Properties box and click
on the Advanced tab. Check of f ``Always show icon o n the task
bar``.)
Alternatively, you can access the power meter by clicking the
Power Options icon in the Windows Control Panel.
Prolonging the Battery’s Life and Usage Cycles
There are ways you can do to prolong the use of battery.
Use the AC adapter wherever AC wall outlet is available.
This will ensure uninterrupted computing.
Purchase additional battery pack.
Store the battery pack in room temperature. Higher
temperature tends to deplete the battery’s power faster.
Make good use of the power management function. Save
To Disk (Hibernate) saves the most energy by storing
current system contents in a hard disk space re served for
this function.
The life expectancy of the battery is approximately 300
recharges.
See the notices section in the beginning of the user
manual on how to care for the battery pack.
Note:
Read Section Protecting Your Notebook in the beginning of this manual
for tips about how to maintain the battery pack.
Note: To achieve optimal battery performance, you may need to do a battery
calibration at a 3-month interval. To do this:
1. Fully charge the battery.
2. Then discharge the battery by entering the BIOS setup screen. (Press F2
key as soon as you turn on the computer. And let it remain at the setup screen
until the battery runs out.
3. Fully charge the battery again.
3-6
■ Chapter 3 Battery Power & Power Management
Using Windows Power Options
Windows Power Management provides basic power saving
features. In the Windows Power Options Properties [Start >
Settings > Control Panel > Power Options] dialogue box, you
may enter time-out values for display and hard disk drive.
Windows power manager saves power by turning off hard drive
after 1 minute of inactivity, for example.
Windows’ Power Schemes
The power management control panel in Windows XP,
known as Power Schemes, is designed to provide the
user with an easy-to-use interface. The Power Schemes
tab can be found in the Power Options Properties panel
that is accessible via the control panel window.
Schemes are easy to understand, based on notebook
usage scenarios, and control not only processor power
usage but other system peripherals as well.
Go to [Start > Settings > Control Pan el] and double-click
the Power Options icon.
Always on mode puts the processor into maximum
performance mode, which provides no power saving.
The other schemes control processor performance
based on demand. For example, Max Battery mode
lowers the processor’s speed and voltage to conserve
power as much as possible.
3-7
■ Chapter 3 Battery Power & Power Management
In this dialog box, you can manually set the LCD and
hard drive’s time-out values in the Plugged in colu mn and
in the Running on batteries column. Lower time-out
values will save more battery power.
3-8
Note:
Also consult Windows user guide for more information on how
to use Windows power management functions.
Note: Actual dialogue box shown above may appear slightly different.
■ Chapter 3 Battery Power & Power Management
Suspend Mode
Standby Suspend
The system automatically enters this mode after a period
of inactivity, which is set in the Power Schemes dialog
box. In Standby mode, hardwa re devices, such as
display panel and hard disk, are turned off to conse rve
energy.
Hibernate Suspend
In this mode, all system data are saved in the hard disk
before powering down. When this mode is activated, all
system state and contents are saved to the hard disk
drive after a period of inactivity defined by the user. No
power or very little power is drawn from the battery
module under this mode.
However, depending on how much RAM that have been
installed on your computer, the amount of time the
system requires to restore all its previous contents can
range from 5 to 20 seconds.
For Windows 2000 / XP users, hibernation is handled by
the operating system; therefore, no special disk partition
or disk file is necessary.
If you wish to activate Hibernate mode, you need enable
Hibernate Support in the Hibernate tab of the Power
Options menu.
3-9
■ Chapter 3 Battery Power & Power Management
3-10
Note:
Do not install or remove the memory module when the system
is in the suspend mode.
Note: Actual dialogue box shown above may appear slightly different.
■ Chapter 3 Battery Power & Power Management
Power Button Action
The notebook PC’s power button can be set to turn of f
the system or activate the suspend mode.
Go to [Start > Settings > Control Panel > Power Options]
and click on the Advanced tab. In the pull-down menu,
select how you wish the power button to work as.
Note:
Actual dialogue box shown above may appear slightly different.
Warning:
pull-down menu, DO NOT select Do nothing – otherwise the system will
still run at high speed while the processor’s fan grill is fully blocked by
the closed LCD panel. The heat will damage the LCD panel.
In the When I close the lid of my portable computer
3-11
■ Chapter 3 Battery Power & Power Management
Low Battery Warning
You can define when and how the system warns you of
its battery-low condition.
Go to the Alarms tab in the Power Options Properties box.
If you wish to hear audible beeps, click on the Alarm
Action button and put a check on Sound Alarm.
3-12
Note:
Consult Windows user guide for more information on how to
use Windows power management functions.
Note: Actual dialogue box shown above may appear slightly different.
■ Chapter 3 Battery Power & Power Management
Power Menu Quick Access
Instead of making specific selections in the Power
Options Properties box, you can quickly and easily
specify which pre-set power saving function you desire
by clicking on the Battery icon at the lower right-hand
corner of the task bar. (If you do not see a battery or
AC-in icon, go to Power Options Properties box and click
on the Advanced tab. Check off ``Always show icon on
the task bar``.) Select Max Battery if you want the system
to enter suspend mode more often. Or, select Always On
if your notebook PC is plugged into an AC power source.
Actual dialogue box shown above may appear slightly different.
Note:
3-13
■ Chapter 4 Troubleshooting
CHAPTER▼ FOUR
TROUBLESHOOTING
In this chapter, you will learn how to
solve common hardware and software
problems.
4-1
■ Chapter 4 Troubleshooting
Your computer has been fully tested and complies with the
system specifications before shipping. However, incorrect
operations and/or mishandling may cause problems.
This chapter provides a reference for identifying and correcting
common hardware and software problems that you may encounter.
When you encounter a problem, you should first try to go through
the recommendations in this chapter. Instead of returning the
computer and waiting for repair, you may easily solve the problems
by considering the following scenarios and possible solutions. If the
error continues, contact technical support at (866) 287-55 55.
Before taking further actions, consider the following
suggestions:
Check to see if the problem persists when all the external
devices are removed.
Check to see that the green light indicator on the AC adapter
is lit.
Check to see the power cord is properly plugged to the wall
outlet and to the computer.
Check to see the power indicator of the computer is on.
Check to see if your keyboard is operational by pressing and
holding any key.
Check for any incorrect or loose cable connections. Make
sure the latches on the connectors latch securely on to the
receptor end.
Be sure you have not performed an incorrect setting on the
hardware devices in the BIOS Setup utility. A faulty setting
may cause the system to misbehave. If you are not sure of the
4-2
■ Chapter 4 Troubleshooting
changes you made, try to restore all the settings to factory
defaults.
Be sure all the device drivers are installed properly. For
example, without the audio driver properly installed, the
speakers and microphone will not work.
If external devices such as USB camera, scanner, and printer
do not function correctly when connected to the system, it is
usually the device’s own problem. Consult the device’s
manufacturer first.
Some software programs, which have not gone through
rigorous coding and testing, may cause problems during your
routine use. Consult the software vendor for problem solving.
Legacy peripheral are not plug-and-play capable. You need to
restart the system with these devices powered up and
connected first.
Be sure to go to BIOS SETUP and load DEFAULT SETTING
after BIOS re-flash.
Contact technical support, 24 hours a day, 7 days a week, at
(866) 287-5555.
4-3
■ Chapter 4 Troubleshooting
Audio Problems
No speaker output -
Software volume control is turned down in Microsoft
Sound System or is muted. Double-click the speaker icon
on the lower right corner of the taskbar to see if the
speaker has been muted or turned down all the way.
Most audio problems are software-related. If your
computer worked before, chances are software may have
been set incorrectly.
Go to [Start > Settings > Control Pan el] and double-click
the Sounds and Audio Devices icon. In the Audio page,
make sure that Realtek HD Audio is the default playback
device.
Sound cannot be recorded -
You will need to plug-in an external microphone to the
microphone connector to record sound.
Double-click the speaker icon on the lower right corner of
the taskbar to see if the microphone has been muted.
1. Click Options and select Properties.
2. Select Recording and click the OK button.
3. After Click OK button, the recording volume co ntrol
panel will appear.
Go to [Start > Settings > Control Pan el] and double-click
the Multimedia icon (or Sounds and Audio Devices icon).
In the Volume or Audio page, make sure that Realtek HD
Audio is the default recording device.
4-4
■ Chapter 4 Troubleshooting
Hard Disk Problems
The hard disk drive does not work or is not recognizable -
The new HDD may need to be partitioned and reformatted.
O/S and drivers will need to be re-installed as well.
Check the hard disk indicator LED. When you access a
file, the LED lamp should light up momentarily.
The new HDD may be defective or is not compatible.
If your computer has been subjected to static electricity or
physical shock, you may have damaged the disk drive.
The hard drive is making abnormal whining noises -
You should back up your files as soon as possible.
Make sure the source of noise is indeed from the hard
drive and not the fan or other devices.
The hard disk drive has reached its capacity -
Run Disk Cleanup utility in Windows. [Start > All Prog rams
> Accessories > System Tools > Disk Cleanup] The
system will prompt you for what to do.
Archive files or programs that you had no longer used by
moving them to an alternative storage medium (floppy
disk, optical record-able disk, etc.) or uninstall programs
that no longer use.
Many browsers store files in the hard drive as a cache to
speed up the performance. Check the program’s Online
Help for instructions on decreasing the cache size or on
removing temporary Internet files.
Empty the Recycle Bin to create more disk space. When
you delete files, Windows saves them to the Recycle Bin.
4-5
■ Chapter 4 Troubleshooting
The hard disk takes longer to read a file -
If you have been using the drive for a period, the files may
be fragmented. Go to [Start > Programs > Acce ssories >
System Tools > Disk Defragmenter] to perform a disk
defragmentation. This operation may take a while.
Interrupt requests or problems with other hardware
devices may have occupied the CPU and therefore slows
down the system performance.
The files are corrupted -
Run the Error-checking utility in Windows to check the
HDD. Double-click My Computer . Right-cli ck C: and select
Properties. Click Check Now in Error- checking in Tools.
4-6
■ Chapter 4 Troubleshooting
Optical Drive Problems
The optical drive does not work -
Try rebooting the system.
The disk is damaged or files are not readable.
After you have inserted a CD-ROM di sk, it may take a
moment before you can access its content.
The drive dose not read any disks -
The CD may not be properly seated in the tray. Make
sure the disk is firmly seated onto the spindle.
The disk is damaged or not readable.
The disk cannot be ejected -
Normally, it takes a few seconds to eject the disk.
If the disk cannot be ejected, it may be mechanically
jammed. Straighten out a paper clip and insert it to a tiny
hole next to the eject button. This should reject the disk
tray. If not, return the unit for repair. Do not forcefully pull
on the disk tray.
The Combo or DVD Dual cannot record -
You need to purchase and install a burner utility program
to record files to a blank media.
4-7
■ Chapter 4 Troubleshooting
Display Problems
The display panel is blank when the system is turned on -
Make sure the computer is not in the Standby or
Hibernate suspend modes. The display is turned off to
conserve energy in these modes.
The screen is difficult to read -
The display resolution should at least be set to at
least1024x768 for optimal viewing.
Go to [Start > Settings > Control Pan el] and double-click
the Display icon.
Under the Settings page, set screen resolution to at least
1024x768 and choose at least 256 colors.
The screen flickers -
It is normal if the display flickers a few times during
shutting down or powering up.
4-8
■ Chapter 4 Troubleshooting
Keyboard and Mouse Problems
The built-in touch pad performs erratically
Make sure there is no excess perspiration or humidity on
your hand when using the touch pad. Keep the surfa ce of
the touch pad clean and dry.
Do not rest your palm or wrist on the surface of the touch
pad while typing or using the touch pad.
The built-in keyboard accepts no input -
If you are connecting an external keyboard to the system,
the built-in keyboard may not work.
Try restarting the system.
The characters on the screen repeat while I type.
You may be holding the keys down too long while you’re
typing.
Keep the keyboard clean. Dust and dirt under the keys
could cause them to stick.
Configure the keyboard to wait longer before the auto
repeat feature starts. To adjust this feature, Go to [Start >
Settings > Control Panel], and double-click the Keyboard
icon. A dialogue box shows up with the adjustable
settings for the keyboard.
4-9
■ Chapter 4 Troubleshooting
CMOS Battery Problem
A message “CMOS Checksum Failure” displays during the
booting process or the time (clock) resets when booting -
Try to reboot the system.
If the message “CMOS Checksum Failure” appears
during the booting procedure even after rebooting, it may
indicate failure of the CMOS battery. Please call our
service center for troubleshooting at (866) 287-5555.
4-10
■ Chapter 4 Troubleshooting
Memory Problems
The POST does not show an increased memory capacity
when you have already installed additional memory -
Certain brands of memory module may not be
compatible with your system. You should ask your vendor
for a list of compatible DIMM.
The memory module may be defective.
The O/S issues an insufficient memory error message
during operation -
This is often a software or Windows-rela ted problem. A
program is draining the memory resources.
Close the application programs you’re not using and
restart the system.
4-11
■ Chapter 4 Troubleshooting
Modem Problems
The built-in modem does not respond -
Make sure the modem driver is loaded properly.
Go to [Start > Settings > Control Pan el > Phone and
Modem Options] and go to Modems tab. Make sure
Motorola SM56 Data Fax Modem is listed. Otherwise,
click the Add button to add the modem drive, which is
located in the factory CD-ROM (or floppy diskette).
Go to [Start > Settings > Control Panel > System] and
click Device Manager button in the Hardware page to
check for possible resource or driver conflict. See
Windows on-line help or manual for how to handle such
problems.
Make sure the phone line, which the computer is
connected to, is working.
Connection difficulties -
Be sure to disable Call Waiting on the phone line.
Be sure to have the correct country setting where your
computer is used. Go to [Start > Settings > Control Panel
> Phone and Modem Options]. Go to Dialing Rules and
Edit My Location. In the Country/Region pull-down menu,
select the appropriate country setting.
Excessive line noise might cause the connection to be
dropped. To check this, put the regular phone handset on
the line and placing a phone call. If you do hear abnormal
noise, try to make the modem connection with a different
line or contact your local telephony company for service.
Make sure the cable connection is firm.
Try a different receiver number and see if the problem
persists.
4-12
■ Chapter 4 Troubleshooting
Network Adapter / Ethernet Problems
The Ethernet adapter does not work -
Go to [Start > Settings > Control Panel > System >
Hardware > Device Manager]. Double-click on Network
Adapters and check if Realtek RTL8139/810x Family
Fast Ethernet NIC appears as one of the adapters. If it
does not exist, Windows has not detected the Realtek
RTL8139/810x Family Fast Ethernet NIC or the device
driver has not been installed properly. If there is a yellow
mark or red-cross on the network adapter , it may be a
device or resource conflict. Replace or update the device
driver from the factory CD-ROM disk or consult Windows
manual on how to solve the resource conflict problem.
Make sure the physical connections on both ends of the
cable are good.
The hub or concentrator may not be working properly.
Check to see if other workstations connected to the same
hub or concentrator is working.
The Ethernet adapter does not appear to operate in the
100Mbps transmission mode -
Make sure the hub you are using supports 100Mbp s
operation.
Make sure that your RJ-45 cable meets the 100Base-TX
requirements.
Make sure the Ethernet cable is connected to the hub
socket that supports 100Base-TX mode. The hub may
have both 10Base-TX and 100Base-T sockets.
4-13
■ Chapter 4 Troubleshooting
Performance Problems
The computer becomes hot -
In a 35
computer’s back case are expected to reach 50 degrees.
Make sure the air vents are not blocked.
If the fan does not seem to be working at high
temperature (50 degrees Celsius and up), contact the
service center.
Certain programs that are processor-intensive may
increase the computer temperature to a degree where
the computer automatically slows down its CPU clo ck to
protect itself from thermal damage.
The program appears stopped or runs very slowly -
Press CTRL+ALT+DEL to see if an application is still
responding.
Restart the computer.
This may be normal for Windows when it is processing
other CPU-intensive programs in the background or
when the system is accessing slow-speed devices such
the floppy disk drive.
You may be running too many applications. Try to close
some applications or increase system memory for higher
performance.
The processor may have been overheated due to the
system’s inability to regulate its internal heat. Make sure
the computer’s ventilation grills are not blocked.
o
C environment, the certain areas of the
4-14
■ Chapter 4 Troubleshooting
Firewire (IEEE1394) and USB2.0 Problems
The USB device does not work -
Windows NT 4.0 does not support USB protocols
Check the settings in the Windows Control Panel.
Make sure you have installed the necessary device
drivers.
Contact the device vendor for additional support.
The IEEE1394 port does not work -
Go to [Start > Settings > Control Panel > System >
Hardware > Device Manager]. You should see an entry
which reads “OHCI Compliant IEEE 1394 Host
Controllers”. If it does not exist, Windows has not
detected the host controller or the device driver has not
been installed properly. If there is a yellow mark or
red-cross on the 1394 host controller, it may be a device
or resource conflict. Replace or update the device driver
from the factory CD-ROM disk or consult Windows
manual on how to solve the resource conflict problem.
Make sure the cable is fully connected.
Make sure you have installed the necessary device
drivers.
Contact the device vendor for additional support.
4-15
■ Chapter 4 Troubleshooting
Additional Questions
See our website at www.westinghousedigital.com.
Contact Westinghouse Digital Customer Service at
(866) 287-5555 or write us service@westinghousedigital.com
.
4-16
■ Appendix A Product Specification
A
APPENDIX▼ A
PRODUCT SPECIFICATION
-1
■ Appendix A Product Specification
A
▼ Processor and Core Logic
Processor
Core Logic
Mobile Intel Celeron M Processor (Yonah), up to
1.73GHz, 1MB L2 cache
ATI RC410MD + ATI SB460 chipset with graphic, audio,
modem, and USB2.0 controllers integrated
533MHz Front Side Bus
533 / 667MHz DDR2 interface
▼
System Memory
Memory Type
Default
Memory
Expansion
DDR2 SDRAM 533 / 667
256 / 512 / 1024MB
Two 200-pin DIMM sockets, Max 2 GB
▼
Display
LCD Panel
Graphic
Accelerator
Motion
Playback
Other
Features
14.1-inch Wide-Viewing-Angle WXGA TFT LCD
ATI RC410MD Integrated Graphic Engine
Hardware Motion Compensation and IDCT Supported
for MPEG1/2 Playback
DirectX compatible
-2
■ Appendix A Product Specification
A
▼ Audio
Chipset
Audio Codec
Sound
Capabilities
ATI SB460 integrated audio controller
Realtek Audio Codec
DirectSound 3D, EAX 1.0 & 2.0 compatible
A3D, I3DL2 compatible
AC97 V2.3 compatible
Azalia compatible
2 Stereo Speakers
▼
Modem
Chipset
Transmission
Rate
ATI SB460 integrated Modem Controller with MDC
card, support 56K MDC Modem Card with Azalia
standard
V.92 / V.90 / K56flex for download data speed up to
56Kbps.
V.34, V.17, V.29 protocol supported
▼
Wireless LAN
Module
Transmission
Protocol
MSI (RALink) MS-6877 Card
Mini-Card Interface IEEE802.11 B&G
-3
■ Appendix A Product Specification
A
▼ LAN / Ethernet
Chipset
PnP Function
Flow Control
Speed
Selection
Other
Features
Realtak RTL8100CL Ethernet function for
10/100Base-TX network standards
Windows XP Plug and Play compatible
Automatic Jam and auto-negotiation for flow control
Auto Negotiation and Parallel detection for automatic
speed selection (IEEE 802.3u)
High performance 32-bit PCI bus master architecture
with integrated DMA controller for low CPU and bus
utilization
Remote Wake-up Scheme supported
Hot Insertion supported
▼
Firewire IEEE1394(a)
Chipset
Capabilities
02 Micro 0Z128 IEEE1394 OHCI Host Controller
Up to 400 Mbps
Expandable up to 63 devices in chains
▼
Storage
Hard Drive
Combo Drive
DVD-Dual or
DVD-Multi
Standards
S-ATA 2.5-inch format hard disk drive
-4
■ Appendix A Product Specification
A
▼ Keyboard & Touch pad
Keyboard
Touch pad
86/87-key QWERTY keyboard with numeric keypad
and Windows keys, 19.05mm Pitch
Built-in Touch Pad
▼
ExpressCard (NewCard) & Multiple
Card Reader
Chipset
Express Card /
New Card
4-in-1 Card
Reader Format
Support
Mic-In/Audioin Port
Audio-Out / SPDIF
Firewire
USB2.0 Port
Ethernet
Modem
S-Video
Power-In
VGA Port
Card Reader
NewCard Slot
02 Micro 0Z128 (Card Reader)
Single Slot, 34mm type I supported
Multimedia Card (MMC), Secure Digital Card (SD),
Memory Stick (MS), and MS Pro Card
▼
Ports and Connectors
One Microphone-in / Line-in jack
One Headphone / SPDIF-out jack
One Firewire (IEEE1394) host connector
Three USB2.0-compliant connectors
One standard network Ethernet connector (RJ-45)
One modem / phone connector (RJ11)
One S-video (TV-out) output connector
One DC-in connector
One 15-pin VGA connector
One 4-in-1 Card Reader slot
One NewCard Slot (type I)
-5
■ Appendix A Product Specification
A
▼ Battery Pack / AC Adapter
Primary
Battery Pack
Feature
Adapter
AC-Input /
DC-Output
Li-ion 6-Cell pack, 10.8V / 11.1V x 4000 mAH or
Li-ion 6-Cell pack, 10.8V / 11.1V x 4400 mAH or
Li-ion 6-Cell pack, 10.8V / 11.1V x 4800 mAH
Low battery state with low battery warning beep
Uniwill SmartPower III Power Management
Smart Battery Compliant; low battery warning beep
Long Battery Life Mode and Silent Mode
Autosensing AC-in 100~240V, DC-out 20V, 65W
▼
BIOS
PnP Function
Self Test
Auto
Detection
Power
Management
Security
Other
Features
Phoenix PnP BIOS
Power On Self Test
DRAM auto-detection, auto-sizing
L2 Cache auto-detection
Hard disk type auto-detection
APM 1.2 (Advanced Power Management) &
ACPI 2.0 (Advanced Configuration Power Interface)
Two Level Password Protections
32bit access, Ultra DMA, PIO5 Mode support
Multi-boot capability
▼
Operating System
O/S
Compatible with Microsoft Windows XP Home Edition /
Professional SP2
-6
■ Appendix A Product Specification
A
▼
Physical Specification
Dimension
Weight
Environmental
Limits
332 (W) x 232 (D) x 23.5~33.8 (H) mm
2.4KG / 5.28lbs (with 14.1” LCD, DVD-ROM Drive and
6-cell battery pack)
Operating Temperature: 5 to 35
Operating Humidity: 20 to 80 percent RH (5 to 35
Storage Temperature: -15 to 50
o
C (41 to 95oF)
o
C (-5 to 122oF)
o
C)
-7
■ Appendix B Agency Regulatory Notices
APPENDIX▼ B
AGENCY REGULATORY NOTICES
B-1
■ Appendix B Agency Regulatory Notices
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interferen ce
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio or television technician
for help.
Modifications
The FCC requires the user to be notified that any changes or modifications
made to this device that are not expressly approved by the Manufacture
may void the user’s authority to operate the equipment.
Connections to Peripheral Devices
Connections to this device must be made with shielded cables with metallic
RFI/EMI connector hoods to maintain compliance with FCC Rules and
Regulations.
Declaration of Conformity
This device complies with Part 15(CLASS B
is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
European Notice
Products with the CE Marking comply with both the EMC Directive
(89/336/EEC) and the Low Voltage Directive (73/23/EEC) and R&TTE
Directive (1999/5/EC) issued by the Commission of the European
Community.
Compliance with these directives implies conformity to the following
European Norms:
B-2
)/68 the FCC Rules. Operation
■ Appendix B Agency Regulatory Notices
EN55022 : 1998+A1: 2000+A2: 2003, CLASS B
EN61000-3-2 : 2000
EN61000-3-3 : 1995+A1: 2001
EN55024 : 1998+A1 : 2001+A1: 2003
IEC61000-4-2: 2001
IEC61000-4-3:2002+A1:2002
IEC61000-4-4:1995+A1:2000+A2:2001
IEC61000-4-5:2001
IEC61000-4-6:2001
IEC61000-4-8:2001
IEC61000-4-11:2001
EN50082 (IEC801-2, IEC801-3, IEC801-4) Electro-magnetic
Immunity
EN 300 328-2, EN 300 328-1, EN 301 489-1, EN 301 489-17 (ETSI
300 328, ETSI 301 489) Electro-magnetic Compatibility and Radio
Spectrum Matter.
TBR21 ( ETSI TBR21) Terminal Equipment.
EN60950 (IEC60950) I.T.E. Product Safety
Canadian Notice
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the radio interference
regulations of the Canadian Department of Communications.
Le present appareil numerique nemet pas de bruits radioelectriques
depassant les limites applicables aux appareils numeriques de Classe B
prescrites dans le reglement sur le brouillage radioelectrique edicte par le
Ministere des Communications du Canada.
REN (Ringer Equivalent Numbers) Statement
''NOTICE: The Ringer Equivalence Number (REN) assigned to each
terminal device provides an indication of the maximum number of terminals
allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject onl y to the
requirement that the sum of the Ringer Equivalence Numbers of all the
devices does not exceed 5.''
IC ID: 3409A-M30EI0
B-3
■ Appendix B Agency Regulatory Notices
Attachment Limitations Statement
''Notice: This equipment meets telecommunications network protective,
operational and safety requirements as prescribed in the appropriate
Terminal Equipment Technical Requirements document(s). This is
confirmed by marking the equipment with the Industry Canada certification
number. The Department does not guarantee the equipment will operate to
the user's satisfaction.
Before installing this equipment, users should ensure that it is permissible
to be connected to the facilities of the local telecommunications company.
The equipment must also be installed using an acceptable method of
connection. The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative
designated by the supplier. Any repairs or alterations made by the user to
this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to disconnect the
equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic water
pipe system, if present, are connected together. This precaution may be
particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves,
but should contact the appropriate electric inspection authority, or
electrician, as appropriate.''
Power Cord Requirement
The power cord supplied with the AC adapter should match the plug and
voltage requirements for your local area. Regulatory approval for the AC
adapter has been obtained using the power cord for the local area.
However, if you travel to a different area and need to connect to a different
outlet or voltage, you should use one of the power cords listed below. To
purchase a power cord (including one for a country not listed below) or a
replacement ac adapter, contact your local dealer.
U.S. and Canada
The cord set must be UL-Listed and CSA-Certified or C-UL Listed.
The minimum specifications for the flexible cord are (1) No. 18 AWG,
B-4
(2) Type SJ, and (3) 3-conductor.
■ Appendix B Agency Regulatory Notices
The cord set must have a rated current capacity of at least 10 A.
The attachment plug must be an earth-grounding type with a NEMA
5-15P (15A, 125V) or NEMA 6-15P (15 A, 250V) configuration.
Japan
All components of the cord set (cord, connector, and plug) must bear
a `PSE` mark and registration number in accordance with the
Japanese Dentori Law.
The minimum specification for the flexible cord are: (1) 0.75 mm
2
conductors, (2) Type VCT or VCTF, and (3) 3-conductor.
The cord set must have minimum rated current capacity of 7 A.
The attachment plug must be a two-pole, grounded type with a
Japanese Industrial Standard C8303 (15 A, 125 VAC) configuration.
Other Countries
The cord set fittings must bear the certification mark of the agency
responsible for evaluation in a specific country. Acceptable agencies
are:
BSI (UK)
OVE (Australia)
CEBEC (Belgium)
SEMKO (Sweden)
FIMKO (Finland)
DEMKO (Denmark)
NEMKO (Norway)
SETI (Finland)
EANSW (Australia)
SEV (Switzerland)
IMQ (Italy)
UTE (France)
CCC (China)
PSB (Singapore)
PSE (Japan)
BSMI (Taiwan)
B (Polish)
VDE (Germany)
SASO (Saudi Arabia)
The flexible cord must be of a HAR (harmonized) type HO5VV-F
3-conductor cord with a minimum conductor size of 0.03 square
inches.
The minimum specification for the flexible cord for Class II product
are: (1) 2X0.75 mm
2
conductors, (2) 2-conductor cord.
B-5
■ Appendix B Agency Regulatory Notices
The cord set must have a current capacity of at least 10 A and a
nominal voltage rating of 125 / 250 VAC.
CAUTION: MODEL NB-14w2 IS DESIGNED TO USE WITH THE
FOLLOWING AC ADAPTER MODEL ONLY
Manufacture: LITE-ON ELECTRONICS, INC
Model: P PA-1650-02 (65W), PA-1650-01 (65W)
Manufacture: LI SHIN INTERNATIONAL ENTERPRISE CORP.
Model: 0335A2065 (65W), 0335C2065 (65W)
Manufacture: EPSF
Model: 10653-A (65W)
Telephone lines requirement
The appropriate utilization of 26AWG telephone line cord on unit.
CAUTION: Always disconnect all telephone lines from the wall outlet
before servicing or disassembling this equipment.
CAUTION: To reduc e the risk of fire, use only No. 26AWG or larger
telecommunication line cord.
Battery Pack Safety
The battery pack is intended to use only with this notebook.
Do not disassemble the pack.
Do not dispose of the battery pack in fire or water.
To avoid risk of fire, burns, or damage to your battery pack, do not
allow a metal object to touch the battery contacts.
Handle a damaged or leaking battery with extreme care. If you come
in contact with the electrolyte, wash the exposed area with soap and
water. If it contacts the eye, flush the eye with water for 15 minutes
and seek medical attention.
Do not charge the battery pack if the ambient temperature exceeds
45 (113 ).℃℉
To obtain a replacement battery, contact your local dealer.
Do not expose the battery pack to high storage temperatures (above
60 , 140 ).℃℉
When discarding a battery pack, contact your local waste disposal
provider regarding local restrictions on the disposal or recycling of
batteries.
Use only supplied AC Adapter for charging.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace
B-6
■ Appendix B Agency Regulatory Notices
only with same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions or local
laws.
VORSICHT! Explisionsgefahr bei unsachgernazen Austausch der Batterie.
Ersatz nur durch denselben oder einem vom Hersteller empfohlenem
ahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des
Herstellers.
Laser Safety
The optical drive used with this computer is certified as a Class 1 laser
device according to the U.S. Department of Health and Human Services
(DHHS) Radiation Performance Standard and International Standards IEC
825 / IEC 825-1 (EN60825 / EN60825-1). The device is not considered
harmful, but the following precautions are recommended:
Do not open the unit.
Avoid direct exposure to the laser beam.
If the unit requires service, contact an authorized service center.
Ensure proper use by reading and following the instructions carefully.
Do not attempt to make any adjustment of the unit.
CLASS 1 LASER PRODUCT
APPAREIL A LASER DE CLASSE 1
LASERSCHUTZKLASSE 1 PRODUKT
Warning!
Do not attempt to disassemble the cabinet containing the laser. The laser
beam used in this product is harmful to the eyes. The use of optical
instruments, such as magnifying lenses, with this product increase the
potential hazard to your eyes. For your safety, have this equipment
serviced only by an authorized service provider.
Lithium battery warning / Bridge battery warning
This computer contains a lithium battery to power the clock and calendar
circuitry.
CAUTION: Danger of explosion if battery is replaced incorrectly. Replace
only with the same or equivalent type recommended by the manufacturer.
B-7
■ Appendix B Agency Regulatory Notices
Discard used batteries according to the manufacturer’s instructions.
ATTENTION: Il y a danger d’xplosion s’il y a remplacement incorrect de la
batterie. Remplacer uniquement avcc unc batterie du meme type ou d’un
type recommande par le constructer. Mettre au rebut les batteries usagees
conformement aux instructions du fabricant.
VORSICHT! Explosionsgefahr bei unsachgemBen Austausch der Batterie
Ersatz nur durch denselben oder einem vom Hersteller empfohlenem
ahnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des
Herstellers.
Der Arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 betragt 70dB
(A) oder weniger.
Zum Netzanschlua dieses Gerates ist eine geprufte Leitung zu verwenden.
Fur einen Nennstrom bis 6A und einem Gerategewicht groBer 3kg ist eine
Leitung nicht leichter als (1)H05VV-F, 3G, 0.75mm
conductors
einzusetzen.
2
(2)2X0.75 mm
2
Die Steckdose muB nahe dem Gerat angebracht und leicht
zuganglich sein.
CAUTION!
T h is part i s ho t . B e Caref u l .
VORSICHT!
Diese Flache wird sehr heiss.
When you see this symbol, be careful as this spot may be very hot.
B-8
www.westinghousedigital.com
Westinghouse Digital Electronics
Santa Fe Springs, CA
SE-UM-1401-0601
Loading...